| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 771d6539f27bd55f43d8a95d53a7eeaaffa2681c ]
The back porch timings were correct, only the sync offset was wrong.
Correct timing is now reported for 1080i and 576i, but the h offset is
incorrect for 480i for non-obvious reasons.
Fixes: fb10dc451c0f ("drm/vc4: hdmi: Correct HDMI timing registers for interlaced modes")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20221207-rpi-hvs-crtc-misc-v1-14-1f8e0770798b@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 479d4f0be4237ba33bc9432787aeb62c90e30f95 ]
If vc4_hdmi_reset_link() returns -EDEADLK, it means that a deadlock
happened in the locking context. This situation should be addressed by
dropping all currently held locks and block until the contended lock
becomes available. Currently, vc4 is not dealing with the deadlock
properly, producing the following output when PROVE_LOCKING is enabled:
[ 825.612809] ------------[ cut here ]------------
[ 825.612852] WARNING: CPU: 1 PID: 116 at drivers/gpu/drm/drm_modeset_lock.c:276 drm_modeset_drop_locks+0x60/0x68 [drm]
[ 825.613458] Modules linked in: 8021q mrp garp stp llc
raspberrypi_cpufreq brcmfmac brcmutil crct10dif_ce hci_uart cfg80211
btqca btbcm bluetooth vc4 raspberrypi_hwmon snd_soc_hdmi_codec cec
clk_raspberrypi ecdh_generic drm_display_helper ecc rfkill
drm_dma_helper drm_kms_helper pwm_bcm2835 bcm2835_thermal bcm2835_rng
rng_core i2c_bcm2835 drm fuse ip_tables x_tables ipv6
[ 825.613735] CPU: 1 PID: 116 Comm: kworker/1:2 Tainted: G W 6.1.0-rc6-01399-g941aae326315 #3
[ 825.613759] Hardware name: Raspberry Pi 3 Model B Rev 1.2 (DT)
[ 825.613777] Workqueue: events output_poll_execute [drm_kms_helper]
[ 825.614038] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 825.614063] pc : drm_modeset_drop_locks+0x60/0x68 [drm]
[ 825.614603] lr : drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper]
[ 825.614829] sp : ffff800008313bf0
[ 825.614844] x29: ffff800008313bf0 x28: ffffcd7778b8b000 x27: 0000000000000000
[ 825.614883] x26: 0000000000000001 x25: 0000000000000001 x24: ffff677cc35c2758
[ 825.614920] x23: ffffcd7707d01430 x22: ffffcd7707c3edc7 x21: 0000000000000001
[ 825.614958] x20: 0000000000000000 x19: ffff800008313c10 x18: 000000000000b6d3
[ 825.614995] x17: ffffcd777835e214 x16: ffffcd7777cef870 x15: fffff81000000000
[ 825.615033] x14: 0000000000000000 x13: 0000000000000099 x12: 0000000000000002
[ 825.615070] x11: 72917988020af800 x10: 72917988020af800 x9 : 72917988020af800
[ 825.615108] x8 : ffff677cc665e0a8 x7 : d00a8c180000110c x6 : ffffcd77774c0054
[ 825.615145] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000
[ 825.615181] x2 : ffff677cc55e1880 x1 : ffffcd7777cef8ec x0 : ffff800008313c10
[ 825.615219] Call trace:
[ 825.615232] drm_modeset_drop_locks+0x60/0x68 [drm]
[ 825.615773] drm_helper_probe_detect+0x120/0x1b4 [drm_kms_helper]
[ 825.616003] output_poll_execute+0xe4/0x224 [drm_kms_helper]
[ 825.616233] process_one_work+0x2b4/0x618
[ 825.616264] worker_thread+0x24c/0x464
[ 825.616288] kthread+0xec/0x110
[ 825.616310] ret_from_fork+0x10/0x20
[ 825.616335] irq event stamp: 7634
[ 825.616349] hardirqs last enabled at (7633): [<ffffcd777831ee90>] _raw_spin_unlock_irq+0x3c/0x78
[ 825.616384] hardirqs last disabled at (7634): [<ffffcd7778315a78>] __schedule+0x134/0x9f0
[ 825.616411] softirqs last enabled at (7630): [<ffffcd7707aacea0>] local_bh_enable+0x4/0x30 [ipv6]
[ 825.617019] softirqs last disabled at (7618): [<ffffcd7707aace70>] local_bh_disable+0x4/0x30 [ipv6]
[ 825.617586] ---[ end trace 0000000000000000 ]---
Therefore, deal with the deadlock as suggested by [1], using the
function drm_modeset_backoff().
[1] https://docs.kernel.org/gpu/drm-kms.html?highlight=kms#kms-locking
Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221229194638.178712-1-mcanal@igalia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Issue is some displays go blank at the point of firmware to kms
handover. Plugging/unplugging hdmi cable, power cycling display, or
switching standby off/on
typically resolve this case.
Finally managed to find a display that suffers from this, and track down
the issue.
The firmware uses AVMUTE in normal operation. It will set AVMUTE before
disabling hdmi clocks and phy. It will clear AVMUTE after clocks and phy
are set up for a new hdmi mode.
But with the hdmi handover from firmware to kms, AVMUTE will be set by
firmware.
kms driver typically has no GCP packet (except for deep colour modes).
The spec isn't clear on whether to consider the AVMUTE as continuing
indefinitely in the absence of a GCP packet, or to consider that state
to have ended.
Most displays behave as we want, but there are a number (from multiple
manufacturers) which need to see AVMUTE cleared before displaying a
picture.
Lets just always enable GCP packet with AVMUTE cleared. That resolves
the issue on problematic displays.
From HDMI 1.4 spec:
A CD field of zero (Color Depth not indicated) shall be used whenever
the Sink does not indicate support for Deep Color. This value may
also be used in Deep Color mode to transmit a GCP indicating only
non-Deep Color information (e.g. AVMUTE).
So use CD=0 where we were previously not enabling a GCP.
Link: https://forum.libreelec.tv/thread/24780-le-10-0-1-rpi4-no-picture-after-update-from-le-10-0-0
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127161219.457058-1-maxime@cerno.tech
|
|
The bcm2711 has two HDMI outputs, each with their own CEC adapter.
The CEC adapter name has to be unique, but it is currently
hardcoded to "vc4" for both outputs. Change this to use the card_name
from the variant information in order to make the adapter name unique.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 15b4511a4af6 ("drm/vc4: add HDMI CEC support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/dcf1db75-d9cc-62cc-fa12-baf1b2b3bf31@xs4all.nl
|
|
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug") introduced
the vc4_hdmi_reset_link() function. This function dereferences the
"connector" pointer before checking whether it is NULL or not.
Rework variable assignment to avoid this issue.
Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20221110134752.238820-3-jose.exposito89@gmail.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Simplify vc4_hdmi_supports_scrambling() by changing its first parameter
from struct drm_encoder to struct vc4_hdmi.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20221110134752.238820-2-jose.exposito89@gmail.com
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.2:
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: locking improvements
- firmware: New API in the RaspberryPi firmware driver used by vc4
Core Changes:
- client: Null pointer dereference fix in drm_client_buffer_delete()
- mm/buddy: Add back random seed log
- ttm: Convert ttm_resource to use size_t for its size, fix for an
undefined behaviour
Driver Changes:
- bridge:
- adv7511: use dev_err_probe
- it6505: Fix return value check of pm_runtime_get_sync
- panel:
- sitronix: Fixes and clean-ups
- lcdif: Increase DMA burst size
- rockchip: runtime_pm improvements
- vc4: Fix for a regression preventing the use of 4k @ 60Hz, and
further HDMI rate constraints check.
- vmwgfx: Cursor improvements
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103083437.ksrh3hcdvxaof62l@houat
|
|
Commit ae71ab585c81 ("drm/vc4: hdmi: Enforce the minimum rate at
runtime_resume") reintroduced the call to clk_set_min_rate in an attempt
to fix the boot without a monitor connected on the RaspberryPi3.
However, that introduced a regression breaking the display output
entirely (black screen but no vblank timeout) on the Pi4.
This is due to the fact that we now have in a typical modeset at boot,
in vc4_hdmi_encoder_pre_crtc_configure(), we have a first call to
clk_set_min_rate() asking for the minimum rate of the HSM clock for our
given resolution, and then a call to pm_runtime_resume_and_get(). We
will thus execute vc4_hdmi_runtime_resume() which, since the commit
mentioned above, will call clk_set_min_rate() a second time with the
absolute minimum rate we want to enforce on the HSM clock.
We're thus effectively erasing the minimum mandated by the mode we're
trying to set. The fact that only the Pi4 is affected is due to the fact
that it uses a different clock driver that tries to minimize the HSM
clock at all time. It will thus lower the HSM clock rate to 120MHz on
the second clk_set_min_rate() call.
The Pi3 doesn't use the same driver and will not change the frequency on
the second clk_set_min_rate() call since it's still within the new
boundaries and it doesn't have the code to minimize the clock rate as
needed. So even though the boundaries are still off, the clock rate is
still the right one for our given mode, so everything works.
There is a lot of moving parts, so I couldn't find any obvious
solution:
- Reverting the original is not an option, as that would break the Pi3
again.
- We can't move the clk_set_min_rate() call in _pre_crtc_configure()
since because, on the Pi3, the HSM clock has the CLK_SET_RATE_GATE
flag which prevents the clock rate from being changed after it's
been enabled. Our calls to clk_set_min_rate() can change it, so they
need to be done before clk_prepare_enable().
- We can't remove the call to clk_prepare_enable() from the
runtime_resume hook to put it into _pre_crtc_configure() either,
since we need that clock to be enabled to access the registers, and
we can't count on the fact that the display will be active in all
situations (doing any CEC operation, or listing the modes while
inactive are valid for example()).
- We can't drop the call to clk_set_min_rate() in
_pre_crtc_configure() since we would need to still enforce the
minimum rate for a given resolution, and runtime_resume doesn't have
access to the current mode, if there's any.
- We can't copy the TMDS character rate into vc4_hdmi and reuse it
since, because it's part of the KMS atomic state, it needs to be
protected by a mutex. Unfortunately, some functions (CEC operations,
mostly) can be reentrant (through the CEC framework) and still need
a pm_runtime_get.
However, we can work around this issue by leveraging the fact that the
clk_set_min_rate() calls set boundaries for its given struct clk, and
that each different clk_get() call will return a different instance of
struct clk. The clock framework will then aggregate the boundaries for
each struct clk instances linked to a given clock, plus its hardware
boundaries, and will use that.
We can thus get an extra HSM clock user for runtime_pm use only, and use
our different clock instances depending on the context: runtime_pm will
use its own to set the absolute minimum clock setup so that we never
lock the CPU waiting for a register access, and the modeset part will
set its requirement for the current resolution. And we let the CCF do
the coordination.
It's not an ideal solution, but it's fairly unintrusive and doesn't
really change any part of the logic so it looks like a rather safe fix.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2136234
Fixes: ae71ab585c81 ("drm/vc4: hdmi: Enforce the minimum rate at runtime_resume")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20221021131339.2203291-1-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
A comment introduced by commit 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link
on hotplug") mentions a drm_atomic_helper_connector_hdmi_reset_link()
function that was part of the earlier versions but got moved internally
and is now named vc4_hdmi_reset_link(). Let's fix the function name.
Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20221024093634.118190-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
We access some fields protected by our internal mutex in
vc4_hdmi_reset_link() (saved_adjusted_mode, output_bpc, output_format)
and are calling functions that need to have that lock taken
(vc4_hdmi_supports_scrambling()).
However, the current code doesn't lock that mutex. Let's make sure it
does.
Fixes: 6bed2ea3cb38 ("drm/vc4: hdmi: Reset link on hotplug")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20221024093634.118190-1-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
At least the 4096x2160@60Hz mode requires some overclocking that isn't
available by default, even if hdmi_enable_4kp60 is enabled.
Let's add some logic to detect whether we can satisfy the core clock
requirements for that mode, and prevent it from being used otherwise.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-6-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
This will have the side-effect of raising the maximum of the core clock,
tied to the HVS, and managed by the HVS driver.
However, we are querying this in the HDMI driver by poking into the HVS
structure to get our struct clk handle.
Let's make this part of the HVS bind implementation to have all the core
clock related setup in the same place.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-5-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
In order to support higher HDMI frequencies, users have to set the
hdmi_enable_4kp60 parameter in their config.txt file.
We were detecting this so far by calling clk_round_rate() on the core
clock with the frequency we're supposed to run at when one of those
modes is enabled. Whether or not the parameter was enabled could then be
inferred by the returned rate since the maximum clock rate reported by
the firmware was one of the side effect of setting that parameter.
However, the recent clock rework we did changed what clk_round_rate()
was returning to always return the minimum allowed, and thus this test
wasn't reliable anymore.
Let's use the new clk_get_max_rate() function to reliably determine the
maximum rate allowed on that clock and fix the 4k@60Hz output.
Fixes: e9d6cea2af1c ("clk: bcm: rpi: Run some clocks at the minimum rate allowed")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-4-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.2:
UAPI Changes:
- Documentation for page-flip flags
Cross-subsystem Changes:
- dma-buf: Add unlocked variant of vmapping and attachment-mapping
functions
Core Changes:
- atomic-helpers: CRTC primary plane test fixes
- connector: TV API consistency improvements, cmdline parsing
improvements
- crtc-helpers: Introduce drm_crtc_helper_atomic_check() helper
- edid: Fixes for HFVSDB parsing,
- fourcc: Addition of the Vivante tiled modifier
- makefile: Sort and reorganize the objects files
- mode_config: Remove fb_base from drm_mode_config_funcs
- sched: Add a module parameter to change the scheduling policy,
refcounting fix for fences
- tests: Sort the Kunit tests in the Makefile, improvements to the
DP-MST tests
- ttm: Remove unnecessary drm_mm_clean() call
Driver Changes:
- New driver: ofdrm
- Move all drivers to a common dma-buf locking convention
- bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
- ast: Atomic Gamma LUT Support, Convert to SHMEM, various
improvements
- lcdif: Support for YUV planes
- mgag200: Fix PLL Setup on some revisions
- udl: Modesetting improvements, hot-unplug support
- vc4: Fix support for PAL-M
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020072405.g3o4hxuk75gmeumw@houat
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* vc4: HDMI fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y0gGdlujszCstDeP@linux-uq9g
|
|
Backmerging to get v6.1-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
If our HSM clock has not been properly initialized, any register access
will silently lock up the system.
Let's check that this can't happen by adding a check for the rate before
any register access, and error out otherwise.
Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-2-cd22e962296c@cerno.tech
|
|
This is a revert of commit fd5894fa2413 ("drm/vc4: hdmi: Remove clock
rate initialization"), with the code slightly moved around.
It turns out that we can't downright remove that code from the driver,
since the Pi0-3 and Pi4 are in different cases, and it only works for
the Pi4.
Indeed, the commit mentioned above was relying on the RaspberryPi
firmware clocks driver to initialize the rate if it wasn't done by the
firmware. However, the Pi0-3 are using the clk-bcm2835 clock driver that
wasn't doing this initialization. We therefore end up with the clock not
being assigned a rate, and the CPU stalling when trying to access a
register.
We can't move that initialization in the clk-bcm2835 driver, since the
HSM clock we depend on is actually part of the HDMI power domain, so any
rate setup is only valid when the power domain is enabled. Thus, we
reinstated the minimum rate setup at runtime_suspend, which should
address both issues.
Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/
Fixes: fd5894fa2413 ("drm/vc4: hdmi: Remove clock rate initialization")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-1-cd22e962296c@cerno.tech
|
|
ambiguity
We currently have two sets of TV properties.
The first one is there to deal with analog TV properties, creating
properties such as the TV mode, subconnectors, saturation, hue and so on.
It's created by calling the drm_mode_create_tv_properties() function.
The second one is there to deal with properties that might be useful on a
TV, creating the overscan margins for example. It's created by calling the
drm_mode_create_tv_margin_properties().
However, we also have a drm_atomic_helper_connector_tv_reset() function
that will reset the TV margin properties to their default values, and thus
is supposed to be called for the latter set. This creates an ambiguity due
to the inconsistent naming.
We can thus rename the drm_atomic_helper_connector_tv_reset() function to
drm_atomic_helper_connector_tv_margins_reset() to remove that ambiguity
and hopefully make it more obvious.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://lore.kernel.org/r/20220728-rpi-analog-tv-properties-v4-4-60d38873f782@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
We need 6.0-rc1 to merge the backlight rework PR.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.
However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.
The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.
The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.
As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:
* i915 has fairly different structures than simpler KMS drivers such
as vc4, so doing some code that works with both proved to be
difficult;
* Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
it would still require to move some parameters currently stored in
private structure that are needed to compute whether the scrambling
is needed or not, and then inform the driver that it needs to be
enabled. Some of those parameters are already in core structures
(drm_display_mode, drm_display_info, bpc), but the output format
isnt't. Adding it is fairly challenging since unlike the TMDS char
rate or mode, there's no consensus on what format to pick in
drivers, so it's not possible to write some generic code that can
depend on it.
For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-8-maxime@cerno.tech
|
|
We'll need it earlier in the driver, so let's move it next to the other
scrambling-related helpers.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-7-maxime@cerno.tech
|
|
We'll need the locking context in future patch, so let's convert .detect
to .detect_ctx.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-6-maxime@cerno.tech
|
|
Our detect callback has a bunch of operations to perform depending on
the current and last status of the connector, such a setting the CEC
physical address or enabling the scrambling again.
This is currently dealt with a bunch of if / else statetements that make
it fairly difficult to read and extend.
Let's move all that logic to a function of its own.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-5-maxime@cerno.tech
|
|
We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.
However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.
Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.
However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().
Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-4-maxime@cerno.tech
|
|
Even though vc4_hdmi_supports_scrambling takes a mode as an argument, it
never uses it. Let's remove it.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-3-maxime@cerno.tech
|
|
We don't modify the drm_display_mode pointer we have in the driver in
most places, so let's make them const.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-2-maxime@cerno.tech
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.1:
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f0c71766-61e8-19b7-763a-5fbcdefc633d@linux.intel.com
|
|
In vc4_hdmi_encoder_{pre,post}_crtc_enable() commit cd00ed5187bf
("drm/vc4: hdmi: Protect device resources after removal") missed to
unlock the mutex before returning due to drm_dev_enter() indicating the
device being unplugged.
Fixes: cd00ed5187bf ("drm/vc4: hdmi: Protect device resources after removal")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220824161327.330627-2-dakr@redhat.com
|
|
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit 53565c28e6af2cef6bbf438c34250135e3564459)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
We already depend on runtime PM to get the power domains and clocks for
most of the devices supported by the vc4 driver, so let's just select it
to make sure it's there.
Link: https://lore.kernel.org/r/20220629123510.1915022-38-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit f1bc386b319e93e56453ae27e9e83817bb1f6f95)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This driver includes the deprecated OF GPIO header <linux/of_gpio.h>
yet fail to use symbols from it, so drop the include.
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220812205746.609107-6-mairacanal@riseup.net
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows, we've had lots of developments in a wide range
at this time; the majority of changes are about ASoC, including
subsystem-wide cleanups, continued SOF / Intel updates and a bunch of
new drivers (as usual), while there have been some significant (but
almost invisible) improvements in ALSA core side, too.
Below are some highlights:
Core:
- Faster lookups of control elements with Xarray; normal user won't
notice, but on the devices with tons of control elements, it can be
visibly faster
- Support for input validation for controls; this will harden for
badly written drivers in general with a slight overhead
- Deferred async signal handling for working around the potential
deadlocks
- Cleanup / refactoring raw MIDI locking code
ASoC:
- Restructing of the set_fmt() callbacks for making things clearer in
situations like CODEC to CODEC links
- Clean up and modernizing the DAI naming scheme setups
- Merge of more of the Intel AVS driver stack, including some board
integrations
- New version 4 mechanism for communication with SOF DSPs
- Suppoort for dynamically selecting the PLL to use at runtime on
i.MX platforms
- Improvements for CODEC to CODEC support in the generic cards
- Support for AMD Jadeite and various machines, AMD RPL, Intel
MetorLake DSPs, Mediatek MT8186 DSPs and MT6366, nVidia Tegra
MDDRC, OPE and PEQ, NXP TFA9890, Qualcomm SDM845, WCD9335 and
WAS883x, and Texas Instruments TAS2780
HD- and USB-audio:
- Continued improvement for CS35L41 (sub)codec support
- More quirks for various devices (HP, Lenovo, Dell, Clevo)"
* tag 'sound-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (778 commits)
ALSA: hda/realtek: Add quirk for HP Spectre x360 15-eb0xxx
ALSA: line6: Replace sprintf() with sysfs_emit()
ALSA: hda: Replace sprintf() with sysfs_emit()
ALSA: pcm: Replace sprintf() with sysfs_emit()
ALSA: core: Replace scnprintf() with sysfs_emit()
ALSA: control-led: Replace sprintf() with sysfs_emit()
ALSA: aoa: Replace sprintf() with sysfs_emit()
ALSA: ac97: Replace sprintf() with sysfs_emit()
ALSA: hda/realtek: Add quirk for Clevo NV45PZ
ALSA: hda/realtek: Add quirk for Lenovo Yoga9 14IAP7
ALSA: control: Use deferred fasync helper
ALSA: pcm: Use deferred fasync helper
ALSA: timer: Use deferred fasync helper
ALSA: core: Add async signal helpers
ASoC: q6asm: use kcalloc() instead of kzalloc()
ACPI: scan: Add CLSA0101 Laptop Support
ALSA: hda: cs35l41: Support CLSA0101
ALSA: hda: cs35l41: Use the CS35L41 HDA internal define
ASoC: dt-bindings: use spi-peripheral-props.yaml
ASoC: codecs: va-macro: use fsgen as clock
...
|
|
mutex_init is supposed to be balanced by a call to mutex_destroy that we
were never doing in the vc4 driver.
Since a DRM-managed mutex_init variant has been introduced, let's just
switch to it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-66-maxime@cerno.tech
|
|
The vc4 has a custom API to allow components to register a debugfs file
before the DRM driver has been registered and the debugfs_init hook has
been called.
However, the .late_register hook allows to have the debugfs file creation
deferred after that time already.
Let's remove our custom code to only register later our debugfs entries as
part of either debugfs_init or after it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-65-maxime@cerno.tech
|
|
devm_pm_runtime_enable() simplifies the driver a bit since it will call
pm_runtime_disable() automatically through a device-managed action.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-49-maxime@cerno.tech
|
|
Whenever the device and driver are unbound, the main device and all the
subdevices will be removed by calling their unbind() method.
However, the DRM device itself will only be freed when the last user will
have closed it.
It means that there is a time window where the device and its resources
aren't there anymore, but the userspace can still call into our driver.
Fortunately, the DRM framework provides the drm_dev_enter() and
drm_dev_exit() functions to make sure our underlying device is still there
for the section protected by those calls. Let's add them to the HDMI driver.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-48-maxime@cerno.tech
|
|
The HDMI driver unbind hook doesn't have any ALSA-related code anymore, so
let's move the ALSA sanity checks and comments we have to some other part
of the driver dedicated to ALSA.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-47-maxime@cerno.tech
|
|
Commit 776efe800fed ("drm/vc4: hdmi: Drop devm interrupt handler for
hotplug interrupts") dropped the device-managed interrupt registration
because it was creating bugs and races whenever an interrupt was coming in
while the device was removed.
However, our latest patches to the HDMI controller driver fix this as well,
so we can use device-managed interrupt handlers again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-46-maxime@cerno.tech
|
|
The current code to build the registers set later exposed in debugfs for
the HDMI controller relies on traditional allocations, that are later
free'd as part of the driver unbind hook.
Since krealloc doesn't have a DRM-managed equivalent, let's add an action
to free the buffer later on.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-45-maxime@cerno.tech
|
|
The reference to the DDC controller device needs to be put back when we're
done with it. Let's use a device-managed action to simplify the driver.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-44-maxime@cerno.tech
|
|
The current code to unregister our CEC device needs to be undone manually
when we remove the HDMI driver.
Since the CEC framework will allocate its main structure, and will defer
its deallocation to when the last user will have closed it, we don't really
need to take any particular measure to prevent any use-after-free and can
thus use any managed action.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-43-maxime@cerno.tech
|
|
The current code to unregister our ALSA device needs to be undone manually
when we remove the HDMI driver.
Since ALSA doesn't seem to support any mechanism to defer freeing something
until the last user of the ALSA device is gone, we can either use a
device-managed or a DRM-managed action.
The consistent way would be to use a DRM-managed one, just like pretty much
any framework-facing structure should be doing. However, ALSA does a lot of
allocation and registration using device-managed calls. Thus, if we're
going that way, by the time the DRM-managed action would run all of those
allocation would have been freed and we would end up with a use-after-free.
Thus, let's do a device-managed action. It's been tested with KASAN enabled
and doesn't seem to trigger any issue, so it's as good as anything.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-42-maxime@cerno.tech
|
|
The current code will call drm_connector_unregister() and
drm_connector_cleanup() when the device is unbound. However, by then, there
might still be some references held to that connector, including by the
userspace that might still have the DRM device open.
Let's switch to a DRM-managed initialization to clean up after ourselves
only once the DRM device has been last closed.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-41-maxime@cerno.tech
|
|
The current code will call drm_encoder_cleanup() when the device is
unbound. However, by then, there might still be some references held to
that encoder, including by the userspace that might still have the DRM
device open.
Let's switch to a DRM-managed initialization to clean up after ourselves
only once the DRM device has been last closed.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-40-maxime@cerno.tech
|
|
drm_connector_unregister() is only to be used for connectors that have been
registered through drm_connector_register() after drm_dev_register() has
been called. This is our case here so let's remove the call.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-39-maxime@cerno.tech
|
|
Our internal structure that stores the DRM entities structure is allocated
through a device-managed kzalloc.
This means that this will eventually be freed whenever the device is
removed. In our case, the most likely source of removal is that the main
device is going to be unbound, and component_unbind_all() is being run.
However, it occurs while the DRM device is still registered, which will
create dangling pointers, eventually resulting in use-after-free.
Switch to a DRM-managed allocation to keep our structure until the DRM
driver doesn't need it anymore.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220711173939.1132294-38-maxime@cerno.tech
|
|
I need to have some vc4 patches merged in -rc4, but drm-misc-next is
only at -rc2 for now.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
