| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix the AUX_CMD_SEND bit for ti,sn65dsi86 bridge chip. With wrong
value the dpcd aux transactions with eDP panel are failing.
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181130092745.4219-1-spanda@codeaurora.org
|
|
Let's solve the mystery of commit bf1178c98930 ("drm/bridge:
ti-sn65dsi86: Add mystery delay to enable()"). Specifically the
reason we needed that mystery delay is that we weren't paying
attention to HPD.
Looking at the datasheet for the same panel that was tested for the
original commit, I see there's a timing "t3" that times from power on
to the aux channel being operational. This time is specced as 0 - 200
ms. The datasheet says that the aux channel is operational at exactly
the same time that HPD is asserted.
Scoping the signals on this board showed that HPD was asserted 84 ms
after power was asserted. That very closely matches the magic 70 ms
delay that we had. ...and actually, in my testing the 70 ms wasn't
quite enough of a delay and some percentage of the time the display
didn't come up until I bumped it to 100 ms (presumably 84 ms would
have worked too).
To solve this, we tried to hook up the HPD signal in the bridge.
...but in doing so we found that that the bridge didn't report that
HPD was asserted until ~280 ms after we powered it (!). This is
explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD
(Hot Plug/Unplug Detection)". Reading there we see that the bridge
isn't even intended to report HPD until 100 ms after it's asserted.
...but that would have left us at 184 ms. The extra 100 ms
(presumably) comes from this part in the datasheet:
> The HPD state machine operates off an internal ring oscillator. The
> ring oscillator frequency will vary [ ... ]. The min/max range in
> the HPD State Diagram refers to the possible times based off
> variation in the ring oscillator frequency.
Given that the 280 ms we'll end up delaying if we hook up HPD is
_slower_ than the 200 ms we could just hardcode, for now we'll solve
the problem by just hardcoding a 200 ms delay in the panel driver
using the patch in this series ("drm/panel: simple: Support panels
with HPD where HPD isn't connected").
If we later find a panel that needs to use this bridge where we need
HPD then we'll have to come up with some new code to handle it. Given
the silly debouncing in the bridge chip, though, it seems unlikely.
One last note is that I tried to solve this through another way: In
ti_sn_bridge_enable() I tried to use various combinations of
dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel
was up. In theory that would let me detect _exactly_ when I could
continue and do link training. Unfortunately even if I did an aux
transfer w/out waiting I couldn't see any errors. Possibly I could
keep looping over link training until it came back with success, but
that seemed a little overly hacky to me.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org
|
|
The THC63LVD1024 is restricted to a pixel clock frequency in the range
of 8 to 135 MHz. Implement the bridge .mode_valid() operation
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
The Analogix DP bridge driver is pretty verbose, and outputs
things like
[ 619.414067] rockchip-dp ff970000.edp: Link Training Clock Recovery success
[ 619.429233] rockchip-dp ff970000.edp: Link Training success!
each time the display gets unblanked. While it is good to know
that the device is behaving correctly, users already know that
because they can see some video output.
Let's keep these messages for cases where we need to actually
debug the driver (we have dynamic debug to enable them at runtime
if need be), and let's keep the kernel quiet otherwise.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180805172857.2517-1-marc.zyngier@arm.com
|
|
This patch adds a 70ms mystery delay to the bridge driver in enable.
By experimentation, it seems like it can go anywhere up until we
initiate semi-auto link training. If we don't have the delay, link
training fails.
I tried to root cause this as best I could, but neither the datasheet
for the panel nor the bridge mention a delay of this magnitude in their
timing requirements. So for now, add the mystery delay until someone
figures out a better fix.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-8-sean@poorly.run
|
|
Now that 4.19-rc1 is cut, backmerge it into -misc-next.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
|
|
0day reports:
>> drivers/gpu/drm/bridge/ti-sn65dsi86.o: In function
mipi_dsi_detach'
>> drivers/gpu/drm/bridge/ti-sn65dsi86.c:630: undefined reference to
ti_sn_bridge_attach':
>> drivers/gpu/drm/bridge/ti-sn65dsi86.c:249: undefined reference to
mipi_dsi_device_register_full'
>> drivers/gpu/drm/bridge/ti-sn65dsi86.c:276: undefined reference to
mipi_dsi_device_unregister'
Quite obviously the driver depends on DRM_MIPI_DSI.
We can not use depends since the driver configuration uses select,
so we'll have to select the missing dependency instead.
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Dylan Reid <dgreid@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180815194923.3258-1-sean@poorly.run
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
|
|
Instead of just waiting 20ms for training to complete, actually poll the
status to ensure training is finished.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-7-sean@poorly.run
|
|
Instead of just waiting and hoping, actually poll for the pll lock to be
acquired. As a bonus, this should be significantly faster than the
sleep.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-6-sean@poorly.run
|
|
prepare() is the old-timey way to say pre_enable(). It should be called
before modeset. This fixes an issue where the panel on cheza must have
the regulator always-on/boot-on for it to work.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-5-sean@poorly.run
|
|
This was hand-rolled in the first version, and will surely be useful as
we expand the driver to support more varied use cases.
Changes in v2:
- Change subject prefix s/panel/bridge/
- Downgrade warning in poll function to error message
- Fix DP_EDP_CONFIGURATION_SET write value (Sandeep)
- Mask upper 8 bits of msg->address (Sandeep)
- Check aux cmd status for errors after completing the send (Sandeep)
- Remove length check since it's covered in the aux status
- Flip the READ check in transfer to WRITE check + early exit
Changes in v3:
- Added to the set
- Wrapped (x) in WDATA/RDATA #defines
- Replace readx_poll* with regmap_read_poll*
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-4-sean@poorly.run
|
|
Order registers by offset and rename bits & masks to match the
datasheet. This makes the driver a bit easier to grok and
cross-reference with the datasheet.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-3-sean@poorly.run
|
|
drm_mode_connector_attach_encoder
This function name was changed to drm_connector_attach_encoder().
Unfortunately this driver was posted on the list before that change, and
applied after
Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge
driver")
Cc: Sandeep Panda <spanda@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730174225.257255-1-seanpaul@chromium.org
|
|
Recently drm_mode_connector_attach_encoder changed it's name. The change
was not noticed by bridge author, as a result gcc reports compile error
on next branch.
Fixes: f38b7cca6d0e ("drm/bridge: tc358764: Add DSI to LVDS bridge driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727094859.27727-1-a.hajda@samsung.com
|
|
rmk requested this for armada and I think we've had a few
conflicts build up.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Please do not comment out unneeded code. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532496348-11589-1-git-send-email-yamada.masahiro@socionext.com
|
|
Add a drm_bridge driver for the Toshiba TC358764 DSI to LVDS bridge.
Changes in v4:
- removed license blob,
- ordered includes,
- added error handling,
- fixed reset GPIO handling,
- added missing calls to the panel,
- custom OF graph code replaced with helpers,
- removed tc358764_poweroff from remove callback.
v5:
- fixed supply names,
- fixed broken console - added connector to fb_helper,
- added detach callback - unbinding works,
- fixed typo in error checking code,
- removed sparse bridge->encoder check - core does it already.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
[ a.hajda@samsung.com: v4, v5 ]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725154644.25412-6-a.hajda@samsung.com
|
|
Add support for TI's sn65dsi86 dsi2edp bridge chip.
The chip converts DSI transmitted signal to eDP signal,
which is fed to the connected eDP panel.
This chip can be controlled via either i2c interface or
dsi interface. Currently in driver all the control registers
are being accessed through i2c interface only.
Also as of now HPD support has not been added to bridge
chip driver.
Changes in v1:
- Split the dt-bindings and the driver support into separate patches
(Andrzej Hajda).
- Use of gpiod APIs to parse and configure gpios instead of obsolete ones
(Andrzej Hajda).
- Use macros to define the register offsets (Andrzej Hajda).
Changes in v2:
- Separate out edp panel specific HW resource handling from bridge
driver and create a separate edp panel drivers to handle panel
specific mode information and HW resources (Sean Paul).
- Replace pr_* APIs to DRM_* APIs to log error or debug information
(Sean Paul).
- Remove some of the unnecessary structure/variable from driver (Sean
Paul).
- Rename the function and structure prefix "sn65dsi86" to "ti_sn_bridge"
(Sean Paul / Rob Herring).
- Remove most of the hard-coding and modified the bridge init sequence
based on current mode (Sean Paul).
- Remove the existing function to retrieve the EDID data and
implemented this as an i2c_adapter and use drm_get_edid() (Sean Paul).
- Remove the dummy irq handler implementation, will add back the
proper irq handling later (Sean Paul).
- Capture the required enable gpios in a single array based on dt entry
instead of having individual descriptor for each gpio (Sean Paul).
Changes in v3:
- Remove usage of irq_gpio and replace it as "interrupts" property (Rob
Herring).
- Remove the unnecessary header file inclusions (Sean Paul).
- Rearrange the header files in alphabetical order (Sean Paul).
- Use regmap interface to perform i2c transactions.
- Update Copyright/License field and address other review comments
(Jordan Crouse).
Changes in v4:
- Update License/Copyright (Sean Paul).
- Add Kconfig and Makefile changes (Sean Paul).
- Drop i2c gpio handling from this bridge driver, since i2c sda/scl gpios
will be handled by i2c master.
- Update required supplies names.
- Remove unnecessary goto statements (Sean Paul).
- Add mutex lock to power_ctrl API to avoid race conditions (Sean
Paul).
- Add support to parse reference clk frequency from dt(optional).
- Update the bridge chip enable/disable sequence.
Changes in v5:
- Fixed Kbuild test service reported warnings.
Changes in v6:
- Use PM runtime based ref-counting instead of local ref_count mechanism
(Stephen Boyd).
- Clean up some debug logs and indentations (Sean Paul).
- Simplify dp rate calculation (Sean Paul).
- Add support to configure refclk based on input REFCLK pin or DACP/N
pin (Stephen Boyd).
Changes in v7:
- Use static supply entries instead of dynamic allocation (Andrzej
Hajda).
- Defer bridge driver probe if panel is not probed (Andrzej Hajda).
- Update of_graph APIs for correct node reference management. (Andrzej
Hajda).
- Remove local display_mode object (Andrzej Hajda).
- Remove version id check function from driver.
Changes in v8:
- Move dsi register/attach function to bridge driver probe (Andrzej
Hajda).
- Introduce a new helper function to write 16bit words into consecutive
registers (Andrzej Hajda).
- Remove unnecessary macros (Andrzej Hajda).
Changes in v9:
- Remove dsi register/attach from bridge probe, since dsi dev register
completion also waits for any panel or bridge to get added. This creates
deadlock situation when bridge driver calls dsi dev register and
attach before bridge add, in its probe function.
- Fix issues faced during testing of bridge driver on actual HW.
- Remove unnecessary initializations (Stephen Boyd).
- Use local refclk lut size instead of global macro (Sean Paul).
Changes in v10:
- Use refclk to determine if continuous dsi clock is needed or not.
Changes in v11:
- Read DPPLL_SRC register to determine continuous clock instead of
using refclk handle (Stephen Boyd).
Changes in v12:
- Explain in comment as in why dsi dev registration is done in
bridge_attach (Andrzej Hajda).
- Move HPD disable to bridge_pre_enable (Andrzej Hajda).
- Make panel/DDC exclusive until HPD support is added (Andrzej Hajda).
Changes in v13:
- eDP panels report EDID via DP-AUX channel, so remove support for
dedicated DDC line (Andrzej Hajda).
Changes in v14:
- Remove unnecessary drm_panel checks (Andrzej Hajda).
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532069642-21392-1-git-send-email-spanda@codeaurora.org
|
|
Again to align with the usual prefix of just drm_connector_. Again
done with sed + manual fixup for indent issues.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-7-daniel.vetter@ffwll.ch
|
|
Just makes it longer, and for most things in drm_connector.[hc] we
just use the drm_connector_ prefix. Done with sed + a bit of manual
fixup for the indenting.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180709084016.23750-6-daniel.vetter@ffwll.ch
|
|
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
|
|
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org
|
|
Current link mode values do not allow to enable packed pixel modes.
Select packed pixel clock mode, if needed, every time the link mode
register gets updated.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-4-git-send-email-m.purski@samsung.com
|
|
Current implementation does not guarantee packed pixel modes working
with every dongle. There are some dongles, which require selecting
the output mode explicitly.
Write proper values to registers in packed_pixel mode, based on how it
is done in vendor's code. Select output color space: RGB
(no packed pixel) or YCBCR422 (packed pixel).
This reverts commit e8b92efa629dac0e70ea4145c5e70616de5f89c8
("drm/bridge/sii8620: fix display of packed pixel modes in MHL2").
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-3-git-send-email-m.purski@samsung.com
|
|
Currently AVI infoframe is sent only in MHL3. However, some MHL2 dongles
need AVI infoframe to work correctly in either packed pixel mode or
non-packed pixel mode.
Send AVI infoframe in set_infoframes() in every case. Create an
infoframe using drm_hdmi_infoframe_from_display_mode() instead of
manually filling each infoframe structure's field.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-2-git-send-email-m.purski@samsung.com
|
|
https://github.com/bzolnier/linux into drm-misc-next
Immutable branch between fbdev and drm for the v4.19 merge window
(contains the deferred console takeover feature)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
# gpg: Signature made Thu 28 Jun 2018 10:24:50 AM -03
# gpg: using RSA key 7E33B63FA047C20B
# gpg: Can't check signature: public key not found
# Conflicts:
# drivers/gpu/drm/i915/i915_gem.c
# drivers/gpu/drm/i915/intel_crt.c
# drivers/gpu/drm/i915/intel_display.c
# drivers/gpu/drm/i915/intel_lrc.c
Link: https://patchwork.freedesktop.org/patch/msgid/2462549.rLSfW9kX99@amdc3058
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.19:
UAPI Changes:
- Add writeback connector (Brian Starkey/Liviu Dudau)
- Add "content type" property to HDMI connectors (Stanislav Lisovskiy)
Cross-subsystem Changes:
- some devicetree Docs update
- fix compile breakage on ION due to the dma-buf cleanups (Christian König)
Core Changes:
- Reject over-sized allocation requests early (Chris Wilson)
- gem-fb-helper: Always do implicit sync (Daniel Vetter)
- dma-buf cleanups (Christian König)
Driver Changes:
- Fixes for the otm8009a panel driver (Philippe Cornu)
- Add Innolux TV123WAM panel driver support (Sandeep Panda)
- Move GEM BO to drm_framebuffer in few drivers (Daniel Stone)
- i915 pinning improvements (Chris Wilson)
- Stop consulting plane->fb/crtc in a few drivers (Ville Syrjälä)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621105428.GA20795@juma
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
|
|
Currently packed pixel modes in MHL2 can't be displayed. The device
automatically recognizes output format, so setting format other than
RGB causes failure. Fix it by writing proper values to registers.
Tested on MHL1 and MHL2 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516706239-9104-1-git-send-email-m.purski@samsung.com
|
|
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
|
|
This patch makes RC_CORE to be selected with this driver.
sil_sii8620 driver calls remote controller interfaces directly
so RC_CORE should be enabled mandatorily.
And some boards not using remote controller device don't really
need to know that RC_CORE config should be enabled to use sil_sii8620
driver only for HDMI.
Changelog v2:
- select INPUT because compiling will fail without INPUT.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527154379-31886-1-git-send-email-inki.dae@samsung.com
|
|
MHL bridge is usually connected to TV via MHL dongle. Currently plugging
HDMI cable to dongle is handled improperly.
Fix it by splitting connecting of a dongle and a HDMI cable. The driver
should now handle unplugging a sink from a dongle and plugging a
different sink with new edid.
Tested on MHL1, MHL2 and MHL3 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516705996-8928-1-git-send-email-m.purski@samsung.com
|
|
HSIC initialization was taken from the vendor code. HSIC in MHL circuit
is not connected, so it is not possible to test it. Tests prove that
without HSIC the device works well. Therefore it can be removed.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511968368-30884-1-git-send-email-m.purski@samsung.com
|
|
The vendor code waits for infoframe to detect video mode set by source.
We do not need to follow this pattern, because video mode information is
provided by drm core. As a result most of the infoframe handling
code can be removed.
Start transmission immediately after detecting stream on HDMI lines
in irq_scdt() function without waiting for infoframe interrupt.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511956130-24482-1-git-send-email-m.purski@samsung.com
|
|
Buffer overflow error should not occur, as mode_fixup() callback
filters pixel clock value and it should never exceed 600000. However,
current implementation is not obviously safe and relies on
implementation of mode_fixup().
Make 'i' variable never reach unsafe value in order to avoid buffer
overflow error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: bf1722ca ("drm/bridge/sii8620: rewrite hdmi start sequence")
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511341718-6974-1-git-send-email-m.purski@samsung.com
|
|
Current implementation of mode_valid() and mode_fixup() callbacks
handle packed pixel modes improperly.
Fix it by using proper maximum clock values from the documentation.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1517568865-25219-1-git-send-email-m.purski@samsung.com
|
|
Function should constantly check if cable is connected and finish
in finite time.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Maciej Purski <m.purski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115173357.31067-4-a.hajda@samsung.com
|
|
There is no need to flip reset pin twice. Also delays can be changed to
values present in vendor's code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Maciej Purski <m.purski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608060457.18357-1-a.hajda@samsung.com
|
|
Pull drm updates from Dave Airlie:
"This starts to support NVIDIA volta hardware with nouveau, and adds
amdgpu support for the GPU in the Kabylake-G (the intel + radeon
single package chip), along with some initial Intel icelake enabling.
Summary:
New Drivers:
- v3d - driver for broadcom V3D V3.x+ hardware
- xen-front - XEN PV display frontend
core:
- handle zpos normalization in the core
- stop looking at legacy pointers in atomic paths
- improved scheduler documentation
- improved aspect ratio validation
- aspect ratio support for 64:27 and 256:135
- drop unused control node code.
i915:
- Icelake (ICL) enabling
- GuC/HuC refactoring
- PSR/PSR2 enabling and fixes
- DPLL management refactoring
- DP MST fixes
- NV12 enabling
- HDCP improvements
- GEM/Execlist/reset improvements
- GVT improvements
- stolen memory first 4k fix
amdgpu:
- Vega 20 support
- VEGAM support (Kabylake-G)
- preOS scanout buffer reservation
- power management gfxoff support for raven
- SR-IOV fixes
- Vega10 power profiles and clock voltage control
- scatter/gather display support on CZ/ST
amdkfd:
- GFX9 dGPU support
- userptr memory mapping
nouveau:
- major refactoring for Volta GV100 support
tda998x:
- HDMI i2c CEC support
etnaviv:
- removed unused logging code
- license text cleanups
- MMU handling improvements
- timeout fence fix for 50 days uptime
tegra:
- IOMMU support in gr2d/gr3d drivers
- zpos support
vc4:
- syncobj support
- CTM, plane alpha and async cursor support
analogix_dp:
- HPD and aux chan fixes
sun4i:
- MIPI DSI support
tilcdc:
- clock divider fixes for OMAP-l138 LCDK board
rcar-du:
- R8A77965 support
- dma-buf fences fixes
- hardware indexed crtc/du group handling
- generic zplane property support
atmel-hclcdc:
- generic zplane property support
mediatek:
- use generic video mode function
exynos:
- S5PV210 FIMD variant support
- IPP v2 framework
- more HW overlays support"
* tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm: (1286 commits)
drm/amdgpu: fix 32-bit build warning
drm/exynos: fimc: signedness bug in fimc_setup_clocks()
drm/exynos: scaler: fix static checker warning
drm/amdgpu: Use dev_info() to report amdkfd is not supported for this ASIC
drm/amd/display: Remove use of division operator for long longs
drm/amdgpu: Update GFX info structure to match what vega20 used
drm/amdgpu/pp: remove duplicate assignment
drm/sched: add rcu_barrier after entity fini
drm/amdgpu: move VM BOs on LRU again
drm/amdgpu: consistenly use VM moved flag
drm/amdgpu: kmap PDs/PTs in amdgpu_vm_update_directories
drm/amdgpu: further optimize amdgpu_vm_handle_moved
drm/amdgpu: cleanup amdgpu_vm_validate_pt_bos v2
drm/amdgpu: rework VM state machine lock handling v2
drm/amdgpu: Add runtime VCN PG support
drm/amdgpu: Enable VCN static PG by default on RV
drm/amdgpu: Add VCN static PG support on RV
drm/amdgpu: Enable VCN CG by default on RV
drm/amdgpu: Add static CG control for VCN on RV
drm/exynos: Fix default value for zpos plane property
...
|
|
The dw_hdmi_setup_rx_sense exported function should not use struct device
to recover the dw-hdmi context using drvdata, but take struct dw_hdmi
directly like other exported functions.
This caused a regression using Meson DRM on S905X since v4.17-rc1 :
Internal error: Oops: 96000007 [#1] PREEMPT SMP
[...]
CPU: 0 PID: 124 Comm: irq/32-dw_hdmi_ Not tainted 4.17.0-rc7 #2
Hardware name: Libre Technology CC (DT)
[...]
pc : osq_lock+0x54/0x188
lr : __mutex_lock.isra.0+0x74/0x530
[...]
Process irq/32-dw_hdmi_ (pid: 124, stack limit = 0x00000000adf418cb)
Call trace:
osq_lock+0x54/0x188
__mutex_lock_slowpath+0x10/0x18
mutex_lock+0x30/0x38
__dw_hdmi_setup_rx_sense+0x28/0x98
dw_hdmi_setup_rx_sense+0x10/0x18
dw_hdmi_top_thread_irq+0x2c/0x50
irq_thread_fn+0x28/0x68
irq_thread+0x10c/0x1a0
kthread+0x128/0x130
ret_from_fork+0x10/0x18
Code: 34000964 d00050a2 51000484 9135c042 (f864d844)
---[ end trace 945641e1fbbc07da ]---
note: irq/32-dw_hdmi_[124] exited with preempt_count 1
genirq: exiting task "irq/32-dw_hdmi_" (124) is an active IRQ thread (irq 32)
Fixes: eea034af90c6 ("drm/bridge/synopsys: dw-hdmi: don't clobber drvdata")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1527673438-20643-1-git-send-email-narmstrong@baylibre.com
|
|
Building the driver in a configuration with !PM currently causes a
warning about these operations being unused. Mark them as such to shut
up the compiler.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426135853.30895-1-thierry.reding@gmail.com
|
|
Need to backmerge some nouveau fixes to reduce
the nouveau -next conflicts a lot.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.18:
UAPI Changes:
- Fix render node number regression from control node removal.
Driver Changes:
- Small header fix for virgl, used by qemu.
- Use vm_fault_t in qxl.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Tue 15 May 2018 06:16:03 PM AEST
# gpg: using RSA key FE558C72A67013C3
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/e63306b9-67a0-74ab-8883-08b3d9db72d2@mblankhorst.nl
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
- Add S5PV210 FIMD variant support.
- Add IPP v2 framework.
. it is a rewritten version of the Exynos mem-to-mem image processing
framework which supprts color space conversion, image up/down-scaling
and rotation. This new version replaces existing userspace API with
new easy-to-use and simple ones so we have already applied the use of
these API to real user, Tizen Platform[1], and also makes existing
Scaler, FIMC, GScaler and Rotator drivers to use IPP v2 core API.
And below are patch lists we have applied to a real user,
https://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/log/?h=tizen&qt=grep&q=ipp
https://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/commit/?h=tizen&id=b59be207365d10efd489e6f71c8a045b558c44fe
https://git.tizen.org/cgit/platform/kernel/linux-exynos/log/?h=tizen&qt=grep&q=ipp
TDM(Tizen Display Manager) is a Display HAL for Tizen platform.
Ps. Only real user using IPP API is Tizen.
[1] https://www.tizen.org/
- Two cleanups
. One is to just remove mode_set callback from MIPI-DSI driver
because drm_display_mode data is already available from crtc
atomic state.
. And other is to just use new return type, vm_fault_t
for page fault handler.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Mon 14 May 2018 14:23:53 AEST
# gpg: using RSA key 573834890C4312B8
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/1526276453-29879-1-git-send-email-inki.dae@samsung.com
|
|
drm-misc-next is still based on v4.16-rc7, and was getting a bit stale.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
|
|
The driver can work with or without extcon framework, but if extcon is
build as module, sii8620 should be build as module as well.
Fixes: 688838442147 ("drm/bridge/sii8620: use micro-USB cable detection logic to detect MHL")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180409062708.4326-1-a.hajda@samsung.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
|
|
adv7511_probe() is never called in atomic context.
This function is only set as ".probe" in struct i2c_driver.
Despite never getting called from atomic context, adv7511_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1523435622-4329-1-git-send-email-baijiaju1990@gmail.com
|
|
Could perhaps prevent some confusion.
Signed-off-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426213644.29318-1-peda@axentia.se
|
|
edid should be freed once it's finished being used.
Fixes: 56fe8b6f4991 ("drm/bridge: Add RGB to VGA bridge support")
Cc: Rob Herring <robh@kernel.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # v4.9+
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180420190007.1572-1-seanpaul@chromium.org
|
