| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 0a1db19f66c0960eb00e1f2ccd40708b6747f5b1 upstream.
The second argument to dev_err_probe() is the error value. Pass the
return value of devm_request_threaded_irq() there instead of the irq
number.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fixes: c47f7ff0fe61 ("gpio: pca953x: Utilise dev_err_probe() where it makes sense")
Link: https://lore.kernel.org/r/20250616134503.1201138-1-s.hauer@pengutronix.de
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 014a17deb41201449f76df2b20c857a9c3294a7c ]
GPIO drivers with latch input support may miss short pulses on input
pins even when input latching is enabled. The generic interrupt logic in
the pca953x driver reports interrupts by comparing the current input
value against the previously sampled one and only signals an event when
a level change is observed between two reads.
For short pulses, the first edge is captured when the input register is
read, but if the signal returns to its previous level before the read,
the second edge is not observed. As a result, successive pulses can
produce identical input values at read time and no level change is
detected, causing interrupts to be missed. Below timing diagram shows
this situation where the top signal is the input pin level and the
bottom signal indicates the latched value.
─────┐ ┌──*───────────────┐ ┌──*─────────────────┐ ┌──*───
│ │ . │ │ . │ │ .
│ │ │ │ │ │ │ │ │
└──*──┘ │ └──*──┘ │ └──*──┘ │
Input │ │ │ │ │ │
▼ │ ▼ │ ▼ │
IRQ │ IRQ │ IRQ │
. . .
─────┐ .┌──────────────┐ .┌────────────────┐ .┌──
│ │ │ │ │ │
│ │ │ │ │ │
└────────*┘ └────────*┘ └────────*┘
Latched │ │ │
▼ ▼ ▼
READ 0 READ 0 READ 0
NO CHANGE NO CHANGE
PCAL variants provide an interrupt status register that records which
pins triggered an interrupt, but the status and input registers cannot
be read atomically. The interrupt status is only cleared when the input
port is read, and the input value must also be read to determine the
triggering edge. If another interrupt occurs on a different line after
the status register has been read but before the input register is
sampled, that event will not be reflected in the earlier status
snapshot, so relying solely on the interrupt status register is also
insufficient.
Support for input latching and interrupt status handling was previously
added by [1], but the interrupt status-based logic was reverted by [2]
due to these issues. This patch addresses the original problem by
combining both sources of information. Events indicated by the interrupt
status register are merged with events detected through the existing
level-change logic. As a result:
* short pulses, whose second edges are invisible, are detected via the
interrupt status register, and
* interrupts that occur between the status and input reads are still
caught by the generic level-change logic.
This significantly improves robustness on devices that signal interrupts
as short pulses, while avoiding the issues that led to the earlier
reversion. In practice, even if only the first edge of a pulse is
observable, the interrupt is reliably detected.
This fixes missed interrupts from an Ilitek touch controller with its
interrupt line connected to a PCAL6416A, where active-low pulses are
approximately 200 us long.
[1] commit 44896beae605 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2")
[2] commit d6179f6c6204 ("gpio: pca953x: Improve interrupt support")
Fixes: d6179f6c6204 ("gpio: pca953x: Improve interrupt support")
Signed-off-by: Ernest Van Hoecke <ernest.vanhoecke@toradex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20251217153050.142057-1-ernestvanhoecke@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 417b0f8d08f878615de9481c6e8827fbc8b57ed2 ]
Adds support for level-triggered interrupts in the PCA953x GPIO
expander driver. Previously, the driver only supported edge-triggered
interrupts, which could lead to missed events in scenarios where an
interrupt condition persists until it is explicitly cleared.
By enabling level-triggered interrupts, the driver can now detect and
respond to sustained interrupt conditions more reliably.
Signed-off-by: Potin Lai <potin.lai.pt@gmail.com>
Link: https://lore.kernel.org/r/20250409-gpio-pca953x-level-triggered-irq-v3-1-7f184d814934@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 014a17deb412 ("gpio: pca953x: handle short interrupt pulses on PCAL devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6811886ac91eb414b1b74920e05e6590c3f2a688 ]
We have a temporary variable to keep pointer to struct device.
Utilise it where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 014a17deb412 ("gpio: pca953x: handle short interrupt pulses on PCAL devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c47f7ff0fe61738a40b1b4fef3cd8317ec314079 ]
At least in pca953x_irq_setup() we may use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 014a17deb412 ("gpio: pca953x: handle short interrupt pulses on PCAL devices")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 20cf2aed89ac6d78a0122e31c875228e15247194 upstream.
The GPIO controller is configured as non-sleeping but it uses generic
pinctrl helpers which use a mutex for synchronization.
This can cause the following lockdep splat with shared GPIOs enabled on
boards which have multiple devices using the same GPIO:
BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:591
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 12, name:
kworker/u16:0
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
6 locks held by kworker/u16:0/12:
#0: ffff0001f0018d48 ((wq_completion)events_unbound#2){+.+.}-{0:0},
at: process_one_work+0x18c/0x604
#1: ffff8000842dbdf0 (deferred_probe_work){+.+.}-{0:0}, at:
process_one_work+0x1b4/0x604
#2: ffff0001f18498f8 (&dev->mutex){....}-{4:4}, at:
__device_attach+0x38/0x1b0
#3: ffff0001f75f1e90 (&gdev->srcu){.+.?}-{0:0}, at:
gpiod_direction_output_raw_commit+0x0/0x360
#4: ffff0001f46e3db8 (&shared_desc->spinlock){....}-{3:3}, at:
gpio_shared_proxy_direction_output+0xd0/0x144 [gpio_shared_proxy]
#5: ffff0001f180ee90 (&gdev->srcu){.+.?}-{0:0}, at:
gpiod_direction_output_raw_commit+0x0/0x360
irq event stamp: 81450
hardirqs last enabled at (81449): [<ffff8000813acba4>]
_raw_spin_unlock_irqrestore+0x74/0x78
hardirqs last disabled at (81450): [<ffff8000813abfb8>]
_raw_spin_lock_irqsave+0x84/0x88
softirqs last enabled at (79616): [<ffff8000811455fc>]
__alloc_skb+0x17c/0x1e8
softirqs last disabled at (79614): [<ffff8000811455fc>]
__alloc_skb+0x17c/0x1e8
CPU: 2 UID: 0 PID: 12 Comm: kworker/u16:0 Not tainted
6.19.0-rc4-next-20260105+ #11975 PREEMPT
Hardware name: Hardkernel ODROID-M1 (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x90/0xd0
dump_stack+0x18/0x24
__might_resched+0x144/0x248
__might_sleep+0x48/0x98
__mutex_lock+0x5c/0x894
mutex_lock_nested+0x24/0x30
pinctrl_get_device_gpio_range+0x44/0x128
pinctrl_gpio_direction+0x3c/0xe0
pinctrl_gpio_direction_output+0x14/0x20
rockchip_gpio_direction_output+0xb8/0x19c
gpiochip_direction_output+0x38/0x94
gpiod_direction_output_raw_commit+0x1d8/0x360
gpiod_direction_output_nonotify+0x7c/0x230
gpiod_direction_output+0x34/0xf8
gpio_shared_proxy_direction_output+0xec/0x144 [gpio_shared_proxy]
gpiochip_direction_output+0x38/0x94
gpiod_direction_output_raw_commit+0x1d8/0x360
gpiod_direction_output_nonotify+0x7c/0x230
gpiod_configure_flags+0xbc/0x480
gpiod_find_and_request+0x1a0/0x574
gpiod_get_index+0x58/0x84
devm_gpiod_get_index+0x20/0xb4
devm_gpiod_get_optional+0x18/0x30
rockchip_pcie_probe+0x98/0x380
platform_probe+0x5c/0xac
really_probe+0xbc/0x298
Fixes: 936ee2675eee ("gpio/rockchip: add driver for rockchip gpio")
Cc: stable@vger.kernel.org
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/d035fc29-3b03-4cd6-b8ec-001f93540bc6@samsung.com/
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20260106090011.21603-1-bartosz.golaszewski@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d967310c49ed93ac11cef408a55ddf15c3dd52e ]
Dell Precision 7780 often wakes up on its own from suspend. Sometimes
wake up happens immediately (i. e. within 7 seconds), sometimes it happens
after, say, 30 minutes.
Fixes: 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
Link: https://lore.kernel.org/linux-i2c/197ae95ffd8.dc819e60457077.7692120488609091556@zohomail.com/
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Askar Safin <safinaskar@gmail.com>
Link: https://lore.kernel.org/r/20251206180414.3183334-2-safinaskar@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
[ adapted quirk entry location from gpiolib-acpi-quirks.c to gpiolib-acpi.c ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 52721cfc78c76b09c66e092b52617006390ae96a upstream.
Call gpiochip_remove() to free the resources allocated by
gpiochip_add_data() in error path.
Fixes: 553b75d4bfe9 ("gpio: regmap: Allow to allocate regmap-irq device")
Fixes: ae495810cffe ("gpio: regmap: add the .fixed_direction_output configuration parameter")
CC: stable@vger.kernel.org
Co-developed-by: WangYuli <wangyl5933@chinaunicom.cn>
Signed-off-by: WangYuli <wangyl5933@chinaunicom.cn>
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20251204101303.30353-1-guanwentao@uniontech.com
[Bartosz: reworked the commit message]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2ba5772e530f73eb847fb96ce6c4017894869552 ]
The direction of the IDIO-16 GPIO lines is fixed with the first 16 lines
as output and the remaining 16 lines as input. Set the gpio_config
fixed_direction_output member to represent the fixed direction of the
GPIO lines.
Fixes: db02247827ef ("gpio: idio-16: Migrate to the regmap API")
Reported-by: Mark Cave-Ayland <mark.caveayland@nutanix.com>
Closes: https://lore.kernel.org/r/9b0375fd-235f-4ee1-a7fa-daca296ef6bf@nutanix.com
Suggested-by: Michael Walle <mwalle@kernel.org>
Cc: stable@vger.kernel.org # ae495810cffe: gpio: regmap: add the .fixed_direction_output configuration parameter
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251020-fix-gpio-idio-16-regmap-v2-3-ebeb50e93c33@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 00aaae60faf554c27c95e93d47f200a93ff266ef ]
There are GPIO controllers such as the one present in the LX2160ARDB
QIXIS FPGA which have fixed-direction input and output GPIO lines mixed
together in a single register. This cannot be modeled using the
gpio-regmap as-is since there is no way to present the true direction of
a GPIO line.
In order to make this use case possible, add a new configuration
parameter - fixed_direction_output - into the gpio_regmap_config
structure. This will enable user drivers to provide a bitmap that
represents the fixed direction of the GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 2ba5772e530f ("gpio: idio-16: Define fixed direction of the GPIO lines")
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 553b75d4bfe9264f631d459fe9996744e0672b0e ]
GPIO controller often have support for IRQ: allow to easily allocate
both gpio-regmap and regmap-irq in one operation.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Mathieu Dubois-Briand <mathieu.dubois-briand@bootlin.com>
Link: https://lore.kernel.org/r/20250824-mdb-max7360-support-v14-5-435cfda2b1ea@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
Stable-dep-of: 2ba5772e530f ("gpio: idio-16: Define fixed direction of the GPIO lines")
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3396995f9fb6bcbe0004a68118a22f98bab6e2b9 upstream.
With the new __counted_by annocation in ljca_gpio_packet, the "num"
struct member must be set before accessing the "item" array. Failing to
do so will trigger a runtime warning when enabling CONFIG_UBSAN_BOUNDS
and CONFIG_FORTIFY_SOURCE.
Fixes: 1034cc423f1b ("gpio: update Intel LJCA USB GPIO driver")
Cc: stable@vger.kernel.org
Signed-off-by: Haoyu Li <lihaoyu499@gmail.com>
Link: https://lore.kernel.org/stable/20241203141451.342316-1-lihaoyu499%40gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4c4e6ea4a120cc5ab58e437c6ba123cbfc357d45 ]
The generic_handle_domain_irq() function resolves the hardware IRQ
internally. The driver performed a duplicative mapping by calling
irq_find_mapping() first, which could lead to an RCU stall.
Delete the redundant irq_find_mapping() call and pass the hardware IRQ
directly to generic_handle_domain_irq().
Fixes: c5a4b6fd31e8 ("gpio: Add support for Intel LJCA USB GPIO driver")
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20251023070231.1305-1-vulab@iscas.ac.cn
[Bartosz: remove unused variable]
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1034cc423f1b4a7a9a56d310ca980fcd2753e11d ]
This driver communicate with LJCA GPIO module with specific
protocol through interfaces exported by LJCA USB driver.
Update the driver according to LJCA USB driver's changes.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/1696833205-16716-5-git-send-email-wentong.wu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 4c4e6ea4a120 ("gpio: ljca: Fix duplicated IRQ mapping")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c4d35e635f3a65aec291a6045cae8c99cede5bba upstream.
Attempting to load the 104-idio-16 module fails during regmap
initialization with a return error -EINVAL. This is a result of the
regmap cache failing initialization. Set the idio_16_regmap_config
max_register member to fix this failure.
Fixes: 2c210c9a34a3 ("gpio: 104-idio-16: Migrate to the regmap API")
Reported-by: Mark Cave-Ayland <mark.caveayland@nutanix.com>
Closes: https://lore.kernel.org/r/9b0375fd-235f-4ee1-a7fa-daca296ef6bf@nutanix.com
Suggested-by: Mark Cave-Ayland <mark.caveayland@nutanix.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251020-fix-gpio-idio-16-regmap-v2-1-ebeb50e93c33@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d37623132a6347b4ab9e2179eb3f2fa77863c364 upstream.
Attempting to load the pci-idio-16 module fails during regmap
initialization with a return error -EINVAL. This is a result of the
regmap cache failing initialization. Set the idio_16_regmap_config
max_register member to fix this failure.
Fixes: 73d8f3efc5c2 ("gpio: pci-idio-16: Migrate to the regmap API")
Reported-by: Mark Cave-Ayland <mark.caveayland@nutanix.com>
Closes: https://lore.kernel.org/r/9b0375fd-235f-4ee1-a7fa-daca296ef6bf@nutanix.com
Suggested-by: Mark Cave-Ayland <mark.caveayland@nutanix.com>
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: William Breathitt Gray <wbg@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20251020-fix-gpio-idio-16-regmap-v2-2-ebeb50e93c33@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b5f8aa8d4bde0cf3e4595af5a536da337e5f1c78 ]
The slimbus regmap passed to the GPIO driver down from MFD does not use
fast_io. This means a mutex is used for locking and thus this GPIO chip
must not be used in atomic context. Change the can_sleep switch in
struct gpio_chip to true.
Fixes: 59c324683400 ("gpio: wcd934x: Add support to wcd934x gpio controller")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c6ccc4dde17676dfe617b9a37bd9ba19a8fc87ee ]
When a software-node gets added to a device which already has another
fwnode as primary node it will become the secondary fwnode for that
device.
Currently if a software-node with GPIO properties ends up as the secondary
fwnode then gpiod_find_by_fwnode() will fail to find the GPIOs.
Add a new gpiod_fwnode_lookup() helper which falls back to calling
gpiod_find_by_fwnode() with the secondary fwnode if the GPIO was not
found in the primary fwnode.
Fixes: e7f9ff5dc90c ("gpiolib: add support for software nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20250920200955.20403-1-hansg@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a0b2a6bbff8c26aafdecd320f38f52c341d5cafa ]
regmap_update_bits() can fail, check its return value like we do
elsewhere in the driver.
Link: https://lore.kernel.org/r/20250707-gpiochip-set-rv-gpio-round4-v1-2-35668aaaf6d2@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ff0f0d7c6587e38c308be9905e36f86e98fb9c1f ]
regmap_update_bits() can fail so check its return value in
wcd_gpio_direction_output() for consistency with the rest of the code
and propagate any errors.
Link: https://lore.kernel.org/r/20250709-gpiochip-set-rv-gpio-remaining-v1-2-b8950f69618d@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 810bd9066fb1871b8a9528f31f2fdbf2a8b73bf2 upstream.
The gpio-mlxbf3 driver interfaces with two GPIO controllers,
device instance 0 and 1. There is a single IRQ resource shared
between the two controllers, and it is found in the ACPI table for
device instance 0. The driver should not use platform_get_irq(),
otherwise this error is logged when probing instance 1:
mlxbf3_gpio MLNXBF33:01: error -ENXIO: IRQ index 0 not found
Cc: stable@vger.kernel.org
Fixes: cd33f216d241 ("gpio: mlxbf3: Add gpio driver support")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/ce70b98a201ce82b9df9aa80ac7a5eeaa2268e52.1754928650.git.davthompson@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 56bdf7270ff4f870e2d4bfacdc00161e766dba2d upstream.
This reverts commit 10af0273a35ab4513ca1546644b8c853044da134.
While this change was merged, it is not the preferred solution.
During review of a similar change to the gpio-mlxbf2 driver, the
use of "platform_get_irq_optional" was identified as the preferred
solution, so let's use it for gpio-mlxbf3 driver as well.
Cc: stable@vger.kernel.org
Fixes: 10af0273a35a ("gpio: mlxbf3: only get IRQ for device instance 0")
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/8d2b630c71b3742f2c74242cf7d602706a6108e6.1754928650.git.davthompson@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63c7bc53a35e785accdc2ceab8f72d94501931ab upstream.
The gpio-mlxbf2 driver interfaces with four GPIO controllers,
device instances 0-3. There are two IRQ resources shared between
the four controllers, and they are found in the ACPI table for
instances 0 and 3. The driver should not use platform_get_irq(),
otherwise this error is logged when probing instances 1 and 2:
mlxbf2_gpio MLNXBF22:01: error -ENXIO: IRQ index 0 not found
Fixes: 2b725265cb08 ("gpio: mlxbf2: Introduce IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20250728144619.29894-1-davthompson@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4740e1e2f320061c2f0dbadc0dd3dfb58df986d5 upstream.
Quote from the virtio specification chapter 4.2.2.2:
"For the device-specific configuration space, the driver MUST use 8 bit
wide accesses for 8 bit wide fields, 16 bit wide and aligned accesses
for 16 bit wide fields and 32 bit wide and aligned accesses for 32 and
64 bit wide fields."
Signed-off-by: Harald Mommer <harald.mommer@oss.qualcomm.com>
Cc: stable@vger.kernel.org
Fixes: 3a29355a22c0 ("gpio: Add virtio-gpio driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20250724143718.5442-2-harald.mommer@oss.qualcomm.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 10af0273a35ab4513ca1546644b8c853044da134 ]
The gpio-mlxbf3 driver interfaces with two GPIO controllers,
device instance 0 and 1. There is a single IRQ resource shared
between the two controllers, and it is found in the ACPI table for
device instance 0. The driver should not attempt to get an IRQ
resource when probing device instance 1, otherwise the following
error is logged:
mlxbf3_gpio MLNXBF33:01: error -ENXIO: IRQ index 0 not found
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Fixes: cd33f216d241 ("gpio: mlxbf3: Add gpio driver support")
Link: https://lore.kernel.org/r/20250613163443.1065217-1-davthompson@nvidia.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4e310626eb4df52a31a142c1360fead0fcbd3793 ]
This is prepare patch for switching s5m8767 regulator driver to
use GPIO descriptor. DTS for exynos5250 spring incorrectly specifies
"active low" polarity for the DVS and DS line. But per datasheet,
they are actually active high. So add polarity quirk for it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250327004945.563765-1-peng.fan@oss.nxp.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3e38f946062b4845961ab86b726651b4457b2af8 ]
If an input changes state during wake-up and is used as an interrupt
source, the IRQ handler reads the volatile input register to clear the
interrupt mask and deassert the IRQ line. However, the IRQ handler is
triggered before access to the register is granted, causing the read
operation to fail.
As a result, the IRQ handler enters a loop, repeatedly printing the
"failed reading register" message, until `pca953x_resume()` is eventually
called, which restores the driver context and enables access to
registers.
Fix by disabling the IRQ line before entering suspend mode, and
re-enabling it after the driver context is restored in `pca953x_resume()`.
An IRQ can be disabled with disable_irq() and still wake the system as
long as the IRQ has wake enabled, so the wake-up functionality is
preserved.
Fixes: b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Cc: stable@vger.kernel.org
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250512095441.31645-1-francesco@dolcini.it
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8e471b784a720f6f34f9fb449ba0744359dcaccb ]
Use macros defined in linux/cleanup.h to automate resource lifetime
control in gpio-pca953x.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 3e38f946062b ("gpio: pca953x: fix IRQ storm on system wake up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec5bde62019b0a5300c67bd81b9864a8ea12274e ]
Split regcache handling to the respective helpers. It will allow to
have further refactoring with ease.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 3e38f946062b ("gpio: pca953x: fix IRQ storm on system wake up")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b8c7a1ac884cc267d1031f8de07f1a689a69fbab ]
The regulator comment in of_gpio_set_polarity_by_property()
made on top of a couple of the cases, while Atmel HSMCI quirk
is not related to that. Make it clear by moving Atmel HSMCI
quirk up out of the scope of the regulator comment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250402122058.1517393-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c5672e310ad971d408752fce7596ed27adc6008f upstream.
Device can be unbound, so driver must also release memory for the wakeup
source.
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250406202245.53854-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8323f3a69de6f6e96bf22f32dd8e2920766050c2 upstream.
When the Tegra186 GPIO controller is probed through ACPI matching,
the driver emits two error messages during probing:
"tegra186-gpio NVDA0508:00: invalid resource (null)"
"tegra186-gpio NVDA0508:00: invalid resource (null)"
Fix this by getting resource first and then do the ioremap.
Fixes: 2606e7c9f5fc ("gpio: tegra186: Add ACPI support")
Cc: stable@vger.kernel.org
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250327032349.78809-1-kanie@linux.alibaba.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 391b41f983bf7ff853de44704d8e14e7cc648a9b ]
of_parse_phandle_with_fixed_args() requires its caller to
call into of_node_put() on the node pointer from the output
structure, but such a call is currently missing.
Call into of_node_put() to rectify that.
Fixes: 159f8a0209af ("gpio-rcar: Add DT support")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250305163753.34913-2-fabrizio.castro.jz@renesas.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 12f65d1203507f7db3ba59930fe29a3b8eee9945 upstream.
Both new_device_store and delete_device_store touch module global
resources (e.g. gpio_aggregator_lock). To prevent race conditions with
module unload, a reference needs to be held.
Add try_module_get() in these handlers.
For new_device_store, this eliminates what appears to be the most dangerous
scenario: if an id is allocated from gpio_aggregator_idr but
platform_device_register has not yet been called or completed, a concurrent
module unload could fail to unregister/delete the device, leaving behind a
dangling platform device/GPIO forwarder. This can result in various issues.
The following simple reproducer demonstrates these problems:
#!/bin/bash
while :; do
# note: whether 'gpiochip0 0' exists or not does not matter.
echo 'gpiochip0 0' > /sys/bus/platform/drivers/gpio-aggregator/new_device
done &
while :; do
modprobe gpio-aggregator
modprobe -r gpio-aggregator
done &
wait
Starting with the following warning, several kinds of warnings will appear
and the system may become unstable:
------------[ cut here ]------------
list_del corruption, ffff888103e2e980->next is LIST_POISON1 (dead000000000100)
WARNING: CPU: 1 PID: 1327 at lib/list_debug.c:56 __list_del_entry_valid_or_report+0xa3/0x120
[...]
RIP: 0010:__list_del_entry_valid_or_report+0xa3/0x120
[...]
Call Trace:
<TASK>
? __list_del_entry_valid_or_report+0xa3/0x120
? __warn.cold+0x93/0xf2
? __list_del_entry_valid_or_report+0xa3/0x120
? report_bug+0xe6/0x170
? __irq_work_queue_local+0x39/0xe0
? handle_bug+0x58/0x90
? exc_invalid_op+0x13/0x60
? asm_exc_invalid_op+0x16/0x20
? __list_del_entry_valid_or_report+0xa3/0x120
gpiod_remove_lookup_table+0x22/0x60
new_device_store+0x315/0x350 [gpio_aggregator]
kernfs_fop_write_iter+0x137/0x1f0
vfs_write+0x262/0x430
ksys_write+0x60/0xd0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: 828546e24280 ("gpio: Add GPIO Aggregator")
Cc: stable@vger.kernel.org
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Link: https://lore.kernel.org/r/20250224143134.3024598-2-koichiro.den@canonical.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f02c41f87cfe61440c18bf77d1ef0a884b9ee2b5 upstream.
Use raw_spinlock in order to fix spurious messages about invalid context
when spinlock debugging is enabled. The lock is only used to serialize
register access.
[ 4.239592] =============================
[ 4.239595] [ BUG: Invalid wait context ]
[ 4.239599] 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 Not tainted
[ 4.239603] -----------------------------
[ 4.239606] kworker/u8:5/76 is trying to lock:
[ 4.239609] ffff0000091898a0 (&p->lock){....}-{3:3}, at: gpio_rcar_config_interrupt_input_mode+0x34/0x164
[ 4.239641] other info that might help us debug this:
[ 4.239643] context-{5:5}
[ 4.239646] 5 locks held by kworker/u8:5/76:
[ 4.239651] #0: ffff0000080fb148 ((wq_completion)async){+.+.}-{0:0}, at: process_one_work+0x190/0x62c
[ 4.250180] OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value.
[ 4.254094] #1: ffff80008299bd80 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x1b8/0x62c
[ 4.254109] #2: ffff00000920c8f8
[ 4.258345] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'bitclock-master' with a value.
[ 4.264803] (&dev->mutex){....}-{4:4}, at: __device_attach_async_helper+0x3c/0xdc
[ 4.264820] #3: ffff00000a50ca40 (request_class#2){+.+.}-{4:4}, at: __setup_irq+0xa0/0x690
[ 4.264840] #4:
[ 4.268872] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'frame-master' with a value.
[ 4.273275] ffff00000a50c8c8 (lock_class){....}-{2:2}, at: __setup_irq+0xc4/0x690
[ 4.296130] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz
[ 4.304082] stack backtrace:
[ 4.304086] CPU: 1 UID: 0 PID: 76 Comm: kworker/u8:5 Not tainted 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35
[ 4.304092] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 4.304097] Workqueue: async async_run_entry_fn
[ 4.304106] Call trace:
[ 4.304110] show_stack+0x14/0x20 (C)
[ 4.304122] dump_stack_lvl+0x6c/0x90
[ 4.304131] dump_stack+0x14/0x1c
[ 4.304138] __lock_acquire+0xdfc/0x1584
[ 4.426274] lock_acquire+0x1c4/0x33c
[ 4.429942] _raw_spin_lock_irqsave+0x5c/0x80
[ 4.434307] gpio_rcar_config_interrupt_input_mode+0x34/0x164
[ 4.440061] gpio_rcar_irq_set_type+0xd4/0xd8
[ 4.444422] __irq_set_trigger+0x5c/0x178
[ 4.448435] __setup_irq+0x2e4/0x690
[ 4.452012] request_threaded_irq+0xc4/0x190
[ 4.456285] devm_request_threaded_irq+0x7c/0xf4
[ 4.459398] ata1: link resume succeeded after 1 retries
[ 4.460902] mmc_gpiod_request_cd_irq+0x68/0xe0
[ 4.470660] mmc_start_host+0x50/0xac
[ 4.474327] mmc_add_host+0x80/0xe4
[ 4.477817] tmio_mmc_host_probe+0x2b0/0x440
[ 4.482094] renesas_sdhi_probe+0x488/0x6f4
[ 4.486281] renesas_sdhi_internal_dmac_probe+0x60/0x78
[ 4.491509] platform_probe+0x64/0xd8
[ 4.495178] really_probe+0xb8/0x2a8
[ 4.498756] __driver_probe_device+0x74/0x118
[ 4.503116] driver_probe_device+0x3c/0x154
[ 4.507303] __device_attach_driver+0xd4/0x160
[ 4.511750] bus_for_each_drv+0x84/0xe0
[ 4.515588] __device_attach_async_helper+0xb0/0xdc
[ 4.520470] async_run_entry_fn+0x30/0xd8
[ 4.524481] process_one_work+0x210/0x62c
[ 4.528494] worker_thread+0x1ac/0x340
[ 4.532245] kthread+0x10c/0x110
[ 4.535476] ret_from_fork+0x10/0x20
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250121135833.3769310-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9644fbfbcab13da7f8b37bef7c51e5b8407d031 upstream.
The stmpe_reg_read function can fail, but its return value is not checked
in stmpe_gpio_irq_sync_unlock. This can lead to silent failures and
incorrect behavior if the hardware access fails.
This patch adds checks for the return value of stmpe_reg_read. If the
function fails, an error message is logged and the function returns
early to avoid further issues.
Fixes: b888fb6f2a27 ("gpio: stmpe: i2c transfer are forbiden in atomic context")
Cc: stable@vger.kernel.org # 4.16+
Signed-off-by: Wentao Liang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20250212021849.275-1-vulab@iscas.ac.cn
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8743d66979e494c5378563e6b5a32e913380abd8 upstream.
Spurious immediate wake up events are reported on Acer Nitro ANV14. GPIO 11 is
specified as an edge triggered input and also a wake source but this pin is
supposed to be an output pin for an LED, so it's effectively floating.
Block the interrupt from getting set up for this GPIO on this device.
Cc: stable@vger.kernel.org
Reported-by: Delgan <delgan.py@gmail.com>
Tested-by: Delgan <delgan.py@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3954
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Mika Westerberg <westeri@kernel.org>
Link: https://lore.kernel.org/r/20250211203222.761206-1-superm1@kernel.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7b4aebeecbbd5b5fe73e35fad3f62ed21aa7ef44 ]
The gpiochip_get_ngpios() uses chip_*() macros to print messages.
However these macros rely on gpiodev to be initialised and set,
which is not the case when called via bgpio_init(). In such a case
the printing messages will crash on NULL pointer dereference.
Replace chip_*() macros by the respective dev_*() ones to avoid
such crash.
Fixes: 55b2395e4e92 ("gpio: mmio: handle "ngpios" properly in bgpio_init()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250213155646.2882324-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 615279db222c3ac56d5c93716efd72b843295c1f ]
Add a missing newline to the format string of the "Couldn't get IRQ
for bank..." error message.
Fixes: 757651e3d60e ("gpio: bcm281xx: Add GPIO driver")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-3-409135eab780@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 57f5db77a915cc29461a679a6bcae7097967be1a ]
The settings for all GPIOs are locked by default in bcm_kona_gpio_reset.
The settings for a GPIO are unlocked when requesting it as a GPIO, but
not when requesting it as an interrupt, causing the IRQ settings to not
get applied.
Fix this by making sure to unlock the right bits when an IRQ is requested.
To avoid a situation where an IRQ being released causes a lock despite
the same GPIO being used by a GPIO request or vice versa, add an unlock
counter and only lock if it reaches 0.
Fixes: 757651e3d60e ("gpio: bcm281xx: Add GPIO driver")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-2-409135eab780@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de1d0d160f64ee76df1d364d521b2faf465a091c ]
The GPIO lock/unlock functions clear/write a bit to the relevant
register for each bank. However, due to an oversight the bit that
was being written was based on the total GPIO number, not the index
of the GPIO within the relevant bank, causing it to fail for any
GPIO above 32 (thus any GPIO for banks above bank 0).
Fix lock/unlock for these banks by using the correct bit.
Fixes: bdb93c03c550 ("gpio: bcm281xx: Centralize register locking")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-1-409135eab780@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d6179f6c6204f9932aed3a7a2100b4a295dfed9d ]
The GPIO drivers with latch interrupt support (typically types starting
with PCAL) have interrupt status registers to determine which particular
inputs have caused an interrupt. Unfortunately there is no atomic
operation to read these registers and clear the interrupt. Clearing the
interrupt is done by reading the input registers.
The code was reading the interrupt status registers, and then reading
the input registers. If an input changed between these two events it was
lost.
The solution in this patch is to revert to the non-latch version of
code, i.e. remembering the previous input status, and looking for the
changes. This system results in no more I2C transfers, so is no slower.
The latch property of the device still means interrupts will still be
noticed if the input changes back to its initial state.
Fixes: 44896beae605 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2")
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240606033102.2271916-1-mark.tomlinson@alliedtelesis.co.nz
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b049e7abe9001a780d58e78e3833dcceee22f396 ]
struct platform_device::id was only set by board code, but since i.MX
became a devicetree-only platform, this will always be -1
(PLATFORM_DEVID_NONE).
Note: of_alias_get_id() returns a negative number on error and base
treats all negative errors the same, so we need not add any additional
error handling.
Fixes: 0f2c7af45d7e ("gpio: mxc: Convert the driver to DT-only")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20250113-b4-imx-gpio-base-warning-v1-3-0a28731a5cf6@pengutronix.de
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7cef813a91c468253c80633891393478b9f2c966 ]
When the dirver fails getting this GPIO, it fails silently. Log an error
message to make debugging a lot easier by just reading dmesg.
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Fixes: 054ccdef8b28 ("gpio: pca953x: Add optional reset gpio control")
Link: https://lore.kernel.org/r/20241219-pca953x-log-no-reset-gpio-v1-1-9aa7bcc45ead@bootlin.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 53c59d66c44c5eb98b34da9967f937e5387f8624 ]
Curtrently the error path is unsynchronised with removal due to
regulator being disabled before other device managed resources
are handled. Correct that by wrapping regulator enablement in
the respective call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 7cef813a91c4 ("gpio: pca953x: log an error when failing to get the reset GPIO")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2f4d3e293392571e02b106c8b431b638bd029276 ]
New code should solely use firmware nodes for the specifics and
not any callbacks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 7cef813a91c4 ("gpio: pca953x: log an error when failing to get the reset GPIO")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9722c3b66e21ff08aec570d02a97d331087fd70f ]
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Stable-dep-of: 28fa3291cad1 ("clk: fix an OF node reference leak in of_clk_get_parent_name()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9860370c2172704b6b4f0075a0c2a29fd84af96a upstream.
irq_chip functions may be called in raw spinlock context. Therefore, we
must also use a raw spinlock for our own internal locking.
This fixes the following lockdep splat:
[ 5.349336] =============================
[ 5.353349] [ BUG: Invalid wait context ]
[ 5.357361] 6.13.0-rc5+ #69 Tainted: G W
[ 5.363031] -----------------------------
[ 5.367045] kworker/u17:1/44 is trying to lock:
[ 5.371587] ffffff88018b02c0 (&chip->gpio_lock){....}-{3:3}, at: xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8))
[ 5.380079] other info that might help us debug this:
[ 5.385138] context-{5:5}
[ 5.387762] 5 locks held by kworker/u17:1/44:
[ 5.392123] #0: ffffff8800014958 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3204)
[ 5.402260] #1: ffffffc082fcbdd8 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3205)
[ 5.411528] #2: ffffff880172c900 (&dev->mutex){....}-{4:4}, at: __device_attach (drivers/base/dd.c:1006)
[ 5.419929] #3: ffffff88039c8268 (request_class#2){+.+.}-{4:4}, at: __setup_irq (kernel/irq/internals.h:156 kernel/irq/manage.c:1596)
[ 5.428331] #4: ffffff88039c80c8 (lock_class#2){....}-{2:2}, at: __setup_irq (kernel/irq/manage.c:1614)
[ 5.436472] stack backtrace:
[ 5.439359] CPU: 2 UID: 0 PID: 44 Comm: kworker/u17:1 Tainted: G W 6.13.0-rc5+ #69
[ 5.448690] Tainted: [W]=WARN
[ 5.451656] Hardware name: xlnx,zynqmp (DT)
[ 5.455845] Workqueue: events_unbound deferred_probe_work_func
[ 5.461699] Call trace:
[ 5.464147] show_stack+0x18/0x24 C
[ 5.467821] dump_stack_lvl (lib/dump_stack.c:123)
[ 5.471501] dump_stack (lib/dump_stack.c:130)
[ 5.474824] __lock_acquire (kernel/locking/lockdep.c:4828 kernel/locking/lockdep.c:4898 kernel/locking/lockdep.c:5176)
[ 5.478758] lock_acquire (arch/arm64/include/asm/percpu.h:40 kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851 kernel/locking/lockdep.c:5814)
[ 5.482429] _raw_spin_lock_irqsave (include/linux/spinlock_api_smp.h:111 kernel/locking/spinlock.c:162)
[ 5.486797] xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8))
[ 5.490737] irq_enable (kernel/irq/internals.h:236 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345)
[ 5.494060] __irq_startup (kernel/irq/internals.h:241 kernel/irq/chip.c:180 kernel/irq/chip.c:250)
[ 5.497645] irq_startup (kernel/irq/chip.c:270)
[ 5.501143] __setup_irq (kernel/irq/manage.c:1807)
[ 5.504728] request_threaded_irq (kernel/irq/manage.c:2208)
Fixes: a32c7caea292 ("gpio: gpio-xilinx: Add interrupt support")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250110163354.2012654-1-sean.anderson@linux.dev
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 050b23d081da0f29474de043e9538c1f7a351b3b ]
devm_kasprintf() can return a NULL pointer on failure,but this
returned value in grgpio_probe is not checked.
Add NULL check in grgpio_probe, to handle kernel NULL
pointer dereference error.
Cc: stable@vger.kernel.org
Fixes: 7eb6ce2f2723 ("gpio: Convert to using %pOF instead of full_name")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Link: https://lore.kernel.org/r/20241114091822.78199-1-hanchunchao@inspur.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d036ae41cebdfae92666024163c109b8fef516fa ]
Instead of dereferencing the platform device pointer repeatedly, just
store its address in a helper variable.
Link: https://lore.kernel.org/r/20241015131832.44678-3-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Stable-dep-of: 050b23d081da ("gpio: grgpio: Add NULL check in grgpio_probe")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
