summaryrefslogtreecommitdiff
path: root/drivers/gpio
AgeCommit message (Collapse)AuthorFilesLines
2025-10-29gpio: wcd934x: mark the GPIO controller as sleepingBartosz Golaszewski1-1/+1
[ Upstream commit b5f8aa8d4bde0cf3e4595af5a536da337e5f1c78 ] The slimbus regmap passed to the GPIO driver down from MFD does not use fast_io. This means a mutex is used for locking and thus this GPIO chip must not be used in atomic context. Change the can_sleep switch in struct gpio_chip to true. Fixes: 59c324683400 ("gpio: wcd934x: Add support to wcd934x gpio controller") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-10-29gpio: wcd934x: Remove duplicate assignment of of_gpio_n_cellsAndy Shevchenko1-1/+0
[ Upstream commit a060dc6620c13435b78e92cd2ebdbb6d11af237a ] The of_gpio_n_cells default is 2 when ->of_xlate() callback is not defined. No need to assign it explicitly in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Stable-dep-of: b5f8aa8d4bde ("gpio: wcd934x: mark the GPIO controller as sleeping") Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-09-09gpio: pca953x: fix IRQ storm on system wake upEmanuele Ghidoli1-0/+5
[ Upstream commit 3e38f946062b4845961ab86b726651b4457b2af8 ] If an input changes state during wake-up and is used as an interrupt source, the IRQ handler reads the volatile input register to clear the interrupt mask and deassert the IRQ line. However, the IRQ handler is triggered before access to the register is granted, causing the read operation to fail. As a result, the IRQ handler enters a loop, repeatedly printing the "failed reading register" message, until `pca953x_resume()` is eventually called, which restores the driver context and enables access to registers. Fix by disabling the IRQ line before entering suspend mode, and re-enabling it after the driver context is restored in `pca953x_resume()`. An IRQ can be disabled with disable_irq() and still wake the system as long as the IRQ has wake enabled, so the wake-up functionality is preserved. Fixes: b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle") Cc: stable@vger.kernel.org Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20250512095441.31645-1-francesco@dolcini.it Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> [ Apply directly to suspend/resume functions ] Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-08-28gpio: rcar: Use raw_spinlock to protect register accessNiklas Söderlund1-10/+10
commit f02c41f87cfe61440c18bf77d1ef0a884b9ee2b5 upstream. Use raw_spinlock in order to fix spurious messages about invalid context when spinlock debugging is enabled. The lock is only used to serialize register access. [ 4.239592] ============================= [ 4.239595] [ BUG: Invalid wait context ] [ 4.239599] 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 Not tainted [ 4.239603] ----------------------------- [ 4.239606] kworker/u8:5/76 is trying to lock: [ 4.239609] ffff0000091898a0 (&p->lock){....}-{3:3}, at: gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.239641] other info that might help us debug this: [ 4.239643] context-{5:5} [ 4.239646] 5 locks held by kworker/u8:5/76: [ 4.239651] #0: ffff0000080fb148 ((wq_completion)async){+.+.}-{0:0}, at: process_one_work+0x190/0x62c [ 4.250180] OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value. [ 4.254094] #1: ffff80008299bd80 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x1b8/0x62c [ 4.254109] #2: ffff00000920c8f8 [ 4.258345] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'bitclock-master' with a value. [ 4.264803] (&dev->mutex){....}-{4:4}, at: __device_attach_async_helper+0x3c/0xdc [ 4.264820] #3: ffff00000a50ca40 (request_class#2){+.+.}-{4:4}, at: __setup_irq+0xa0/0x690 [ 4.264840] #4: [ 4.268872] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'frame-master' with a value. [ 4.273275] ffff00000a50c8c8 (lock_class){....}-{2:2}, at: __setup_irq+0xc4/0x690 [ 4.296130] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz [ 4.304082] stack backtrace: [ 4.304086] CPU: 1 UID: 0 PID: 76 Comm: kworker/u8:5 Not tainted 6.13.0-rc7-arm64-renesas-05496-gd088502a519f #35 [ 4.304092] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 4.304097] Workqueue: async async_run_entry_fn [ 4.304106] Call trace: [ 4.304110] show_stack+0x14/0x20 (C) [ 4.304122] dump_stack_lvl+0x6c/0x90 [ 4.304131] dump_stack+0x14/0x1c [ 4.304138] __lock_acquire+0xdfc/0x1584 [ 4.426274] lock_acquire+0x1c4/0x33c [ 4.429942] _raw_spin_lock_irqsave+0x5c/0x80 [ 4.434307] gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.440061] gpio_rcar_irq_set_type+0xd4/0xd8 [ 4.444422] __irq_set_trigger+0x5c/0x178 [ 4.448435] __setup_irq+0x2e4/0x690 [ 4.452012] request_threaded_irq+0xc4/0x190 [ 4.456285] devm_request_threaded_irq+0x7c/0xf4 [ 4.459398] ata1: link resume succeeded after 1 retries [ 4.460902] mmc_gpiod_request_cd_irq+0x68/0xe0 [ 4.470660] mmc_start_host+0x50/0xac [ 4.474327] mmc_add_host+0x80/0xe4 [ 4.477817] tmio_mmc_host_probe+0x2b0/0x440 [ 4.482094] renesas_sdhi_probe+0x488/0x6f4 [ 4.486281] renesas_sdhi_internal_dmac_probe+0x60/0x78 [ 4.491509] platform_probe+0x64/0xd8 [ 4.495178] really_probe+0xb8/0x2a8 [ 4.498756] __driver_probe_device+0x74/0x118 [ 4.503116] driver_probe_device+0x3c/0x154 [ 4.507303] __device_attach_driver+0xd4/0x160 [ 4.511750] bus_for_each_drv+0x84/0xe0 [ 4.515588] __device_attach_async_helper+0xb0/0xdc [ 4.520470] async_run_entry_fn+0x30/0xd8 [ 4.524481] process_one_work+0x210/0x62c [ 4.528494] worker_thread+0x1ac/0x340 [ 4.532245] kthread+0x10c/0x110 [ 4.535476] ret_from_fork+0x10/0x20 Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250121135833.3769310-1-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> [PL: manullay applied the changes] Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Pavel Machek <pavel@denx.de> # for 5.10-stable Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-08-28gpio: tps65912: check the return value of regmap_update_bits()Bartosz Golaszewski1-2/+5
[ Upstream commit a0b2a6bbff8c26aafdecd320f38f52c341d5cafa ] regmap_update_bits() can fail, check its return value like we do elsewhere in the driver. Link: https://lore.kernel.org/r/20250707-gpiochip-set-rv-gpio-round4-v1-2-35668aaaf6d2@linaro.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-08-28gpio: wcd934x: check the return value of regmap_update_bits()Bartosz Golaszewski1-2/+5
[ Upstream commit ff0f0d7c6587e38c308be9905e36f86e98fb9c1f ] regmap_update_bits() can fail so check its return value in wcd_gpio_direction_output() for consistency with the rest of the code and propagate any errors. Link: https://lore.kernel.org/r/20250709-gpiochip-set-rv-gpio-remaining-v1-2-b8950f69618d@linaro.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-05-02gpio: zynq: Fix wakeup source leaks on device unbindKrzysztof Kozlowski1-0/+1
commit c5672e310ad971d408752fce7596ed27adc6008f upstream. Device can be unbound, so driver must also release memory for the wakeup source. Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20250406202245.53854-2-krzysztof.kozlowski@linaro.org Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-03-13gpio: rcar: Fix missing of_node_put() callFabrizio Castro1-1/+6
[ Upstream commit 391b41f983bf7ff853de44704d8e14e7cc648a9b ] of_parse_phandle_with_fixed_args() requires its caller to call into of_node_put() on the node pointer from the output structure, but such a call is currently missing. Call into of_node_put() to rectify that. Fixes: 159f8a0209af ("gpio-rcar: Add DT support") Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20250305163753.34913-2-fabrizio.castro.jz@renesas.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-03-13gpio: aggregator: protect driver attr handlers against module unloadKoichiro Den1-3/+17
commit 12f65d1203507f7db3ba59930fe29a3b8eee9945 upstream. Both new_device_store and delete_device_store touch module global resources (e.g. gpio_aggregator_lock). To prevent race conditions with module unload, a reference needs to be held. Add try_module_get() in these handlers. For new_device_store, this eliminates what appears to be the most dangerous scenario: if an id is allocated from gpio_aggregator_idr but platform_device_register has not yet been called or completed, a concurrent module unload could fail to unregister/delete the device, leaving behind a dangling platform device/GPIO forwarder. This can result in various issues. The following simple reproducer demonstrates these problems: #!/bin/bash while :; do # note: whether 'gpiochip0 0' exists or not does not matter. echo 'gpiochip0 0' > /sys/bus/platform/drivers/gpio-aggregator/new_device done & while :; do modprobe gpio-aggregator modprobe -r gpio-aggregator done & wait Starting with the following warning, several kinds of warnings will appear and the system may become unstable: ------------[ cut here ]------------ list_del corruption, ffff888103e2e980->next is LIST_POISON1 (dead000000000100) WARNING: CPU: 1 PID: 1327 at lib/list_debug.c:56 __list_del_entry_valid_or_report+0xa3/0x120 [...] RIP: 0010:__list_del_entry_valid_or_report+0xa3/0x120 [...] Call Trace: <TASK> ? __list_del_entry_valid_or_report+0xa3/0x120 ? __warn.cold+0x93/0xf2 ? __list_del_entry_valid_or_report+0xa3/0x120 ? report_bug+0xe6/0x170 ? __irq_work_queue_local+0x39/0xe0 ? handle_bug+0x58/0x90 ? exc_invalid_op+0x13/0x60 ? asm_exc_invalid_op+0x16/0x20 ? __list_del_entry_valid_or_report+0xa3/0x120 gpiod_remove_lookup_table+0x22/0x60 new_device_store+0x315/0x350 [gpio_aggregator] kernfs_fop_write_iter+0x137/0x1f0 vfs_write+0x262/0x430 ksys_write+0x60/0xd0 do_syscall_64+0x6c/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e [...] </TASK> ---[ end trace 0000000000000000 ]--- Fixes: 828546e24280 ("gpio: Add GPIO Aggregator") Cc: stable@vger.kernel.org Signed-off-by: Koichiro Den <koichiro.den@canonical.com> Link: https://lore.kernel.org/r/20250224143134.3024598-2-koichiro.den@canonical.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-03-13gpio: stmpe: Check return value of stmpe_reg_read in stmpe_gpio_irq_sync_unlockWentao Liang1-3/+12
commit b9644fbfbcab13da7f8b37bef7c51e5b8407d031 upstream. The stmpe_reg_read function can fail, but its return value is not checked in stmpe_gpio_irq_sync_unlock. This can lead to silent failures and incorrect behavior if the hardware access fails. This patch adds checks for the return value of stmpe_reg_read. If the function fails, an error message is logged and the function returns early to avoid further issues. Fixes: b888fb6f2a27 ("gpio: stmpe: i2c transfer are forbiden in atomic context") Cc: stable@vger.kernel.org # 4.16+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Link: https://lore.kernel.org/r/20250212021849.275-1-vulab@iscas.ac.cn Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2025-03-13gpio: bcm-kona: Add missing newline to dev_err format stringArtur Weber1-1/+1
[ Upstream commit 615279db222c3ac56d5c93716efd72b843295c1f ] Add a missing newline to the format string of the "Couldn't get IRQ for bank..." error message. Fixes: 757651e3d60e ("gpio: bcm281xx: Add GPIO driver") Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Markus Mayer <mmayer@broadcom.com> Signed-off-by: Artur Weber <aweber.kernel@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-3-409135eab780@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-03-13gpio: bcm-kona: Make sure GPIO bits are unlocked when requesting IRQArtur Weber1-12/+55
[ Upstream commit 57f5db77a915cc29461a679a6bcae7097967be1a ] The settings for all GPIOs are locked by default in bcm_kona_gpio_reset. The settings for a GPIO are unlocked when requesting it as a GPIO, but not when requesting it as an interrupt, causing the IRQ settings to not get applied. Fix this by making sure to unlock the right bits when an IRQ is requested. To avoid a situation where an IRQ being released causes a lock despite the same GPIO being used by a GPIO request or vice versa, add an unlock counter and only lock if it reaches 0. Fixes: 757651e3d60e ("gpio: bcm281xx: Add GPIO driver") Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Markus Mayer <mmayer@broadcom.com> Signed-off-by: Artur Weber <aweber.kernel@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-2-409135eab780@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-03-13gpio: bcm-kona: Fix GPIO lock/unlock for banks above bank 0Artur Weber1-2/+4
[ Upstream commit de1d0d160f64ee76df1d364d521b2faf465a091c ] The GPIO lock/unlock functions clear/write a bit to the relevant register for each bank. However, due to an oversight the bit that was being written was based on the total GPIO number, not the index of the GPIO within the relevant bank, causing it to fail for any GPIO above 32 (thus any GPIO for banks above bank 0). Fix lock/unlock for these banks by using the correct bit. Fixes: bdb93c03c550 ("gpio: bcm281xx: Centralize register locking") Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Markus Mayer <mmayer@broadcom.com> Signed-off-by: Artur Weber <aweber.kernel@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20250206-kona-gpio-fixes-v2-1-409135eab780@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-03-13gpio: pca953x: Improve interrupt supportMark Tomlinson1-19/+0
[ Upstream commit d6179f6c6204f9932aed3a7a2100b4a295dfed9d ] The GPIO drivers with latch interrupt support (typically types starting with PCAL) have interrupt status registers to determine which particular inputs have caused an interrupt. Unfortunately there is no atomic operation to read these registers and clear the interrupt. Clearing the interrupt is done by reading the input registers. The code was reading the interrupt status registers, and then reading the input registers. If an input changed between these two events it was lost. The solution in this patch is to revert to the non-latch version of code, i.e. remembering the previous input status, and looking for the changes. This system results in no more I2C transfers, so is no slower. The latch property of the device still means interrupts will still be noticed if the input changes back to its initial state. Fixes: 44896beae605 ("gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2") Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240606033102.2271916-1-mark.tomlinson@alliedtelesis.co.nz Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2025-02-01gpiolib: cdev: Fix use after free in lineinfo_changed_notifyZhongqiu Han1-1/+1
commit 02f6b0e1ec7e0e7d059dddc893645816552039da upstream. The use-after-free issue occurs as follows: when the GPIO chip device file is being closed by invoking gpio_chrdev_release(), watched_lines is freed by bitmap_free(), but the unregistration of lineinfo_changed_nb notifier chain failed due to waiting write rwsem. Additionally, one of the GPIO chip's lines is also in the release process and holds the notifier chain's read rwsem. Consequently, a race condition leads to the use-after-free of watched_lines. Here is the typical stack when issue happened: [free] gpio_chrdev_release() --> bitmap_free(cdev->watched_lines) <-- freed --> blocking_notifier_chain_unregister() --> down_write(&nh->rwsem) <-- waiting rwsem --> __down_write_common() --> rwsem_down_write_slowpath() --> schedule_preempt_disabled() --> schedule() [use] st54spi_gpio_dev_release() --> gpio_free() --> gpiod_free() --> gpiod_free_commit() --> gpiod_line_state_notify() --> blocking_notifier_call_chain() --> down_read(&nh->rwsem); <-- held rwsem --> notifier_call_chain() --> lineinfo_changed_notify() --> test_bit(xxxx, cdev->watched_lines) <-- use after free The side effect of the use-after-free issue is that a GPIO line event is being generated for userspace where it shouldn't. However, since the chrdev is being closed, userspace won't have the chance to read that event anyway. To fix the issue, call the bitmap_free() function after the unregistration of lineinfo_changed_nb notifier chain. Fixes: 51c1064e82e7 ("gpiolib: add new ioctl() for monitoring changes in line info") Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com> Link: https://lore.kernel.org/r/20240505141156.2944912-1-quic_zhonhan@quicinc.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Bruno VERNAY <bruno.vernay@se.com> Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-12-14gpio: grgpio: Add NULL check in grgpio_probeCharles Han1-0/+3
[ Upstream commit 050b23d081da0f29474de043e9538c1f7a351b3b ] devm_kasprintf() can return a NULL pointer on failure,but this returned value in grgpio_probe is not checked. Add NULL check in grgpio_probe, to handle kernel NULL pointer dereference error. Cc: stable@vger.kernel.org Fixes: 7eb6ce2f2723 ("gpio: Convert to using %pOF instead of full_name") Signed-off-by: Charles Han <hanchunchao@inspur.com> Link: https://lore.kernel.org/r/20241114091822.78199-1-hanchunchao@inspur.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-12-14gpio: grgpio: use a helper variable to store the address of ofdev->devBartosz Golaszewski1-11/+12
[ Upstream commit d036ae41cebdfae92666024163c109b8fef516fa ] Instead of dereferencing the platform device pointer repeatedly, just store its address in a helper variable. Link: https://lore.kernel.org/r/20241015131832.44678-3-brgl@bgdev.pl Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Stable-dep-of: 050b23d081da ("gpio: grgpio: Add NULL check in grgpio_probe") Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-10-17gpio: aspeed: Use devm_clk api to manage clock sourceBilly Tsai1-1/+1
[ Upstream commit a6191a3d18119184237f4ee600039081ad992320 ] Replace of_clk_get with devm_clk_get_enabled to manage the clock source. Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support") Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20241008081450.1490955-3-billy_tsai@aspeedtech.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-10-17gpio: aspeed: Add the flush write to ensure the write complete.Billy Tsai1-0/+2
[ Upstream commit 1bb5a99e1f3fd27accb804aa0443a789161f843c ] Performing a dummy read ensures that the register write operation is fully completed, mitigating any potential bus delays that could otherwise impact the frequency of bitbang usage. E.g., if the JTAG application uses GPIO to control the JTAG pins (TCK, TMS, TDI, TDO, and TRST), and the application sets the TCK clock to 1 MHz, the GPIO's high/low transitions will rely on a delay function to ensure the clock frequency does not exceed 1 MHz. However, this can lead to rapid toggling of the GPIO because the write operation is POSTed and does not wait for a bus acknowledgment. Fixes: 361b79119a4b ("gpio: Add Aspeed driver") Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20241008081450.1490955-2-billy_tsai@aspeedtech.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-10-17gpio: davinci: fix lazy disableEmanuele Ghidoli1-4/+4
commit 3360d41f4ac490282fddc3ccc0b58679aa5c065d upstream. On a few platforms such as TI's AM69 device, disable_irq() fails to keep track of the interrupts that happen between disable_irq() and enable_irq() and those interrupts are missed. Use the ->irq_unmask() and ->irq_mask() methods instead of ->irq_enable() and ->irq_disable() to correctly keep track of edges when disable_irq is called. This solves the issue of disable_irq() not working as expected on such platforms. Fixes: 23265442b02b ("ARM: davinci: irq_data conversion.") Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com> Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com> Acked-by: Keerthy <j-keerthy@ti.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240828133207.493961-1-parth105105@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-10-17gpiolib: cdev: Ignore reconfiguration without directionKent Gibson1-5/+8
commit b440396387418fe2feaacd41ca16080e7a8bc9ad upstream. linereq_set_config() behaves badly when direction is not set. The configuration validation is borrowed from linereq_create(), where, to verify the intent of the user, the direction must be set to in order to effect a change to the electrical configuration of a line. But, when applied to reconfiguration, that validation does not allow for the unset direction case, making it possible to clear flags set previously without specifying the line direction. Adding to the inconsistency, those changes are not immediately applied by linereq_set_config(), but will take effect when the line value is next get or set. For example, by requesting a configuration with no flags set, an output line with GPIO_V2_LINE_FLAG_ACTIVE_LOW and GPIO_V2_LINE_FLAG_OPEN_DRAIN set could have those flags cleared, inverting the sense of the line and changing the line drive to push-pull on the next line value set. Skip the reconfiguration of lines for which the direction is not set, and only reconfigure the lines for which direction is set. Fixes: a54756cb24ea ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL") Signed-off-by: Kent Gibson <warthog618@gmail.com> Link: https://lore.kernel.org/r/20240626052925.174272-3-warthog618@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-10-17gpio: prevent potential speculation leaks in gpio_device_get_desc()Hagar Hemdan1-1/+2
commit d795848ecce24a75dfd46481aee066ae6fe39775 upstream. Userspace may trigger a speculative read of an address outside the gpio descriptor array. Users can do that by calling gpio_ioctl() with an offset out of range. Offset is copied from user and then used as an array index to get the gpio descriptor without sanitization in gpio_device_get_desc(). This change ensures that the offset is sanitized by using array_index_nospec() to mitigate any possibility of speculative information leaks. This bug was discovered and resolved using Coverity Static Analysis Security Testing (SAST) by Synopsys, Inc. Signed-off-by: Hagar Hemdan <hagarhem@amazon.com> Link: https://lore.kernel.org/r/20240523085332.1801-1-hagarhem@amazon.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Hugo SIMELIERE <hsimeliere.opensource@witekio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05gpiolib: cdev: Disallow reconfiguration without direction (uAPI v1)Kent Gibson1-6/+10
[ Upstream commit 9919cce62f68e6ab68dc2a975b5dc670f8ca7d40 ] linehandle_set_config() behaves badly when direction is not set. The configuration validation is borrowed from linehandle_create(), where, to verify the intent of the user, the direction must be set to in order to effect a change to the electrical configuration of a line. But, when applied to reconfiguration, that validation does not allow for the unset direction case, making it possible to clear flags set previously without specifying the line direction. Adding to the inconsistency, those changes are not immediately applied by linehandle_set_config(), but will take effect when the line value is next get or set. For example, by requesting a configuration with no flags set, an output line with GPIOHANDLE_REQUEST_ACTIVE_LOW and GPIOHANDLE_REQUEST_OPEN_DRAIN requested could have those flags cleared, inverting the sense of the line and changing the line drive to push-pull on the next line value set. Ensure the intent of the user by disallowing configurations which do not have direction set, returning an error to userspace to indicate that the configuration is invalid. And, for clarity, use lflags, a local copy of gcnf.flags, throughout when dealing with the requested flags, rather than a mixture of both. Fixes: e588bb1eae31 ("gpio: add new SET_CONFIG ioctl() to gpio chardev") Signed-off-by: Kent Gibson <warthog618@gmail.com> Link: https://lore.kernel.org/r/20240626052925.174272-2-warthog618@gmail.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-07-05gpio: davinci: Validate the obtained number of IRQsAleksandr Mishin1-0/+5
[ Upstream commit 7aa9b96e9a73e4ec1771492d0527bd5fc5ef9164 ] Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken DT due to any error this value can be any. Without this value validation there can be out of chips->irqs array boundaries access in davinci_gpio_probe(). Validate the obtained nirq value so that it won't exceed the maximum number of IRQs per bank. Found by Linux Verification Center (linuxtesting.org) with SVACE. Fixes: eb3744a2dd01 ("gpio: davinci: Do not assume continuous IRQ numbering") Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru> Link: https://lore.kernel.org/r/20240618144344.16943-1-amishin@t-argos.ru Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-07-05gpio: tqmx86: store IRQ trigger type and unmask status separatelyMatthias Schiffer1-20/+26
commit 08af509efdf8dad08e972b48de0e2c2a7919ea8b upstream. irq_set_type() should not implicitly unmask the IRQ. All accesses to the interrupt configuration register are moved to a new helper tqmx86_gpio_irq_config(). We also introduce the new rule that accessing irq_type must happen while locked, which will become significant for fixing EDGE_BOTH handling. Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller") Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Link: https://lore.kernel.org/r/6aa4f207f77cb58ef64ffb947e91949b0f753ccd.1717063994.git.matthias.schiffer@ew.tq-group.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05gpio: tqmx86: fix typo in Kconfig labelGregor Herburger1-1/+1
[ Upstream commit 8c219e52ca4d9a67cd6a7074e91bf29b55edc075 ] Fix description for GPIO_TQMX86 from QTMX86 to TQMx86. Fixes: b868db94a6a7 ("gpio: tqmx86: Add GPIO from for this IO controller") Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com> Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/e0e38c9944ad6d281d9a662a45d289b88edc808e.1717063994.git.matthias.schiffer@ew.tq-group.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-05-17gpio: crystalcove: Use -ENOTSUPP consistentlyAndy Shevchenko1-1/+1
[ Upstream commit ace0ebe5c98d66889f19e0f30e2518d0c58d0e04 ] The GPIO library expects the drivers to return -ENOTSUPP in some cases and not using analogue POSIX code. Make the driver to follow this. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-05-17gpio: wcove: Use -ENOTSUPP consistentlyAndy Shevchenko1-1/+1
[ Upstream commit 0c3b532ad3fbf82884a2e7e83e37c7dcdd4d1d99 ] The GPIO library expects the drivers to return -ENOTSUPP in some cases and not using analogue POSIX code. Make the driver to follow this. Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-06gpio: fix resource unwinding order in error pathBartosz Golaszewski1-4/+4
[ Upstream commit ec5c54a9d3c4f9c15e647b049fea401ee5258696 ] Hogs are added *after* ACPI so should be removed *before* in error path. Fixes: a411e81e61df ("gpiolib: add hogs support for machine code") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-06gpiolib: Fix the error path order in gpiochip_add_data_with_key()Andy Shevchenko1-1/+1
[ Upstream commit e4aec4daa8c009057b5e063db1b7322252c92dc8 ] After shuffling the code, error path wasn't updated correctly. Fix it here. Fixes: 2f4133bb5f14 ("gpiolib: No need to call gpiochip_remove_pin_ranges() twice") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-03-06gpio: 74x164: Enable output pins after registers are resetArturas Moskvinas1-2/+2
[ Upstream commit 530b1dbd97846b110ea8a94c7cc903eca21786e5 ] Chip outputs are enabled[1] before actual reset is performed[2] which might cause pin output value to flip flop if previous pin value was set to 1. Fix that behavior by making sure chip is fully reset before all outputs are enabled. Flip-flop can be noticed when module is removed and inserted again and one of the pins was changed to 1 before removal. 100 microsecond flipping is noticeable on oscilloscope (100khz SPI bus). For a properly reset chip - output is enabled around 100 microseconds (on 100khz SPI bus) later during probing process hence should be irrelevant behavioral change. Fixes: 7ebc194d0fd4 (gpio: 74x164: Introduce 'enable-gpios' property) Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L130 [1] Link: https://elixir.bootlin.com/linux/v6.7.4/source/drivers/gpio/gpio-74x164.c#L150 [2] Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-23gpio: eic-sprd: Clear interrupt after set the interrupt typeWenhua Lin1-4/+28
[ Upstream commit 84aef4ed59705585d629e81d633a83b7d416f5fb ] The raw interrupt status of eic maybe set before the interrupt is enabled, since the eic interrupt has a latch function, which would trigger the interrupt event once enabled it from user side. To solve this problem, interrupts generated before setting the interrupt trigger type are ignored. Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support") Acked-by: Chunyan Zhang <zhang.lyra@gmail.com> Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2024-02-23gpiolib: acpi: Ignore touchpad wakeup on GPD G1619-04Mario Limonciello1-0/+14
commit 805c74eac8cb306dc69b87b6b066ab4da77ceaf1 upstream. Spurious wakeups are reported on the GPD G1619-04 which can be absolved by programming the GPIO to ignore wakeups. Cc: stable@vger.kernel.org Reported-and-tested-by: George Melikov <mail@gmelikov.ru> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3073 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-12-13gpiolib: sysfs: Fix error handling on failed exportBoerge Struempfel1-6/+9
[ Upstream commit 95dd1e34ff5bbee93a28ff3947eceaf6de811b1a ] If gpio_set_transitory() fails, we should free the GPIO again. Most notably, the flag FLAG_REQUESTED has previously been set in gpiod_request_commit(), and should be reset on failure. To my knowledge, this does not affect any current users, since the gpio_set_transitory() mainly returns 0 and -ENOTSUPP, which is converted to 0. However the gpio_set_transitory() function calles the .set_config() function of the corresponding GPIO chip and there are some GPIO drivers in which some (unlikely) branches return other values like -EPROBE_DEFER, and -EINVAL. In these cases, the above mentioned FLAG_REQUESTED would not be reset, which results in the pin being blocked until the next reboot. Fixes: e10f72bf4b3e ("gpio: gpiolib: Generalise state persistence beyond sleep") Signed-off-by: Boerge Struempfel <boerge.struempfel@gmail.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-10-25gpio: vf610: set value before the direction to avoid a glitchHaibo Chen1-2/+2
commit fc363413ef8ea842ae7a99e3caf5465dafdd3a49 upstream. We found a glitch when configuring the pad as output high. To avoid this glitch, move the data value setting before direction config in the function vf610_gpio_direction_output(). Fixes: 659d8a62311f ("gpio: vf610: add imx7ulp support") Signed-off-by: Haibo Chen <haibo.chen@nxp.com> [Bartosz: tweak the commit message] Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-25gpio: timberdale: Fix potential deadlock on &tgpio->lockChengfeng Ye1-2/+3
[ Upstream commit 9e8bc2dda5a7a8e2babc9975f4b11c9a6196e490 ] As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be executed under irq context, it could introduce double locks on &tgpio->lock if it preempts other execution units requiring the same locks. timbgpio_gpio_set() --> timbgpio_update_bit() --> spin_lock(&tgpio->lock) <interrupt> --> timbgpio_irq_disable() --> spin_lock_irqsave(&tgpio->lock) This flaw was found by an experimental static analysis tool I am developing for irq-related deadlock. To prevent the potential deadlock, the patch uses spin_lock_irqsave() on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible deadlock scenario. Signed-off-by: Chengfeng Ye <dg573847474@gmail.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-10-10gpio: pxa: disable pinctrl calls for MMP_GPIODuje Mihanović1-0/+1
commit f0575116507b981e6a810e78ce3c9040395b958b upstream. Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting pin direction on MMP either. Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request") Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr> Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-10gpio: aspeed: fix the GPIO number passed to pinctrl_gpio_set_config()Bartosz Golaszewski1-1/+1
commit f9315f17bf778cb8079a29639419fcc8a41a3c84 upstream. pinctrl_gpio_set_config() expects the GPIO number from the global GPIO numberspace, not the controller-relative offset, which needs to be added to the chip base. Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andy@kernel.org> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-10-10gpio: pmic-eic-sprd: Add can_sleep flag for PMIC EIC chipWenhua Lin1-0/+1
[ Upstream commit 26d9e5640d2130ee16df7b1fb6a908f460ab004c ] The drivers uses a mutex and I2C bus access in its PMIC EIC chip get implementation. This means these functions can sleep and the PMIC EIC chip should set the can_sleep property to true. This will ensure that a warning is printed when trying to get the value from a context that potentially can't sleep. Fixes: 348f3cde84ab ("gpio: Add Spreadtrum PMIC EIC driver support") Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-10-10gpio: tb10x: Fix an error handling path in tb10x_gpio_probe()Christophe JAILLET1-1/+5
[ Upstream commit b547b5e52a0587e6b25ea520bf2f9e03d00cbcb6 ] If an error occurs after a successful irq_domain_add_linear() call, it should be undone by a corresponding irq_domain_remove(), as already done in the remove function. Fixes: c6ce2b6bffe5 ("gpio: add TB10x GPIO driver") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-08-11gpio: tps68470: Make tps68470_gpio_output() always set the initial valueHans de Goede1-3/+3
[ Upstream commit 5a7adc6c1069ce31ef4f606ae9c05592c80a6ab5 ] Make tps68470_gpio_output() call tps68470_gpio_set() for output-only pins too, so that the initial value passed to gpiod_direction_output() is honored for these pins too. Fixes: 275b13a65547 ("gpio: Add support for TPS68470 GPIOs") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com> Tested-by: Daniel Scally <dan.scally@ideasonboard.com> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-06-28gpiolib: Fix GPIO chip IRQ initialization restrictionJiawen Wu1-0/+8
[ Upstream commit 8c00914e5438e3636f26b4f814b3297ae2a1b9ee ] In case of gpio-regmap, IRQ chip is added by regmap-irq and associated with GPIO chip by gpiochip_irqchip_add_domain(). The initialization flag was not added in gpiochip_irqchip_add_domain(), causing gpiochip_to_irq() to return -EPROBE_DEFER. Fixes: 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members before initialization") Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-06-28gpio: Allow per-parent interrupt dataMarc Zyngier1-2/+7
[ Upstream commit cfe6807d82e97e81c3209dca9448f091e1448a57 ] The core gpiolib code is able to deal with multiple interrupt parents for a single gpio irqchip. It however only allows a single piece of data to be conveyed to all flow handlers (either the gpio_chip or some other, driver-specific data). This means that drivers have to go through some interesting dance to find the correct context, something that isn't great in interrupt context (see aebdc8abc9db86e2bd33070fc2f961012fff74b4 for a prime example). Instead, offer an optional way for a pinctrl/gpio driver to provide an array of pointers which gets used to provide the correct context to the flow handler. Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Joey Gouly <joey.gouly@arm.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20211026175815.52703-2-joey.gouly@arm.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Stable-dep-of: 8c00914e5438 ("gpiolib: Fix GPIO chip IRQ initialization restriction") Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-05-30gpio: mockup: Fix mode of debugfs filesZev Weiss1-1/+1
commit 0a1bb16e0fe6650c3841e611de374bfd5578ad70 upstream. This driver's debugfs files have had a read operation since commit 2a9e27408e12 ("gpio: mockup: rework debugfs interface"), but were still being created with write-only mode bits. Update them to indicate that the files can also be read. Signed-off-by: Zev Weiss <zev@bewilderbeest.net> Fixes: 2a9e27408e12 ("gpio: mockup: rework debugfs interface") Cc: stable@kernel.org # v5.1+ Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2023-04-20gpio: davinci: Add irq chip flag to skip set wakeDhruva Gole1-1/+1
[ Upstream commit 7b75c4703609a3ebaf67271813521bc0281e1ec1 ] Add the IRQCHIP_SKIP_SET_WAKE flag since there are no special IRQ Wake bits that can be set to enable wakeup IRQ. Fixes: 3d9edf09d452 ("[ARM] 4457/2: davinci: GPIO support") Signed-off-by: Dhruva Gole <d-gole@ti.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-04-20gpio: GPIO_REGMAP: select REGMAP instead of depending on itRandy Dunlap1-1/+1
[ Upstream commit d49765b5f4320a402fbc4ed5edfd73d87640f27c ] REGMAP is a hidden (not user visible) symbol. Users cannot set it directly thru "make *config", so drivers should select it instead of depending on it if they need it. Consistently using "select" or "depends on" can also help reduce Kconfig circular dependency issues. Therefore, change the use of "depends on REGMAP" to "select REGMAP". Fixes: ebe363197e52 ("gpio: add a reusable generic gpio_chip using regmap") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Michael Walle <michael@walle.cc> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Bartosz Golaszewski <brgl@bgdev.pl> Cc: linux-gpio@vger.kernel.org Acked-by: Michael Walle <michael@walle.cc> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-03-11gpio: vf610: connect GPIO label to dev nameHaibo Chen1-1/+1
[ Upstream commit 6f8ecb7f85f441eb7d78ba2a4df45ee8a821934e ] Current GPIO label is fixed, so can't distinguish different GPIO controllers through labels. Use dev name instead. Fixes: 7f2691a19627 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid") Signed-off-by: Clark Wang <xiaoning.wang@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-02-01gpio: mxc: Always set GPIOs used as interrupt source to INPUT modeMarek Vasut1-1/+1
[ Upstream commit 8e88a0feebb241cab0253698b2f7358b6ebec802 ] Always configure GPIO pins which are used as interrupt source as INPUTs. In case the default pin configuration is OUTPUT, or the prior stage does configure the pins as OUTPUT, then Linux will not reconfigure the pin as INPUT and no interrupts are received. Always configure the interrupt source GPIO pin as input to fix the above case. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Fixes: 07bd1a6cc7cbb ("MXC arch: Add gpio support for the whole platform") Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-01-14gpio: sifive: Fix refcount leak in sifive_gpio_probeMiaoqian Lin1-0/+1
[ Upstream commit 694175cd8a1643cde3acb45c9294bca44a8e08e9 ] of_irq_find_parent() returns a node pointer with refcount incremented, We should use of_node_put() on it when not needed anymore. Add missing of_node_put() to avoid refcount leak. Fixes: 96868dce644d ("gpio/sifive: Add GPIO driver for SiFive SoCs") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2023-01-14gpiolib: cdev: fix NULL-pointer dereferencesBartosz Golaszewski1-0/+27
[ Upstream commit 533aae7c94dbc2b14301cfd68ae7e0e90f0c8438 ] There are several places where we can crash the kernel by requesting lines, unbinding the GPIO device, then calling any of the system calls relevant to the GPIO character device's annonymous file descriptors: ioctl(), read(), poll(). While I observed it with the GPIO simulator, it will also happen for any of the GPIO devices that can be hot-unplugged - for instance any HID GPIO expander (e.g. CP2112). This affects both v1 and v2 uAPI. This fixes it partially by checking if gdev->chip is not NULL but it doesn't entirely remedy the situation as we still have a race condition in which another thread can remove the device after the check. Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines") Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL") Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL") Fixes: a54756cb24ea ("gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL") Fixes: 7b8e00d98168 ("gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2026-01-24 19:18:42 +0300