| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A busy enough release, but not for the core which has only seen very
small updates. The biggest addition is the readdition of support for
detailed configuration of the timings around chip selects. That had
been removed for lack of use but there's been applications found for
it on Atmel systems. Otherwise the updates are mostly feature
additions and cleanups to existing drivers.
Summary:
- Provide a helper for getting device match data in a way that
abstracts away which firmware interface is being used.
- Re-add the spi_set_cs_timing() API for detailed configuration of
the timing around chip select and support it on Atmel.
- Support for MediaTek MT7986, Microchip PCI1xxxx, Nuvoton WPCM450
FIU and Socionext F_OSPI"
* tag 'spi-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
spi: dt-bindings: Convert Synquacer SPI to DT schema
spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
spi: spi-mtk-nor: Add recovery mechanism for dma read timeout
spi: spi-fsl-lpspi: add num-cs binding for lpspi
spi: spi-fsl-lpspi: support multiple cs for lpspi
spi: mtk-snfi: Add snfi support for MT7986 IC
spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
spi: cadence-quadspi: Add minimum operable clock rate warning to baudrate divisor calculation
spi: microchip: pci1xxxx: Add suspend and resume support for PCI1XXXX SPI driver
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix warning in example (missing reg property)
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix error in example (bogus include)
spi: mediatek: Enable irq when pdata is ready
spi: spi-mtk-nor: Unify write buffer on/off
spi: intel: Add support for SFDP opcode
spi: intel: Take possible chip address into account in intel_spi_read/write_reg()
spi: intel: Implement adjust_op_size()
spi: intel: Use ->replacement_op in intel_spi_hw_cycle()
spi: cadence: Drop obsolete dependency on COMPILE_TEST
spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings
spi: wpcm-fiu: Add direct map support
...
|
|
Pull drm updates from Dave Airlie:
"The biggest highlight is that the accel subsystem framework is merged.
Hopefully for 6.3 we will be able to line up a driver to use it.
In drivers land, i915 enables DG2 support by default now, and nouveau
has a big stability refactoring and initial ampere support, AMD
includes new hw IP support and should build on ARM again. There is
also an ofdrm driver to take over offb on platforms it's used.
Stuff outside my tree, the dma-buf patches hit a few places, the vc4
firmware changes also do, and i915 has some interactions with MEI for
discrete GPUs. I think all of those should have been acked/reviewed by
relevant parties.
New driver:
- ofdrm - replacement for offb
fbdev:
- add support for nomodeset
fourcc:
- add Vivante tiled modifier
core:
- atomic-helpers: CRTC primary plane test fixes, fb access hooks
- connector: TV API consistency, cmdline parser improvements
- send connector hotplug on cleanup
- sort makefile objects
tests:
- sort kunit tests
- improve DP-MST tests
- add kunit helpers to create a device
sched:
- module param for scheduling policy
- refcounting fix
buddy:
- add back random seed log
ttm:
- convert ttm_resource to size_t
- optimize pool allocations
edid:
- HFVSDB parsing support fixes
- logging/debug improvements
- DSC quirks
dma-buf:
- Add unlocked vmap and attachment mapping
- move drivers to common locking convention
- locking improvements
firmware:
- new API for rPI firmware and vc4
xilinx:
- zynqmp: displayport bridge support
- dpsub fix
bridge:
- adv7533: Remove dynamic lane switching
- it6505: Runtime PM support, sync improvements
- ps8640: Handle AUX defer messages
- tc358775: Drop soft-reset over I2C
panel:
- panel-edp: Add INX N116BGE-EA2 C2 and C4 support.
- Jadard JD9365DA-H3
- NewVision NV3051D
amdgpu:
- DCN support on ARM
- DCN 2.1 secure display
- Sienna Cichlid mode2 reset fixes
- new GC 11.x firmware versions
- drop AMD specific DSC workarounds in favour of drm code
- clang warning fixes
- scheduler rework
- SR-IOV fixes
- GPUVM locking fixes
- fix memory leak in CS IOCTL error path
- flexible array updates
- enable new GC/PSP/SMU/NBIO IP
- GFX preemption support for gfx9
amdkfd:
- cache size fixes
- userptr fixes
- enable cooperative launch on gfx 10.3
- enable GC 11.0.4 KFD support
radeon:
- replace kmap with kmap_local_page
- ACPI ref count fix
- HDA audio notifier support
i915:
- DG2 enabled by default
- MTL enablement work
- hotplug refactoring
- VBT improvements
- Display and watermark refactoring
- ADL-P workaround
- temp disable runtime_pm for discrete-
- fix for A380 as a secondary GPU
- Wa_18017747507 for DG2
- CS timestamp support fixes for gen5 and earlier
- never purge busy TTM objects
- use i915_sg_dma_sizes for all backends
- demote GuC kernel contexts to normal priority
- gvt: refactor for new MDEV interface
- enable DC power states on eDP ports
- fix gen 2/3 workarounds
nouveau:
- fix page fault handling
- Ampere acceleration support
- driver stability improvements
- nva3 backlight support
msm:
- MSM_INFO_GET_FLAGS support
- DPU: XR30 and P010 image formats
- Qualcomm SM6115 support
- DSI PHY support for QCM2290
- HDMI: refactored dev init path
- remove exclusive-fence hack
- fix speed-bin detection
- enable clamp to idle on 7c3
- improved hangcheck detection
vmwgfx:
- fb and cursor refactoring
- convert to generic hashtable
- cursor improvements
etnaviv:
- hw workarounds
- softpin MMU fixes
ast:
- atomic gamma LUT support
- convert to SHMEM
lcdif:
- support YUV planes
- Increase DMA burst size
- FIFO threshold tuning
meson:
- fix return type of cvbs mode_valid
mgag200:
- fix PLL setup on some revisions
sun4i:
- A100 and D1 support
udl:
- modesetting improvements
- hot unplug support
vc4:
- support PAL-M
- fix regression preventing 4K @ 60Hz
- fix NULL ptr deref
v3d:
- switch to drm managed resources
renesas:
- RZ/G2L DSI support
- DU Kconfig cleanup
mediatek:
- fixup dpi and hdmi
- MT8188 dpi support
- MT8195 AFBC support
tegra:
- NVDEC hardware on Tegra234 SoC
hdlcd:
- switch to drm managed resources
ingenic:
- fix registration error path
hisilicon:
- convert to drm_mode_init
maildp:
- use managed resources
mtk:
- use drm_mode_init
rockchip:
- use drm_mode_copy"
* tag 'drm-next-2022-12-13' of git://anongit.freedesktop.org/drm/drm: (1397 commits)
drm/amdgpu: fix mmhub register base coding error
drm/amdgpu: add tmz support for GC IP v11.0.4
drm/amdgpu: enable GFX Clock Gating control for GC IP v11.0.4
drm/amdgpu: enable GFX Power Gating for GC IP v11.0.4
drm/amdgpu: enable GFX IP v11.0.4 CG support
drm/amdgpu: Make amdgpu_ring_mux functions as static
drm/amdgpu: generally allow over-commit during BO allocation
drm/amd/display: fix array index out of bound error in DCN32 DML
drm/amd/display: 3.2.215
drm/amd/display: set optimized required for comp buf changes
drm/amd/display: Add debug option to skip PSR CRTC disable
drm/amd/display: correct DML calc error of UrgentLatency
drm/amd/display: correct static_screen_event_mask
drm/amd/display: Ensure commit_streams returns the DC return code
drm/amd/display: read invalid ddc pin status cause engine busy
drm/amd/display: Bypass DET swath fill check for max clocks
drm/amd/display: Disable uclk pstate for subvp pipes
drm/amd/display: Fix DCN2.1 default DSC clocks
drm/amd/display: Enable dp_hdmi21_pcon support
drm/amd/display: prevent seamless boot on displays that don't have the preferred dig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This looks like a relatively calm development cycle; there have been
only few changes in ALSA and ASoC core sides while we get lots of
device-specific fixes and updates as usual. Most of commits are about
ASoC, including Intel SOF/AVS and many device tree updates.
Below are some highlights:
Core:
- Improvement in memalloc helper for fallback allocations
- More cleanups of ASoC DAPM code
ASoC:
- Factoring out of mapping hw_params onto SoundWire configuration
- The ever ongoing overhauls of the Intel DSP code continue,
including support for loading libraries and probes with IPC4 on
SOF.
- Support for more sample formats on JZ4740
- Lots of device tree conversions and fixups
- Support for Allwinner D1, a range of AMD and Intel systems,
Mediatek systems with multiple DMICs, Nuvoton NAU8318, NXP
fsl_rpmsg and i.MX93, Qualcomm AudioReach Enable, MFC and SAL,
RealTek RT1318 and Rockchip RK3588
ALSA:
- Addition of PCM kselftest; still minimalistic but can be extended
in future
- Fixes for corner-case XRUNs with USB-audio implicit feedback mode
- Usual device-specific quirk updates for USB- and HD-audio
- FireWire DICE updates
This also contains a few cross-tree updates:
- Some OMAP board file updates for removal of relevant OMAP platforms
- A new I2C API update for I2C probe API adaption
- A DRM update for the further hdmi-codec updates"
* tag 'sound-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (417 commits)
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
ALSA: patch_realtek: Fix Dell Inspiron Plus 16
ALSA: hda/cirrus: Add extra 10 ms delay to allow PLL settle and lock.
ASoC: dt-bindings: Correct Alexandre Belloni email
ASoC: dt-bindings: maxim,max98504: Convert to DT schema
ASoC: dt-bindings: maxim,max98357a: Convert to DT schema
ASoC: dt-bindings: Reference common DAI properties
ASoC: dt-bindings: Extend name-prefix.yaml into common DAI properties
ASoC: rt715: Make read-only arrays capture_reg_H and capture_reg_L static const
ASoC: uniphier: aio-core: Make some read-only arrays static const
ASoC: wcd938x: Make read-only array minCode_param static const
ASoC: qcom: lpass-sc7280: Add maybe_unused tag for system PM ops
ASoC : SOF: amd: Add support for IPC and DSP dumps
ASoC: SOF: amd: Use poll function instead to read ACP_SHA_DSP_FW_QUALIFIER
ALSA: usb-audio: Workaround for XRUN at prepare
ALSA: pcm: Handle XRUN at trigger START
ALSA: pcm: Set missing stop_operating flag at undoing trigger start
drm: tda99x: Don't advertise non-existent capture support
ASoC: hdmi-codec: Allow playback and capture to be disabled
kselftest/alsa: Add more coverage of sample rates and channel counts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Make ghes_edac a simple module like the rest of the EDAC drivers and
drop the forced built-in only configuration by disentangling it from
GHES (Jia He)
- The usual small cleanups and improvements all over EDAC land
* tag 'edac_updates_for_6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/i10nm: fix refcount leak in pci_get_dev_wrapper()
EDAC/i5400: Fix typo in comment: vaious -> various
EDAC/mc_sysfs: Increase legacy channel support to 12
MAINTAINERS: Make Mauro EDAC reviewer
MAINTAINERS: Make Manivannan Sadhasivam the maintainer of qcom_edac
EDAC/igen6: Return the correct error type when not the MC owner
apei/ghes: Use xchg_release() for updating new cache slot instead of cmpxchg()
EDAC: Check for GHES preference in the chipset-specific EDAC drivers
EDAC/ghes: Make ghes_edac a proper module
EDAC/ghes: Prepare to make ghes_edac a proper module
EDAC/ghes: Add a notifier for reporting memory errors
efi/cper: Export several helpers for ghes_edac to use
EDAC/i5000: Mark as BROKEN
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are few major updates in the SoC specific drivers, mainly the
usual reworks and support for variants of the existing SoC. While this
remains Arm centric for the most part, the branch now also contains
updates to risc-v and loongarch specific code in drivers/soc/.
Notable changes include:
- Support for the newly added Qualcomm Snapdragon variants (MSM8956,
MSM8976, SM6115, SM4250, SM8150, SA8155 and SM8550) in the soc ID,
rpmh, rpm, spm and powerdomain drivers.
- Documentation for the somewhat controversial qcom,board-id
properties that are required for booting a number of machines
- A new SoC identification driver for the loongson-2 (loongarch)
platform
- memory controller updates for stm32, tegra, and renesas.
- a new DT binding to better describe LPDDR2/3/4/5 chips in the
memory controller subsystem
- Updates for Tegra specific drivers across multiple subsystems,
improving support for newer SoCs and better identification
- Minor fixes for Broadcom, Freescale, Apple, Renesas, Sifive, TI,
Mediatek and Marvell SoC drivers"
* tag 'soc-drivers-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (137 commits)
soc: qcom: socinfo: Add SM6115 / SM4250 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for SM6115 / SM4250 and variants
soc: qcom: socinfo: Add SM8150 and SA8155 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for SM8150 and SA8155
dt-bindings: soc: qcom: apr: document generic qcom,apr compatible
soc: qcom: Select REMAP_MMIO for ICC_BWMON driver
soc: qcom: Select REMAP_MMIO for LLCC driver
soc: qcom: rpmpd: Add SM4250 support
dt-bindings: power: rpmpd: Add SM4250 support
dt-bindings: soc: qcom: aoss: Add compatible for SM8550
soc: qcom: llcc: Add configuration data for SM8550
dt-bindings: arm: msm: Add LLCC compatible for SM8550
soc: qcom: llcc: Add v4.1 HW version support
soc: qcom: socinfo: Add SM8550 ID
soc: qcom: rpmh-rsc: Avoid unnecessary checks on irq-done response
soc: qcom: rpmh-rsc: Add support for RSC v3 register offsets
soc: qcom: rpmhpd: Add SM8550 power domains
dt-bindings: power: rpmpd: Add SM8550 to rpmpd binding
soc: qcom: socinfo: Add MSM8956/76 SoC IDs to the soc_id table
dt-bindings: arm: qcom,ids: Add SoC IDs for MSM8956 and MSM8976
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"The highlights this time are support for dynamically enabling and
disabling Clang's Shadow Call Stack at boot and a long-awaited
optimisation to the way in which we handle the SVE register state on
system call entry to avoid taking unnecessary traps from userspace.
Summary:
ACPI:
- Enable FPDT support for boot-time profiling
- Fix CPU PMU probing to work better with PREEMPT_RT
- Update SMMUv3 MSI DeviceID parsing to latest IORT spec
- APMT support for probing Arm CoreSight PMU devices
CPU features:
- Advertise new SVE instructions (v2.1)
- Advertise range prefetch instruction
- Advertise CSSC ("Common Short Sequence Compression") scalar
instructions, adding things like min, max, abs, popcount
- Enable DIT (Data Independent Timing) when running in the kernel
- More conversion of system register fields over to the generated
header
CPU misfeatures:
- Workaround for Cortex-A715 erratum #2645198
Dynamic SCS:
- Support for dynamic shadow call stacks to allow switching at
runtime between Clang's SCS implementation and the CPU's pointer
authentication feature when it is supported (complete with scary
DWARF parser!)
Tracing and debug:
- Remove static ftrace in favour of, err, dynamic ftrace!
- Seperate 'struct ftrace_regs' from 'struct pt_regs' in core ftrace
and existing arch code
- Introduce and implement FTRACE_WITH_ARGS on arm64 to replace the
old FTRACE_WITH_REGS
- Extend 'crashkernel=' parameter with default value and fallback to
placement above 4G physical if initial (low) allocation fails
SVE:
- Optimisation to avoid disabling SVE unconditionally on syscall
entry and just zeroing the non-shared state on return instead
Exceptions:
- Rework of undefined instruction handling to avoid serialisation on
global lock (this includes emulation of user accesses to the ID
registers)
Perf and PMU:
- Support for TLP filters in Hisilicon's PCIe PMU device
- Support for the DDR PMU present in Amlogic Meson G12 SoCs
- Support for the terribly-named "CoreSight PMU" architecture from
Arm (and Nvidia's implementation of said architecture)
Misc:
- Tighten up our boot protocol for systems with memory above 52 bits
physical
- Const-ify static keys to satisty jump label asm constraints
- Trivial FFA driver cleanups in preparation for v1.1 support
- Export the kernel_neon_* APIs as GPL symbols
- Harden our instruction generation routines against instrumentation
- A bunch of robustness improvements to our arch-specific selftests
- Minor cleanups and fixes all over (kbuild, kprobes, kfence, PMU, ...)"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (151 commits)
arm64: kprobes: Return DBG_HOOK_ERROR if kprobes can not handle a BRK
arm64: kprobes: Let arch do_page_fault() fix up page fault in user handler
arm64: Prohibit instrumentation on arch_stack_walk()
arm64:uprobe fix the uprobe SWBP_INSN in big-endian
arm64: alternatives: add __init/__initconst to some functions/variables
arm_pmu: Drop redundant armpmu->map_event() in armpmu_event_init()
kselftest/arm64: Allow epoll_wait() to return more than one result
kselftest/arm64: Don't drain output while spawning children
kselftest/arm64: Hold fp-stress children until they're all spawned
arm64/sysreg: Remove duplicate definitions from asm/sysreg.h
arm64/sysreg: Convert ID_DFR1_EL1 to automatic generation
arm64/sysreg: Convert ID_DFR0_EL1 to automatic generation
arm64/sysreg: Convert ID_AFR0_EL1 to automatic generation
arm64/sysreg: Convert ID_MMFR5_EL1 to automatic generation
arm64/sysreg: Convert MVFR2_EL1 to automatic generation
arm64/sysreg: Convert MVFR1_EL1 to automatic generation
arm64/sysreg: Convert MVFR0_EL1 to automatic generation
arm64/sysreg: Convert ID_PFR2_EL1 to automatic generation
arm64/sysreg: Convert ID_PFR1_EL1 to automatic generation
arm64/sysreg: Convert ID_PFR0_EL1 to automatic generation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Add NMI-safe SRCU reader API. It uses atomic_inc() instead of
this_cpu_inc() on strong load-store architectures.
- Introduce new console_list_lock to synchronize a manipulation of the
list of registered consoles and their flags.
This is a first step in removing the big-kernel-lock-like behavior of
console_lock(). This semaphore still serializes console->write()
calbacks against:
- each other. It primary prevents potential races between early
and proper console drivers using the same device.
- suspend()/resume() callbacks and init() operations in some
drivers.
- various other operations in the tty/vt and framebufer
susbsystems. It is likely that console_lock() serializes even
operations that are not directly conflicting with the
console->write() callbacks here. This is the most complicated
big-kernel-lock aspect of the console_lock() that will be hard
to untangle.
- Introduce new console_srcu lock that is used to safely iterate and
access the registered console drivers under SRCU read lock.
This is a prerequisite for introducing atomic console drivers and
console kthreads. It will reduce the complexity of serialization
against normal consoles and console_lock(). Also it should remove the
risk of deadlock during critical situations, like Oops or panic, when
only atomic consoles are registered.
- Check whether the console is registered instead of enabled on many
locations. It was a historical leftover.
- Cleanly force a preferred console in xenfb code instead of a dirty
hack.
- A lot of code and comment clean ups and improvements.
* tag 'printk-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux: (47 commits)
printk: htmldocs: add missing description
tty: serial: sh-sci: use setup() callback for early console
printk: relieve console_lock of list synchronization duties
tty: serial: kgdboc: use console_list_lock to trap exit
tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()
tty: serial: kgdboc: use console_list_lock for list traversal
tty: serial: kgdboc: use srcu console list iterator
proc: consoles: use console_list_lock for list iteration
tty: tty_io: use console_list_lock for list synchronization
printk, xen: fbfront: create/use safe function for forcing preferred
netconsole: avoid CON_ENABLED misuse to track registration
usb: early: xhci-dbc: use console_is_registered()
tty: serial: xilinx_uartps: use console_is_registered()
tty: serial: samsung_tty: use console_is_registered()
tty: serial: pic32_uart: use console_is_registered()
tty: serial: earlycon: use console_is_registered()
tty: hvc: use console_is_registered()
efi: earlycon: use console_is_registered()
tty: nfcon: use console_is_registered()
serial_core: replace uart_console_enabled() with uart_console_registered()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"A small collection of bug fixes, refactorings, and general
improvements:
- Reporting improvements and return path fixes (Guilherme G. Piccoli,
Wang Yufen, Kees Cook)
- Clean up kmsg_bytes module parameter usage (Guilherme G. Piccoli)
- Add Guilherme to pstore MAINTAINERS entry
- Choose friendlier allocation flags (Qiujun Huang, Stephen Boyd)"
* tag 'pstore-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore: Avoid kcore oops by vmap()ing with VM_IOREMAP
pstore/ram: Fix error return code in ramoops_probe()
pstore: Alert on backend write error
MAINTAINERS: Update pstore maintainers
pstore/ram: Set freed addresses to NULL
pstore/ram: Move internal definitions out of kernel-wide include
pstore/ram: Move pmsg init earlier
pstore/ram: Consolidate kfree() paths
efi: pstore: Follow convention for the efi-pstore backend name
pstore: Inform unregistered backend names as well
pstore: Expose kmsg_bytes as a module parameter
pstore: Improve error reporting in case of backend overlap
pstore/zone: Use GFP_ATOMIC to allocate zone buffer
|
|
* for-next/ffa:
firmware: arm_ffa: Move comment before the field it is documenting
firmware: arm_ffa: Move constants to header file
|
|
Merge series from Mark Brown <broonie@kernel.org>:
The recently added pcm-test selftest has pointed out that systems with
the tda998x driver end up advertising that they support capture when in
reality as far as I can see the tda998x devices are transmit only. The
DAIs registered through hdmi-codec are bidirectional, meaning that for
I2S systems when combined with a typical bidrectional CPU DAI the
overall capability of the PCM is bidirectional. In most cases the I2S
links will clock OK but no useful audio will be returned which isn't so
bad but we should still not advertise the useless capability, and some
systems may notice problems for example due to pinmux management.
This is happening due to the hdmi-codec helpers not providing any
mechanism for indicating unidirectional audio so add one and use it in
the tda998x driver. It is likely other hdmi-codec users are also
affected but I don't have those systems to hand.
Mark Brown (2):
ASoC: hdmi-codec: Allow playback and capture to be disabled
drm: tda99x: Don't advertise non-existent capture support
drivers/gpu/drm/i2c/tda998x_drv.c | 2 ++
include/sound/hdmi-codec.h | 4 ++++
sound/soc/codecs/hdmi-codec.c | 30 +++++++++++++++++++++++++-----
3 files changed, 31 insertions(+), 5 deletions(-)
base-commit: f0c4d9fc9cc9462659728d168387191387e903cc
--
2.30.2
|
|
The CON_ENABLED status of a console is a runtime setting that does not
involve the console driver. Drivers must not assume that if the console
is disabled then proper hardware management is not needed. For the EFI
earlycon case, it is about remapping/unmapping memory for the
framebuffer.
Use console_is_registered() instead of checking CON_ENABLED.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-25-john.ogness@linutronix.de
|
|
FF-A function IDs and error codes will be needed in the hypervisor too,
so move to them to the header file where they can be shared. Rename the
version constants with an "FFA_" prefix so that they are less likely
to clash with other code in the tree.
Co-developed-by: Andrew Walbran <qwandor@google.com>
Signed-off-by: Andrew Walbran <qwandor@google.com>
Signed-off-by: Quentin Perret <qperret@google.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20221116170335.2341003-2-qperret@google.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
into soc/drivers
This pull request contains Broadcom SoCs driver changes for 6.2, please
pull the following:
- Yuan uses dev_err_probe() in the Raspberry Pi firmware provider to
simplify the error handling code
- Rafal adds support for initialiazing the BCM47xx NVMEM/NVRAM firmware
provider out of memory-mapped flash devices.
* tag 'arm-soc/for-6.2/drivers' of https://github.com/Broadcom/stblinux:
firmware/nvram: bcm47xx: support init from IO memory
firmware: raspberrypi: Use dev_err_probe() to simplify code
Link: https://lore.kernel.org/r/20221129191755.542584-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merge series from Maarten Zanders <maarten.zanders@mind.be>:
A collection of fixes and improvements for the adau1372 driver.
|
|
Linux 6.1-rc4 which should get my CI working on RPi3s again.
|
|
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
Use EXPORT_SYMBOL_NS_GPL() instead of EXPORT_SYMBOL_GPL() and patch the
three drivers that use cs_dsp to add the MODULE_IMPORT_NS().
To make the namespace more specific the KConfig symbol for cs_dsp is
changed from CS_DSP to FW_CS_DSP.
|
|
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
Writing a firmware control should be returning 1 if the control value
changed, so these two patches add that.
Though this is an ALSA requirement it is also useful for non-ALSA clients
of cs_dsp to know if the control value changed, so the main handling is
implemented in cs_dsp. TLV controls are specifically an ALSA thing so they
are handled specially in wm_adsp.
Simon Trimmer (2):
firmware: cs_dsp: cs_dsp_coeff_write_ctrl() should report changed
ASoC: wm_adsp: Return whether changed when writing controls
drivers/firmware/cirrus/cs_dsp.c | 17 ++++++++++++-----
sound/soc/codecs/wm_adsp.c | 27 ++++++++++++++++++---------
2 files changed, 30 insertions(+), 14 deletions(-)
--
2.30.2
|
|
Move all the exports into a namespace.
This also adds the MODULE_IMPORT_NS to the 3 drivers that use the
exported functions.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221124134556.3343784-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Qualify the KConfig symbol for cs_dsp by adding a FW_ prefix so that
it is more explicit what is being referred to. This is preparation for
using the symbol to namespace the exports.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221124134556.3343784-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 6.1-rc6
This is needed for drm-misc-next and tegra.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
ALSA callers need to know whether there was a change to the value so
that they can report a control write change correctly.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165811.3014472-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BPMP firmware driver never worked on big-endian kernels, and
cannot easily be made portable. Add a dependency to make this clear
in case anyone ever wants to try a big-endian kernel on this hardware.
Link: https://lore.kernel.org/linux-arm-kernel/Y34FCQ3xTmcjqKRT@orome/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/drivers
TI SoC driver updates for v6.2 v2
* Minor bugfixes for knav_qmss_queue, smartreflex drivers
* API optimizations including using devm, bitmap apis to
ti-sci, soc-info drivers
* k3-ringacc can now be built as modules for certain
distros that mandate such usage.
* k3-socinfo can now detect AM62A SoCs.
* tag 'ti-driver-soc-for-v6.2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
soc: ti: k3-socinfo: Add AM62Ax JTAG ID
soc: ti: smartreflex: Fix PM disable depth imbalance in omap_sr_probe
soc: ti: knav_qmss_queue: Fix PM disable depth imbalance in knav_queue_probe
firmware: ti_sci: Use devm_bitmap_zalloc when applicable
soc: ti: k3-ringacc: Allow the driver to be built as module
firmware: ti_sci: Fix polled mode during system suspend
firmware: ti_sci: Use the non-atomic bitmap API when applicable
firmware: ti_sci: Use the bitmap API to allocate bitmaps
drivers: soc: ti: knav_qmss_queue: Mark knav_acc_firmwares as static
Link: https://lore.kernel.org/r/20221122223856.fwackjg7fbd5jcz7@wannabe
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into soc/drivers
firmware: tegra: Changes for v6.2-rc1
This adds new BPMP ABI so that newer features can be enabled.
Furthermore, the BPMP driver is updated to use iosys-map helpers to
allow working with shared memory regions that are located in system
memory.
Apart from that, several minor cleanups are included.
* tag 'tegra-for-6.2-firmware-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware: tegra: Remove surplus dev_err() when using platform_get_irq_byname()
firmware: tegra: Update BPMP ABI
firmware: tegra: bpmp: Do not support big-endian
firmware: tegra: bpmp: Use iosys-map helpers
firmware: tegra: bpmp: Prefer u32 over uint32_t
Link: https://lore.kernel.org/r/20221121171239.2041835-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
EFI has a rather unique benefit that it has access to some limited
non-volatile storage, where the kernel can store a random seed. Register
a notification for when the RNG is initialized, and at that point, store
a new random seed.
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/drivers
i.MX drivers change for 6.2:
- Improve imx8m-blk-ctrl driver to allow deferred probe in case that
'bus' genpd is not yet ready.
- Add missing USB_1_PHY PD for i.MX scu-pd firmware driver.
- Add GENPD_FLAG_ACTIVE_WAKEUP flag for i.MX8MM/N in GPCv2 driver, so
that the power domain remains on if USB remote wakeup is enabled.
* tag 'imx-drivers-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: gpcv2: add GENPD_FLAG_ACTIVE_WAKEUP flag for usb of imx8mm/n
firmware: imx: scu-pd: add missed USB_1_PHY pd
soc: imx: imx8m-blk-ctrl: Defer probe if 'bus' genpd is not yet ready
Link: https://lore.kernel.org/r/20221119125733.32719-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc and other driver fixes for 6.1-rc6 to
resolve some reported problems. Included in here are:
- iio driver fixes
- binder driver fix
- nvmem driver fix
- vme_vmci information leak fix
- parport fix
- slimbus configuration fix
- coreboot firmware bugfix
- speakup build fix and crash fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (22 commits)
firmware: coreboot: Register bus in module init
nvmem: u-boot-env: fix crc32_data_offset on redundant u-boot-env
slimbus: qcom-ngd: Fix build error when CONFIG_SLIM_QCOM_NGD_CTRL=y && CONFIG_QCOM_RPROC_COMMON=m
docs: update mediator contact information in CoC doc
slimbus: stream: correct presence rate frequencies
nvmem: lan9662-otp: Fix compatible string
binder: validate alloc->mm in ->mmap() handler
parport_pc: Avoid FIFO port location truncation
siox: fix possible memory leak in siox_device_add()
misc/vmw_vmci: fix an infoleak in vmci_host_do_receive_datagram()
speakup: replace utils' u_char with unsigned char
speakup: fix a segfault caused by switching consoles
tools: iio: iio_generic_buffer: Fix read size
iio: imu: bno055: uninitialized variable bug in bno055_trigger_handler()
iio: adc: at91_adc: fix possible memory leak in at91_adc_allocate_trigger()
iio: adc: mp2629: fix potential array out of bound access
iio: adc: mp2629: fix wrong comparison of channel
iio: pressure: ms5611: changed hardcoded SPI speed to value limited
iio: pressure: ms5611: fixed value compensation bug
iio: accel: bma400: Ensure VDDIO is enable defore reading the chip ID.
...
|
|
There is no need to call the dev_err() function directly to print a
custom message when handling an error from either the platform_get_irq()
or platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
./drivers/firmware/tegra/bpmp-tegra210.c:204:2-9: line 204 is redundant
because platform_get_irq() already prints an error
./drivers/firmware/tegra/bpmp-tegra210.c:216:2-9: line 216 is redundant
because platform_get_irq() already prints an error
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2579
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- Force the use of SetVirtualAddressMap() on Ampera Altra arm64
machines, which crash in SetTime() if no virtual remapping is used
This is the first time we've added an SMBIOS based quirk on arm64,
but fortunately, we can just call a EFI protocol to grab the type #1
SMBIOS record when running in the stub, so we don't need all the
machinery we have in the kernel proper to parse SMBIOS data.
- Drop a spurious warning on misaligned runtime regions when using 16k
or 64k pages on arm64
* tag 'efi-fixes-for-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
arm64: efi: Fix handling of misaligned runtime regions and drop warning
arm64: efi: Force the use of SetVirtualAddressMap() on Altra machines
|
|
Ampere Altra machines are reported to misbehave when the SetTime() EFI
runtime service is called after ExitBootServices() but before calling
SetVirtualAddressMap(). Given that the latter is horrid, pointless and
explicitly documented as optional by the EFI spec, we no longer invoke
it at boot if the configured size of the VA space guarantees that the
EFI runtime memory regions can remain mapped 1:1 like they are at boot
time.
On Ampere Altra machines, this results in SetTime() calls issued by the
rtc-efi driver triggering synchronous exceptions during boot. We can
now recover from those without bringing down the system entirely, due to
commit 23715a26c8d81291 ("arm64: efi: Recover from synchronous
exceptions occurring in firmware"). However, it would be better to avoid
the issue entirely, given that the firmware appears to remain in a funny
state after this.
So attempt to identify these machines based on the 'family' field in the
type #1 SMBIOS record, and call SetVirtualAddressMap() unconditionally
in that case.
Tested-by: Alexandru Elisei <alexandru.elisei@gmail.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The coreboot_table driver registers a coreboot bus while probing a
"coreboot_table" device representing the coreboot table memory region.
Probing this device (i.e., registering the bus) is a dependency for the
module_init() functions of any driver for this bus (e.g.,
memconsole-coreboot.c / memconsole_driver_init()).
With synchronous probe, this dependency works OK, as the link order in
the Makefile ensures coreboot_table_driver_init() (and thus,
coreboot_table_probe()) completes before a coreboot device driver tries
to add itself to the bus.
With asynchronous probe, however, coreboot_table_probe() may race with
memconsole_driver_init(), and so we're liable to hit one of these two:
1. coreboot_driver_register() eventually hits "[...] the bus was not
initialized.", and the memconsole driver fails to register; or
2. coreboot_driver_register() gets past #1, but still races with
bus_register() and hits some other undefined/crashing behavior (e.g.,
in driver_find() [1])
We can resolve this by registering the bus in our initcall, and only
deferring "device" work (scanning the coreboot memory region and
creating sub-devices) to probe().
[1] Example failure, using 'driver_async_probe=*' kernel command line:
[ 0.114217] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
[ 0.114307] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc1 #63
[ 0.114316] Hardware name: Google Scarlet (DT)
...
[ 0.114488] Call trace:
[ 0.114494] _raw_spin_lock+0x34/0x60
[ 0.114502] kset_find_obj+0x28/0x84
[ 0.114511] driver_find+0x30/0x50
[ 0.114520] driver_register+0x64/0x10c
[ 0.114528] coreboot_driver_register+0x30/0x3c
[ 0.114540] memconsole_driver_init+0x24/0x30
[ 0.114550] do_one_initcall+0x154/0x2e0
[ 0.114560] do_initcall_level+0x134/0x160
[ 0.114571] do_initcalls+0x60/0xa0
[ 0.114579] do_basic_setup+0x28/0x34
[ 0.114588] kernel_init_freeable+0xf8/0x150
[ 0.114596] kernel_init+0x2c/0x12c
[ 0.114607] ret_from_fork+0x10/0x20
[ 0.114624] Code: 5280002b 1100054a b900092a f9800011 (885ffc01)
[ 0.114631] ---[ end trace 0000000000000000 ]---
Fixes: b81e3140e412 ("firmware: coreboot: Make bus registration symmetric")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20221019180934.1.If29e167d8a4771b0bf4a39c89c6946ed764817b9@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Provide NVMEM content to the NVRAM driver from a simple
memory resource. This is necessary to use NVRAM in a memory-
mapped flash device. Patch taken from OpenWrts development
tree.
This patch makes it possible to use memory-mapped NVRAM
on the D-Link DWL-8610AP and the D-Link DIR-890L.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@vger.kernel.org
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[Added an export for modules potentially using the init symbol]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221103082529.359084-1-linus.walleij@linaro.org
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Enable asynchronous unwind table generation for both the core kernel as
well as modules, and emit the resulting .eh_frame sections as init code
so we can use the unwind directives for code patching at boot or module
load time.
This will be used by dynamic shadow call stack support, which will rely
on code patching rather than compiler codegen to emit the shadow call
stack push and pop instructions.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20221027155908.1940624-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- A pair of tweaks to the EFI random seed code so that externally
provided version of this config table are handled more robustly
- Another fix for the v6.0 EFI variable refactor that turned out to
break Apple machines which don't provide QueryVariableInfo()
- Add some guard rails to the EFI runtime service call wrapper so we
can recover from synchronous exceptions caused by firmware
* tag 'efi-fixes-for-v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
arm64: efi: Recover from synchronous exceptions occurring in firmware
efi: efivars: Fix variable writes with unsupported query_variable_store()
efi: random: Use 'ACPI reclaim' memory for random seed
efi: random: reduce seed size to 32 bytes
efi/tpm: Pass correct address to memblock_reserve
|
|
'xfer_alloc_table' is a bitmap. So use 'devm_bitmap_zalloc()' to simplify
code and improve the semantic of the code.
While at it, remove a redundant 'bitmap_zero()' call.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/43ab1a7dd073d0d037d5d4bbbd5f8335de605826.1667457664.git.christophe.jaillet@wanadoo.fr
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 6.2:
UAPI Changes:
Cross-subsystem Changes:
- dma-buf: locking improvements
- firmware: New API in the RaspberryPi firmware driver used by vc4
Core Changes:
- client: Null pointer dereference fix in drm_client_buffer_delete()
- mm/buddy: Add back random seed log
- ttm: Convert ttm_resource to use size_t for its size, fix for an
undefined behaviour
Driver Changes:
- bridge:
- adv7511: use dev_err_probe
- it6505: Fix return value check of pm_runtime_get_sync
- panel:
- sitronix: Fixes and clean-ups
- lcdif: Increase DMA burst size
- rockchip: runtime_pm improvements
- vc4: Fix for a regression preventing the use of 4k @ 60Hz, and
further HDMI rate constraints check.
- vmwgfx: Cursor improvements
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103083437.ksrh3hcdvxaof62l@houat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI fixes for v6.1
A bunch of fixes to handle:
1. A possible resource leak in scmi_remove(). The returned error
value gets ignored by the driver core and can remove the device and
free the devm-allocated resources. As a simple solution to be able to
easily backport, the bind attributes in the driver is suppressed as
there is no need to support it. Additionally the remove path is cleaned
up by adding device links between the core and the protocol devices
so that a proper and complete unbinding happens.
2. A possible spin-loop in the SCMI transmit path in case of misbehaving
platform firmware. A timeout is added to the existing loop so that
the SCMI stack can bailout aborting the transmission with warnings.
3. Optional Rx channel correctly by reporting any memory errors instead
of ignoring the same with other allowed errors.
4. The use of proper device for all the device managed allocations in the
virtio transport.
5. Incorrect deferred_tx_wq release on the error paths by using devres
API(devm_add_action_or_reset) to manage the release in the error path.
* tag 'scmi-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix deferred_tx_wq release on error paths
firmware: arm_scmi: Fix devres allocation device in virtio transport
firmware: arm_scmi: Make Rx chan_setup fail on memory errors
firmware: arm_scmi: Make tx_prepare time out eventually
firmware: arm_scmi: Suppress the driver's bind attributes
firmware: arm_scmi: Cleanup the core driver removal callback
Link: https://lore.kernel.org/r/20221102140142.2758107-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use devres to allocate the dedicated deferred_tx_wq polling workqueue so
as to automatically trigger the proper resource release on error path.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5a3b7185c47c ("firmware: arm_scmi: Add atomic mode support to virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-6-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
SCMI virtio transport device managed allocations must use the main
platform device in devres operations instead of the channel devices.
Cc: Peter Hilber <peter.hilber@opensynergy.com>
Fixes: 46abe13b5e3d ("firmware: arm_scmi: Add virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-5-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
SCMI Rx channels are optional and they can fail to be setup when not
present but anyway channels setup routines must bail-out on memory errors.
Make channels setup, and related probing, fail when memory errors are
reported on Rx channels.
Fixes: 5c8a47a5a91d ("firmware: arm_scmi: Make scmi core independent of the transport type")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-4-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
SCMI transports based on shared memory, at start of transmissions, have
to wait for the shared Tx channel area to be eventually freed by the
SCMI platform before accessing the channel. In fact the channel is owned
by the SCMI platform until marked as free by the platform itself and,
as such, cannot be used by the agent until relinquished.
As a consequence a badly misbehaving SCMI platform firmware could lock
the channel indefinitely and make the kernel side SCMI stack loop
forever waiting for such channel to be freed, possibly hanging the
whole boot sequence.
Add a timeout to the existent Tx waiting spin-loop so that, when the
system ends up in this situation, the SCMI stack can at least bail-out,
nosily warn the user, and abort the transmission.
Reported-by: YaxiongTian <iambestgod@outlook.com>
Suggested-by: YaxiongTian <iambestgod@outlook.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-3-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Suppress the capability to unbind the core SCMI driver since all the
SCMI stack protocol drivers depend on it.
Fixes: aa4f886f3893 ("firmware: arm_scmi: add basic driver infrastructure for SCMI")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Platform drivers .remove callbacks are not supposed to fail and report
errors. Such errors are indeed ignored by the core platform drivers
and the driver unbind process is anyway completed.
The SCMI core platform driver as it is now, instead, bails out reporting
an error in case of an explicit unbind request.
Fix the removal path by adding proper device links between the core SCMI
device and the SCMI protocol devices so that a full SCMI stack unbind is
triggered when the core driver is removed. The remove process does not
bail out anymore on the anomalous conditions triggered by an explicit
unbind but the user is still warned.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Commit 8a254d90a775 ("efi: efivars: Fix variable writes without
query_variable_store()") addressed an issue that was introduced during
the EFI variable store refactor, where alternative implementations of
the efivars layer that lacked query_variable_store() would no longer
work.
Unfortunately, there is another case to consider here, which was missed:
if the efivars layer is backed by the EFI runtime services as usual, but
the EFI implementation predates the introduction of QueryVariableInfo(),
we will return EFI_UNSUPPORTED, and this is no longer being dealt with
correctly.
So let's fix this, and while at it, clean up the code a bit, by merging
the check_var_size() routines as well as their callers.
Cc: <stable@vger.kernel.org> # v6.0
Fixes: bbc6d2c6ef22 ("efi: vars: Switch to new wrapper layer")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Aditya Garg <gargaditya08@live.com>
|
|
Commit b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled
mode during system suspend") uses read_poll_timeout_atomic() macro
in ti_sci_do_xfer() to wait for completion when the system is
suspending. The break condition of the macro is set to "true" which
will cause it break immediately when evaluated, likely before the
TISCI xfer is completed, and always return 0. We want to poll here
until "done_state == true".
1) Change the break condition of read_poll_timeout_atomic() to
the bool variable "done_state".
2) The read_poll_timeout_atomic() returns 0 if the break condition
is met or -ETIMEDOUT if not. Since our break condition has changed
to "done_state", we also don't have to check for "!done_state" when
evaluating the return value.
Fixes: b9e8a7d950ff ("firmware: ti_sci: Switch transport to polled mode during system suspend")
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221021185704.181316-1-g-vlaev@ti.com
|
|
Usages of the 'res_map' bitmap is protected with a spinlock, so non-atomic
functions can be used to set/clear bits.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/fb7edc555b6fa7c74707f13e422196693a834bc8.1657308216.git.christophe.jaillet@wanadoo.fr
|
|
Use devm_bitmap_zalloc() instead of hand-writing them.
It is less verbose and it improves the semantic.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/3ee11e9e83f7c1552d237f5c28f554319fcbbf1f.1657308216.git.christophe.jaillet@wanadoo.fr
|
|
The firmware allows to query for its clocks the operating range of a
given clock. We'll need this for some drivers (KMS, in particular) to
infer the state of some configuration options, so let's create a
function to do so.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-3-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
A significant number of RaspberryPi drivers using the firmware don't
have a phandle to it, so end up scanning the device tree to find a node
with the firmware compatible.
That code is duplicated everywhere, so let's introduce a helper instead.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220815-rpi-fix-4k-60-v5-1-fe9e7ac8b111@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
