| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit f147384774a7b24dda4783a3dcd61af272757ea8 ]
The commit af19b7ce76ba ("mmc: bcm2835: Avoid possible races on
data requests") introduces a possible circular locking dependency,
which is triggered by swapping to the sdhost interface.
So instead of reintroduce the race condition again, we could also
avoid this situation by using GFP_NOWAIT for the allocation of the
DMA buffer descriptors.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: af19b7ce76ba ("mmc: bcm2835: Avoid possible races on data requests")
Link: http://lists.infradead.org/pipermail/linux-rpi-kernel/2019-March/008615.html
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 5bb5c3a3ac102158b799bf5eda871223aa5e9c25 upstream.
This patch fixes wrong register usage in the mtk_cqdma_start. The
destination register should be MTK_CQDMA_DST2 instead.
Fixes: b1f01e48df5a ("dmaengine: mediatek: Add MediaTek Command-Queue DMA controller for MT6765 SoC")
Signed-off-by: Shun-Chih Yu <shun-chih.yu@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6e7da74775348d96e2d7efaf3f91410e18c481ef upstream.
The tx_status poll in the rcar_dmac driver reads the status register
which indicates which chunk is busy (DMACHCRB). Afterwards the point
inside the chunk is read from DMATCRB. It is possible that the chunk
has changed between the two reads. The result is a non-monotonous
increase of the residue. Fix this by introducing a 'safe read' logic.
Fixes: 73a47bd0da66 ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 907bd68a2edc491849e2fdcfe52c4596627bca94 upstream.
Having a cyclic DMA, a residue 0 is not an indication of a completed
DMA. In case of cyclic DMA make sure that dma_set_residue() is called
and with this a residue of 0 is forwarded correctly to the caller.
Fixes: 3544d2878817 ("dmaengine: rcar-dmac: use result of updated get_residue in tx_status")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Yao Lihua <ylhuajnu@outlook.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e486df39305864604b7e25f2a95d51039517ac57 ]
The dma_desc->bytes_transferred counter tracks the number of bytes
moved by the DMA channel. This is then used to calculate the information
passed back in the in the tegra_dma_tx_status callback, which is usually
fine.
When the DMA channel is configured as continous, then the bytes_transferred
counter will increase over time and eventually overflow to become negative
so the residue count will become invalid and the ALSA sound-dma code will
report invalid hardware pointer values to the application. This results in
some users becoming confused about the playout position and putting audio
data in the wrong place.
To fix this issue, always ensure the bytes_transferred field is modulo the
size of the request. We only do this for the case of the cyclic transfer
done ISR as anyone attempting to move 2GiB of DMA data in one transfer
is unlikely.
Note, we don't fix the issue that we should /never/ transfer a negative
number of bytes so we could make those fields unsigned.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 875aac8a46424e5b73a9ff7f40b83311b609e407 ]
In async_tx_test_ack(), it uses flags in struct dma_async_tx_descriptor
to check the ACK status. As hidma reuses the descriptor in a free list
when hidma_prep_dma_*(memcpy/memset) is called, the flag will keep ACKed
if the descriptor has been used before. This will cause a BUG_ON in
async_tx_quiesce().
kernel BUG at crypto/async_tx/async_tx.c:282!
Internal error: Oops - BUG: 0 1 SMP
...
task: ffff8017dd3ec000 task.stack: ffff8017dd3e8000
PC is at async_tx_quiesce+0x54/0x78 [async_tx]
LR is at async_trigger_callback+0x98/0x110 [async_tx]
This patch initializes flags in dma_async_tx_descriptor by the flags
passed from the caller when hidma_prep_dma_*(memcpy/memset) is called.
Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 546c0547555efca8ba8c120716c325435e29df1b ]
When dma_cookie_complete() is called in hidma_process_completed(),
dma_cookie_status() will return DMA_COMPLETE in hidma_tx_status(). Then,
hidma_txn_is_success() will be called to use channel cookie
mchan->last_success to do additional DMA status check. Current code
assigns mchan->last_success after dma_cookie_complete(). This causes
a race condition of dma_cookie_status() returns DMA_COMPLETE before
mchan->last_success is assigned correctly. The race will cause
hidma_tx_status() return DMA_ERROR but the transaction is actually a
success. Moreover, in async_tx case, it will cause a timeout panic
in async_tx_quiesce().
Kernel panic - not syncing: async_tx_quiesce: DMA error waiting for
transaction
...
Call trace:
[<ffff000008089994>] dump_backtrace+0x0/0x1f4
[<ffff000008089bac>] show_stack+0x24/0x2c
[<ffff00000891e198>] dump_stack+0x84/0xa8
[<ffff0000080da544>] panic+0x12c/0x29c
[<ffff0000045d0334>] async_tx_quiesce+0xa4/0xc8 [async_tx]
[<ffff0000045d03c8>] async_trigger_callback+0x70/0x1c0 [async_tx]
[<ffff0000048b7d74>] raid_run_ops+0x86c/0x1540 [raid456]
[<ffff0000048bd084>] handle_stripe+0x5e8/0x1c7c [raid456]
[<ffff0000048be9ec>] handle_active_stripes.isra.45+0x2d4/0x550 [raid456]
[<ffff0000048beff4>] raid5d+0x38c/0x5d0 [raid456]
[<ffff000008736538>] md_thread+0x108/0x168
[<ffff0000080fb1cc>] kthread+0x10c/0x138
[<ffff000008084d34>] ret_from_fork+0x10/0x18
Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9227ab5643cb8350449502dd9e3168a873ab0e3b ]
The warning got introduced by commit 930507c18304 ("arm64: add basic
Kconfig symbols for i.MX8"). Since it got enabled for arm64. The warning
haven't been seen before since size_t was 'unsigned int' when built on
arm32.
../drivers/dma/imx-dma.c: In function ‘imxdma_sg_next’:
../include/linux/kernel.h:846:29: warning: comparison of distinct pointer types lacks a cast
(!!(sizeof((typeof(x) *)1 == (typeof(y) *)1)))
^~
../include/linux/kernel.h:860:4: note: in expansion of macro ‘__typecheck’
(__typecheck(x, y) && __no_side_effects(x, y))
^~~~~~~~~~~
../include/linux/kernel.h:870:24: note: in expansion of macro ‘__safe_cmp’
__builtin_choose_expr(__safe_cmp(x, y), \
^~~~~~~~~~
../include/linux/kernel.h:879:19: note: in expansion of macro ‘__careful_cmp’
#define min(x, y) __careful_cmp(x, y, <)
^~~~~~~~~~~~~
../drivers/dma/imx-dma.c:288:8: note: in expansion of macro ‘min’
now = min(d->len, sg_dma_len(sg));
^~~
Rework so that we use min_t and pass in the size_t that returns the
minimum of two values, using the specified type.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d9140a0da4a230a03426d175145989667758aa6a upstream.
This commit fixes the issue that USB-DMAC hangs silently after system
resumes on R-Car Gen3 hence renesas_usbhs will not work correctly
when using USB-DMAC for bulk transfer e.g. ethernet or serial
gadgets.
The issue can be reproduced by these steps:
1. modprobe g_serial
2. Suspend and resume system.
3. connect a usb cable to host side
4. Transfer data from Host to Target
5. cat /dev/ttyGS0 (Target side)
6. echo "test" > /dev/ttyACM0 (Host side)
The 'cat' will not result anything. However, system still can work
normally.
Currently, USB-DMAC driver does not have system sleep callbacks hence
this driver relies on the PM core to force runtime suspend/resume to
suspend and reinitialize USB-DMAC during system resume. After
the commit 17218e0092f8 ("PM / genpd: Stop/start devices without
pm_runtime_force_suspend/resume()"), PM core will not force
runtime suspend/resume anymore so this issue happens.
To solve this, make system suspend resume explicit by using
pm_runtime_force_{suspend,resume}() as the system sleep callbacks.
SET_NOIRQ_SYSTEM_SLEEP_PM_OPS() is used to make sure USB-DMAC
suspended after and initialized before renesas_usbhs."
Signed-off-by: Phuong Nguyen <phuong.nguyen.xw@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
[shimoda: revise the commit log and add Cc tag]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- Fix in at_xdmac fr wrongful channel state
- Fix for imx driver for wrong callback invocation
- Fix to bcm driver for interrupt race & transaction abort.
- Fix in dmatest to abort in mapping error
* tag 'dmaengine-fix-5.0-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dmatest: Abort test in case of mapping error
dmaengine: bcm2835: Fix abort of transactions
dmaengine: bcm2835: Fix interrupt race on RT
dmaengine: imx-dma: fix wrong callback invoke
dmaengine: at_xdmac: Fix wrongfull report of a channel as in use
|
|
In case of mapping error the DMA addresses are invalid and continuing
will screw system memory or potentially something else.
[ 222.480310] dmatest: dma0chan7-copy0: summary 1 tests, 3 failures 6 iops 349 KB/s (0)
...
[ 240.912725] check: Corrupted low memory at 00000000c7c75ac9 (2940 phys) = 5656000000000000
[ 240.921998] check: Corrupted low memory at 000000005715a1cd (2948 phys) = 279f2aca5595ab2b
[ 240.931280] check: Corrupted low memory at 000000002f4024c0 (2950 phys) = 5e5624f349e793cf
...
Abort any test if mapping failed.
Fixes: 4076e755dbec ("dmatest: convert to dmaengine_unmap_data")
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
|
|
There are multiple issues with bcm2835_dma_abort() (which is called on
termination of a transaction):
* The algorithm to abort the transaction first pauses the channel by
clearing the ACTIVE flag in the CS register, then waits for the PAUSED
flag to clear. Page 49 of the spec documents the latter as follows:
"Indicates if the DMA is currently paused and not transferring data.
This will occur if the active bit has been cleared [...]"
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
So the function is entering an infinite loop because it is waiting for
PAUSED to clear which is always set due to the function having cleared
the ACTIVE flag. The only thing that's saving it from itself is the
upper bound of 10000 loop iterations.
The code comment says that the intention is to "wait for any current
AXI transfer to complete", so the author probably wanted to check the
WAITING_FOR_OUTSTANDING_WRITES flag instead. Amend the function
accordingly.
* The CS register is only read at the beginning of the function. It
needs to be read again after pausing the channel and before checking
for outstanding writes, otherwise writes which were issued between
the register read at the beginning of the function and pausing the
channel may not be waited for.
* The function seeks to abort the transfer by writing 0 to the NEXTCONBK
register and setting the ABORT and ACTIVE flags. Thereby, the 0 in
NEXTCONBK is sought to be loaded into the CONBLK_AD register. However
experimentation has shown this approach to not work: The CONBLK_AD
register remains the same as before and the CS register contains
0x00000030 (PAUSED | DREQ_STOPS_DMA). In other words, the control
block is not aborted but merely paused and it will be resumed once the
next DMA transaction is started. That is absolutely not the desired
behavior.
A simpler approach is to set the channel's RESET flag instead. This
reliably zeroes the NEXTCONBK as well as the CS register. It requires
less code and only a single MMIO write. This is also what popular
user space DMA drivers do, e.g.:
https://github.com/metachris/RPIO/blob/master/source/c_pwm/pwm.c
Note that the spec is contradictory whether the NEXTCONBK register
is writeable at all. On the one hand, page 41 claims:
"The value loaded into the NEXTCONBK register can be overwritten so
that the linked list of Control Block data structures can be
dynamically altered. However it is only safe to do this when the DMA
is paused."
On the other hand, page 40 specifies:
"Only three registers in each channel's register set are directly
writeable (CS, CONBLK_AD and DEBUG). The other registers (TI,
SOURCE_AD, DEST_AD, TXFR_LEN, STRIDE & NEXTCONBK), are automatically
loaded from a Control Block data structure held in external memory."
Fixes: 96286b576690 ("dmaengine: Add support for BCM2835")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.14+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Cc: Clive Messer <clive.m.messer@gmail.com>
Cc: Matthias Reichl <hias@horus.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is
enabled or "threadirqs" was passed on the command line) and if system
load is sufficiently high that wakeup latency of IRQ threads degrades,
SPI DMA transactions on the BCM2835 occasionally break like this:
ks8851 spi0.0: SPI transfer timed out
bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed
The root cause is an assumption made by the DMA driver which is
documented in a code comment in bcm2835_dma_terminate_all():
/*
* Stop DMA activity: we assume the callback will not be called
* after bcm_dma_abort() returns (even if it does, it will see
* c->desc is NULL and exit.)
*/
That assumption falls apart if the IRQ handler bcm2835_dma_callback() is
threaded: A client may terminate a descriptor and issue a new one
before the IRQ handler had a chance to run. In fact the IRQ handler may
miss an *arbitrary* number of descriptors. The result is the following
race condition:
1. A descriptor finishes, its interrupt is deferred to the IRQ thread.
2. A client calls dma_terminate_async() which sets channel->desc = NULL.
3. The client issues a new descriptor. Because channel->desc is NULL,
bcm2835_dma_issue_pending() immediately starts the descriptor.
4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS
register to acknowledge the interrupt. This clears the ACTIVE flag,
so the newly issued descriptor is paused in the middle of the
transaction. Because channel->desc is not NULL, the IRQ thread
finalizes the descriptor and tries to start the next one.
I see two possible solutions: The first is to call synchronize_irq()
in bcm2835_dma_issue_pending() to wait until the IRQ thread has
finished before issuing a new descriptor. The downside of this approach
is unnecessary latency if clients desire rapidly terminating and
re-issuing descriptors and don't have any use for an IRQ callback.
(The SPI TX DMA channel is a case in point.)
A better alternative is to make the IRQ thread recognize that it has
missed descriptors and avoid finalizing the newly issued descriptor.
So first of all, set the ACTIVE flag when acknowledging the interrupt.
This keeps a newly issued descriptor running.
If the descriptor was finished, the channel remains idle despite the
ACTIVE flag being set. However the ACTIVE flag can then no longer be
used to check whether the channel is idle, so instead check whether
the register containing the current control block address is zero
and finalize the current descriptor only if so.
That way, there is no impact on latency and throughput if the client
doesn't care for the interrupt: Only minimal additional overhead is
introduced for non-cyclic descriptors as one further MMIO read is
necessary per interrupt to check for idleness of the channel. Cyclic
descriptors are sped up slightly by removing one MMIO write per
interrupt.
Fixes: 96286b576690 ("dmaengine: Add support for BCM2835")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.14+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Meier <florian.meier@koalo.de>
Cc: Clive Messer <clive.m.messer@gmail.com>
Cc: Matthias Reichl <hias@horus.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Once the "ld_queue" list is not empty, next descriptor will migrate
into "ld_active" list. The "desc" variable will be overwritten
during that transition. And later the dmaengine_desc_get_callback_invoke()
will use it as an argument. As result we invoke wrong callback.
That behaviour was in place since:
commit fcaaba6c7136 ("dmaengine: imx-dma: fix callback path in tasklet").
But after commit 4cd13c21b207 ("softirq: Let ksoftirqd do its job")
things got worse, since possible delay between tasklet_schedule()
from DMA irq handler and actual tasklet function execution got bigger.
And that gave more time for new DMA request to be submitted and
to be put into "ld_queue" list.
It has been noticed that DMA issue is causing problems for "mxc-mmc"
driver. While stressing the system with heavy network traffic and
writing/reading to/from sd card simultaneously the timeout may happen:
10013000.sdhci: mxcmci_watchdog: read time out (status = 0x30004900)
That often lead to file system corruption.
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cc: stable@vger.kernel.org
|
|
atchan->status variable is used to store two different information:
- pass channel interrupts status from interrupt handler to tasklet;
- channel information like whether it is cyclic or paused;
This causes a bug when device_terminate_all() is called,
(AT_XDMAC_CHAN_IS_CYCLIC cleared on atchan->status) and then a late End
of Block interrupt arrives (AT_XDMAC_CIS_BIS), which sets bit 0 of
atchan->status. Bit 0 is also used for AT_XDMAC_CHAN_IS_CYCLIC, so when
a new descriptor for a cyclic transfer is created, the driver reports
the channel as in use:
if (test_and_set_bit(AT_XDMAC_CHAN_IS_CYCLIC, &atchan->status)) {
dev_err(chan2dev(chan), "channel currently used\n");
return NULL;
}
This patch fixes the bug by adding a different struct member to keep
the interrupts status separated from the channel status bits.
Fixes: e1f7c9eee707 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- Page table code for AMD IOMMU now supports large pages where smaller
page-sizes were mapped before. VFIO had to work around that in the
past and I included a patch to remove it (acked by Alex Williamson)
- Patches to unmodularize a couple of IOMMU drivers that would never
work as modules anyway.
- Work to unify the the iommu-related pointers in 'struct device' into
one pointer. This work is not finished yet, but will probably be in
the next cycle.
- NUMA aware allocation in iommu-dma code
- Support for r8a774a1 and r8a774c0 in the Renesas IOMMU driver
- Scalable mode support for the Intel VT-d driver
- PM runtime improvements for the ARM-SMMU driver
- Support for the QCOM-SMMUv2 IOMMU hardware from Qualcom
- Various smaller fixes and improvements
* tag 'iommu-updates-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (78 commits)
iommu: Check for iommu_ops == NULL in iommu_probe_device()
ACPI/IORT: Don't call iommu_ops->add_device directly
iommu/of: Don't call iommu_ops->add_device directly
iommu: Consolitate ->add/remove_device() calls
iommu/sysfs: Rename iommu_release_device()
dmaengine: sh: rcar-dmac: Use device_iommu_mapped()
xhci: Use device_iommu_mapped()
powerpc/iommu: Use device_iommu_mapped()
ACPI/IORT: Use device_iommu_mapped()
iommu/of: Use device_iommu_mapped()
driver core: Introduce device_iommu_mapped() function
iommu/tegra: Use helper functions to access dev->iommu_fwspec
iommu/qcom: Use helper functions to access dev->iommu_fwspec
iommu/of: Use helper functions to access dev->iommu_fwspec
iommu/mediatek: Use helper functions to access dev->iommu_fwspec
iommu/ipmmu-vmsa: Use helper functions to access dev->iommu_fwspec
iommu/dma: Use helper functions to access dev->iommu_fwspec
iommu/arm-smmu: Use helper functions to access dev->iommu_fwspec
ACPI/IORT: Use helper functions to access dev->iommu_fwspec
iommu: Introduce wrappers around dev->iommu_fwspec
...
|
|
Pull dmaengine updates from Vinod Koul:
"This includes a new driver, removes R-Mobile APE6 as it is no longer
used, sprd cyclic dma support, last batch of dma_slave_config
direction removal and random updates to bunch of drivers.
Summary:
- New driver for UniPhier MIO DMA controller
- Remove R-Mobile APE6 support
- Sprd driver updates and support for cyclic link-list
- Remove dma_slave_config direction usage from rest of drivers
- Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers"
* tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (48 commits)
dmaengine: qcom_hidma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: pxa: remove DBGFS_FUNC_DECL()
dmaengine: mic_x100_dma: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: amba-pl08x: convert to DEFINE_SHOW_ATTRIBUTE
dmaengine: Documentation: Add documentation for multi chan testing
dmaengine: dmatest: Add transfer_size parameter
dmaengine: dmatest: Add alignment parameter
dmaengine: dmatest: Use fixed point div to calculate iops
dmaengine: dmatest: Add support for multi channel testing
dmaengine: rcar-dmac: Document R8A774C0 bindings
dt-bindings: dmaengine: usb-dmac: Add binding for r8a774c0
dmaengine: zynqmp_dma: replace spin_lock_bh with spin_lock_irqsave
dmaengine: sprd: Add me as one of the module authors
dmaengine: sprd: Support DMA 2-stage transfer mode
dmaengine: sprd: Support DMA link-list cyclic callback
dmaengine: sprd: Set cur_desc as NULL when free or terminate one dma channel
dmaengine: sprd: Fix the last link-list configuration
dmaengine: sprd: Get transfer residue depending on the transfer direction
dmaengine: sprd: Remove direction usage from struct dma_slave_config
dmaengine: dmatest: fix a small memory leak in dmatest_func()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
'arm/omap', 'arm/smmu', 'x86/vt-d', 'x86/amd' and 'core' into next
|
|
Use Use device_iommu_mapped() to check if the device is
already mapped by an IOMMU.
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We already have the DEFINE_SHOW_ATTRIBUTE, There is no need to define
such a macro, so remove DBGFS_FUNC_DECL.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Existing transfer size "len" is either generated randomly or set to the
size of test_buf_size. In some cases we need to explicitly specify a
transfer size that is different from the buffer size and non aligned to
test the target device's ability to handle unaligned transfers.
This patch adds optional parameter "transfer_size" to allow setting
explicit transfer size for dma transfers.
Signed-off-by: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add parameter "alignment" to allow setting the address alignment
manually. Having the ability to configure address alignment from
user space adds new testing capabilities where different alignments can
be configured for testing without having to modify the dma device
alignment properties.
If configured, the alignment value will override the device alignment
property of the target device.
Signed-off-by: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use fixed point division to calculate iops to prevent reporting 0 iops
when operations last for longer than a second.
Signed-off-by: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for running tests on multiple channels simultaneously as the
driver currently limits to 1 channel per test run. This will add support
for stress testing DMA controllers with multi channel capabilities.
This is done by adding a callback function to the "channel" parameter
that registers the requested channel prior to the "run" parameter being
set to 1. Each time the "channel" parameter is populated with a new
dma channel, a new test is appended to the thread queue. Once the "run"
parameter is set to 1, the test will kick start all pending threads.
Signed-off-by: Seraj Alijan <seraj.alijan@sondrel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.
Fix this by partitioning it as 64 bytes per channel.
Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.
Fixes: 199244d69458 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
All device_prep_dma_* functions and device_issue_pending can be called
from an interrupt context. As this includes hard IRQs, we must use
spin_lock_irqsave() instead of spin_lock_bh() to access chan->lock.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add me as one of the module authors.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The Spreadtrum DMA controller supports channel 2-stage tansfer mode,
that means we can request 2 dma channels, one for source channel, and
another one for destination channel. Once the source channel's transaction
is done, it will trigger the destination channel's transaction automatically
by hardware signal.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The Spreadtrum DMA link-list mode is always one cyclic transfer,
so we should clear the SPRD_DMA_LLIST_END flag for the link-list
configuration. Moreover add cyclic callback support for the cyclic
transfer.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
It will be failed to start one new transfer if the channel started one
none interrupt transfer before, since we will only set the schan->cur_desc
as NULL depending on the transfer interrupt now. Thus we should set
schan->cur_desc as NULL when free or terminate one dma channel to
avoid this issue.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We will pass sglen as 0 configure the last link-list configuration
when filling the descriptor, which will cause the incorrect link-list
configuration. Thus we should check if the sglen is 0 to configure
the correct link-list configuration.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
