| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
LS1021A is a QorIQ SoC having little endian CAAM.
There are a few differences b/w QorIQ and i.MX from CAAM perspective:
1. i.MX platforms are somewhat special wrt. 64-bit registers:
-big endian format at 64-bit level: MSW at address+0 and LSW at address+4
-little endian format at 32-bit level (within MSW and LSW)
and thus need special handling.
2. No CCM (clock controller module) for QorIQ.
No CAAM clocks to enable / disable.
A new Kconfig option - CRYPTO_DEV_FSL_CAAM_LE - is added to indicate
CAAM is little endian (*). It is hidden from the user (to avoid
misconfiguration); when adding support for a new platform with LE CAAM,
either the Kconfig needs to be updated or the corresponding defconfig
needs to indicate that CAAM is LE.
(*) Using a DT property to provide CAAM endianness would not allow
for the ifdeffery.
In order to keep changes to a minimum, the following changes
are postponed:
-endianness fix of the last word in the S/G (rsvd2, bpid, offset),
fields are always 0 anyway;
-S/G format fix for i.MX7 (yes, i.MX7 support was not added yet,
but still...)
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Allow CAAM to be selected in the kernel for Freescale i.MX devices if
ARCH_MXC is enabled.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch fixes a number of problems in crypto driver Kconfig
entries:
1. Select BLKCIPHER instead of BLKCIPHER2. The latter is internal
and should not be used outside of the crypto API itself.
2. Do not select ALGAPI unless you use a legacy type like
CRYPTO_ALG_TYPE_CIPHER.
3. Select the algorithm type that you are implementing, e.g., AEAD.
4. Do not select generic C code such as CBC/ECB unless you use them
as a fallback.
5. Remove default n since that is the default default.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The SEC Job Rings are now available as individual devices.
This would enable sharing of job rings between kernel and
user space. Job Rings can now be dynamically bound/unbound
from kernel.
Changes are made in the following layers of CAAM Driver
1. Controller driver
- Does basic initialization of CAAM Block.
- Creates platform devices for Job Rings.
(Earlier the initialization of Job ring was done
by the controller driver)
2. JobRing Platform driver
- Manages the platform Job Ring devices created
by the controller driver
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds an option to the Kconfig file for
SEC which enables the user to see the debug messages
that are printed inside the SEC driver.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The Kconfig entry for CAAM's hash algorithm implementations has always
selected CRYPTO_AHASH. But there's no corresponding Kconfig symbol.
It seems it was intended to select CRYPTO_HASH, like other crypto
drivers do. That would apparently (indirectly) select CRYPTO_HASH2,
which would enable the ahash functionality this driver uses.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
It has been observed that in zero-loss benchmarks, when a
slow traffic rate is being tested, the IRQ timer coalescing
parameter was set too high, and the ethernet controller
would start dropping packets because the job ring back half
wouldn't be executed in time before the ethernet controller
would fill its buffers, thereby significantly reducing the
zero-loss performance figures.
Empirical testing has shown that the best zero-loss performance
is achieved when IRQ coalescing is set to minimum values and/or
turned off, since apparently the job ring driver already implements
an adequately-performing general-purpose IRQ mitigation strategy
in software.
Whilst we could go with minimal count (2-8) and timing settings
(192-256), we prefer just turning h/w coalescing altogether off
to minimize setkey latency (due to split key generation), and
for consistent cross-SoC performance (the SEC vs. core clock
ratio changes).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
caam_read copies random bytes from two buffers into output.
caam rng can fill empty buffer 0xffff bytes at a time,
but the buffer sizes are rounded down to multiple of cacheline size.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
caam supports ahash hmac with sha algorithms and md5.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of the SEC (talitos).
The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.
This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others. Only AEAD algorithms are implemented
at this time, for use with IPsec.
Many thanks to the Freescale STC team for their contributions
to this driver.
Signed-off-by: Steve Cornelius <sec@pobox.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
