| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit fa21e86caba2347e89eb65af926205a36a097c53 upstream.
When bt_en is pulled high by hardware, the host does not re-download
the firmware after SSR. The controller loads the rampatch and NVM
internally.
On HMT chip, the rampatch is ~264 KB and the NVM is ~9.4 KB. The
loading process takes approximately 70 ms. The previous 50 ms delay is
too short, causing the controller to not respond to the reset command
sent by the host, which leads to BT initialization failure:
Bluetooth: hci0: QCA memdump Done, received 458752, total 458752
Bluetooth: hci0: mem_dump_status: 2
Bluetooth: hci0: Opcode 0x0c03 failed: -110
Increase the delay to 100 ms, which was confirmed as a safe value by
the controller, to ensure the controller has finished loading the
firmware before the host sends commands.
Steps to reproduce:
1. Trigger SSR and wait for SSR to complete:
hcitool cmd 0x3f 0c 26
2. Run "bluetoothctl power on" and observe that BT fails to start.
Fixes: fce1a9244a0f ("Bluetooth: hci_qca: Fix SSR (SubSystem Restart) fail when BT_EN is pulled up by hw")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82855073c1081732656734b74d7d1d5e4cfd0da7 upstream.
The Bluetooth host decides whether to download firmware by reading the
controller firmware download completion flag and firmware version
information.
If a USB error occurs during the firmware download process (for example
due to a USB disconnect), the download is aborted immediately. An
incomplete firmware transfer does not cause the controller to set the
download completion flag, but the firmware version information may be
updated at an early stage of the download process.
In this case, after USB reconnection, the host attempts to re-download
the firmware because the download completion flag is not set. However,
since the controller reports the same firmware version as the target
firmware, the download is skipped. This ultimately results in the
firmware not being properly updated on the controller.
This change removes the restriction that skips firmware download when
the versions are equal. It covers scenarios where the USB connection
can be disconnected at any time and ensures that firmware download can
be retriggered after USB reconnection, allowing the Bluetooth firmware
to be correctly and completely updated.
Fixes: 3267c884cefa ("Bluetooth: btusb: Add support for QCA ROME chipset family")
Cc: stable@vger.kernel.org
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit dd1dda6b8d6e1f4376a5b3055a04f0ecbdb4d6bd ]
The setup_packet of control urb is not freed if usb_submit_urb fails or
the submitted urb is killed. Add free in these two paths.
Fixes: a1c49c434e150 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Signed-off-by: Jiajia Liu <liujiajia@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88365d04fdc821dc4e9eb0cc00fdf6905430d172 ]
btintel_pcie_get_mac_access() and btintel_pcie_release_mac_access()
were programming STOP_MAC_ACCESS_DIS and XTAL_CLK_REQ in addition to
the MAC_ACCESS_REQ handshake. These bits are not part of the host
MAC-access handshake on the supported parts; the driver was
programming them incorrectly. Drop the writes so the register update
contains only the bits the controller actually consumes.
Fixes: b9465e6670a2 ("Bluetooth: btintel_pcie: Read hardware exception data")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 375ba7484132662a4a8c7547d088fb6275c00282 upstream.
Since the timer uses jiffies as its unit rather than ms, the timeout value
must be converted from ms to jiffies when configuring the timer. Otherwise,
the intended 8s timeout is incorrectly set to approximately 33s.
To improve readability, embed msecs_to_jiffies() directly in the macro
definitions and drop the _MS suffix from macros that now yield jiffies
values: MEMDUMP_TIMEOUT, FW_DOWNLOAD_TIMEOUT, IBS_DISABLE_SSR_TIMEOUT,
CMD_TRANS_TIMEOUT, and IBS_BTSOC_TX_IDLE_TIMEOUT.
IBS_WAKE_RETRANS_TIMEOUT_MS and IBS_HOST_TX_IDLE_TIMEOUT_MS are
intentionally left unchanged. Their values are stored in the struct fields
wake_retrans and tx_idle_delay, which hold ms values at runtime and can be
modified via debugfs. The msecs_to_jiffies() conversion happens at each
call site against the field value, so it cannot be embedded in the macro.
Wake timer depends on commit c347ca17d62a
Cc: stable@vger.kernel.org
Fixes: d841502c79e3 ("Bluetooth: hci_qca: Collect controller memory dump during SSR")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1bb9336ae6b54a5f6a353c4bd4ed9a4307e429b upstream.
Vulnerabilities leading to Use-After-Free (UAF) and Null Pointer
Dereference (NPD) conditions were observed in the lifecycle management
of hci_uart.
The primary issue arises because the workqueues (init_ready and
write_work) are only flushed/cancelled if the HCI_UART_PROTO_READY
flag is set during TTY close. If a hangup occurs before setup completes,
hci_uart_tty_close() skips the teardown of these workqueues and
proceeds to free the `hu` struct. When the scheduled work executes
later, it blindly dereferences the freed `hu` struct.
Furthermore, several data races and UAFs were identified in the teardown
sequence:
1. Calling hci_uart_flush() from hci_uart_close() without effectively
disabling write_work causes a race condition where both can concurrently
double-free hu->tx_skb. This happens because protocol timers can
concurrently invoke hci_uart_tx_wakeup() and requeue write_work.
2. Calling hci_free_dev(hdev) before hu->proto->close(hu) causes a UAF
when vendor specific protocol close callbacks dereference hu->hdev.
3. In the initialization error paths, failing to take the proto_lock
write lock before clearing PROTO_READY leads to races with active
readers. Additionally, hci_uart_tty_receive() accesses hu->hdev
outside the read lock, leading to UAFs if the initialization error
path frees hdev concurrently.
Fix these synchronization and lifecycle issues by:
1. Re-ordering hci_uart_tty_close() to clear HCI_UART_PROTO_READY first,
followed immediately by a cancel_work_sync(&hu->write_work). Clearing
the flag locks out concurrent protocol timers from successfully invoking
hci_uart_tx_wakeup(), effectively rendering the cancellation permanent
and preventing the tx_skb double-free.
2. Note: Clearing PROTO_READY early causes hci_uart_close() to skip
hu->proto->flush(). This is perfectly safe in the tty_close path
because hu->proto->close() executes shortly after, which intrinsically
purges all protocol SKB queues and tears down the state.
3. Relocating hu->proto->close(hu) strictly prior to hci_free_dev(hdev)
across all close and error paths to prevent vendor-level UAFs.
4. Moving the hdev->stat.byte_rx increment in hci_uart_tty_receive()
inside the proto_lock read-side critical section to safely synchronize
with device unregistration.
5. Adding cancel_work_sync(&hu->write_work) to hci_uart_close() to safely
flush the workqueue before hci_uart_flush() is invoked via the HCI core.
6. Utilizing cancel_work_sync() instead of disable_work_sync() across
all paths to prevent permanently breaking user-space retry capabilities.
Fixes: 3b799254cf6f ("Bluetooth: hci_uart: Cancel init work before unregistering")
Cc: stable@vger.kernel.org
Signed-off-by: Mingyu Wang <25181214217@stu.xidian.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e3ac0d9f1a205f33a43fba3b79ef74d2f604c78b upstream.
MT7925 (USB ID 0e8d:e025) on fw version 20260106153314 sends WMT
FUNC_CTRL events that are missing the status field.
Prior to commit 006b9943b982 ("Bluetooth: btmtk: validate WMT event SKB
length before struct access") the status was read from out-of-bounds of
SKB data, which usually would result to success with
BTMTK_WMT_ON_UNDONE, although I don't know the intent here. The bounds
check added in that commit returns with error instead, producing
"Bluetooth: hci0: Failed to send wmt func ctrl (-22)" and makes the
device unusable.
Fix the regression by interpreting too short packet as status
BTMTK_WMT_ON_UNDONE, which makes the device work normally again.
Fixes: 634a4408c061 ("Bluetooth: btmtk: validate WMT event SKB length before struct access")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com> # MT7922 (0489:e0e2)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 68d39ea5e0adc9ecaea1ce8abd842ec972eb8718 ]
When hci_register_dev() fails in hci_uart_register_dev()
HCI_UART_PROTO_INIT is not cleared before calling hu->proto->close(hu)
and setting hu->hdev to NULL. This means incoming UART data will reach
the protocol-specific recv handler in hci_uart_tty_receive() after
resources are freed.
Clear HCI_UART_PROTO_INIT with a write lock before calling
hu->proto->close() and setting hu->hdev to NULL. The write lock ensures
all active readers have completed and no new reader can enter the
protocol recv path before resources are freed.
This allows the protocol-specific recv functions to remove the
"HCI_UART_REGISTERED" guard without risking a null pointer dereference
if hci_register_dev() fails.
Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization")
Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 634a4408c0615c523cf7531790f4f14a422b9206 upstream.
btmtk_usb_hci_wmt_sync() casts the WMT event response SKB data to
struct btmtk_hci_wmt_evt (7 bytes) and struct btmtk_hci_wmt_evt_funcc
(9 bytes) without first checking that the SKB contains enough data.
A short firmware response causes out-of-bounds reads from SKB tailroom.
Use skb_pull_data() to validate and advance past the base WMT event
header. For the FUNC_CTRL case, pull the additional status field bytes
before accessing them.
Fixes: d019930b0049 ("Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c")
Cc: stable@vger.kernel.org
Signed-off-by: Tristan Madani <tristan@talencesecurity.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit daf23014e5d975e72ea9c02b5160d3fcf070ea47 upstream.
virtbt_rx_handle() reads the leading pkt_type byte from the RX skb
and forwards the remainder to hci_recv_frame() for every
event/ACL/SCO/ISO type, without checking that the remaining payload
is at least the fixed HCI header for that type.
After the preceding patch bounds the backend-supplied used.len to
[1, VIRTBT_RX_BUF_SIZE], a one-byte completion still reaches
hci_recv_frame() with skb->len already pulled to 0. If the byte
happened to be HCI_ACLDATA_PKT, the ACL-vs-ISO classification
fast-path in hci_dev_classify_pkt_type() dereferences
hci_acl_hdr(skb)->handle whenever the HCI device has an active
CIS_LINK, BIS_LINK, or PA_LINK connection, reading two bytes of
uninitialized RX-buffer data. The same hazard exists for every
packet type the driver accepts because none of the switch cases in
virtbt_rx_handle() check skb->len against the per-type minimum HCI
header size before handing the frame to the core.
After stripping pkt_type, require skb->len to cover the fixed
header size for the selected type (event 2, ACL 4, SCO 3, ISO 4)
before calling hci_recv_frame(); drop ratelimited otherwise.
Unknown pkt_type values still take the original kfree_skb() default
path.
Use bt_dev_err_ratelimited() because both the length and pkt_type
values come from an untrusted backend that can otherwise flood the
kernel log.
Fixes: 160fbcf3bfb9 ("Bluetooth: virtio_bt: Use skb_put to set length")
Cc: stable@vger.kernel.org
Cc: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21bd244b6de5d2fe1063c23acc93fbdd2b20d112 upstream.
virtbt_rx_work() calls skb_put(skb, len) where len comes directly
from virtqueue_get_buf() with no validation against the buffer we
posted to the device. The RX skb is allocated in virtbt_add_inbuf()
and exposed to virtio as exactly 1000 bytes via sg_init_one().
Checking len against skb_tailroom(skb) is not sufficient because
alloc_skb() can leave more tailroom than the 1000 bytes actually
handed to the device. A malicious or buggy backend can therefore
report used.len between 1001 and skb_tailroom(skb), causing skb_put()
to include uninitialized kernel heap bytes that were never written by
the device.
The same path also accepts len == 0, in which case skb_put(skb, 0)
leaves the skb empty but virtbt_rx_handle() still reads the pkt_type
byte from skb->data, consuming uninitialized memory.
Define VIRTBT_RX_BUF_SIZE once and reuse it in alloc_skb() and
sg_init_one(), and gate virtbt_rx_work() on that same constant so
the bound checked matches the buffer actually exposed to the device.
Reject used.len == 0 in the same gate so an empty completion can
no longer reach virtbt_rx_handle().
Use bt_dev_err_ratelimited() because the length value comes from an
untrusted backend that can otherwise flood the kernel log.
Same class of bug as commit c04db81cd028 ("net/9p: Fix buffer
overflow in USB transport layer"), which hardened the USB 9p
transport against unchecked device-reported length.
Fixes: 160fbcf3bfb9 ("Bluetooth: virtio_bt: Use skb_put to set length")
Cc: stable@vger.kernel.org
Cc: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during
initialization") fixed a race for hci commands sent during initialization.
However, there is still a race that happens if an hci event from one of
these commands is received before HCI_UART_REGISTERED has been set at
the end of hci_uart_register_dev(). The event will be ignored which
causes the command to fail with a timeout in the log:
"Bluetooth: hci0: command 0x1003 tx timeout"
This is because the hci event receive path (hci_uart_tty_receive ->
h4_recv) requires HCI_UART_REGISTERED to be set in h4_recv(), while the
hci command transmit path (hci_uart_send_frame -> h4_enqueue) only
requires HCI_UART_PROTO_INIT to be set in hci_uart_send_frame().
The check for HCI_UART_REGISTERED was originally added in commit
c2578202919a ("Bluetooth: Fix H4 crash from incoming UART packets")
to fix a crash caused by hu->hdev being null dereferenced. That can no
longer happen: once HCI_UART_PROTO_INIT is set in hci_uart_register_dev()
all pointers (hu, hu->priv and hu->hdev) are valid, and
hci_uart_tty_receive() already calls h4_recv() on HCI_UART_PROTO_INIT
or HCI_UART_PROTO_READY.
Remove the check for HCI_UART_REGISTERED in h4_recv() to fix the race
condition.
Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization")
Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btusb_work() maps the number of active SCO links to USB alternate
settings through a three-entry lookup table when CVSD traffic uses
transparent voice settings. The lookup currently indexes alts[] with
data->sco_num - 1 without first constraining sco_num to the number of
available table entries.
While the table only defines alternate settings for up to three SCO
links, data->sco_num comes from hci_conn_num() and is used directly.
Cap the lookup to the last table entry before indexing it so the
driver keeps selecting the highest supported alternate setting without
reading past alts[].
Fixes: baac6276c0a9 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints")
Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET
and Intel exception-info retrieval) without holding
hci_req_sync_lock(). This lets it race against
hci_dev_do_close() -> btintel_shutdown_combined(), which also runs
__hci_cmd_sync() under the same lock. When both paths manipulate
hdev->req_status/req_rsp concurrently, the close path may free the
response skb first, and the still-running hw_error path hits a
slab-use-after-free in kfree_skb().
Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it
is serialized with every other synchronous HCI command issuer.
Below is the data race report and the kasan report:
BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined
read of hdev->req_rsp at net/bluetooth/hci_sync.c:199
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254
hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030
write/free by task ioctl/22580:
btintel_shutdown_combined+0xd0/0x360
drivers/bluetooth/btintel.c:3648
hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246
hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526
BUG: KASAN: slab-use-after-free in
sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202
Read of size 4 at addr ffff888144a738dc
by task kworker/u17:1/83:
__hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200
__hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223
btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260
Fixes: 973bb97e5aee ("Bluetooth: btintel: Add generic function for handling hardware errors")
Signed-off-by: Cen Zhang <zzzccc427@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Smatch reports:
drivers/bluetooth/hci_ll.c:587 download_firmware() warn:
'fw' from request_firmware() not released on lines: 544.
In download_firmware(), if request_firmware() succeeds but the returned
firmware content is invalid (no data or zero size), the function returns
without releasing the firmware, resulting in a resource leak.
Fix this by calling release_firmware() before returning when
request_firmware() succeeded but the firmware content is invalid.
Fixes: 371805522f87 ("bluetooth: hci_uart: add LL protocol serdev driver support")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Anas Iqbal <mohd.abd.6602@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
WCN3998 uses a bit different format for rom version:
[ 5.479978] Bluetooth: hci0: setting up wcn399x
[ 5.633763] Bluetooth: hci0: QCA Product ID :0x0000000a
[ 5.645350] Bluetooth: hci0: QCA SOC Version :0x40010224
[ 5.650906] Bluetooth: hci0: QCA ROM Version :0x00001001
[ 5.665173] Bluetooth: hci0: QCA Patch Version:0x00006699
[ 5.679356] Bluetooth: hci0: QCA controller version 0x02241001
[ 5.691109] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
[ 6.680102] Bluetooth: hci0: QCA Downloading qca/crnv21.bin
[ 6.842948] Bluetooth: hci0: QCA setup on UART is completed
Fixes: 523760b7ff88 ("Bluetooth: hci_qca: Added support for WCN3998")
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from IPsec, Bluetooth and netfilter
Current release - regressions:
- wifi: fix dev_alloc_name() return value check
- rds: fix recursive lock in rds_tcp_conn_slots_available
Current release - new code bugs:
- vsock: lock down child_ns_mode as write-once
Previous releases - regressions:
- core:
- do not pass flow_id to set_rps_cpu()
- consume xmit errors of GSO frames
- netconsole: avoid OOB reads, msg is not nul-terminated
- netfilter: h323: fix OOB read in decode_choice()
- tcp: re-enable acceptance of FIN packets when RWIN is 0
- udplite: fix null-ptr-deref in __udp_enqueue_schedule_skb().
- wifi: brcmfmac: fix potential kernel oops when probe fails
- phy: register phy led_triggers during probe to avoid AB-BA deadlock
- eth:
- bnxt_en: fix deleting of Ntuple filters
- wan: farsync: fix use-after-free bugs caused by unfinished tasklets
- xscale: check for PTP support properly
Previous releases - always broken:
- tcp: fix potential race in tcp_v6_syn_recv_sock()
- kcm: fix zero-frag skb in frag_list on partial sendmsg error
- xfrm:
- fix race condition in espintcp_close()
- always flush state and policy upon NETDEV_UNREGISTER event
- bluetooth:
- purge error queues in socket destructors
- fix response to L2CAP_ECRED_CONN_REQ
- eth:
- mlx5:
- fix circular locking dependency in dump
- fix "scheduling while atomic" in IPsec MAC address query
- gve: fix incorrect buffer cleanup for QPL
- team: avoid NETDEV_CHANGEMTU event when unregistering slave
- usb: validate USB endpoints"
* tag 'net-7.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
netfilter: nf_conntrack_h323: fix OOB read in decode_choice()
dpaa2-switch: validate num_ifs to prevent out-of-bounds write
net: consume xmit errors of GSO frames
vsock: document write-once behavior of the child_ns_mode sysctl
vsock: lock down child_ns_mode as write-once
selftests/vsock: change tests to respect write-once child ns mode
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
net/mlx5: Fix missing devlink lock in SRIOV enable error path
net/mlx5: E-switch, Clear legacy flag when moving to switchdev
net/mlx5: LAG, disable MPESW in lag_disable_change()
net/mlx5: DR, Fix circular locking dependency in dump
selftests: team: Add a reference count leak test
team: avoid NETDEV_CHANGEMTU event when unregistering slave
net: mana: Fix double destroy_workqueue on service rescan PCI path
MAINTAINERS: Update maintainer entry for QUALCOMM ETHQOS ETHERNET DRIVER
dpll: zl3073x: Remove redundant cleanup in devm_dpll_init()
selftests/net: packetdrill: Verify acceptance of FIN packets when RWIN is 0
tcp: re-enable acceptance of FIN packets when RWIN is 0
vsock: Use container_of() to get net namespace in sysctl handlers
net: usb: kaweth: validate USB endpoints
...
|
|
The setup process previously combined error handling and retry gating
under one condition. As a result, the final failed attempt exited
without performing cleanup.
Update the failure path to always perform power and port cleanup on
setup failure, and reopen the port only when retrying.
Fixes: 9e80587aba4c ("Bluetooth: hci_qca: Enhance retry logic in qca_setup")
Signed-off-by: Jinwang Li <jinwang.li@oss.qualcomm.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This was done entirely with mindless brute force, using
git grep -l '\<k[vmz]*alloc_objs*(.*, GFP_KERNEL)' |
xargs sed -i 's/\(alloc_objs*(.*\), GFP_KERNEL)/\1)/'
to convert the new alloc_obj() users that had a simple GFP_KERNEL
argument to just drop that argument.
Note that due to the extreme simplicity of the scripting, any slightly
more complex cases spread over multiple lines would not be triggered:
they definitely exist, but this covers the vast bulk of the cases, and
the resulting diff is also then easier to check automatically.
For the same reason the 'flex' versions will be done as a separate
conversion.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is the result of running the Coccinelle script from
scripts/coccinelle/api/kmalloc_objs.cocci. The script is designed to
avoid scalar types (which need careful case-by-case checking), and
instead replace kmalloc-family calls that allocate struct or union
object instances:
Single allocations: kmalloc(sizeof(TYPE), ...)
are replaced with: kmalloc_obj(TYPE, ...)
Array allocations: kmalloc_array(COUNT, sizeof(TYPE), ...)
are replaced with: kmalloc_objs(TYPE, COUNT, ...)
Flex array allocations: kmalloc(struct_size(PTR, FAM, COUNT), ...)
are replaced with: kmalloc_flex(*PTR, FAM, COUNT, ...)
(where TYPE may also be *VAR)
The resulting allocations no longer return "void *", instead returning
"TYPE *".
Signed-off-by: Kees Cook <kees@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the small amount of tty and serial driver updates for 7.0-rc1.
Nothing major in here at all, just some driver updates and minor
tweaks and cleanups including:
- sh-sci serial driver updates
- 8250 driver updates
- attempt to make the tty ports have their own workqueue, but was
reverted after testing found it to have problems on some platforms.
This will probably come back for 7.1 after it has been reworked and
resubmitted
- other tiny tty driver changes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (49 commits)
Revert "tty: tty_port: add workqueue to flip TTY buffer"
tty: tty_port: add workqueue to flip TTY buffer
serial: 8250_pci: Remove custom deprecated baud setting routine
serial: 8250_omap: Remove custom deprecated baud setting routine
dt-bindings: serial: renesas,scif: Document RZ/G3L SoC
serial: 8250: omap: set out-of-band wakeup if wakeup pinctrl exists
tty: hvc-iucv: Remove KMSG_COMPONENT macro
dt-bindings: serial: google,goldfish-tty: Convert to DT schema
dt-bindings: serial: sh-sci: Fold single-entry compatibles into enum
serial: 8250: 8250_omap.c: Clear DMA RX running status only after DMA termination is done
serial: 8250: 8250_omap.c: Add support for handling UART error conditions
serial: SH_SCI: improve "DMA support" prompt
serial: Kconfig: fix ordering of entries for menu display
serial: 8250: fix ordering of entries for menu display
serial: imx: change SERIAL_IMX_CONSOLE to bool
8250_men_mcb: drop unneeded MODULE_ALIAS
serial: men_z135_uart: drop unneeded MODULE_ALIAS
dt-bindings: serial: renesas,rsci: Document RZ/V2H(P) and RZ/V2N SoCs
serial: rsci: Convert to FIELD_MODIFY()
dt-bindings: serial: 8250: add SpacemiT K3 UART compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core & protocols:
- A significant effort all around the stack to guide the compiler to
make the right choice when inlining code, to avoid unneeded calls
for small helper and stack canary overhead in the fast-path.
This generates better and faster code with very small or no text
size increases, as in many cases the call generated more code than
the actual inlined helper.
- Extend AccECN implementation so that is now functionally complete,
also allow the user-space enabling it on a per network namespace
basis.
- Add support for memory providers with large (above 4K) rx buffer.
Paired with hw-gro, larger rx buffer sizes reduce the number of
buffers traversing the stack, dincreasing single stream CPU usage
by up to ~30%.
- Do not add HBH header to Big TCP GSO packets. This simplifies the
RX path, the TX path and the NIC drivers, and is possible because
user-space taps can now interpret correctly such packets without
the HBH hint.
- Allow IPv6 routes to be configured with a gateway address that is
resolved out of a different interface than the one specified,
aligning IPv6 to IPv4 behavior.
- Multi-queue aware sch_cake. This makes it possible to scale the
rate shaper of sch_cake across multiple CPUs, while still enforcing
a single global rate on the interface.
- Add support for the nbcon (new buffer console) infrastructure to
netconsole, enabling lock-free, priority-based console operations
that are safer in crash scenarios.
- Improve the TCP ipv6 output path to cache the flow information,
saving cpu cycles, reducing cache line misses and stack use.
- Improve netfilter packet tracker to resolve clashes for most
protocols, avoiding unneeded drops on rare occasions.
- Add IP6IP6 tunneling acceleration to the flowtable infrastructure.
- Reduce tcp socket size by one cache line.
- Notify neighbour changes atomically, avoiding inconsistencies
between the notification sequence and the actual states sequence.
- Add vsock namespace support, allowing complete isolation of vsocks
across different network namespaces.
- Improve xsk generic performances with cache-alignment-oriented
optimizations.
- Support netconsole automatic target recovery, allowing netconsole
to reestablish targets when underlying low-level interface comes
back online.
Driver API:
- Support for switching the working mode (automatic vs manual) of a
DPLL device via netlink.
- Introduce PHY ports representation to expose multiple front-facing
media ports over a single MAC.
- Introduce "rx-polarity" and "tx-polarity" device tree properties,
to generalize polarity inversion requirements for differential
signaling.
- Add helper to create, prepare and enable managed clocks.
Device drivers:
- Add Huawei hinic3 PF etherner driver.
- Add DWMAC glue driver for Motorcomm YT6801 PCIe ethernet
controller.
- Add ethernet driver for MaxLinear MxL862xx switches
- Remove parallel-port Ethernet driver.
- Convert existing driver timestamp configuration reporting to
hwtstamp_get and remove legacy ioctl().
- Convert existing drivers to .get_rx_ring_count(), simplifing the RX
ring count retrieval. Also remove the legacy fallback path.
- Ethernet high-speed NICs:
- Broadcom (bnxt, bng):
- bnxt: add FW interface update to support FEC stats histogram
and NVRAM defragmentation
- bng: add TSO and H/W GRO support
- nVidia/Mellanox (mlx5):
- improve latency of channel restart operations, reducing the
used H/W resources
- add TSO support for UDP over GRE over VLAN
- add flow counters support for hardware steering (HWS) rules
- use a static memory area to store headers for H/W GRO,
leading to 12% RX tput improvement
- Intel (100G, ice, idpf):
- ice: reorganizes layout of Tx and Rx rings for cacheline
locality and utilizes __cacheline_group* macros on the new
layouts
- ice: introduces Synchronous Ethernet (SyncE) support
- Meta (fbnic):
- adds debugfs for firmware mailbox and tx/rx rings vectors
- Ethernet virtual:
- geneve: introduce GRO/GSO support for double UDP encapsulation
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- some code refactoring and cleanups
- RealTek (r8169):
- add support for RTL8127ATF (10G Fiber SFP)
- add dash and LTR support
- Airoha:
- AN8811HB 2.5 Gbps phy support
- Freescale (fec):
- add XDP zero-copy support
- Thunderbolt:
- add get link setting support to allow bonding
- Renesas:
- add support for RZ/G3L GBETH SoC
- Ethernet switches:
- Maxlinear:
- support R(G)MII slow rate configuration
- add support for Intel GSW150
- Motorcomm (yt921x):
- add DCB/QoS support
- TI:
- icssm-prueth: support bridging (STP/RSTP) via the switchdev
framework
- Ethernet PHYs:
- Realtek:
- enable SGMII and 2500Base-X in-band auto-negotiation
- simplify and reunify C22/C45 drivers
- Micrel: convert bindings to DT schema
- CAN:
- move skb headroom content into skb extensions, making CAN
metadata access more robust
- CAN drivers:
- rcar_canfd:
- add support for FD-only mode
- add support for the RZ/T2H SoC
- sja1000: cleanup the CAN state handling
- WiFi:
- implement EPPKE/802.1X over auth frames support
- split up drop reasons better, removing generic RX_DROP
- additional FTM capabilities: 6 GHz support, supported number of
spatial streams and supported number of LTF repetitions
- better mac80211 iterators to enumerate resources
- initial UHR (Wi-Fi 8) support for cfg80211/mac80211
- WiFi drivers:
- Qualcomm/Atheros:
- ath11k: support for Channel Frequency Response measurement
- ath12k: a significant driver refactor to support multi-wiphy
devices and and pave the way for future device support in the
same driver (rather than splitting to ath13k)
- ath12k: support for the QCC2072 chipset
- Intel:
- iwlwifi: partial Neighbor Awareness Networking (NAN) support
- iwlwifi: initial support for U-NII-9 and IEEE 802.11bn
- RealTek (rtw89):
- preparations for RTL8922DE support
- Bluetooth:
- implement setsockopt(BT_PHY) to set the connection packet type/PHY
- set link_policy on incoming ACL connections
- Bluetooth drivers:
- btusb: add support for MediaTek7920, Realtek RTL8761BU and 8851BE
- btqca: add WCN6855 firmware priority selection feature"
* tag 'net-next-7.0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1254 commits)
bnge/bng_re: Add a new HSI
net: macb: Fix tx/rx malfunction after phy link down and up
af_unix: Fix memleak of newsk in unix_stream_connect().
net: ti: icssg-prueth: Add optional dependency on HSR
net: dsa: add basic initial driver for MxL862xx switches
net: mdio: add unlocked mdiodev C45 bus accessors
net: dsa: add tag format for MxL862xx switches
dt-bindings: net: dsa: add MaxLinear MxL862xx
selftests: drivers: net: hw: Modify toeplitz.c to poll for packets
octeontx2-pf: Unregister devlink on probe failure
net: renesas: rswitch: fix forwarding offload statemachine
ionic: Rate limit unknown xcvr type messages
tcp: inet6_csk_xmit() optimization
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_syn_recv_sock()
tcp: populate inet->cork.fl.u.ip6 in tcp_v6_connect()
ipv6: inet6_csk_xmit() and inet6_csk_update_pmtu() use inet->cork.fl.u.ip6
ipv6: use inet->cork.fl.u.ip6 and np->final in ip6_datagram_dst_update()
ipv6: use np->final in inet6_sk_rebuild_header()
ipv6: add daddr/final storage in struct ipv6_pinfo
net: stmmac: qcom-ethqos: fix qcom_ethqos_serdes_powerup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq cleanups from Thomas Gleixner:
"A series of treewide cleanups to ensure interrupt request consistency.
- Add the missing IRQF_COND_ONESHOT flag to devm_request_irq()
This is inconsistent vs request_irq() and causes the same issues
which where addressed with the introduction of this flag
- Cleanup IRQF_ONESHOT and IRQF_NO_THREAD usage
Quite some drivers have inconsistent interrupt request flags
related to interrupt threading namely IRQF_ONESHOT and
IRQF_NO_THREAD. This leads to warnings and/or malfunction when
forced interrupt threading is enabled.
- Remove stub primary (hard interrupt) handlers
A bunch of drivers implement a stub primary (hard interrupt)
handler which just returns IRQ_WAKE_THREAD. The same functionality
is provided by the core code when the primary handler argument of
request_thread_irq() is set to NULL"
* tag 'irq-cleanups-2026-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
media: pci: mg4b: Use IRQF_NO_THREAD
mfd: wm8350-core: Use IRQF_ONESHOT
thermal/qcom/lmh: Replace IRQF_ONESHOT with IRQF_NO_THREAD
rtc: amlogic-a4: Remove IRQF_ONESHOT
usb: typec: fusb302: Remove IRQF_ONESHOT
EDAC/altera: Remove IRQF_ONESHOT
char: tpm: cr50: Remove IRQF_ONESHOT
ARM: versatile: Remove IRQF_ONESHOT
scsi: efct: Use IRQF_ONESHOT and default primary handler
Bluetooth: btintel_pcie: Use IRQF_ONESHOT and default primary handler
bus: fsl-mc: Use default primary handler
mailbox: bcm-ferxrm-mailbox: Use default primary handler
iommu/amd: Use core's primary handler and set IRQF_ONESHOT
platform/x86: int0002: Remove IRQF_ONESHOT from request_irq()
genirq: Set IRQF_COND_ONESHOT in devm_request_irq().
|
|
There is no added value in btintel_pcie_msix_isr() compared to
irq_default_primary_handler().
Using a threaded interrupt without a dedicated primary handler mandates
the IRQF_ONESHOT flag to mask the interrupt source while the threaded
handler is active. Otherwise the interrupt can fire again before the
threaded handler had a chance to run.
Use the default primary interrupt handler by specifying NULL and set
IRQF_ONESHOT so the interrupt source is masked until the secondary
handler is done.
Fixes: c2b636b3f788d ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@kernel.org>
Link: https://patch.msgid.link/20260128095540.863589-7-bigeasy@linutronix.de
|
|
Add QCA_CAP_HFP_HW_OFFLOAD capability flag to WCN6855 and WCN7850
device data structures to enable Hands-Free Profile (HFP) hardware
offload support on these Qualcomm Bluetooth chipsets.
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Replace SoC-specific check with capability-based approach for HFP
hardware offload configuration. Add QCA_CAP_HFP_HW_OFFLOAD capability
flag and support_hfp_hw_offload field to qca_serdev structure. Add
QCA_CAP_HFP_HW_OFFLOAD capability flag to QCA2066 device data
structures.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Mengshi Wu <mengshi.wu@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB ID 7392:e611 for Edimax EW-7611UXB which is RTL8851BU-based
Wi-Fi + Bluetooth adapter.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=7392 ProdID=e611 Rev= 0.00
S: Manufacturer=Realtek
S: Product=802.11ax WLAN Adapter
S: SerialNumber=00e04c000001
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu_git
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Cc: stable@vger.kernel.org # 6.6.x
Signed-off-by: Zenm Chen <zenmchen@gmail.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled.
Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization")
Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/
Signed-off-by: Jia-Hong Su <s11242586@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The USB device ID 0x13d3/0x3618 is listed twice in the device table.
Remove the duplicate entry and keep the one under the correct
"Realtek 8852BT/8852BE-VT Bluetooth devices" section.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek
RTL8761BU Bluetooth adapter.
Reference:
https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth
Signed-off-by: Jacopo Scannella <code@charlie.cat>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The functions are already disabled if CONFIG_PM or CONFIG_PM_SLEEP are
disabled through the use of SET_SYSTEM_SLEEP_PM_OPS() and
SET_RUNTIME_PM_OPS().
This increases build coverage and allows to drop a few #ifdef's.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The functions are already disabled through the use of pm_ptr() when
CONFIG_PM is disabled, and will be removed from the final linked code
as not needed.
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID:PID 13d3:3612 to the quirks_table.
This ID pair is found in the Realtek RTL8852CE PCIe module
in an ASUS TUF A14 2025 (FA401KM) laptop.
Tested on aforementioned laptop.
The device info from /sys/kernel/debug/usb/devices is listed as below.
T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3612 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Shell Chen <w27@sorz.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The kfree_skb() function internally checks if the skb is NULL,
so an explicit check before calling it is redundant and can be removed.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If USB autosuspend occurs while discovery is active, the ongoing
HCI operation may not complete successfully. On some devices, this
can leave discovery.state stuck in DISCOVERY_FINDING.
Signed-off-by: Linmao Li <lilinmao@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add USB ID 0489:e112 for the Realtek 8851BE Bluetooth adapter.
Without this entry, the device is not handled correctly by btusb and Bluetooth fails to initialise.
Adding the ID enables proper Realtek initialization for Bluetooth to work on various motherboards using this Bluetooth adapter.
The device identifies as:
Bus 001 Device XXX: ID 0489:e112 Foxconn / Hon Hai Bluetooth Radio
Tested on Realtek 8851BE. Bluetooth works after this change is made.
Signed-off-by: Techie Ernie <techieernie@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Historically, WCN685x and QCA2066 shared the same firmware files.
Now, changes are planned for the firmware that will make it incompatible
with QCA2066, so a new firmware name is required for WCN685x.
Test Steps:
- Boot device
- Check the BTFW loading status via dmesg
Sanity pass and Test Log:
QCA Downloading qca/wcnhpbftfw21.tlv
Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
QCA Downloading qca/hpbftfw21.tlv
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
WCN7850 will first attempt to use ELF_TYPE_PATCH,
and if that fails, it will fall back to TLV_TYPE_PATCH.
To code uniformity, move WCN7850 workaround to the caller.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This increases build coverage and allows to drop an #ifdef.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Switch to the generic PCI power management framework and remove legacy
callbacks like .suspend() and .resume(). With the generic framework, the
standard PCI related work like:
- pci_save/restore_state()
- pci_enable/disable_device()
- pci_set_power_state()
is handled by the PCI core and this driver should implement only
hci_bcm4377 specific operations in its respective callback functions.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add support for MediaTek7920 0489:e158
/sys/kernel/debug/usb/devices reports for that device:
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e158 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Andrew Elatsev <elantsew.andrew@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
by hw
On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw
and cannot be controlled by the host. As a result, in case of a firmware
crash, the host cannot trigger a cold reset. Instead, the BT controller
performs a warm restart on its own, without reloading the firmware.
This leads to the controller remaining in IBS_WAKE state, while the host
expects it to be in sleep mode. The mismatch causes HCI reset commands
to time out. Additionally, the driver does not clear internal flags
QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence.
If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode
due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag
is not cleared, so only the first SSR generates a coredump.
Tell the driver that the BT controller has undergone a proper restart sequence:
- Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR.
- Add a 50ms delay to allow the controller to complete its warm reset.
- Reset tx_idle_timer to prevent the host from entering TX sleep mode.
- Clear memcoredump_flag to allow multiple coredump captures.
Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set,
which indicates that BT_EN is defined in DTS and cannot be toggled.
Refer to the comment in include/net/bluetooth/hci.h for details on
HCI_QUIRK_NON_PERSISTENT_SETUP.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling
hci_uart_register_dev(), which calls proto->open() to initialize
hu->priv. However, if a TTY write wakeup occurs during this window,
hci_uart_tx_wakeup() may schedule write_work before hu->priv is
initialized, leading to a NULL pointer dereference in
hci_uart_write_work() when proto->dequeue() accesses hu->priv.
The race condition is:
CPU0 CPU1
---- ----
hci_uart_set_proto()
set_bit(HCI_UART_PROTO_INIT)
hci_uart_register_dev()
tty write wakeup
hci_uart_tty_wakeup()
hci_uart_tx_wakeup()
schedule_work(&hu->write_work)
proto->open(hu)
// initializes hu->priv
hci_uart_write_work()
hci_uart_dequeue()
proto->dequeue(hu)
// accesses hu->priv (NULL!)
Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open()
succeeds, ensuring hu->priv is initialized before any work can be
scheduled.
Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization")
Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/
Signed-off-by: Jia-Hong Su <s11242586@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This reverts commit 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in
btusb.c file").
In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This
ties the lifetime of all the btusb data to the binding of a driver to
one interface, INTF. In a driver that binds to other interfaces, ISOC
and DIAG, this is an accident waiting to happen.
The issue is revealed in btusb_disconnect(), where calling
usb_driver_release_interface(&btusb_driver, data->intf) will have devm
free the data that is also being used by the other interfaces of the
driver that may not be released yet.
To fix this, revert the use of devm and go back to freeing memory
explicitly.
Fixes: 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This saves a cast in the driver. The motivation is stop using the callback
.shutdown in qca_serdev_driver.driver to make it possible to drop that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/261a3384e25c4837d4efee87958805f15d7d4e3c.1765526117.git.u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This saves a cast in the driver. The motivation is stop using the callback
.shutdown in qca_serdev_driver.driver to make it possible to drop that.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/42ae20ba70ff6fbbbd9b846ac9acd0f7d58451b0.1765526117.git.u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add VID 13d3 & PID 3533 for Realtek RTL8821CE USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3533 Rev= 1.10
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Gongwei Li <ligongwei@kylinos.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Replace the open-coded multiplication in kmalloc() with a call
to kmalloc_array() to prevent potential integer overflows.
This is a mechanical change, replacing BCM_FW_NAME_LEN with
the type-safe sizeof(*fw_name) as the element size
Signed-off-by: Ayaan Mirza Baig <ayaanmirzabaig85@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch adds the infrastructure that allow the user space program to
talk to intel pcie driver directly for fetching basic driver details.
The changes introduced are referred form
commit 04425292a62c15 ("Bluetooth: Introduce HCI Driver protocol")
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
