summaryrefslogtreecommitdiff
path: root/drivers/bluetooth
AgeCommit message (Collapse)AuthorFilesLines
3 daysBluetooth: hci_h4: Fix race during initializationJonathan Rissanen1-3/+0
[ Upstream commit 0ffac654e95c1bdfe2d4edf28fb18d6ba1f103e6 ] Commit 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") fixed a race for hci commands sent during initialization. However, there is still a race that happens if an hci event from one of these commands is received before HCI_UART_REGISTERED has been set at the end of hci_uart_register_dev(). The event will be ignored which causes the command to fail with a timeout in the log: "Bluetooth: hci0: command 0x1003 tx timeout" This is because the hci event receive path (hci_uart_tty_receive -> h4_recv) requires HCI_UART_REGISTERED to be set in h4_recv(), while the hci command transmit path (hci_uart_send_frame -> h4_enqueue) only requires HCI_UART_PROTO_INIT to be set in hci_uart_send_frame(). The check for HCI_UART_REGISTERED was originally added in commit c2578202919a ("Bluetooth: Fix H4 crash from incoming UART packets") to fix a crash caused by hu->hdev being null dereferenced. That can no longer happen: once HCI_UART_PROTO_INIT is set in hci_uart_register_dev() all pointers (hu, hu->priv and hu->hdev) are valid, and hci_uart_tty_receive() already calls h4_recv() on HCI_UART_PROTO_INIT or HCI_UART_PROTO_READY. Remove the check for HCI_UART_REGISTERED in h4_recv() to fix the race condition. Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") Signed-off-by: Jonathan Rissanen <jonathan.rissanen@axis.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
12 daysBluetooth: btusb: clamp SCO altsetting table indicesPengpeng Hou1-1/+4
[ Upstream commit 129fa608b6ad08b8ab7178eeb2ec272c993aaccc ] btusb_work() maps the number of active SCO links to USB alternate settings through a three-entry lookup table when CVSD traffic uses transparent voice settings. The lookup currently indexes alts[] with data->sco_num - 1 without first constraining sco_num to the number of available table entries. While the table only defines alternate settings for up to three SCO links, data->sco_num comes from hci_conn_num() and is used directly. Cap the lookup to the last table entry before indexing it so the driver keeps selecting the highest supported alternate setting without reading past alts[]. Fixes: baac6276c0a9 ("Bluetooth: btusb: handle mSBC audio over USB Endpoints") Signed-off-by: Pengpeng Hou <pengpeng@iscas.ac.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
12 daysBluetooth: btintel: serialize btintel_hw_error() with hci_req_sync_lockCen Zhang1-3/+8
[ Upstream commit 94d8e6fe5d0818e9300e514e095a200bd5ff93ae ] btintel_hw_error() issues two __hci_cmd_sync() calls (HCI_OP_RESET and Intel exception-info retrieval) without holding hci_req_sync_lock(). This lets it race against hci_dev_do_close() -> btintel_shutdown_combined(), which also runs __hci_cmd_sync() under the same lock. When both paths manipulate hdev->req_status/req_rsp concurrently, the close path may free the response skb first, and the still-running hw_error path hits a slab-use-after-free in kfree_skb(). Wrap the whole recovery sequence in hci_req_sync_lock/unlock so it is serialized with every other synchronous HCI command issuer. Below is the data race report and the kasan report: BUG: data-race in __hci_cmd_sync_sk / btintel_shutdown_combined read of hdev->req_rsp at net/bluetooth/hci_sync.c:199 by task kworker/u17:1/83: __hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200 __hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223 btintel_hw_error+0x114/0x670 drivers/bluetooth/btintel.c:254 hci_error_reset+0x348/0xa30 net/bluetooth/hci_core.c:1030 write/free by task ioctl/22580: btintel_shutdown_combined+0xd0/0x360 drivers/bluetooth/btintel.c:3648 hci_dev_close_sync+0x9ae/0x2c10 net/bluetooth/hci_sync.c:5246 hci_dev_do_close+0x232/0x460 net/bluetooth/hci_core.c:526 BUG: KASAN: slab-use-after-free in sk_skb_reason_drop+0x43/0x380 net/core/skbuff.c:1202 Read of size 4 at addr ffff888144a738dc by task kworker/u17:1/83: __hci_cmd_sync_sk+0x12f2/0x1c30 net/bluetooth/hci_sync.c:200 __hci_cmd_sync+0x55/0x80 net/bluetooth/hci_sync.c:223 btintel_hw_error+0x186/0x670 drivers/bluetooth/btintel.c:260 Fixes: 973bb97e5aee ("Bluetooth: btintel: Add generic function for handling hardware errors") Signed-off-by: Cen Zhang <zzzccc427@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
12 daysBluetooth: hci_ll: Fix firmware leak on error pathAnas Iqbal1-0/+2
[ Upstream commit 31148a7be723aa9f2e8fbd62424825ab8d577973 ] Smatch reports: drivers/bluetooth/hci_ll.c:587 download_firmware() warn: 'fw' from request_firmware() not released on lines: 544. In download_firmware(), if request_firmware() succeeds but the returned firmware content is invalid (no data or zero size), the function returns without releasing the firmware, resulting in a resource leak. Fix this by calling release_firmware() before returning when request_firmware() succeeded but the firmware content is invalid. Fixes: 371805522f87 ("bluetooth: hci_uart: add LL protocol serdev driver support") Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Anas Iqbal <mohd.abd.6602@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-25Bluetooth: qca: fix ROM version reading on WCN3998 chipsDmitry Baryshkov1-0/+2
[ Upstream commit 99b2c531e0e797119ae1b9195a8764ee98b00e65 ] WCN3998 uses a bit different format for rom version: [ 5.479978] Bluetooth: hci0: setting up wcn399x [ 5.633763] Bluetooth: hci0: QCA Product ID :0x0000000a [ 5.645350] Bluetooth: hci0: QCA SOC Version :0x40010224 [ 5.650906] Bluetooth: hci0: QCA ROM Version :0x00001001 [ 5.665173] Bluetooth: hci0: QCA Patch Version:0x00006699 [ 5.679356] Bluetooth: hci0: QCA controller version 0x02241001 [ 5.691109] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv [ 6.680102] Bluetooth: hci0: QCA Downloading qca/crnv21.bin [ 6.842948] Bluetooth: hci0: QCA setup on UART is completed Fixes: 523760b7ff88 ("Bluetooth: hci_qca: Added support for WCN3998") Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04Bluetooth: hci_qca: Cleanup on all setup failuresJinwang Li1-10/+14
[ Upstream commit 5c4e9a8b18457ad28b57069ef0f14661e3192b2e ] The setup process previously combined error handling and retry gating under one condition. As a result, the final failed attempt exited without performing cleanup. Update the failure path to always perform power and port cleanup on setup failure, and reopen the port only when retrying. Fixes: 9e80587aba4c ("Bluetooth: hci_qca: Enhance retry logic in qca_setup") Signed-off-by: Jinwang Li <jinwang.li@oss.qualcomm.com> Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04Bluetooth: btusb: Add device ID for Realtek RTL8761BUJacopo Scannella1-0/+1
[ Upstream commit cc6383d4f0cf6127c0552f94cae517a06ccc6b17 ] Add USB device ID 0x2c0a:0x8761 to the btusb driver fo the Realtek RTL8761BU Bluetooth adapter. Reference: https://www.startech.com/en-us/networking-io/av53c1-usb-bluetooth Signed-off-by: Jacopo Scannella <code@charlie.cat> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04Bluetooth: btusb: Add new VID/PID for RTL8852CEShell Chen1-0/+2
[ Upstream commit d9f7c39c6b7548bd70519b241b6c2d1bcc658d4b ] Add VID:PID 13d3:3612 to the quirks_table. This ID pair is found in the Realtek RTL8852CE PCIe module in an ASUS TUF A14 2025 (FA401KM) laptop. Tested on aforementioned laptop. The device info from /sys/kernel/debug/usb/devices is listed as below. T: Bus=03 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3612 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Shell Chen <w27@sorz.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04Bluetooth: btusb: Add USB ID 0489:e112 for Realtek 8851BETechie Ernie1-0/+2
[ Upstream commit e07094a51ad8faf98ea64320799ce550828e97cd ] Add USB ID 0489:e112 for the Realtek 8851BE Bluetooth adapter. Without this entry, the device is not handled correctly by btusb and Bluetooth fails to initialise. Adding the ID enables proper Realtek initialization for Bluetooth to work on various motherboards using this Bluetooth adapter. The device identifies as: Bus 001 Device XXX: ID 0489:e112 Foxconn / Hon Hai Bluetooth Radio Tested on Realtek 8851BE. Bluetooth works after this change is made. Signed-off-by: Techie Ernie <techieernie@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04Bluetooth: hci_qca: Fix SSR (SubSystem Restart) fail when BT_EN is pulled up ↵Shuai Zhang1-0/+33
by hw [ Upstream commit fce1a9244a0f85683be8530e623bc729f24c5067 ] On QCS9075 and QCA8275 platforms, the BT_EN pin is always pulled up by hw and cannot be controlled by the host. As a result, in case of a firmware crash, the host cannot trigger a cold reset. Instead, the BT controller performs a warm restart on its own, without reloading the firmware. This leads to the controller remaining in IBS_WAKE state, while the host expects it to be in sleep mode. The mismatch causes HCI reset commands to time out. Additionally, the driver does not clear internal flags QCA_SSR_TRIGGERED and QCA_IBS_DISABLED, which blocks the reset sequence. If the SSR duration exceeds 2 seconds, the host may enter TX sleep mode due to tx_idle_timeout, further preventing recovery. Also, memcoredump_flag is not cleared, so only the first SSR generates a coredump. Tell the driver that the BT controller has undergone a proper restart sequence: - Clear QCA_SSR_TRIGGERED and QCA_IBS_DISABLED flags after SSR. - Add a 50ms delay to allow the controller to complete its warm reset. - Reset tx_idle_timer to prevent the host from entering TX sleep mode. - Clear memcoredump_flag to allow multiple coredump captures. Apply these steps only when HCI_QUIRK_NON_PERSISTENT_SETUP is not set, which indicates that BT_EN is defined in DTS and cannot be toggled. Refer to the comment in include/net/bluetooth/hci.h for details on HCI_QUIRK_NON_PERSISTENT_SETUP. Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-03-04Bluetooth: btusb: Add support for MediaTek7920 0489:e158Bluecross1-0/+2
[ Upstream commit 2630bcc8343a9d2a38dc1793068e6754b3156811 ] Add support for MediaTek7920 0489:e158 /sys/kernel/debug/usb/devices reports for that device: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=03 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e158 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Andrew Elatsev <elantsew.andrew@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-27Bluetooth: btintel_pcie: Use IRQF_ONESHOT and default primary handlerSebastian Andrzej Siewior1-7/+2
[ Upstream commit 28abed6569c87eab9071ab56c64433c2f0d9ce51 ] There is no added value in btintel_pcie_msix_isr() compared to irq_default_primary_handler(). Using a threaded interrupt without a dedicated primary handler mandates the IRQF_ONESHOT flag to mask the interrupt source while the threaded handler is active. Otherwise the interrupt can fire again before the threaded handler had a chance to run. Use the default primary interrupt handler by specifying NULL and set IRQF_ONESHOT so the interrupt source is masked until the secondary handler is done. Fixes: c2b636b3f788d ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@kernel.org> Link: https://patch.msgid.link/20260128095540.863589-7-bigeasy@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
2026-02-16Bluetooth: btusb: Add USB ID 7392:e611 for Edimax EW-7611UXBZenm Chen1-0/+2
commit 6c0568b7741a346088fd6dfced2d871f7d481d06 upstream. Add USB ID 7392:e611 for Edimax EW-7611UXB which is RTL8851BU-based Wi-Fi + Bluetooth adapter. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below: T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=7392 ProdID=e611 Rev= 0.00 S: Manufacturer=Realtek S: Product=802.11ax WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu_git E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable@vger.kernel.org # 6.6.x Signed-off-by: Zenm Chen <zenmchen@gmail.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2026-01-22Bluetooth: hci_uart: fix null-ptr-deref in hci_uart_write_workJia-Hong Su1-2/+2
hci_uart_set_proto() sets HCI_UART_PROTO_INIT before calling hci_uart_register_dev(), which calls proto->open() to initialize hu->priv. However, if a TTY write wakeup occurs during this window, hci_uart_tx_wakeup() may schedule write_work before hu->priv is initialized, leading to a NULL pointer dereference in hci_uart_write_work() when proto->dequeue() accesses hu->priv. The race condition is: CPU0 CPU1 ---- ---- hci_uart_set_proto() set_bit(HCI_UART_PROTO_INIT) hci_uart_register_dev() tty write wakeup hci_uart_tty_wakeup() hci_uart_tx_wakeup() schedule_work(&hu->write_work) proto->open(hu) // initializes hu->priv hci_uart_write_work() hci_uart_dequeue() proto->dequeue(hu) // accesses hu->priv (NULL!) Fix this by moving set_bit(HCI_UART_PROTO_INIT) after proto->open() succeeds, ensuring hu->priv is initialized before any work can be scheduled. Fixes: 5df5dafc171b ("Bluetooth: hci_uart: Fix another race during initialization") Link: https://lore.kernel.org/linux-bluetooth/6969764f.170a0220.2b9fc4.35a7@mx.google.com/ Signed-off-by: Jia-Hong Su <s11242586@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-20Bluetooth: btusb: revert use of devm_kzalloc in btusbRaphael Pinsonneault-Thibeault1-3/+9
This reverts commit 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file"). In btusb_probe(), we use devm_kzalloc() to allocate the btusb data. This ties the lifetime of all the btusb data to the binding of a driver to one interface, INTF. In a driver that binds to other interfaces, ISOC and DIAG, this is an accident waiting to happen. The issue is revealed in btusb_disconnect(), where calling usb_driver_release_interface(&btusb_driver, data->intf) will have devm free the data that is also being used by the other interfaces of the driver that may not be released yet. To fix this, revert the use of devm and go back to freeing memory explicitly. Fixes: 98921dbd00c4e ("Bluetooth: Use devm_kzalloc in btusb.c file") Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: Add new VID/PID 13d3/3533 for RTL8821CEGongwei Li1-0/+2
Add VID 13d3 & PID 3533 for Realtek RTL8821CE USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3533 Rev= 1.10 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Gongwei Li <ligongwei@kylinos.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02drivers/bluetooth: btbcm: Use kmalloc_array() to prevent overflowAyaan Mirza Baig1-1/+3
Replace the open-coded multiplication in kmalloc() with a call to kmalloc_array() to prevent potential integer overflows. This is a mechanical change, replacing BCM_FW_NAME_LEN with the type-safe sizeof(*fw_name) as the element size Signed-off-by: Ayaan Mirza Baig <ayaanmirzabaig85@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btintel_pcie: Introduce HCI Driver protocolChethan T N1-0/+59
This patch adds the infrastructure that allow the user space program to talk to intel pcie driver directly for fetching basic driver details. The changes introduced are referred form commit 04425292a62c15 ("Bluetooth: Introduce HCI Driver protocol") Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: add new custom firmwaresShuai Zhang1-0/+1
The new platform uses the QCA2066 chip along with a new board ID, which requires a dedicated firmware file to ensure proper initialization. Without this entry, the driver cannot locate and load the correct firmware, resulting in Bluetooth bring-up failure. This patch adds a new entry to the firmware table for QCA2066 so that the driver can correctly identify the board ID and load the appropriate firmware from 'qca/QCA2066/' in the linux-firmware repository. Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com> Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: Add new VID/PID 0x13d3/0x3619 for RTL8852BE-VTMax Chou1-0/+2
Add the support ID(0x13d3, 0x3619) to usb_device_id table for Realtek RTL8852BE-VT. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3619 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: Add new VID/PID 0x13d3/0x3618 for RTL8852BE-VTMax Chou1-0/+2
Add the support ID(0x13d3, 0x3618) to usb_device_id table for Realtek RTL8852BE-VT. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3618 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: Add new VID/PID 0x0489/0xE12F for RTL8852BE-VTMax Chou1-0/+2
Add the support ID(0x0489, 0xE12F) to usb_device_id table for Realtek RTL8852BE-VT. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=04 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 86 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e12f Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btrtl: Add the support for RTL8761CUVMax Chou1-1/+15
Add support for RTL8761CUV BT controller on the USB interface. Do not apply IC_MATCH_FL_HCIVER when hci_ver is 0 in the ic_id_table. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 13 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0bda ProdID=c761 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Controller S: SerialNumber=10000 C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: Remove redundant pm_runtime_mark_last_busy() callsSakari Ailus4-11/+1
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(), pm_runtime_autosuspend() and pm_request_autosuspend() now include a call to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to pm_runtime_mark_last_busy(). Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: Reclassify Qualcomm WCN6855 debug packetsPascal Giard1-0/+19
Some Qualcomm Bluetooth controllers, e.g., QCNFA765 with WCN6855 chip, send debug packets as ACL frames with header 0x2EDC. The kernel misinterprets these as malformed ACL packets, causing repeated errors: Bluetooth: hci0: ACL packet for unknown connection handle 3804 This can occur hundreds of times per minute, greatly cluttering logs. On my computer, I am observing approximately 7 messages per second when streaming audio to a speaker. For Qualcomm controllers exchanging over UART, hci_qca.c already filters out these debug packets. This patch is for controllers not going through UART, but USB. This patch uses the classify_pkt_type callback to reclassify the packets with handle 0x2EDC as HCI_DIAG_PKT before they reach the HCI layer. This change is only applied to Qualcomm devices marked as BTUSB_QCA_WCN6855. Tested on: Thinkpad T14 gen2 (AMD) with QCNFA765 (0489:E0D0) Signed-off-by: Pascal Giard <pascal.giard@etsmtl.ca> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: Add new VID/PID 2b89/6275 for RTL8761BUVChingbin Li1-0/+2
Add VID 2b89 & PID 6275 for Realtek RTL8761BUV USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 6 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2b89 ProdID=6275 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Chingbin Li <liqb365@163.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btintel_pcie: Suspend/Resume: Controller doorbell interrupt handlingRavindra2-42/+73
Due to a hardware bug during suspend/resume, the controller may miss a doorbell interrupt. To address this, a retry mechanism has been added to inform the controller before reporting a failure. Test case: - run suspend and resume cycles. Signed-off-by: Ravindra <ravindra@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btintel_pcie: Support for S4 (Hibernate)Ravindra2-0/+43
During S4 (hibernate), the Bluetooth device loses power. Upon resume, the driver performs the following actions: 1. Unregisters hdev 2. Calls function level reset 3. Registers hdev Test case: - run command sudo rtcwake -m disk -s 60 Signed-off-by: Ravindra <ravindra@intel.com> Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: MT7922: Add VID/PID 0489/e170Chris Lu1-0/+2
Add VID 0489 & PID e170 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e170 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-02Bluetooth: btusb: MT7920: Add VID/PID 0489/e135Chris Lu1-0/+2
Add VID 0489 & PID e135 for MediaTek MT7920 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e135 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: hci_h5: implement CRC data integrityJavier Nieto2-4/+39
The UART-based H5 protocol supports CRC data integrity checks for reliable packets. The host sets bit 5 in the configuration field of the CONFIG link control message to indicate that CRC is supported. The controller sets the same bit in the CONFIG RESPONSE message to indicate that CRC may be used from then on. Tested on a MangoPi MQ-Pro with a Realtek RTL8723DS Bluetooth controller using the tip of the bluetooth-next tree. Signed-off-by: Javier Nieto <jgnieto@cs.stanford.edu> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: hci_h5: avoid sending two SYNC messagesJavier Nieto1-4/+5
Previously, h5_open() called h5_link_control() to send a SYNC message. But h5_link_control() only enqueues the packet and requires the caller to call hci_uart_tx_wakeup(). Thus, after H5_SYNC_TIMEOUT ran out (100ms), h5_timed_event() would be called and, realizing that the state was still H5_UNINITIALIZED, it would re-enqueue the SYNC and call hci_uart_tx_wakeup(). Consequently, two SYNC packets would be sent and initialization would unnecessarily wait for 100ms. The naive solution of calling hci_uart_tx_wakeup() in h5_open() does not work because it will only schedule tx work if the HCI_PROTO_READY bit is set and hci_serdev only sets it after h5_open() returns. This patch removes the extraneous SYNC being enqueued and makes h5_timed_event() wake up on the next jiffy. Signed-off-by: Javier Nieto <jgnieto@cs.stanford.edu> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-12-01Bluetooth: mediatek: add gpio pin to reset btZhangchao Zhang1-0/+13
Support the platform Bluetooth to be reset by hardware pin, when a Bluetooth exception occurs, attempt to reset the Bluetooth module using the hardware reset pin, as this method is generally more stable and reliable than a software reset. If the hardware reset pin is not specified in the device tree, fall back to the existing software reset mechanism to ensure backward compatibility. Co-developed: Sean Wang <Sean.Wang@mediatek.com> Co-developed: Hao Qin <hao.qin@mediatek.com> Co-developed: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Zhangchao Zhang <ot_zhangchao.zhang@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-11-21Bluetooth: btusb: mediatek: Avoid btusb_mtk_claim_iso_intf() NULL derefDouglas Anderson1-0/+5
In btusb_mtk_setup(), we set `btmtk_data->isopkt_intf` to: usb_ifnum_to_if(data->udev, MTK_ISO_IFNUM) That function can return NULL in some cases. Even when it returns NULL, though, we still go on to call btusb_mtk_claim_iso_intf(). As of commit e9087e828827 ("Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()"), calling btusb_mtk_claim_iso_intf() when `btmtk_data->isopkt_intf` is NULL will cause a crash because we'll end up passing a bad pointer to device_lock(). Prior to that commit we'd pass the NULL pointer directly to usb_driver_claim_interface() which would detect it and return an error, which was handled. Resolve the crash in btusb_mtk_claim_iso_intf() by adding a NULL check at the start of the function. This makes the code handle a NULL `btmtk_data->isopkt_intf` the same way it did before the problematic commit (just with a slight change to the error message printed). Reported-by: IncogCyberpunk <incogcyberpunk@proton.me> Closes: http://lore.kernel.org/r/a380d061-479e-4713-bddd-1d6571ca7e86@leemhuis.info Fixes: e9087e828827 ("Bluetooth: btusb: mediatek: Add locks for usb_driver_claim_interface()") Cc: stable@vger.kernel.org Tested-by: IncogCyberpunk <incogcyberpunk@proton.me> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-11-21Bluetooth: btusb: mediatek: Fix kernel crash when releasing mtk iso interfaceChris Lu1-7/+27
When performing reset tests and encountering abnormal card drop issues that lead to a kernel crash, it is necessary to perform a null check before releasing resources to avoid attempting to release a null pointer. <4>[ 29.158070] Hardware name: Google Quigon sku196612/196613 board (DT) <4>[ 29.158076] Workqueue: hci0 hci_cmd_sync_work [bluetooth] <4>[ 29.158154] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) <4>[ 29.158162] pc : klist_remove+0x90/0x158 <4>[ 29.158174] lr : klist_remove+0x88/0x158 <4>[ 29.158180] sp : ffffffc0846b3c00 <4>[ 29.158185] pmr_save: 000000e0 <4>[ 29.158188] x29: ffffffc0846b3c30 x28: ffffff80cd31f880 x27: ffffff80c1bdc058 <4>[ 29.158199] x26: dead000000000100 x25: ffffffdbdc624ea3 x24: ffffff80c1bdc4c0 <4>[ 29.158209] x23: ffffffdbdc62a3e6 x22: ffffff80c6c07000 x21: ffffffdbdc829290 <4>[ 29.158219] x20: 0000000000000000 x19: ffffff80cd3e0648 x18: 000000031ec97781 <4>[ 29.158229] x17: ffffff80c1bdc4a8 x16: ffffffdc10576548 x15: ffffff80c1180428 <4>[ 29.158238] x14: 0000000000000000 x13: 000000000000e380 x12: 0000000000000018 <4>[ 29.158248] x11: ffffff80c2a7fd10 x10: 0000000000000000 x9 : 0000000100000000 <4>[ 29.158257] x8 : 0000000000000000 x7 : 7f7f7f7f7f7f7f7f x6 : 2d7223ff6364626d <4>[ 29.158266] x5 : 0000008000000000 x4 : 0000000000000020 x3 : 2e7325006465636e <4>[ 29.158275] x2 : ffffffdc11afeff8 x1 : 0000000000000000 x0 : ffffffdc11be4d0c <4>[ 29.158285] Call trace: <4>[ 29.158290] klist_remove+0x90/0x158 <4>[ 29.158298] device_release_driver_internal+0x20c/0x268 <4>[ 29.158308] device_release_driver+0x1c/0x30 <4>[ 29.158316] usb_driver_release_interface+0x70/0x88 <4>[ 29.158325] btusb_mtk_release_iso_intf+0x68/0xd8 [btusb (HASH:e8b6 5)] <4>[ 29.158347] btusb_mtk_reset+0x5c/0x480 [btusb (HASH:e8b6 5)] <4>[ 29.158361] hci_cmd_sync_work+0x10c/0x188 [bluetooth (HASH:a4fa 6)] <4>[ 29.158430] process_scheduled_works+0x258/0x4e8 <4>[ 29.158441] worker_thread+0x300/0x428 <4>[ 29.158448] kthread+0x108/0x1d0 <4>[ 29.158455] ret_from_fork+0x10/0x20 <0>[ 29.158467] Code: 91343000 940139d1 f9400268 927ff914 (f9401297) <4>[ 29.158474] ---[ end trace 0000000000000000 ]--- <0>[ 29.167129] Kernel panic - not syncing: Oops: Fatal exception <2>[ 29.167144] SMP: stopping secondary CPUs <4>[ 29.167158] ------------[ cut here ]------------ Fixes: ceac1cb0259d ("Bluetooth: btusb: mediatek: add ISO data transmission functions") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-11-11Bluetooth: btrtl: Avoid loading the config file on security chipsMax Chou1-11/+13
For chips with security enabled, it's only possible to load firmware with a valid signature pattern. If key_id is not zero, it indicates a security chip, and the driver will not load the config file. - Example log for a security chip. Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a lmp_ver=0c lmp_subver=8922 Bluetooth: hci0: RTL: rom_version status=0 version=1 Bluetooth: hci0: RTL: btrtl_initialize: key id 1 Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin Bluetooth: hci0: RTL: cfg_sz 0, total sz 71301 Bluetooth: hci0: RTL: fw version 0x41c0c905 - Example log for a normal chip. Bluetooth: hci0: RTL: examining hci_ver=0c hci_rev=000a lmp_ver=0c lmp_subver=8922 Bluetooth: hci0: RTL: rom_version status=0 version=1 Bluetooth: hci0: RTL: btrtl_initialize: key id 0 Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_fw.bin Bluetooth: hci0: RTL: loading rtl_bt/rtl8922au_config.bin Bluetooth: hci0: RTL: cfg_sz 6, total sz 71307 Bluetooth: hci0: RTL: fw version 0x41c0c905 Tested-by: Hilda Wu <hildawu@realtek.com> Signed-off-by: Nial Ni <niall_ni@realsil.com.cn> Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-11-11Bluetooth: btusb: reorder cleanup in btusb_disconnect to avoid UAFRaphael Pinsonneault-Thibeault1-7/+6
There is a KASAN: slab-use-after-free read in btusb_disconnect(). Calling "usb_driver_release_interface(&btusb_driver, data->intf)" will free the btusb data associated with the interface. The same data is then used later in the function, hence the UAF. Fix by moving the accesses to btusb data to before the data is free'd. Reported-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=2fc81b50a4f8263a159b Tested-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com Fixes: fd913ef7ce619 ("Bluetooth: btusb: Add out-of-band wakeup support") Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-10-31Bluetooth: btrtl: Fix memory leak in rtlbt_parse_firmware_v2()Abdun Nihaal1-1/+3
The memory allocated for ptr using kvmalloc() is not freed on the last error path. Fix that by freeing it on that error path. Fixes: 9a24ce5e29b1 ("Bluetooth: btrtl: Firmware format v2 support") Signed-off-by: Abdun Nihaal <nihaal@cse.iitm.ac.in> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-10-24Bluetooth: fix corruption in h4_recv_buf() after cleanupCalvin Owens14-19/+25
A different structure is stored in drvdata for the drivers which used that duplicate function, but h4_recv_buf() assumes drvdata is always an hci_uart structure. Consequently, alignment and padding are now randomly corrupted for btmtkuart, btnxpuart, and bpa10x in h4_recv_buf(), causing erratic breakage. Fix this by making the hci_uart structure the explicit argument to h4_recv_buf(). Every caller already has a reference to hci_uart, and already obtains the hci_hdev reference through it, so this actually eliminates a redundant pointer indirection for all existing callers. Fixes: 93f06f8f0daf ("Bluetooth: remove duplicate h4_recv_buf() in header") Reported-by: Francesco Valla <francesco@valla.it> Closes: https://lore.kernel.org/lkml/6837167.ZASKD2KPVS@fedora.fritz.box/ Signed-off-by: Calvin Owens <calvin@wbinvd.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-10-24Bluetooth: btintel_pcie: Fix event packet loss issueKiran K1-5/+6
In the current btintel_pcie driver implementation, when an interrupt is received, the driver checks for the alive cause before the TX/RX cause. Handling the alive cause involves resetting the TX/RX queue indices. This flow works correctly when the causes are mutually exclusive. However, if both cause bits are set simultaneously, the alive cause resets the queue indices, resulting in an event packet drop and a command timeout. To fix this issue, the driver is modified to handle all other causes before checking for the alive cause. Test case: Issue is seen with stress reboot scenario - 50x run [20.337589] Bluetooth: hci0: Device revision is 0 [20.346750] Bluetooth: hci0: Secure boot is enabled [20.346752] Bluetooth: hci0: OTP lock is disabled [20.346752] Bluetooth: hci0: API lock is enabled [20.346752] Bluetooth: hci0: Debug lock is disabled [20.346753] Bluetooth: hci0: Minimum firmware build 1 week 10 2014 [20.346754] Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631 [20.359070] Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi [20.371499] Bluetooth: hci0: Boot Address: 0xb02ff800 [20.385769] Bluetooth: hci0: Firmware Version: 166-34.25 [20.538257] Bluetooth: hci0: Waiting for firmware download to complete [20.554424] Bluetooth: hci0: Firmware loaded in 178651 usecs [21.081588] Bluetooth: hci0: Timeout (500 ms) on tx completion [21.096541] Bluetooth: hci0: Failed to send frame (-62) [21.110240] Bluetooth: hci0: sending frame failed (-62) [21.138551] Bluetooth: hci0: Failed to send Intel Reset command [21.170153] Bluetooth: hci0: Intel Soft Reset failed (-62) Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Fixes: c2b636b3f788 ("Bluetooth: btintel_pcie: Add support for PCIe transport") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-10-24Bluetooth: btmtksdio: Add pmctrl handling for BT closed state during resetChris Lu1-0/+12
This patch adds logic to handle power management control when the Bluetooth function is closed during the SDIO reset sequence. Specifically, if BT is closed before reset, the driver enables the SDIO function and sets driver pmctrl. After reset, if BT remains closed, the driver sets firmware pmctrl and disables the SDIO function. These changes ensure proper power management and device state consistency across the reset flow. Fixes: 8fafe702253d ("Bluetooth: mt7921s: support bluetooth reset mechanism") Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: bcsp: receive data only if registeredIvan Pravdin1-0/+3
Currently, bcsp_recv() can be called even when the BCSP protocol has not been registered. This leads to a NULL pointer dereference, as shown in the following stack trace: KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f] RIP: 0010:bcsp_recv+0x13d/0x1740 drivers/bluetooth/hci_bcsp.c:590 Call Trace: <TASK> hci_uart_tty_receive+0x194/0x220 drivers/bluetooth/hci_ldisc.c:627 tiocsti+0x23c/0x2c0 drivers/tty/tty_io.c:2290 tty_ioctl+0x626/0xde0 drivers/tty/tty_io.c:2706 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:907 [inline] __se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893 do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline] do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94 entry_SYSCALL_64_after_hwframe+0x77/0x7f To prevent this, ensure that the HCI_UART_REGISTERED flag is set before processing received data. If the protocol is not registered, return -EUNATCH. Reported-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=4ed6852d4da4606c93da Tested-by: syzbot+4ed6852d4da4606c93da@syzkaller.appspotmail.com Signed-off-by: Ivan Pravdin <ipravdin.official@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btusb: Add new VID/PID 13d3/3633 for MT7922Chris Lu1-0/+2
Add VID 13d3 & PID 3633 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3633 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btusb: Add new VID/PID 13d3/3627 for MT7925Chris Lu1-0/+2
Add VID 13d3 & PID 3627 for MediaTek MT7922 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3627 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Chris Lu <chris.lu@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: remove duplicate h4_recv_buf() in headerCalvin Owens5-157/+4
The "h4_recv.h" header contains a duplicate h4_recv_buf() that is nearly but not quite identical to the h4_recv_buf() in hci_h4.c. This duplicated header was added in commit 07eb96a5a7b0 ("Bluetooth: bpa10x: Use separate h4_recv_buf helper"). I wasn't able to find any explanation for duplicating the code in the discussion: https://lore.kernel.org/all/20180320181855.37297-1-marcel@holtmann.org/ https://lore.kernel.org/all/20180324091954.73229-2-marcel@holtmann.org/ Unfortunately, in the years since, several other drivers have come to also rely on this duplicated function, probably by accident. This is, at the very least, *extremely* confusing. It's also caused real issues when it's become out-of-sync, see the following: ef564119ba83 ("Bluetooth: hci_h4: Add support for ISO packets") 61b27cdf025b ("Bluetooth: hci_h4: Add support for ISO packets in h4_recv.h") This is the full diff between the two implementations today: --- orig.c +++ copy.c @@ -1,117 +1,100 @@ { - struct hci_uart *hu = hci_get_drvdata(hdev); - u8 alignment = hu->alignment ? hu->alignment : 1; - /* Check for error from previous call */ if (IS_ERR(skb)) skb = NULL; while (count) { int i, len; - /* remove padding bytes from buffer */ - for (; hu->padding && count > 0; hu->padding--) { - count--; - buffer++; - } - if (!count) - break; - if (!skb) { for (i = 0; i < pkts_count; i++) { if (buffer[0] != (&pkts[i])->type) continue; skb = bt_skb_alloc((&pkts[i])->maxlen, GFP_ATOMIC); if (!skb) return ERR_PTR(-ENOMEM); hci_skb_pkt_type(skb) = (&pkts[i])->type; hci_skb_expect(skb) = (&pkts[i])->hlen; break; } /* Check for invalid packet type */ if (!skb) return ERR_PTR(-EILSEQ); count -= 1; buffer += 1; } len = min_t(uint, hci_skb_expect(skb) - skb->len, count); skb_put_data(skb, buffer, len); count -= len; buffer += len; /* Check for partial packet */ if (skb->len < hci_skb_expect(skb)) continue; for (i = 0; i < pkts_count; i++) { if (hci_skb_pkt_type(skb) == (&pkts[i])->type) break; } if (i >= pkts_count) { kfree_skb(skb); return ERR_PTR(-EILSEQ); } if (skb->len == (&pkts[i])->hlen) { u16 dlen; switch ((&pkts[i])->lsize) { case 0: /* No variable data length */ dlen = 0; break; case 1: /* Single octet variable length */ dlen = skb->data[(&pkts[i])->loff]; hci_skb_expect(skb) += dlen; if (skb_tailroom(skb) < dlen) { kfree_skb(skb); return ERR_PTR(-EMSGSIZE); } break; case 2: /* Double octet variable length */ dlen = get_unaligned_le16(skb->data + (&pkts[i])->loff); hci_skb_expect(skb) += dlen; if (skb_tailroom(skb) < dlen) { kfree_skb(skb); return ERR_PTR(-EMSGSIZE); } break; default: /* Unsupported variable length */ kfree_skb(skb); return ERR_PTR(-EILSEQ); } if (!dlen) { - hu->padding = (skb->len + 1) % alignment; - hu->padding = (alignment - hu->padding) % alignment; - /* No more data, complete frame */ (&pkts[i])->recv(hdev, skb); skb = NULL; } } else { - hu->padding = (skb->len + 1) % alignment; - hu->padding = (alignment - hu->padding) % alignment; - /* Complete frame */ (&pkts[i])->recv(hdev, skb); skb = NULL; } } return skb; } -EXPORT_SYMBOL_GPL(h4_recv_buf) As I read this: If alignment is one, and padding is zero, padding remains zero throughout the loop. So it seems to me that the two functions behave strictly identically in that case. All the duplicated defines are also identical, as is the duplicated h4_recv_pkt structure declaration. All four drivers which use the duplicated function use the default alignment of one, and the default padding of zero. I therefore conclude the duplicate function may be safely replaced with the core one. I raised this in an RFC a few months ago, and didn't get much interest: https://lore.kernel.org/all/CABBYNZ+ONkYtq2fR-8PtL3X-vetvJ0BdP4MTw9cNpjLDzG3HUQ@mail.gmail.com/ ...but I'm still wary I've missed something, and I'd really appreciate more eyeballs on it. I tested this successfully on btnxpuart a few months ago, but unfortunately I no longer have access to that hardware. Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Calvin Owens <calvin@wbinvd.org> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btusb: Check for unexpected bytes when defragmenting HCI framesArkadiusz Bokowy1-0/+17
Some Barrot based USB Bluetooth dongles erroneously send one extra random byte for the HCI_OP_READ_LOCAL_EXT_FEATURES command. The consequence of that is that the next HCI transfer is misaligned by one byte causing undefined behavior. In most cases the response event for the next command fails with random error code. Since the HCI_OP_READ_LOCAL_EXT_FEATURES command is used during HCI controller initialization, the initialization fails rendering the USB dongle not usable. > [59.464099] usb 1-1.3: new full-speed USB device number 11 using xhci_hcd > [59.561617] usb 1-1.3: New USB device found, idVendor=33fa, idProduct=0012, bcdDevice=88.91 > [59.561642] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0 > [59.561656] usb 1-1.3: Product: UGREEN BT6.0 Adapter > [61.720116] Bluetooth: hci1: command 0x1005 tx timeout > [61.720167] Bluetooth: hci1: Opcode 0x1005 failed: -110 This patch was tested with the 33fa:0012 device. The info from the /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 12 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=33fa ProdID=0012 Rev=88.91 S: Product=UGREEN BT6.0 Adapter C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Now the device is initialized properly: > [43.329852] usb 1-1.4: new full-speed USB device number 4 using dwc_otg > [43.446790] usb 1-1.4: New USB device found, idVendor=33fa, idProduct=0012, bcdDevice=88.91 > [43.446813] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0 > [43.446821] usb 1-1.4: Product: UGREEN BT6.0 Adapter > [43.582024] Bluetooth: hci1: Unexpected continuation: 1 bytes > [43.703025] Bluetooth: hci1: Unexpected continuation: 1 bytes > [43.750141] Bluetooth: MGMT ver 1.23 Link: https://github.com/bluez/bluez/issues/1326 Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com> Tested-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btintel_pcie: Refactor Device CoredumpKiran K2-145/+77
As device coredumps are not HCI traces, maintain the device coredump at the driver level and eliminate the dependency on hdev_devcd*() Signed-off-by: Kiran K <kiran.k@intel.com> Fixes: 07e6bddb54b4 ("Bluetooth: btintel_pcie: Add support for device coredump") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btintel_pcie: Use strscpy() instead of strscpy_pad()Thorsten Blum1-2/+3
kzalloc() already zero-initializes the destination buffer 'data', making strscpy() sufficient for safely copying 'name'. The additional NUL-padding performed by strscpy_pad() is unnecessary. Add a new local variable to store the length of 'name' and reuse it instead of recalculating the same length. Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btintel_pcie: Define hdev->wakeup() callbackChandrashekar Devegowda1-0/+8
Implement hdev->wakeup() callback to support Wake On BT feature. Test steps: 1. echo enabled > /sys/bus/pci/devices/0000:00:14.7/power/wakeup 2. connect bluetooth hid device 3. put the system to suspend - rtcwake -m mem -s 300 4. press any key on hid to wake up the system Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2025-09-27Bluetooth: btusb: Add USB ID 2001:332a for D-Link AX9U rev. A1Zenm Chen1-0/+2
Add USB ID 2001:332a for D-Link AX9U rev. A1 which is based on a Realtek RTL8851BU chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below: T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2001 ProdID=332a Rev= 0.00 S: Manufacturer=Realtek S: Product=802.11ax WLAN Adapter S: SerialNumber=00e04c000001 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtw89_8851bu_git E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Cc: stable@vger.kernel.org # 6.12.x Signed-off-by: Zenm Chen <zenmchen@gmail.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2026-04-14 12:29:24 +0300