| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
This makes CMA memory area size zero for x86 in default configuration
(doesn't change on the other architectures). If default CMA size is
zero, DMA_CMA is disabled. It can be enabled by passing cma= to the
kernel.
This makes less impact on x86. Because there is no mainline driver that
requires it for x86, and Peter Hurley reported the performance
regression, as this is trying to drive _all_ dma mapping allocations
through a _very_ small window.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Chuck Ebbert <cebbert.lkml@gmail.com>
Cc: Jean Delvare <jdelvare@suse.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Don Dutile <ddutile@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* pm-runtime: (25 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
PM / Kconfig: Do not select PM directly from Kconfig files
PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
...
|
|
* pm-domains:
ARM: shmobile: Convert to genpd flags for PM clocks for R-mobile
ARM: shmobile: Convert to genpd flags for PM clocks for r8a7779
PM / Domains: Initial PM clock support for genpd
PM / Domains: Power on the PM domain right after attach completes
PM / Domains: Move struct pm_domain_data to pm_domain.h
PM / Domains: Extract code to power off/on a PM domain
PM / Domains: Make genpd parameter of pm_genpd_present() const
* pm-sleep:
PM / hibernate: Deletion of an unnecessary check before the function call "vfree"
PM / Hibernate: Migrate to ktime_t
* pm-tools:
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
|
|
* powercap:
powercap / RAPL: fix build dependency on iosf_mbi
powercap / RAPL: add new model ids
powercap / RAPL: handle atom and core differences
powercap / RAPL: abstract per cpu type functions
* pm-clk:
PM / clock_ops: make __pm_clk_enable more generic
PM / clock_ops: Add pm_clk_add_clk()
* pm-config:
PM: Kconfig: fix unmet dependency for CPU_PM
* pm-opp:
PM / OPP replace kfree_rcu() with call_srcu() in opp_set_availability()
PM / OPP Introduce APIs to remove OPPs
PM / OPP mark OPPs as 'static' or 'dynamic'
PM / OPP don't match for existing OPPs when list is empty
PM / OPP rename 'head' as 'rcu_head' or 'srcu_head' based on its type
|
|
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM or even may be dropped entirely in some cases.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PM core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It's quite common for PM domains to use PM clocks. Typically from SOC
specific code, the per device PM clock list is created and
pm_clk_suspend|resume() are invoked to handle clock gating/ungating.
A step towards consolidation is to integrate PM clock support into
genpd, which is what this patch does.
In this initial step, the calls to the pm_clk_suspend|resume() are
handled within genpd, but the per device PM clock list still needs to
be created from SOC specific code. It seems reasonable to have gendp to
handle that as well, but that left to future patches to address.
It's not every users of genpd that are keen on using PM clocks, thus we
need to provide this a configuration option for genpd. Therefore let's
add flag field in the genpd struct to keep this information and define
a new GENDP_FLAG_PM_CLK bit for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This existed before we introduced call_srcu() in opp layer to synchronize with
srcu_notifier_call_chain() while removing OPPs. And is a potential bug which
wasn't noticed earlier.
Let fix it as well by using the right API to free OPP.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
OPPs are created statically (from DT) or dynamically. Currently we don't free
OPPs that are created statically, when the module unloads. And so if the module
is inserted back again, we get warning for duplicate OPPs as the same were
already present.
Also, there might be a need to remove dynamic OPPs in future and so API for that
is also added.
This patch adds helper APIs to remove/free existing static and dynamic OPPs.
Because the OPPs are used both under RCU and SRCU, we have to wait for grace
period of both. And so are using kfree_rcu() from within call_srcu().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Static OPPs are the ones created from Device Tree entries and dynamic are the
ones created at runtime by calling dev_pm_opp_add().
There is a need to distinguish them as we need to free static OPPs from cpufreq
drivers when they are removed.
So, add another field 'dynamic' in 'struct dev_pm_opp' to keep this information.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
OPP list is guaranteed to be empty when 'dev_opp' is created. And so we don't
need to run the comparison loop with existing OPPs.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Both 'struct dev_pm_opp' and 'struct device_opp' have member with name 'head'
but with different types. This leads to confusion while reading the code.
Name them 'rcu_head' and 'srcu_head'.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
|
|
'regmap/topic/headers' into regmap-next
|
|
|
|
|
|
Vast amount of platform drivers which enables runtime PM, don't invoke
a pm_runtime_get_sync() while probing their devices.
Instead, once they have turned on their PM resourses during ->probe()
and are ready to handle I/O, these invokes pm_runtime_set_active() to
synchronize its state towards the runtime PM core.
From the runtime PM point of view this behavior is perfectly acceptable,
but we encounter probe failures if their corresponding devices resides
in the generic PM domain. The issues are observed for those devices,
which requires its PM domain to stay powered during ->probe() since
that's not being controlled.
While using the generic OF-based PM domain look-up, a device's PM
domain will be attached during the probe sequence. For this path, let's
fix the probe failures, by simply power on the PM domain right after
when it's been attached to the device.
The generic PM domain stays powered until all of its devices becomes
runtime PM enabled and runtime PM suspended.
The old SOCs which makes use of the generic PM domain but don't use the
generic OF-based PM domain look-up, will not be affected from this
change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the recently added support for bus operations to provide a standard
mapping for AC'97 register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
|
|
* pm-domains:
PM / Domains: Fix initial default state of the need_restore flag
PM / Domains: Change prototype for the attach and detach callbacks
* pm-sleep:
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
* pm-cpufreq:
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
|
|
PM domains are powered on/off from various places. Some callers do
latency measurements, others don't. Consolidate using two helper
functions, which always measure the latencies, and update the stored
latencies when needed.
Other minor changes:
- Use pr_warn() instead of pr_warning(),
- There's no need to check genpd->name, %s handles NULL pointers fine,
- Make the warning format strings identical, to save memory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The PM domain pointed to by the genpd parameter is never modified.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The initial state of the device's need_restore flag should'nt depend on
the current state of the PM domain. For example it should be perfectly
valid to attach an inactive device to a powered PM domain.
The pm_genpd_dev_need_restore() API allow us to update the need_restore
flag to somewhat cope with such scenarios. Typically that should have
been done from drivers/buses ->probe() since it's those that put the
requirements on the value of the need_restore flag.
Until recently, the Exynos SOCs were the only user of the
pm_genpd_dev_need_restore() API, though invoking it from a centralized
location while adding devices to their PM domains.
Due to that Exynos now have swithed to the generic OF-based PM domain
look-up, it's no longer possible to invoke the API from a centralized
location. The reason is because devices are now added to their PM
domains during the probe sequence.
Commit "ARM: exynos: Move to generic PM domain DT bindings"
did the switch for Exynos to the generic OF-based PM domain look-up,
but it also removed the call to pm_genpd_dev_need_restore(). This
caused a regression for some of the Exynos drivers.
To handle things more properly in the generic PM domain, let's change
the default initial value of the need_restore flag to reflect that the
state is unknown. As soon as some of the runtime PM callbacks gets
invoked, update the initial value accordingly.
Moreover, since the generic PM domain is verifying that all devices
are both runtime PM enabled and suspended, using pm_runtime_suspended()
while pm_genpd_poweroff() is invoked from the scheduled work, we can be
sure of that the PM domain won't be powering off while having active
devices.
Do note that, the generic PM domain can still only know about active
devices which has been activated through invoking its runtime PM resume
callback. In other words, buses/drivers using pm_runtime_set_active()
during ->probe() will still suffer from a race condition, potentially
probing a device without having its PM domain being powered. That issue
will have to be solved using a different approach.
This a log from the boot regression for Exynos5, which is being fixed in
this patch.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 308 at ../drivers/clk/clk.c:851 clk_disable+0x24/0x30()
Modules linked in:
CPU: 0 PID: 308 Comm: kworker/0:1 Not tainted 3.18.0-rc3-00569-gbd9449f-dirty #10
Workqueue: pm pm_runtime_work
[<c0013c64>] (unwind_backtrace) from [<c0010dec>] (show_stack+0x10/0x14)
[<c0010dec>] (show_stack) from [<c03ee4cc>] (dump_stack+0x70/0xbc)
[<c03ee4cc>] (dump_stack) from [<c0020d34>] (warn_slowpath_common+0x64/0x88)
[<c0020d34>] (warn_slowpath_common) from [<c0020d74>] (warn_slowpath_null+0x1c/0x24)
[<c0020d74>] (warn_slowpath_null) from [<c03107b0>] (clk_disable+0x24/0x30)
[<c03107b0>] (clk_disable) from [<c02cc834>] (gsc_runtime_suspend+0x128/0x160)
[<c02cc834>] (gsc_runtime_suspend) from [<c0249024>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c0249024>] (pm_generic_runtime_suspend) from [<c024f44c>] (pm_genpd_default_save_state+0x2c/0x8c)
[<c024f44c>] (pm_genpd_default_save_state) from [<c024ff2c>] (pm_genpd_poweroff+0x224/0x3ec)
[<c024ff2c>] (pm_genpd_poweroff) from [<c02501b4>] (pm_genpd_runtime_suspend+0x9c/0xcc)
[<c02501b4>] (pm_genpd_runtime_suspend) from [<c024a4f8>] (__rpm_callback+0x2c/0x60)
[<c024a4f8>] (__rpm_callback) from [<c024a54c>] (rpm_callback+0x20/0x74)
[<c024a54c>] (rpm_callback) from [<c024a930>] (rpm_suspend+0xd4/0x43c)
[<c024a930>] (rpm_suspend) from [<c024bbcc>] (pm_runtime_work+0x80/0x90)
[<c024bbcc>] (pm_runtime_work) from [<c0032a9c>] (process_one_work+0x12c/0x314)
[<c0032a9c>] (process_one_work) from [<c0032cf4>] (worker_thread+0x3c/0x4b0)
[<c0032cf4>] (worker_thread) from [<c003747c>] (kthread+0xcc/0xe8)
[<c003747c>] (kthread) from [<c000e738>] (ret_from_fork+0x14/0x3c)
---[ end trace 40cd58bcd6988f12 ]---
Fixes: a4a8c2c4962bb655 (ARM: exynos: Move to generic PM domain DT bindings)
Reported-and-tested0by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Convert the prototypes to return an int in order to support error
handling in these callbacks.
Also, as suggested by Dmitry Torokhov, pass the domain pointer for use
inside the callbacks, and so that they match the existing
power_on/power_off callbacks which currently take the domain pointer.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ khilman: added domain as parameter to callbacks, as suggested by Dmitry ]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The ENABLE_DEV_COREDUMP option is misleading as it implies that
it gets the framework enabled, this isn't true it just allows it
to get enabled if a driver needs it.
Rename it to ALLOW_DEV_COREDUMP to better capture its semantics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's desirable for allnconfig and tinyconfig targets to result in the
least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to
switch off DEV_COREDUMP regardless if any drivers select
WANT_DEV_COREDUMP.
This patch renames the option to ENABLE_DEV_COREDUMP and setting it to
'n' (as in allnconfig or tinyconfig) will effectively disable device
coredump.
Cc: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
-----------------------------------------------------
<4>[ 3965.441471] WARNING: at ...include/linux/kref.h:41 kobject_get+0x33/0x40()
<4>[ 3965.441474] Hardware name: Romley
<4>[ 3965.441475] Modules linked in: isd_iop(O) isd_xda(O)...
...
<4>[ 3965.441605] Call Trace:
<4>[ 3965.441611] [<ffffffff8103717a>] warn_slowpath_common+0x7a/0xb0
<4>[ 3965.441615] [<ffffffff810371c5>] warn_slowpath_null+0x15/0x20
<4>[ 3965.441618] [<ffffffff81215963>] kobject_get+0x33/0x40
<4>[ 3965.441624] [<ffffffff812d1e45>] get_device_parent.isra.11+0x135/0x1f0
<4>[ 3965.441627] [<ffffffff812d22d4>] device_add+0xd4/0x6d0
<4>[ 3965.441631] [<ffffffff812d0dbc>] ? dev_set_name+0x3c/0x40
....
<2>[ 3965.441912] kernel BUG at ..../fs/sysfs/group.c:65!
<4>[ 3965.441915] invalid opcode: 0000 [#1] SMP
...
<4>[ 3965.686743] [<ffffffff811a677e>] sysfs_create_group+0xe/0x10
<4>[ 3965.686748] [<ffffffff810cfb04>] blk_trace_init_sysfs+0x14/0x20
<4>[ 3965.686753] [<ffffffff811fcabb>] blk_register_queue+0x3b/0x120
<4>[ 3965.686756] [<ffffffff812030bc>] add_disk+0x1cc/0x490
....
-------------------------------------------------------
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Weng Meiling <wengmeiling.weng@huawei.com>
Cc: <stable@vger.kernel.org> #3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now there are two places in code which do the same things,
so allow __pm_clk_enable() to accept pointer on pm_clock_entry
structure as second parameter instead of pointer on clock and
remove duplicated code.
Also, updated function intended to be used by following patch.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The existing pm_clk_add() allows to pass a clock by con_id. However,
when referring to a specific clock from DT, no con_id is available.
Add pm_clk_add_clk(), which allows to specify the struct clk * directly.
The will will increment refcount on clock pointer, so the caller has
to use clk_put() on clock pointer when done.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
PM uses three separate functions to fetch RPM callbacks.
These functions uses quite complicated macro in their body.
The patch replaces these routines with one small macro and
one helper function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add new generic routines are provided for retrieving properties from
device description objects in the platform firmware in case there are
no struct device objects for them (either those objects have not been
created yet or they do not exist at all).
The following functions are provided:
fwnode_property_present()
fwnode_property_read_u8()
fwnode_property_read_u16()
fwnode_property_read_u32()
fwnode_property_read_u64()
fwnode_property_read_string()
fwnode_property_read_u8_array()
fwnode_property_read_u16_array()
fwnode_property_read_u32_array()
fwnode_property_read_u64_array()
fwnode_property_read_string_array()
in analogy with the corresponding functions for struct device added
previously. For all of them, the first argument is a pointer to struct
fwnode_handle (new type) that allows a device description object
(depending on what platform firmware interface is in use) to be
obtained.
Add a new macro device_for_each_child_node() for iterating over the
children of the device description object associated with a given
device and a new function device_get_child_node_count() returning the
number of a given device's child nodes.
The interface covers both ACPI and Device Trees.
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a uniform interface by which device drivers can request device
properties from the platform firmware by providing a property name
and the corresponding data type. The purpose of it is to help to
write portable code that won't depend on any particular platform
firmware interface.
The following general helper functions are added:
device_property_present()
device_property_read_u8()
device_property_read_u16()
device_property_read_u32()
device_property_read_u64()
device_property_read_string()
device_property_read_u8_array()
device_property_read_u16_array()
device_property_read_u32_array()
device_property_read_u64_array()
device_property_read_string_array()
The first one allows the caller to check if the given property is
present. The next 5 of them allow single-valued properties of
various types to be retrieved in a uniform way. The remaining 5 are
for reading properties with multiple values (arrays of either numbers
or strings).
The interface covers both ACPI and Device Trees.
This change set includes material from Mika Westerberg and Aaron Lu.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes received after my previous pull request plus one that
has been in the works for quite a while, but its previous version
caused problems to happen, so it's been deferred till now.
Fixed are two recent regressions (MFD enumeration and cpufreq-dt),
ACPI EC regression introduced in 3.17, system suspend error code path
regression introduced in 3.15, an older bug related to recovery from
failing resume from hibernation and a cpufreq-dt driver issue related
to operation performance points.
Specifics:
- Fix a crash on r8a7791/koelsch during resume from system suspend
caused by a recent cpufreq-dt commit (Geert Uytterhoeven).
- Fix an MFD enumeration problem introduced by a recent commit adding
ACPI support to the MFD subsystem that exposed a weakness in the
ACPI core causing ACPI enumeration to be applied to all devices
associated with one ACPI companion object, although it should be
used for one of them only (Mika Westerberg).
- Fix an ACPI EC regression introduced during the 3.17 cycle causing
some Samsung laptops to misbehave as a result of a workaround
targeted at some Acer machines. That includes a revert of a commit
that went too far and a quirk for the Acer machines in question.
From Lv Zheng.
- Fix a regression in the system suspend error code path introduced
during the 3.15 cycle that causes it to fail to take errors from
asychronous execution of "late" suspend callbacks into account
(Imre Deak).
- Fix a long-standing bug in the hibernation resume error code path
that fails to roll back everything correcty on "freeze" callback
errors and leaves some devices in a "suspended" state causing more
breakage to happen subsequently (Imre Deak).
- Make the cpufreq-dt driver disable operation performance points
that are not supported by the VR connected to the CPU voltage plane
with acceptable tolerance instead of constantly failing voltage
scaling later on (Lucas Stach)"
* tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer.
Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus)
PM / Sleep: fix recovery during resuming from hibernation
PM / Sleep: fix async suspend_late/freeze_late error handling
ACPI: Use ACPI companion to match only the first physical device
cpufreq: cpufreq-dt: disable unsupported OPPs
|
|
Driver calling of_reserved_mem_device_init() might be interested if the
initialization has been successful or not, so add support for returning
error code.
This fixes a build warining caused by commit 7bfa5ab6fa1b ("drivers:
dma-coherent: add initialization from device tree"), which has been
merged without this change and without fixing function return value.
Fixes: 7bfa5ab6fa1b1 ("drivers: dma-coherent: add initialization from device tree")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If an asynchronous suspend_late or freeze_late callback fails
during the SUSPEND, FREEZE or QUIESCE phases, we don't propagate the
corresponding error correctly, in effect ignoring the error and
continuing the suspend-to-ram/hibernation. During suspend-to-ram this
could leave some devices without a valid saved context, leading to a
failure to reinitialize them during resume. During hibernation this
could leave some devices active interfeering with the creation /
restoration of the hibernation image. Also this could leave the
corresponding devices without a valid saved context and failure to
reinitialize them during resume.
Fixes: de377b397272 (PM / sleep: Asynchronous threads for suspend_late)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When all the registers are volatile(unlikely, but logically and mostly
will happen for some 'device' who has very few registers), then the
count will be euqal to 0, then kmalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmalloc(). If the count == 0, so we can make sure that all the registers
are volatile, so no cache is need.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch fixes checkpatch.pl warning for regmap cache.
WARNING : prefer kmalloc_array over kmalloc with multiply
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This may speed regcache_hw_init() up for some cases that there
has volatile registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When kmalloc() fails, we should return -ENOMEM.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the redundant code for regmap cache.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This pull-request includes:
- change in the IOMMU-API to convert the former iommu_domain_capable
function to just iommu_capable
- various fixes in handling RMRR ranges for the VT-d driver (one fix
requires a device driver core change which was acked by Greg KH)
- the AMD IOMMU driver now assigns and deassigns complete alias
groups to fix issues with devices using the wrong PCI request-id
- MMU-401 support for the ARM SMMU driver
- multi-master IOMMU group support for the ARM SMMU driver
- various other small fixes all over the place"
* tag 'iommu-updates-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits)
iommu/vt-d: Work around broken RMRR firmware entries
iommu/vt-d: Store bus information in RMRR PCI device path
iommu/vt-d: Only remove domain when device is removed
driver core: Add BUS_NOTIFY_REMOVED_DEVICE event
iommu/amd: Fix devid mapping for ivrs_ioapic override
iommu/irq_remapping: Fix the regression of hpet irq remapping
iommu: Fix bus notifier breakage
iommu/amd: Split init_iommu_group() from iommu_init_device()
iommu: Rework iommu_group_get_for_pci_dev()
iommu: Make of_device_id array const
amd_iommu: do not dereference a NULL pointer address.
iommu/omap: Remove omap_iommu unused owner field
iommu: Remove iommu_domain_has_cap() API function
IB/usnic: Convert to use new iommu_capable() API function
vfio: Convert to use new iommu_capable() API function
kvm: iommu: Convert to use new iommu_capable() API function
iommu/tegra: Convert to iommu_capable() API function
iommu/msm: Convert to iommu_capable() API function
iommu/vt-d: Convert to iommu_capable() API function
iommu/fsl: Convert to iommu_capable() API function
...
|
|
Add a function to create CMA region from previously reserved memory and
add support for handling 'shared-dma-pool' reserved-memory device tree
nodes.
Based on previous code provided by Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Initialization procedure of dma coherent pool has been split into two
parts, so memory pool can now be initialized without assigning to
particular struct device. Then initialized region can be assigned to more
than one struct device. To protect from concurent allocations from
structure. The last part of this patch adds support for handling
'shared-dma-pool' reserved-memory device tree nodes.
[akpm@linux-foundation.org: use more appropriate printk facility levels]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When kmalloc() fails, we should return -ENOMEM.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge patch-bomb from Andrew Morton:
- part of OCFS2 (review is laggy again)
- procfs
- slab
- all of MM
- zram, zbud
- various other random things: arch, filesystems.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
nosave: consolidate __nosave_{begin,end} in <asm/sections.h>
include/linux/screen_info.h: remove unused ORIG_* macros
kernel/sys.c: compat sysinfo syscall: fix undefined behavior
kernel/sys.c: whitespace fixes
acct: eliminate compile warning
kernel/async.c: switch to pr_foo()
include/linux/blkdev.h: use NULL instead of zero
include/linux/kernel.h: deduplicate code implementing clamp* macros
include/linux/kernel.h: rewrite min3, max3 and clamp using min and max
alpha: use Kbuild logic to include <asm-generic/sections.h>
frv: remove deprecated IRQF_DISABLED
frv: remove unused cpuinfo_frv and friends to fix future build error
zbud: avoid accessing last unused freelist
zsmalloc: simplify init_zspage free obj linking
mm/zsmalloc.c: correct comment for fullness group computation
zram: use notify_free to account all free notifications
zram: report maximum used memory
zram: zram memory size limitation
zsmalloc: change return value unit of zs_get_total_size_bytes
zsmalloc: move pages_allocated to zs_pool
...
|
|
It isn't obvious that CMA can be disabled on the kernel's command line, so
document it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chuck Ebbert <cebbert.lkml@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The deprecation warnings for the scan_unevictable interface triggers by
scripts doing `sysctl -a | grep something else'. This is annoying and not
helpful.
The interface has been defunct since 264e56d8247e ("mm: disable user
interface to manually rescue unevictable pages"), which was in 2011, and
there haven't been any reports of usecases for it, only reports that the
deprecation warnings are annying. It's unlikely that anybody is using
this interface specifically at this point, so remove it.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
