summaryrefslogtreecommitdiff
path: root/arch
AgeCommit message (Collapse)AuthorFilesLines
2025-12-30ARM: dts: microchip: lan966x: Fix the access to the PHYs for pcb8290Horatiu Vultur1-0/+1
The problem is that the MDIO controller can't detect any of the PHYs. The reason is that the lan966x is not pulling high the GPIO 53 that is connected to the PHYs reset GPIO. Without doing this the PHYs are kept in reset. The mdio controller framework has the possibility to control a GPIO to release the reset of the PHYs. So take advantage of this and set line to be high before accessing the PHYs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@tuxon.dev> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20251119134750.394655-1-horatiu.vultur@microchip.com [claudiu.beznea: add microchip in patch title, s/possiblity/possibility in patch description] Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
2025-12-30ARM: dts: imx: imx6sl: fix lcdif compatibleAndreas Kemnade1-1/+1
Fix lcdif compatible according to bindings doc. dtbs_check tested only, a glance at the datasheet shows that it should be the correct fallback compatible. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30ARM: imx_v6_v7_defconfig: enable EPD regulator needed for Kobo Clara 2eAndreas Kemnade1-0/+1
Kobo Clara 2e revision b requires the JD9930/FP9931 regulator driver for the EPD, so enable it. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30ARM: dts: imx: imx6sll-kobo-clara2e: add regulator for EPDAndreas Kemnade1-1/+60
Now there is a driver and binding for the JD9930, so add the information to the devicetree for revision b. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30ARM: dts: imx: imx6sll: fix lcdif compatibleAndreas Kemnade1-1/+1
Fix lcdif compatible according to bindings doc. dtbs_check tested only, a glance at the datasheet shows that it should be the correct fallback compatible. Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Add Apalis iMX8QPFrancesco Dolcini6-0/+95
Add support for the Apalis iMX8QP SoM mated with Apalis Ixora and Apalis Evaluation board. Apalis iMX8QP is a variant of the Apalis iMX8QM, using an NXP i.MX8QP SoC instead of the i.MX8QM. The two SoCs are pin to pin compatible, with the i.MX8QP being a lower end variant, with a slower GPU and one Cortex A72 core instead of two. The two Apalis SoMs variants share the same schematics and PCB, and the iMX8QP variant exists only on revision V1.1 of board. Link: https://www.nxp.com/products/i.MX8 Link: https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8 Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Add NXP i.MX8QP SoC dtsiFrancesco Dolcini1-0/+24
Add support for NXP i.MX8QP SoC, this is pin to pin compatible variant of the i.MX8QM, with a slower GPU and one Cortex A72 core instead of two. Link: https://www.nxp.com/products/i.MX8 Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8qm: Add CPU cluster labelsFrancesco Dolcini1-2/+2
Add labels to the cpu cluster nodes to prepare for the addition of the i.MX8QP SoC in which these nodes would need to be adjusted from another DT file. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Use lowercase hexKrzysztof Kozlowski21-75/+75
The DTS code coding style expects lowercase hex for values and unit addresses. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Minor whitespace cleanupKrzysztof Kozlowski4-7/+7
The DTS code coding style expects exactly one space around '=' and before '{' characters. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Use hyphen in node namesKrzysztof Kozlowski5-7/+7
DTS coding style prefers hyphens instead of underscores in the node names. Change should be safe, because node names are not considered an ABI. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx94: add mt35xu512aba spi nor supportHaibo Chen1-0/+34
Add mt35xu512aba spi nor support on imx943-evk board. This nor chip support OCT DTR mode. For the reset pin, since the nor chip side need 1.8v IO voltage for reset pin, but the IO expander side use 3.3v IO voltage, so to make circuit safe, need to config the pad as OPEN DRAIN. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx94: add xspi device nodeHaibo Chen1-1/+33
imx94 has two xspi, add these device nodes. Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Add i.MX952 EVK basic device treePeng Fan2-0/+219
Add i.MX952 EVK basic device tree, with UART1, SDHC[1,2] supported. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: Add initial device tree for i.MX952Peng Fan4-0/+2374
i.MX952 is designed for AI-powered sensor fusion and vision sensing applications, it features 4 Corte-A55, 1 Cortex-M33, 1 Cortex-M7 and NXP eIQ NPU and advanced graphics, video and advanced security with edgelock. Product info could be found at: https://www.nxp.com/products/i.MX-952 The basic device tree includes: - clock, pin, power header files - device nodes: CPU[0-3], SCMI firmware, Interrupt Controller, Sys counter, eDMA, MU, SPI, UART, I2C, USB and etc Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mm-phycore-som: Update eth phy impedanceTeresa Remmet1-0/+1
Update the DP83867 ethernet phy impedance settings to to optimize signal quality and reduce potential signal integrity issues. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: add support for NXP i.MX93 FRDMFabian Pflug2-0/+621
The FRDM i.MX 93 development board is a low-cost and compact development board featuring the i.MX93 applications processor. It features: - Dual Cortex-A55 - 2 GB LPDDR4X / LPDDR4 - 32 GB eMMC5.1 - MicroSD slot - GbE RJ45 x 2 - USB2.0 1x Type C, 1x Type A This file is based upon the one provided by nxp in their own kernel and yocto meta layer for the device, but adapted for mainline. Signed-off-by: Haidong Zheng <haidong.zheng@nxp.com> Signed-off-by: Danwei Luo <danwei.luo@nxp.com> Signed-off-by: Lei Xu <lei.xu@nxp.com> Signed-off-by: Fabian Pflug <f.pflug@pengutronix.de> Reviewed-by: Francesco Valla <francesco@valla.it> Tested-by: Francesco Valla <francesco@valla.it> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: mb-smarc-2: Add PCIe supportAlexander Stein2-3/+21
TQMa8XxS on MB-SMARC-2 supports mPCIe on X44. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30ARM: imx_v6_v7_defconfig: Configure CONFIG_SND_SOC_FSL_ASOC_CARD as moduleAlexander Stein1-1/+1
This option explicitly selects other options, e.g. SND_SOC_FSL_SAI. These SAI drivers use DMA which in turn is dependent on CONFIG_IMX_SDMA. SDMA needs a firmware which is not yet present if the driver is built-in. Thus build CONFIG_SND_SOC_FSL_ASOC_CARD to avoid useless driver probe deferrals due to missing DMA channels. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mn-tqma8mqnl: fix LDO5 power offMarkus Niebel2-6/+29
Fix SD card removal caused by automatic LDO5 power off after boot To prevent this, add vqmmc regulator for USDHC, using a GPIO-controlled regulator that is supplied by LDO5. Since this is implemented on SoM but used on baseboards with SD-card interface, implement the functionality on SoM part and optionally enable it on baseboards if needed. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mn-tqma8mqnl: remove virtual 1.8V regulatorMarkus Niebel1-9/+1
BUCK5 regulator supplies the 1.8V rail. Use the actual regulator instead of a virtual fixed regulator. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mn-tqma8mqnl: remove virtual 3.3V regulatorMarkus Niebel1-10/+3
BUCK4 rail supplies the 3.3V rail. Use the actual regulator instead of a virtual fixed regulator. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mm-tqma8mqml: fix LDO5 power offMarkus Niebel2-6/+29
Fix SD card removal caused by automatic LDO5 power off after boot. To prevent this, add vqmmc regulator for USDHC, using a GPIO-controlled regulator that is supplied by LDO5. Since this is implemented on SoM but used on baseboards with SD-card interface, implement the functionality on SoM part and optionally enable it on baseboards if needed. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mm-tqma8mqml: remove superfluous lineMarkus Niebel1-1/+0
Remove one empty line that is not needed. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mm-tqma8mqml: remove virtual 1.8V regulatorMarkus Niebel1-9/+1
BUCK5 regulator supplies the 1.8V rail. Use the actual regulator instead of a virtual fixed regulator. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mm-tqma8mqml: remove virtual 3.3V regulatorMarkus Niebel1-11/+3
BUCK4 rail supplies the 3.3V rail. Use the actual regulator instead of a virtual fixed regulator. Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: mba8mx: Fix Ethernet PHY IRQ supportAlexander Stein1-1/+1
Ethernet PHY interrupt mode is level triggered. Adjust the mode accordingly. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Fixes: 70cf622bb16e ("arm64: dts: mba8mx: Add Ethernet PHY IRQ support") Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-var-som: Add support for TSC2046 touchscreenStefano Radaelli1-0/+46
The VAR-SOM-MX8MP integrates a TSC2046 resistive touchscreen controller. The controller is physically located on the SOM, and its signals are routed to the SOM pins, allowing carrier boards to make use of it. This patch adds the TSC2046 node and the appropriate SPI controller. Signed-off-by: Stefano Radaelli <stefano.r@variscite.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-var-som: Add support for WM8904 audio codecStefano Radaelli1-0/+94
The VAR-SOM-MX8MP can integrate the WM8904, a high-performance ultra-low-power stereo codec optimized for portable audio applications. This patch adds the WM8904 device to the appropriate I2C bus, enables the SAI peripheral, and introduces the sound node to expose the sound card to the system. Signed-off-by: Stefano Radaelli <stefano.r@variscite.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-var-som: Add WiFi and Bluetooth supportStefano Radaelli1-0/+92
Add device tree nodes for the WiFi and Bluetooth module mounted on the VAR-SOM-MX8MP. The module can be based on either the NXP IW612 or IW611 chipset, depending on the configuration chosen by the customer. Regardless of the chipset used, WiFi communicates over SDIO and Bluetooth over UART. Signed-off-by: Stefano Radaelli <stefano.r@variscite.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-var-som: Move UART2 description to Symphony carrierStefano Radaelli2-18/+18
The VAR-SOM-MX8MP module does not provide an onboard debug console. UART2 is routed and exposed only on the Symphony carrier board, while custom carrier designs may choose to expose a different UART. Move the UART2 node from the SOM device tree to the imx8mp-var-som-symphony.dts, keeping the SOM dtsi limited to hardware present on the module itself. Signed-off-by: Stefano Radaelli <stefano.r@variscite.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-var-som: Move PCA9534 GPIO expander to Symphony carrierStefano Radaelli2-50/+50
The VAR-SOM-MX8MP module does not include the PCA9534 GPIO expander nor the LED connected to it. These components are present only on the Symphony carrier board and may vary across custom carrier designs. Move the PCA9534 GPIO expander node and the associated LED definition from the SOM device tree to the Symphony carrier DTS, ensuring the SOM dtsi describes only hardware present on the module. Signed-off-by: Stefano Radaelli <stefano.r@variscite.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-var-som: Move USDHC2 support to Symphony carrierStefano Radaelli2-75/+77
The VAR-SOM-MX8MP module does not include a microSD slot connected to USDHC2. The USDHC2 interface is routed only on the Symphony carrier board, and it may optionally be used or omitted depending on the customer's carrier design. Move the USDHC2 node, its regulators, pinctrl groups and related GPIOs from the SOM device tree to the Symphony carrier DTS, keeping the SOM description limited to hardware populated on the module. Signed-off-by: Stefano Radaelli <stefano.r@variscite.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx93-11x11-evk: Use phys to replace xceiver-supplyPeng Fan1-9/+8
The TJA1057 used on i.MX93 EVK is actually high-speed CAN transceiver, not a regulator supply. So use phys to reflect the truth. Reviewed-by: Frank Li <Frank.Li@nxp.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8mp-evk: Use phys to replace xceiver-supplyPeng Fan1-30/+13
The TJA1048 used on i.MX8MP-EVK is actually high-speed CAN transceiver, not a regulator supply. So use phys to reflect the truth. Reviewed-by: Frank Li <Frank.Li@nxp.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx95-15x15-evk: Use phys to replace xceiver-supplyPeng Fan1-7/+6
The TJA1051T/3 used on i.MX95-15x15-EVK is actually high-speed CAN transceiver, not a regulator supply. So use phys to reflect the truth. Reviewed-by: Frank Li <Frank.Li@nxp.com> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30ARM: dts: imx6qdl: Add default GIC address cellsAlexander Stein1-0/+1
Add missing address-cells 0 to GPC interrupt node to silence W=1 warning: imx6qdl.dtsi:281.4-284.29: Warning (interrupt_map): /soc/pcie@1ffc000:interrupt-map: Missing property '#address-cells' in node /soc/bus@2000000/gpc@20dc000, using 0 as fallback Value '0' is correct because: 1. GPC interrupt controller children are only power domains, 2. interrupt-map property (in PCI node) consists of five components and the fourth component "parent unit address", which size is defined by '#address-cells' of the node pointed to by the interrupt-parent component, is not used (=0) Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: imx8m{m,p}-venice-gw71xx: Add MagetometerTim Harvey2-0/+30
Add support for the optional LIS2MDL magnetometer on GW71xx baseboards. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mp-ras314: Add HDMI audio output supportAlexander Stein1-0/+15
Add the HDMI audio soundcard and enable necessary nodes. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mp-ras314: Fix HDMI CEC pad control settingsAlexander Stein1-1/+1
As per datasheet of the HDMI protection IC the CEC_IC pin has been configured as open-drain. Fixes: ddabb3ce3f90 ("arm64: dts: freescale: add TQMa8MPQL on MBa8MP-RAS314") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mp-ras314: Fix Ethernet PHY IRQ supportAlexander Stein1-2/+2
Ethernet PHY interrupt mode is level triggered. Adjust the mode accordingly. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mpxl: Configure IEEE 1588 event out signalAlexander Stein1-1/+2
The event out signal on channel 2 is available on pad SAI2_RXD0 which is connected to X63 pin 13. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mpxl: Add HDMI audio output supportAlexander Stein1-0/+15
Add the HDMI audio soundcard and enable necessary nodes. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mpxl: Fix HDMI CEC pad control settingsAlexander Stein1-1/+1
As per datasheet of the HDMI protection IC the CEC_IC pin has been configured as open-drain. Fixes: 418d1d840e42 ("arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mpxl: Fix Ethernet PHY IRQ supportAlexander Stein1-2/+2
Ethernet PHY interrupt mode is level triggered. Adjust the mode accordingly. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: tqma8mpql-mba8mpxl: Adjust copyright text formatAlexander Stein1-2/+3
Replace personal mail address by mailing list. Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: imx8mp-toradex-smarc: enable hdmi_pai deviceFrancesco Dolcini1-0/+4
Enable the hdmi_pai device on the Toradex SMARC iMX8M Plus Development boards. The hdmi_pai device, together with aud2htx module, hdmi_pai and hdmi controller compose the HDMI audio pipeline. See commit b21f87b8322f ("arm64: dts: imx8mp-evk: enable hdmi_pai device") for the equivalent change on the NXP i.MX8MP EVK board. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: imx8mp-verdin: enable hdmi_pai deviceFrancesco Dolcini4-0/+16
Enable the hdmi_pai device on the various iMX8M Plus Verdin boards that feature the related HDMI interface. The hdmi_pai device, together with aud2htx module, hdmi_pai and hdmi controller compose the HDMI audio pipeline. See commit b21f87b8322f ("arm64: dts: imx8mp-evk: enable hdmi_pai device") for the equivalent change on the NXP i.MX8MP EVK board. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: imx8mp-verdin: Remove obsolete TODO commentsFrancesco Dolcini1-4/+0
Remove obsolete TODO comments, I2S interface is supported since Linux v6.6. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2025-12-30arm64: dts: freescale: imx8-apalis: Add ethernet aliasFrancesco Dolcini1-0/+4
Add alias for the apalis first ethernet interface, this ensures consistent interface naming (e.g. `end0`) and this is used by the firmware to correctly set the MAC address. Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2026-05-26 19:24:25 +0300