| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"While testing Sasha Levin's 'kallsyms: embed source file:line info in
kernel stack traces' patch series, which increases the typical kernel
image size, I found some issues with the parisc initial kernel mapping
which may prevent the kernel to boot.
The three small patches here fix this"
* tag 'parisc-for-7.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix initial page table creation for boot
parisc: Check kernel mapping earlier at bootup
parisc: Increase initial mapping to 64 MB with KALLSYMS
|
|
On Pixel 6 (and Pro), a MAX77759 companion PMIC for USB Type-C
applications is used, which contains four functional blocks (at
distinct I2C addresses):
* top (including GPIO & NVMEM)
* charger
* fuel gauge
* TCPCi
This change adds the fuel gauge.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://patch.msgid.link/20260302-max77759-fg-dts-v2-1-12f1109a6fee@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a cleanup of arch/x86/kernel/head_64.S removing the pre-built page
tables for Xen guests
- a small comment update
- another cleanup for Xen PVH guests mode
- fix an issue with Xen PV-devices backed by driver domains
* tag 'for-linus-7.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/xenbus: better handle backend crash
xenbus: add xenbus_device parameter to xenbus_read_driver_state()
x86/PVH: Use boot params to pass RSDP address in start_info page
x86/xen: update outdated comment
xen/acpi-processor: fix _CST detection using undersized evaluation buffer
x86/xen: Build identity mapping page tables dynamically for XENPV
|
|
Use inout "+" asm constraint modifiers to simplify asm operands.
No functional changes intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: H. Peter Anvin (Intel) <hpa@zytor.com>
Link: https://patch.msgid.link/20251216105134.248196-1-ubizjak@gmail.com
|
|
The per-device MSI allocation calculation in pseries_irq_domain_alloc()
is clearly wrong. It can still happen to work when nr_irqs is 1.
Correct it.
Fixes: c0215e2d72de ("powerpc/pseries: Fix MSI-X allocation failure when quota is exceeded")
Cc: stable@vger.kernel.org
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Reviewed-by: Nilay Shroff <nilay@linux.ibm.com>
[maddy: Fixed Nilay's reviewed-by tag]
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260302003948.1452016-1-namcao@linutronix.de
|
|
This fixes dtschema warnings such as the following:
arch/powerpc/boot/dts/mpc8315erdb.dtb: /: memory: False schema
does not allow {'device_type': ['memory'], 'reg': [[0, 134217728]]}
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303-mpc83xx-cleanup-v2-5-187d3a13effa@posteo.net
|
|
These properties are required by the spi-controller binding.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303-mpc83xx-cleanup-v2-4-187d3a13effa@posteo.net
|
|
The leds-gpio.yaml schema requires that GPIO LED nodes contain "led",
and preferably start with "led-"
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303-mpc83xx-cleanup-v2-3-187d3a13effa@posteo.net
|
|
This increases readability, because "0x8" isn't very descriptive.
mpc8315erdb.dtb remains identical after this patch.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303-mpc83xx-cleanup-v2-2-187d3a13effa@posteo.net
|
|
This increases readability, because "0x8" isn't very descriptive.
mpc8313erdb.dtb remains identical after this patch.
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303-mpc83xx-cleanup-v2-1-187d3a13effa@posteo.net
|
|
When kmeter.c was refactored into km83xx.c in 2011, the "keymile" vendor
prefix was changed to upper-case "Keymile". The devicetree at
arch/powerpc/boot/dts/kmeter1.dts never underwent the same change,
suggesting that this was simply a mistake.
Fixes: 93e2b95c81042d ("powerpc/83xx: rename and update kmeter1")
Signed-off-by: J. Neuschäfer <j.ne@posteo.net>
Reviewed-by: Heiko Schocher <hs@nabladev.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303-keymile-v1-1-463a11e71702@posteo.net
|
|
Commit 61688a82e047 ("powerpc/bpf: enable kfunc call") inadvertently
enabled kfunc call support for 32-bit powerpc but that support will
not be possible until ABI mismatch between 32-bit powerpc and eBPF is
handled in 32-bit powerpc JIT code. Till then, advertise support only
for 64-bit powerpc. Also, in powerpc ABI, caller needs to extend the
arguments properly based on signedness. The JIT code is responsible
for handling this explicitly for kfunc calls as verifier can't handle
this for each architecture-specific ABI needs. But this was not taken
care of while kfunc call support was enabled for powerpc. Fix it by
handling this with bpf_jit_find_kfunc_model() and using zero_extend()
& sign_extend() helper functions.
Fixes: 61688a82e047 ("powerpc/bpf: enable kfunc call")
Cc: stable@vger.kernel.org
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303181031.390073-7-hbathini@linux.ibm.com
|
|
Exception callback reuses the stack frame of exception boundary. When
exception boundary and exception callback programs have different BPF
stack depth, the current stack unwind in exception callback will fail.
Adjust the stack frame size of exception callback, in its prologue,
if its BPF stack depth is different from that of exception boundary.
Reported-by: bot+bpf-ci@kernel.org
Closes: https://lore.kernel.org/bpf/2a310e86a59eb4c44c3ac9e5647814469d9c955580c9c0f1b3d9ca4a44717a34@mail.kernel.org/
Fixes: 11d45eee9f42 ("powerpc64/bpf: Additional NVR handling for bpf_throw")
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303181031.390073-6-hbathini@linux.ibm.com
|
|
Since bpf2bpf tailcall support is enabled for 64-bit powerpc with
kernel commit 2ed2d8f6fb38 ("powerpc64/bpf: Support tailcalls with
subprogs"), 'tailcalls/tailcall_bpf2bpf_hierarchy_fexit' BPF selftest
is triggering "corrupted stack end detected inside scheduler" with the
config option CONFIG_SCHED_STACK_END_CHECK enabled. While reviewing
the stack layout for BPF trampoline, observed that the dummy frame is
trying to protect the redzone of BPF program. This is because tail
call info and NVRs save area are in redzone at the time of tailcall
as the current BPF program stack frame is teared down before the
tailcall. But saving this redzone in the dummy frame of trampoline
is unnecessary because of the follow reasons:
1) Firstly, trampoline can be attached to BPF entry/main program
or subprog. But prologue part of the BPF entry/main program,
where the trampoline attachpoint is, is skipped during tailcall.
So, protecting the redzone does not arise when the trampoline is
not even triggered in this scenario.
2) In case of subprog, the caller's stackframe is already setup
and the subprog's stackframe is yet to be setup. So, nothing
on the redzone to be protected.
Also, using dummy frame in BPF trampoline, wastes critically scarce
kernel stack space, especially in tailcall sequence, for marginal
benefit in stack unwinding. So, drop setting up the dummy frame.
Instead, save return address in bpf trampoline frame and use it as
appropriate. Pruning this unnecessary stack usage mitigates the
likelihood of stack overflow in scenarios where bpf2bpf tailcalls
and fexit programs are mixed.
Reported-by: Saket Kumar Bhaskar <skb99@linux.ibm.com>
Fixes: 2ed2d8f6fb38 ("powerpc64/bpf: Support tailcalls with subprogs")
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303181031.390073-5-hbathini@linux.ibm.com
|
|
Ideally, the offset used to load the tail call info field and to find
the pass by reference address for tail call field should be the same.
But while setting up the tail call info in the trampoline, this was
not followed. This can be misleading and can lead to unpredictable
results if and when bpf_has_stack_frame() ends up returning true
for trampoline frame. Since commit 15513beeb673 ("powerpc64/bpf:
Moving tail_call_cnt to bottom of frame") and commit 2ed2d8f6fb38
("powerpc64/bpf: Support tailcalls with subprogs") ensured tail call
field is at the bottom of the stack frame for BPF programs as well as
BPF trampoline, avoid relying on bpf_jit_stack_tailcallinfo_offset()
and bpf_has_stack_frame() for trampoline frame and always calculate
tail call field offset with reference to older frame.
Fixes: 2ed2d8f6fb38 ("powerpc64/bpf: Support tailcalls with subprogs")
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303181031.390073-4-hbathini@linux.ibm.com
|
|
bpf_get_func_ip() helper function returns the address of the traced
function. It relies on the IP address stored at ctx - 16 by the bpf
trampoline. On 64-bit powerpc, this address is recovered from LR
accounting for OOL trampoline. But the address stored here was off
by 4-bytes. Ensure the address is the actual start of the traced
function.
Reported-by: Abhishek Dubey <adubey@linux.ibm.com>
Fixes: d243b62b7bd3 ("powerpc64/bpf: Add support for bpf trampolines")
Cc: stable@vger.kernel.org
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303181031.390073-3-hbathini@linux.ibm.com
|
|
Do not increment tailcall count, if tailcall did not succeed due to
missing BPF program.
Fixes: ce0761419fae ("powerpc/bpf: Implement support for tail calls")
Cc: stable@vger.kernel.org
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260303181031.390073-2-hbathini@linux.ibm.com
|
|
Support for -fpatchable-function-entry on ppc64le was added in Clang
with [1]. However, when no prefix NOPs are specified - as is the case
with CONFIG_PPC_FTRACE_OUT_OF_LINE - the first NOP is emitted at LEP,
but Clang records the Global Entry Point (GEP) unlike GCC which does
record the Local Entry Point (LEP). Issue [2] has been raised to align
Clang's behavior with GCC. As a temporary workaround to ensure ftrace
initialization works as expected with Clang, derive the LEP using
ppc_function_entry() for kernel symbols and by looking for the below
module GEP sequence for module addresses, until [2] is resolved:
ld r2, -8(r12)
add r2, r2, r12
[1] https://github.com/llvm/llvm-project/pull/151569
[2] https://github.com/llvm/llvm-project/issues/163706
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260127084926.34497-4-hbathini@linux.ibm.com
|
|
The total number of out-of-line (OOL) stubs required for function
tracing is determined using the following command:
$(OBJDUMP) -r -j __patchable_function_entries vmlinux.o
While this works correctly with GNU objdump, llvm-objdump does not
list the expected relocation records for this section. Fix this by
using the -d option and counting R_PPC64_ADDR64 relocation entries.
This works as desired with both objdump and llvm-objdump.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260127084926.34497-3-hbathini@linux.ibm.com
|
|
ARCH_USING_PATCHABLE_FUNCTION_ENTRY depends on toolchain support for
-fpatchable-function-entry option. The current script that checks
for this support only handles GCC. Rename the script and extend it
to detect support for -fpatchable-function-entry with Clang as well,
allowing clean cross-compilation with Clang toolchains.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Tested-by: Venkat Rao Bagalkote <venkat88@linux.ibm.com>
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Link: https://patch.msgid.link/20260127084926.34497-2-hbathini@linux.ibm.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux
Pull Kbuild fixes from Nathan Chancellor:
- Split out .modinfo section from ELF_DETAILS macro, as that macro may
be used in other areas that expect to discard .modinfo, breaking
certain image layouts
- Adjust genksyms parser to handle optional attributes in certain
declarations, necessary after commit 07919126ecfc ("netfilter:
annotate NAT helper hook pointers with __rcu")
- Include resolve_btfids in external module build created by
scripts/package/install-extmod-build when it may be run on external
modules
- Avoid removing objtool binary with 'make clean', as it is required
for external module builds
* tag 'kbuild-fixes-7.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Leave objtool binary around with 'make clean'
kbuild: install-extmod-build: Package resolve_btfids if necessary
genksyms: Fix parsing a declarator with a preceding attribute
kbuild: Split .modinfo out from ELF_DETAILS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix stackleak and xor lib inline asm, constraints and clobbers to
prevent miscompilations and incomplete stack poisoning
* tag 's390-7.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/stackleak: Fix __stackleak_poison() inline assembly constraint
s390/xor: Improve inline assembly constraints
s390/xor: Fix xor_xc_2() inline assembly constraints
s390/xor: Fix xor_xc_5() inline assembly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main changes are a fix to the way in which we manage the access
flag setting for mappings using the contiguous bit and a fix for a
hang on the kexec/hibernation path.
Summary:
- Fix kexec/hibernation hang due to bogus read-only mappings
- Fix sparse warnings in our cmpxchg() implementation
- Prevent runtime-const being used in modules, just like x86
- Fix broken elision of access flag modifications for contiguous
entries on systems without support for hardware updates
- Fix a broken SVE selftest that was testing the wrong instruction"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
selftest/arm64: Fix sve2p1_sigill() to hwcap test
arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults
arm64: make runtime const not usable by modules
arm64: mm: Add PTE_DIRTY back to PAGE_KERNEL* to fix kexec/hibernation
arm64: Silence sparse warnings caused by the type casting in (cmp)xchg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Initialize msi_addr_mask for OF-created PCI devices to fix sparc and
powerpc probe regressions (Nilay Shroff)
- Orphan the Altera PCIe controller driver (Dave Hansen)
* tag 'pci-v7.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: Orphan Altera PCIe controller driver
sparc/PCI: Initialize msi_addr_mask for OF-created PCI devices
powerpc/pci: Initialize msi_addr_mask for OF-created PCI devices
|
|
Refresh the defconfig for Renesas ARM systems:
- Move various DRM config symbols (moved in commit 22ba3bb3ff2a8e5a
("drm/Kconfig: sort driver Kconfig source list")),
- Drop CONFIG_NFS_V4_1=y (removed in commit 7537db24806fdc3d ("NFS:
Merge CONFIG_NFS_V4_1 with CONFIG_NFS_V4")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/d5faca8fe1db69d584f3097c269be7813ceffd33.1772449420.git.geert+renesas@glider.be
|
|
RZ/N2H (R9A09G087) has three DMA controllers that can be used by
peripherals like SPI to offload data transfers from the CPU.
Wire up the DMA channels for the SPI peripherals.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260128215132.1353381-4-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
RZ/T2H (R9A09G077) has three DMA controllers that can be used by
peripherals like SPI to offload data transfers from the CPU.
Wire up the DMA channels for the SPI peripherals.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260128215132.1353381-3-cosmin-gabriel.tanislav.xa@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable RTC.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260125192706.27099-6-ovidiu.panait.rb@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add RTC node to Renesas RZ/V2N ("R9A09G056") SoC DTSI.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260125192706.27099-5-ovidiu.panait.rb@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on Ebisu
board. The clock generator supplies 100 MHz differential clock for both
PCIe slot and BT/WLAN expansion port, as well as for the USB 3.0 PHY.
This configuration is valid for SW49 in OFF position, which means the
PCIe signals are routed to the PCIe slot and U11 9FGV0841 PCIe clock
generator output 3 supplies clock to the PCIe slot.
In case the SW49 is set to ON position, which means the PCIe signals
are routed to the EX BT/WLAN expansion port, and U11 9FGV0841 PCIe
clock generator output 4 supplies clock to the port and &pciec0_rp
clocks should be changed to "clocks = <&pcie_usb_clk 4>;". Once the
BT/WLAN port is tested, this can be implemented using a DTO. Until
then, assume SW49 is set to OFF position.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-10-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on ULCB
boards. The clock generator supplies 100 MHz differential clock for
both PCIe ports, the USB 3.0 PHY and SATA.
SATA is not yet described in the ULCB DT, therefore the connection to
this clock generator is not described here either.
The H3 ULCB schematic does describe connection from output DIF7 to
USB3S1_CLK_*, but these signals do not exist on the SoC, therefore
this connection is also not described.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-9-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Describe the 9FGV0841 PCIe and USB3.0 clock generator present on both
Salvator-X and Salvator-XS boards. The clock generator supplies 100 MHz
differential clock for both PCIe ports, as well as for the USB 3.0 PHY.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-8-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add USB 3.0 PHY and PHY clock node for R-Car E3. The PHY node is
different in that it does not have control registers and extal clock,
which are not routed to the SoC pads on R-Car E3, therefore describe the
PHY as usb-nop-xceiv simple PHY. Add USB3S0 clock pad fixed-clock node,
the frequency has to be overridden at board level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-7-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add node which describes the root port in the PCIe controller DT node.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-6-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-5-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-4-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-3-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add nodes which describe the root ports in the PCIe controller DT nodes.
This can be used together with the pwrctrl driver to control clock and
power supply to a PCIe slot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260118135038.8033-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
In RZ/N1 SoCs, CPUs are allowed to work at 125, 250 or 500 MHz when the
'ref' clock frequency value is set to 500 MHz which is the default 'ref'
clock frequency value.
Add support for CPU frequency scaling defining those 3 frequencies in
the opp-table with the assumption that the 'ref' clock is set to its
default value.
Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260115164905.1203453-1-herve.codina@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The U-Boot SPL is responsible for initializing the hardware and it does
also initialize HSCIF0 and its pinmux, mark the HSCIF0 pinmux as needed
in all bootloader stages. The SPL also uses OTP to determine the exact
V4H SoC variant during DRAM initialization, to determine which is the
maximum allowed DRAM rate, mark OTP as required in all bootloader stages
as well.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260112234642.225993-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
SPI interrupts are in the range 0-987. Extended SPI interrupts should
use GIC_ESPI, instead of abusing GIC_SPI with a manual offset of 4064.
Fixes: 63500d12cf76d003 ("arm64: dts: renesas: Add R8A78000 SoC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/1f9dd274720ea1b66617a5dd84f76c3efc829dc8.1772641415.git.geert+renesas@glider.be
|
|
The default settings for the Versa3 device on the Renesas RZ/G3S SMARC
SoM board have PLL2 disabled. PLL2 was later enabled together with audio
support, as it is required to support both 44.1 kHz and 48 kHz audio.
With PLL2 enabled, it was observed that Linux occasionally either hangs
during boot (the last log message being related to the I2C probe) or
randomly crashes. This was mainly reproducible on cold boots. During
debugging, it was also noticed that the Unicode replacement character (�)
sometimes appears on the serial console. Further investigation traced this
to the configuration applied through the Versa3 register at offset 0x1c,
which controls PLL enablement.
The appearance of the Unicode replacement character suggested an issue
with the SoC reference clock. The RZ/G3S reference clock is provided by
the Versa3 clock generator (REF output).
After checking with the Renesas Versa3 hardware team, it was found that
this is related to the PLL2 lock bit being set through the
renesas,settings DT property.
The PLL lock bit must be set to avoid unstable clock output from the PLL.
However, due to the Versa3 hardware design, when a PLL lock bit is set,
all outputs (including the REF clock) are temporarily disabled until the
configured PLLs become stable.
As an alternative, the bypass bit can be used. This does not interrupt the
PLL2 output or any other Versa3 outputs, but it may result in temporary
instability on PLL2 output while the configuration is applied. Since PLL2
feeds only the audio path and audio is not used during early boot, this is
acceptable and does not affect system boot.
Drop the PLL2 lock bit and set the bypass bit instead.
This has been tested with more than 1000 cold boots.
Fixes: a94253232b04 ("arm64: dts: renesas: rzg3s-smarc-som: Add versa3 clock generator node")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260302135703.162601-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The CPG register regions were incorrectly sized. Update them to match
the actual hardware specification:
- First region (0x80280000): 0x1000 -> 0x10000 (64kiB)
- Second region (0x81280000): 0x9000 -> 0x10000 (64kiB)
Fixes: 4b3d31f0b81fe ("arm64: dts: renesas: Add initial SoC DTSI for the RZ/N2H SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260213131742.3606334-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The CPG register regions were incorrectly sized. Update them to match
the actual hardware specification:
- First region (0x80280000): 0x1000 -> 0x10000 (64kiB)
- Second region (0x81280000): 0x9000 -> 0x10000 (64kiB)
Fixes: d17b34744f5e4 ("arm64: dts: renesas: Add initial support for the Renesas RZ/T2H SoC")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260213131742.3606334-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The HW user manual for the Renesas RZ/V2H(P) SoC (a.k.a r9a09g057)
states that only WDT1 is supposed to be accessed by the CA55 cores.
WDT0 is supposed to be used by the CM33 core, WDT2 is supposed
to be used by the CR8 core 0, and WDT3 is supposed to be used
by the CR8 core 1.
Remove wdt{0,2,3} from the SoC specific device tree to make it
compliant with the specification from the HW manual.
This change is harmless as there are currently no users of the
wdt{0,2,3} device tree nodes, only the wdt1 node is actually used.
Fixes: 095105496e7d ("arm64: dts: renesas: r9a09g057: Add WDT0-WDT3 nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260203124247.7320-3-fabrizio.castro.jz@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Set an appropriate ramp delay for the SD0 I/O voltage regulator in the
CN15 SD overlay to make UHS-I voltage switching reliable during card
initialization.
This issue was observed on the RZ/V2H EVK, while the same UHS-I cards
worked on the RZ/V2N EVK without problems. Adding the ramp delay makes
the behavior consistent and avoids SD init timeouts.
Before this change SD0 could fail with:
mmc0: error -110 whilst initialising SD card
With the delay in place UHS-I cards enumerate correctly:
mmc0: new UHS-I speed SDR104 SDXC card at address aaaa
mmcblk0: mmc0:aaaa SR64G 59.5 GiB
mmcblk0: p1
Fixes: 3d6c2bc7629c8 ("arm64: dts: renesas: Add CN15 eMMC and SD overlays for RZ/V2H and RZ/V2N EVKs")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260123225957.1007089-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add a ramp delay of 60 uV/us to the vqmmc_sdhi0 voltage regulator to
fix UHS-I SD card detection failures.
Measurements on CN78 pin 4 showed the actual voltage ramp time to be
21.86ms when switching between 3.3V and 1.8V. A 25ms ramp delay has
been configured to provide adequate margin. The calculation is based
on the voltage delta of 1.5V (3.3V - 1.8V):
1500000 uV / 60 uV/us = 25000 us (25ms)
Prior to this patch, UHS-I cards failed to initialize with:
mmc0: error -110 whilst initialising SD card
After this patch, UHS-I cards are properly detected on SD0:
mmc0: new UHS-I speed SDR104 SDXC card at address aaaa
mmcblk0: mmc0:aaaa SR64G 59.5 GiB
Fixes: d065453e5ee09 ("arm64: dts: renesas: rzt2h-rzn2h-evk: Enable SD card slot")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20260123225957.1007089-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
In some scenarios, a deadlock can happen, involving _do_shadow_pte().
Convert all usages of pgste_get_lock() to pgste_get_trylock() in
_do_shadow_pte() and return -EAGAIN. All callers can already deal with
-EAGAIN being returned.
Fixes: e38c884df921 ("KVM: s390: Switch to new gmap")
Tested-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Christoph Schlameuss <schlameuss@linux.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
|
|
contpte_ptep_set_access_flags() compared the gathered ptep_get() value
against the requested entry to detect no-ops. ptep_get() ORs AF/dirty
from all sub-PTEs in the CONT block, so a dirty sibling can make the
target appear already-dirty. When the gathered value matches entry, the
function returns 0 even though the target sub-PTE still has PTE_RDONLY
set in hardware.
For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may
set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered
across the CONT range. But page-table walkers that evaluate each
descriptor individually (e.g. a CPU without DBM support, or an SMMU
without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the
unchanged target sub-PTE, causing an infinite fault loop.
Gathering can therefore cause false no-ops when only a sibling has been
updated:
- write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared)
- read faults: target still lacks PTE_AF
Fix by checking each sub-PTE against the requested AF/dirty/write state
(the same bits consumed by __ptep_set_access_flags()), using raw
per-PTE values rather than the gathered ptep_get() view, before
returning no-op. Keep using the raw target PTE for the write-bit unfold
decision.
Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT
range may become the effective cached translation and software must
maintain consistent attributes across the range.
Fixes: 4602e5757bcc ("arm64/mm: wire up PTE_CONT for user mappings")
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Zi Yan <ziy@nvidia.com>
Cc: Breno Leitao <leitao@debian.org>
Cc: stable@vger.kernel.org
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: James Houghton <jthoughton@google.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Piotr Jaroszynski <pjaroszynski@nvidia.com>
Acked-by: Balbir Singh <balbirs@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We already have an ISB in __kvm_at() to make the address translation result
visible to subsequent reads of PAR_EL1. Remove the redundant one right
after it.
Signed-off-by: Zenghui Yu (Huawei) <zenghui.yu@linux.dev>
Link: https://patch.msgid.link/20260306074422.47694-1-zenghui.yu@linux.dev
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
