Age | Commit message (Collapse) | Author | Files | Lines |
|
crypto node should use the "crypto" generic naming,
and not a specific one ("sahara", "dcp", "caam").
Child nodes of the crypto node for caam crypto engine
should use the "jr" name (without an index),
as indicated in the DT binding.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW5910-C revision adds a TI CC1352 connected to IMX UART4
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We need to indicate that powering off the TI WiFi is safe, to avoid:
wl18xx_driver wl18xx.2.auto: Unbalanced pm_runtime_enable!
wl1271_sdio mmc0:0001:2: wl12xx_sdio_power_on: failed to get_sync(-13)
which prevents the WiFi being functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The pmic is a mfd device and supports gpios. Those gpios are not routed
to the SoM baseboard pin header but they are connected to the i.MX6. We
need the GPIO's to configure the pmic to select between the
suspend/resume arm and soc voltages
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
By default the phycore-som has support for two watchdog devices: 1st the
internal imx6 watchdog and 2nd the DA9062 PMIC watchdog. According [1]
the PMIC watchdog is used as boot watchdog. It is common to use this
watchdog during "system up" time too. Furthermore the PMIC watchdog can
be used to address ERR007117 since the phycore-som can be equipped with
NAND or eMMC storage.
The PMIC watchdog can be enabled/disabled by the PMIC itself if the PMIC
enters POWERDOWN mode or by the host. The PMIC powerdown mode can't be
used due to the PCB design. So the watchdog is still enabled during a
suspend which causes a system reset. We need to tell the driver to
disable the watchdog during a system suspend and to reenable it upon a
resume to fix this.
[1] https://git.pengutronix.de/cgit/barebox/tree/arch/arm/dts/imx6qdl-phytec-phycore-som.dtsi#n73
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "pinctrl" instead of "iomuxc"
for all i.MX6/7 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX7, the SNVS requires a clock. This is similar to the clock
bound to the SNVS RTC node, but if the SNVS RTC driver isn't enabled,
then SNVS doesn't work, and as such the pwrkey driver doesn't
work (i.e. hangs the kernel, as the clock isn't enabled).
Also see commit ec2a844ef7c1
("ARM: dts: imx7s: add snvs rtc clock")
for a similar fix.
Signed-off-by: André Draszik <git@andred.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCI support.
Since this board has an active high PCI reset line, pass the
'reset-gpio-active-high' property.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "ocotp-ctrl" instead of "ocotp"
for all i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "watchdog" instead of "wdog" for
wdog nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the Toradex Aster carrier board.
Follow the usual hierarchic include model, maintaining shared
configuration imx7-colibri-aster.dtsi.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace boiler plate licenses texts with the SPDX license identifiers in
Colibri iMX7 DTS files.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
UART pins
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use new pin names containing DCE/DTE for UART RX/TX/RTS/CTS pins, this
is to distinguish the DCE/DTE functions.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Some of UART RTS/CTS pins' DCE/DTE mux function are missing,
add them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add DCE/DTE to UART pins macro defines to distinguish the
DCE and DTE functions, keep old defines at the end of file
for some time to make it backward compatible.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "clock-controller" instead of
"ccm" for clks node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "keypad" instead of "kpp" for kpp node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add fxos8700 iio imu entries for Gateworks ventana SBCs.
Signed-off-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "timer" instead of "gpt" for gpt node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per devicetree specification, generic names
are recommended to be used, such as bus.
i.MX AIPS is a AHB - IP bridge bus, so
we could use bus as node name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/boot/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/boot/dts/vf*.dtsi
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds defines for another cspi3 configuration.
The defines have been tested on an out-of-tree board.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
USB_C_DET pin shouldn't be in ethernet group.
Creating a separate group allows one to use this pin
as an USB ID pin.
Fixes: b326629f25b7 ("ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D suppor")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Make sure that the priority of the RTCs is defined.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The max voltage of SW1A is 3.3V on PF3000 as per
http://cache.freescale.com/files/analog/doc/data_sheet/PF3000.pdf?fsrch=1&sr=1&pageNum=1
While at it, remove the unnecessary leading zero from
the i2c address.
Signed-off-by: André Draszik <git@andred.net>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add Colibri SODIMM numbers as GPIO line names on module level. The GPIO
lines with a name are all available on the SODIMM edge connector of the
Colibri iMX7 module and therefore a customer might use it as a GPIO. The
Toradex Evaluation Board has the SODIMM numbers printed on the silk-
screen. This allows a customer to quickly control a GPIO on a pin-header
by using the name printed next to it.
Putting the GPIO line name on module level makes sure that a customer
gets a reasonable default. If more meaningful names are available on a
custom carrier board, the user can overwrite the line names in a carrier
board level device tree.
The eMMC based modules share all GPIO names except two GPIOs on bank 6
which are not available on the raw NAND devices. Hence overwrite GPIO
line names of bank 6 in the eMMC specific device tree file.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
At imx7ulp evk, all USBOTG1 OC (Over Current) function pins are
used by others, and the USB driver doesn't support OC function
through the GPIO, so we disable the OC function for this board
as well as delete the pinctrl for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
"simple-panel" is a Linux driver and has never been an accepted upstream
compatible string, so remove it.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After reset the oc protection polarity is set to active high on imx6.
If the polarity is not specified in device tree it is not changed.
The imx6dl-yapp4 platform uses an active-low oc signal so explicitly
configure that in the device tree.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a DT node for various voltage supply rails connected to SoC's ADC
for voltage monitoring purposes.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a DT node for various voltage supply rails connected to SoC's ADC
for voltage monitoring purposes.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a DT node for various voltage supply rails connected to SoC's ADC
for voltage monitoring purposes.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a DT node for various voltage supply rails connected to SoC's ADC
for voltage monitoring purposes.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add a DT node for various voltage supply rails connected to SoC's ADC
for voltage monitoring purposes.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the USB host port on the APx4 development board.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Documentation/devicetree/bindings/display/mxsfb.txt states that
the current display bindings format used in this dts is deprecated.
Convert it to the preferred DRM bindings instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem:
- Provision only ACPI enabled redistributors on GICv3
- Use the proper command colums when building the INVALL command for
the GICv3-ITS
- Ensure the allocation of the L2 vPE table for GICv4.1
- Correct the GICv4.1 VPROBASER programming so it uses the proper
size
- A set of small GICv4.1 tidy up patches
- Configuration cleanup for C-SKY interrupt chip
- Clarify the function documentation for irq_set_wake() to document
that the wakeup functionality is orthogonal to the irq
disable/enable mechanism"
* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
irqchip/gic-v3-its: Remove superfluous WARN_ON
irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
genirq: Clarify that irq wake state is orthogonal to enable/disable
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
irqchip: Some Kconfig cleanup for C-SKY
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix for a EFI boot regression on X86 which was caused by the
recent rework of the EFI memory map parsing. On systems with invalid
memmap entries the cleanup function uses an value which cannot be
relied on in this stage. Use the actual EFI memmap entry instead"
* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix boot regression on systems with invalid memmap entries
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix an existing bug in our user access handling, exposed by one of
the bug fixes we merged this cycle.
- A fix for a boot hang on 32-bit with CONFIG_TRACE_IRQFLAGS and the
recently added CONFIG_VMAP_STACK.
Thanks to: Christophe Leroy, Guenter Roeck.
* tag 'powerpc-5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix CONFIG_TRACE_IRQFLAGS with CONFIG_VMAP_STACK
powerpc/futex: Fix incorrect user access blocking
|
|
Pull ARM SoC late updates from Olof Johansson:
"This is some material that we picked up into our tree late, or that
had more complex dependencies on more than one topic branch that makes
sense to keep separately.
- TI support for secure accelerators and hwrng on OMAP4/5
- TI camera changes for dra7 and am437x and SGX improvement due to
better reset control support on am335x, am437x and dra7
- Davinci moves to proper clocksource on DM365, and regulator/audio
improvements for DM365 and DM644x eval boards"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (32 commits)
ARM: dts: omap4-droid4: Enable hdq for droid4 ds250x 1-wire battery nvmem
ARM: dts: motorola-cpcap-mapphone: Configure calibration interrupt
ARM: dts: Configure interconnect target module for am437x sgx
ARM: dts: Configure sgx for dra7
ARM: dts: Configure rstctrl reset for am335x SGX
ARM: dts: dra7: Add ti-sysc node for VPE
ARM: dts: dra7: add vpe clkctrl node
ARM: dts: am43x-epos-evm: Add VPFE and OV2659 entries
ARM: dts: am437x-sk-evm: Add VPFE and OV2659 entries
ARM: dts: am43xx: add support for clkout1 clock
arm: dts: dra76-evm: Add CAL and OV5640 nodes
arm: dtsi: dra76x: Add CAL dtsi node
arm: dts: dra72-evm-common: Add entries for the CSI2 cameras
ARM: dts: DRA72: Add CAL dtsi node
ARM: dts: dra7-l4: Add ti-sysc node for CAM
ARM: OMAP: DRA7xx: Make CAM clock domain SWSUP only
ARM: dts: dra7: add cam clkctrl node
ARM: OMAP2+: Drop legacy platform data for omap4 des
ARM: OMAP2+: Drop legacy platform data for omap4 sham
ARM: OMAP2+: Drop legacy platform data for omap4 aes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: configs: at91: enable MMC_SDHCI_OF_AT91 and MICROCHIP_PIT64B
arm64: defconfig: Enable Broadcom's GENET Ethernet controller
ARM: multi_v7_defconfig: Enable devfreq thermal integration
ARM: exynos_defconfig: Enable devfreq thermal integration
ARM: multi_v7_defconfig: Enable NFS v4.1 and v4.2
ARM: exynos_defconfig: Enable NFS v4.1 and v4.2
arm64: defconfig: Enable Actions Semi specific drivers
arm64: defconfig: Enable Broadcom's STB PCIe controller
arm64: defconfig: Enable CONFIG_CLK_IMX8MP by default
ARM: configs: at91: enable config flags for sam9x60 SoC
ARM: configs: at91: use savedefconfig
arm64: defconfig: Enable tegra XUDC support
ARM: defconfig: gemini: Update defconfig
arm64: defconfig: enable CONFIG_ARM_QCOM_CPUFREQ_NVMEM
arm64: defconfig: enable CONFIG_QCOM_CPR
arm64: defconfig: Enable HFPLL
arm64: defconfig: Enable CRYPTO_DEV_FSL_CAAM
ARM: imx_v6_v7_defconfig: Select the TFP410 driver
ARM: imx_v6_v7_defconfig: Enable NFS_V4_1 and NFS_V4_2 support
arm64: defconfig: Enable ATH10K_SNOC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
|
|
Pull ARM Device-tree updates from Olof Johansson:
"New SoCs:
- Atmel/Microchip SAM9X60 (ARM926 SoC)
- OMAP 37xx gets split into AM3703/AM3715/DM3725, who are all
variants of it with different GPU/media IP configurations.
- ST stm32mp15 SoCs (1-2 Cortex-A7, CAN, GPU depending on SKU)
- ST Ericsson ab8505 (variant of ab8500) and db8520 (variant of
db8500)
- Unisoc SC9863A SoC (8x Cortex-A55 mobile chipset w/ GPU, modem)
- Qualcomm SC7180 (8-core 64bit SoC, unnamed CPU class)
New boards:
- Allwinner:
+ Emlid Neutis SoM (H3 variant)
+ Libre Computer ALL-H3-IT
+ PineH64 Model B
- Amlogic:
+ Libretech Amlogic GX PC (s905d and s912-based variants)
- Atmel/Microchip:
+ Kizboxmini, sam9x60 EK, sama5d27 Wireless SOM (wlsom1)
- Marvell:
+ Armada 385-based SolidRun Clearfog GTR
- NXP:
+ Gateworks GW59xx boards based on i.MX6/6Q/6QDL
+ Tolino Shine 3 eBook reader (i.MX6sl)
+ Embedded Artists COM (i.MX7ULP)
+ SolidRun CLearfog CX/ITX and HoneyComb (LX2160A-based systems)
+ Google Coral Edge TPU (i.MX8MQ)
- Rockchip:
+ Radxa Dalang Carrier (supports rk3288 and rk3399 SOMs)
+ Radxa Rock Pi N10 (RK3399Pro-based)
+ VMARC RK3399Pro SOM
- ST:
+ Reference boards for stm32mp15
- ST Ericsson:
+ Samsung Galaxy S III mini (GT-I8190)
+ HREF520 reference board for DB8520
- TI OMAP:
+ Gen1 Amazon Echo (OMAP3630-based)
- Qualcomm:
+ Inforce 6640 Single Board Computer (msm8996-based)
+ SC7180 IDP (SC7180-based)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (623 commits)
dt-bindings: fix compilation error of the example in marvell,mmp3-hsic-phy.yaml
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
ARM: dts: aspeed: rainier: Add UCD90320 power sequencer
ARM: dts: aspeed: rainier: Switch PSUs to unknown version
arm64: dts: rockchip: Kill off "simple-panel" compatibles
ARM: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
ARM: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: exynos: Rename Samsung and Exynos to lowercase
arm64: dts: uniphier: add reset-names to NAND controller node
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"Most of these are smaller fixes that have accrued, and some continued
cleanup of OMAP platforms towards shared frameworks.
One new SoC from Atmel/Microchip: sam9x60"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: OMAP2+: Fix undefined reference to omap_secure_init
ARM: s3c64xx: Drop unneeded select of TIMER_OF
ARM: exynos: Drop unneeded select of MIGHT_HAVE_CACHE_L2X0
ARM: s3c24xx: Switch to atomic pwm API in rx1950
ARM: OMAP2+: sleep43xx: Call secure suspend/resume handlers
ARM: OMAP2+: Use ARM SMC Calling Convention when OP-TEE is available
ARM: OMAP2+: Introduce check for OP-TEE in omap_secure_init()
ARM: OMAP2+: Add omap_secure_init callback hook for secure initialization
ARM: at91: Documentation: add sam9x60 product and datasheet
ARM: at91: pm: use of_device_id array to find the proper shdwc node
ARM: at91: pm: use SAM9X60 PMC's compatible
ARM: imx: only select ARM_ERRATA_814220 for ARMv7-A
ARM: zynq: use physical cpuid in zynq_slcr_cpu_stop/start
ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume
ARM: tegra: Modify reshift divider during LP1
ARM: tegra: Enable PLLP bypass during Tegra124 LP1
ARM: samsung: Rename Samsung and Exynos to lowercase
ARM: exynos: Correct the help text for platform Kconfig option
ARM: bcm: Select ARM_AMBA for ARCH_BRCMSTB
ARM: brcmstb: Add debug UART entry for 7216
...
|