| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit df35c6e9027cf9affe699e632a48082ab1bbba4c ]
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0df3c7d7a73d75153090637392c0b73a63cdc24a ]
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b0aba467c329a89e8b325eda0cf60776958353fe ]
The spdif input and output of g12 and sm1 are compatible but
sm1 should use the related compatible since it exists.
Fixes: 86f2159468d5 ("arm64: dts: meson-sm1: add spdifin and pdifout nodes")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20240625111845.928192-1-jbrunet@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0f2ddb128fa20f8441d903285632f2c69e90fae1 ]
The VOP on RK3328 needs to run at a higher rate in order to produce a
proper 3840x2160 signal.
Change to use 300MHz for VIO clk and 400MHz for VOP clk, same rates used
by vendor 4.4 kernel.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240615170417.3134517-2-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02f838b7f8cdfb7a96b7f08e7f6716f230bdecba ]
Follow the example of other platforms and specify core_clk frequencies
in the frequency table in addition to the core_clk_src frequencies. The
driver should be setting the leaf frequency instead of some interim
clock freq.
Suggested-by: Nitin Rawat <quic_nitirawa@quicinc.com>
Fixes: 57fc67ef0d35 ("arm64: dts: qcom: msm8996: Add ufs related nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240408-msm8996-fix-ufs-v4-1-ee1a28bf8579@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 12c3ec878cbe3709782e85b88124abecc3bb8617 ]
Update WiFi SDIO and BT UART related props to better reflect details
about the optional onboard RTL8723DS WiFi/BT module.
Also correct the compatible used for bluetooth to match the WiFi/BT
module used on the board.
Fixes: bc3753aed81f ("arm64: dts: rockchip: rock-pi-s add more peripherals")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-14-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b64ed510ed946a4e4ca6d51d6512bf5361f6a04 ]
Be explicit about the Ethernet port and define mdio and ethernet-phy
nodes in the device tree for ROCK Pi S.
Fixes: bc3753aed81f ("arm64: dts: rockchip: rock-pi-s add more peripherals")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-8-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7affb86ef62581e3475ce3e0a7640da1f2ee29f8 ]
UAR0 CTS/RTS is not wired to any pin and is not used for the default
serial console use of UART0 on ROCK Pi S.
Override the SoC defined pinctrl props to limit configuration of the
two xfer pins wired to one of the GPIO pin headers.
Fixes: 2e04c25b1320 ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-6-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fc0daeccc384233eadfa9d5ddbd00159653c6bdc ]
Add cap-mmc-highspeed to allow use of high speed MMC mode using an eMMC
to uSD board. Use disable-wp to signal that no physical write-protect
line is present. Also add vcc_io used for card and IO line power as
vmmc-supply.
Fixes: 2e04c25b1320 ("arm64: dts: rockchip: add ROCK Pi S DTS support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20240521211029.1236094-5-jonas@kwiboo.se
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 98a0c4f2278b4d6c1c7722735c20b2247de6293f ]
15 qcom platform DTSI files define an adreno_smmu node.
msm8998 is the only one with adreno_smmu disabled by default.
There's no reason why this SMMU should be disabled by default,
it doesn't need any further configuration.
Bring msm8998 in line with the 14 other platforms.
This fixes GPU init failing with ENODEV:
msm_dpu c901000.display-controller: failed to load adreno gpu
msm_dpu c901000.display-controller: failed to bind 5000000.gpu (ops a3xx_ops): -19
Fixes: 87cd46d68aeac8 ("Configure Adreno GPU and related IOMMU")
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/be51d1a4-e8fc-48d1-9afb-a42b1d6ca478@freebox.fr
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c1aefeae8cb7b71c1bb6d33b1bda7fc322094e16 ]
The USB PHYs don't use extcon connectors, drop the extcon property from
the hsusb_phy1 node.
Fixes: 46680fe9ba61 ("arm64: dts: qcom: msm8996: Add support for the Xiaomi MSM8996 platform")
Cc: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-13-f1fd15c33fb3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27d3f57cf5a71484ea38770d4bfd10f6ef035cf4 ]
The UFS PHY is powered on via the UFS_PHY_GDSC power domain. Add
corresponding power-domain the the PHY node.
Fixes: 07fa917a335e ("arm64: dts: qcom: sm8450: add ufs nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-11-f1fd15c33fb3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 154ed5ea328d8a97a4ef5d1447e6f06d11fe2bbe ]
The UFS PHY is powered on via the UFS_PHY_GDSC power domain. Add
corresponding power-domain the the PHY node.
Fixes: b7e2fba06622 ("arm64: dts: qcom: sm8250: Add UFS controller and PHY")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-9-f1fd15c33fb3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba865bdcc688932980b8e5ec2154eaa33cd4a981 ]
Change the UFS QMP PHY to use newer style of QMP PHY bindings (single
resource region, no per-PHY subnodes).
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231205032552.1583336-8-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Stable-dep-of: 154ed5ea328d ("arm64: dts: qcom: sm8250: add power-domain to UFS PHY")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 18c2727282c5264ff5502daac26c43000e8eb202 ]
The UFS PHY is powered on via the UFS_PHY_GDSC power domain. Add
corresponding power-domain the the PHY node.
Fixes: 5a814af5fc22 ("arm64: dts: qcom: sm6350: Add UFS nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-8-f1fd15c33fb3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd39ae8b9bc10419b1e4b849cdbc6755a967ade1 ]
The UFS PHY is powered on via the UFS_PHY_GDSC power domain. Add
corresponding power-domain the the PHY node.
Fixes: cc16687fbd74 ("arm64: dts: qcom: sdm845: add UFS controller")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240501-qcom-phy-fixes-v1-6-f1fd15c33fb3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7821fa101eab529521aa4b724bf708149d70820c ]
iosf_mbi_pci_{read,write}_mdr() use pci_{read,write}_config_dword()
that return PCIBIOS_* codes but functions also return -ENODEV which are
not compatible error codes. As neither of the functions are related to
PCI read/write functions, they should return normal errnos.
Convert PCIBIOS_* returns code using pcibios_err_to_errno() into normal
errno before returning it.
Fixes: 46184415368a ("arch: x86: New MailBox support driver for Intel SOC's")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240527125538.13620-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9d7b435dfaec58432f4106aaa632bf39f52ce9f ]
xen_pcifront_enable_irq() uses pci_read_config_byte() that returns
PCIBIOS_* codes. The error handling, however, assumes the codes are
normal errnos because it checks for < 0.
xen_pcifront_enable_irq() also returns the PCIBIOS_* code back to the
caller but the function is used as the (*pcibios_enable_irq) function
which should return normal errnos.
Convert the error check to plain non-zero check which works for
PCIBIOS_* return codes and convert the PCIBIOS_* return code using
pcibios_err_to_errno() into normal errno before returning it.
Fixes: 3f2a230caf21 ("xen: handled remapped IRQs when enabling a pcifront PCI device.")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240527125538.13620-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 724852059e97c48557151b3aa4af424614819752 ]
intel_mid_pci_irq_enable() uses pci_read_config_byte() that returns
PCIBIOS_* codes. The error handling, however, assumes the codes are
normal errnos because it checks for < 0.
intel_mid_pci_irq_enable() also returns the PCIBIOS_* code back to the
caller but the function is used as the (*pcibios_enable_irq) function
which should return normal errnos.
Convert the error check to plain non-zero check which works for
PCIBIOS_* return codes and convert the PCIBIOS_* return code using
pcibios_err_to_errno() into normal errno before returning it.
Fixes: 5b395e2be6c4 ("x86/platform/intel-mid: Make IRQ allocation a bit more flexible")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240527125538.13620-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ec0b4c4d45cf7cf9a6c9626a494a89cb1ae7c645 ]
x86_of_pci_irq_enable() returns PCIBIOS_* code received from
pci_read_config_byte() directly and also -EINVAL which are not
compatible error types. x86_of_pci_irq_enable() is used as
(*pcibios_enable_irq) function which should not return PCIBIOS_* codes.
Convert the PCIBIOS_* return code from pci_read_config_byte() into
normal errno using pcibios_err_to_errno().
Fixes: 96e0a0797eba ("x86: dtb: Add support for PCI devices backed by dtb nodes")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20240527125538.13620-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 31ade7d4fdcf382beb8cb229a1f5d77e0f239672 ]
Discard and Write Zeroes are different operation and implemented
by different fallocate opcodes for ubd. If one fails the other one
can work and vice versa.
Split the code to disable the operations in ubd_handler to only
disable the operation that actually failed.
Fixes: 50109b5a03b4 ("um: Add support for DISCARD in the UBD Driver")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5db755fbb1a0de4a4cfd5d5edfaa19853b9c56e6 ]
Instead of a separate handler function that leaves no work in the
interrupt hanler itself, split out a per-request end I/O helper and
clean up the coding style and variable naming while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Link: https://lore.kernel.org/r/20240531074837.1648501-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 31ade7d4fdcf ("ubd: untagle discard vs write zeroes not support handling")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 45547a0a93d85f704b49788cde2e1d9ab9cd363b upstream.
With CONFIG_FSL_IFC now being user-visible, and thus changed from a select
to depends in CONFIG_MTD_NAND_FSL_IFC, the dependencies needs to be
selected in defconfigs.
Depends-on: 9ba0cae3cac0 ("memory: fsl_ifc: Make FSL_IFC config visible and selectable")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240530-fsl-ifc-config-v3-2-1fd2c3d233dd@geanix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fad58a41b84667cb6c9232371fc3af77d4443889 upstream.
For Gen-1 targets like SDM630, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for SDM630 to mitigate this issue.
Cc: stable@vger.kernel.org
Fixes: c65a4ed2ea8b ("arm64: dts: qcom: sdm630: Add USB configuration")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240704152848.3380602-5-quic_kriskura@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4ae4837871ee8c8b055cf8131f65d31ee4208fa0 upstream.
For Gen-1 targets like IPQ6018, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for IPQ6018 to mitigate this issue.
Cc: stable@vger.kernel.org
Fixes: 20bb9e3dd2e4 ("arm64: dts: qcom: ipq6018: add usb3 DT description")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240704152848.3380602-2-quic_kriskura@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 44ea1ae3cf95db97e10d6ce17527948121f1dd4b upstream.
For Gen-1 targets like MSM8996, it is seen that stressing out the
controller in host mode results in HC died error:
xhci-hcd.12.auto: xHCI host not responding to stop endpoint command
xhci-hcd.12.auto: xHCI host controller not responding, assume dead
xhci-hcd.12.auto: HC died; cleaning up
And at this instant only restarting the host mode fixes it. Disable
SuperSpeed instance in park mode for MSM8996 to mitigate this issue.
Cc: stable@vger.kernel.org
Fixes: 1e39255ed29d ("arm64: dts: msm8996: Add device node for qcom,dwc3")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240704152848.3380602-8-quic_kriskura@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 24d3ba0a7b44c1617c27f5045eecc4f34752ab03 upstream.
The 32-bit ARM kernel stops working if the kernel grows to the point
where veneers for __get_user_* are created.
AAPCS32 [1] states, "Register r12 (IP) may be used by a linker as a
scratch register between a routine and any subroutine it calls. It
can also be used within a routine to hold intermediate values between
subroutine calls."
However, bl instructions buried within the inline asm are unpredictable
for compilers; hence, "ip" must be added to the clobber list.
This becomes critical when veneers for __get_user_* are created because
veneers use the ip register since commit 02e541db0540 ("ARM: 8323/1:
force linker to use PIC veneers").
[1]: https://github.com/ARM-software/abi-aa/blob/2023Q1/aapcs32/aapcs32.rst
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: John Stultz <jstultz@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 393da6cbb2ff89aadc47683a85269f913aa1c139 ]
ftrace_graph_ret_addr() takes an `idx` integer pointer that is used to
optimize the stack unwinding. Pass it a valid pointer to utilize the
optimizations that might be available in the future.
The commit is making riscv's usage of ftrace_graph_ret_addr() match
x86_64.
Signed-off-by: Puranjay Mohan <puranjay@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20240618145820.62112-1-puranjay@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a1216e62d039bf63a539bbe718536ec789a853dd ]
If a PCI device is removed during eeh_pe_report_edev(), edev->pdev
will change and can cause a crash, hold the PCI rescan/remove lock
while taking a copy of edev->pdev->bus.
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240617140240.580453-1-ganeshgr@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a14150e1656f7a332a943154fc486504db4d586 ]
Reading the dispatch trace log from /sys/kernel/debug/powerpc/dtl/cpu-*
results in a BUG() when the config CONFIG_HARDENED_USERCOPY is enabled as
shown below.
kernel BUG at mm/usercopy.c:102!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Radix SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: xfs libcrc32c dm_service_time sd_mod t10_pi sg ibmvfc
scsi_transport_fc ibmveth pseries_wdt dm_multipath dm_mirror dm_region_hash dm_log dm_mod fuse
CPU: 27 PID: 1815 Comm: python3 Not tainted 6.10.0-rc3 #85
Hardware name: IBM,9040-MRX POWER10 (raw) 0x800200 0xf000006 of:IBM,FW1060.00 (NM1060_042) hv:phyp pSeries
NIP: c0000000005d23d4 LR: c0000000005d23d0 CTR: 00000000006ee6f8
REGS: c000000120c078c0 TRAP: 0700 Not tainted (6.10.0-rc3)
MSR: 8000000000029033 <SF,EE,ME,IR,DR,RI,LE> CR: 2828220f XER: 0000000e
CFAR: c0000000001fdc80 IRQMASK: 0
[ ... GPRs omitted ... ]
NIP [c0000000005d23d4] usercopy_abort+0x78/0xb0
LR [c0000000005d23d0] usercopy_abort+0x74/0xb0
Call Trace:
usercopy_abort+0x74/0xb0 (unreliable)
__check_heap_object+0xf8/0x120
check_heap_object+0x218/0x240
__check_object_size+0x84/0x1a4
dtl_file_read+0x17c/0x2c4
full_proxy_read+0x8c/0x110
vfs_read+0xdc/0x3a0
ksys_read+0x84/0x144
system_call_exception+0x124/0x330
system_call_vectored_common+0x15c/0x2ec
--- interrupt: 3000 at 0x7fff81f3ab34
Commit 6d07d1cd300f ("usercopy: Restrict non-usercopy caches to size 0")
requires that only whitelisted areas in slab/slub objects can be copied to
userspace when usercopy hardening is enabled using CONFIG_HARDENED_USERCOPY.
Dtl contains hypervisor dispatch events which are expected to be read by
privileged users. Hence mark this safe for user access.
Specify useroffset=0 and usersize=DISPATCH_LOG_BYTES to whitelist the
entire object.
Co-developed-by: Vishal Chourasia <vishalc@linux.ibm.com>
Signed-off-by: Vishal Chourasia <vishalc@linux.ibm.com>
Signed-off-by: Anjali K <anjalik@linux.ibm.com>
Reviewed-by: Srikar Dronamraju <srikar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240614173844.746818-1-anjalik@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d5679a0aae2d8cda72169452c32e5cb88a7ab33 ]
This is almost compatible, but passing a negative offset should result
in a EINVAL error, but on mips o32 compat mode would seek to a large
32-bit byte offset.
Use compat_sys_lseek() to correctly sign-extend the argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a986fa57fd81a1430e00b3c6cf8a325d6f894a63 ]
Al reported a possible use-after-free (UAF) in kvm_spapr_tce_attach_iommu_group().
It looks up `stt` from tablefd, but then continues to use it after doing
fdput() on the returned fd. After the fdput() the tablefd is free to be
closed by another thread. The close calls kvm_spapr_tce_release() and
then release_spapr_tce_table() (via call_rcu()) which frees `stt`.
Although there are calls to rcu_read_lock() in
kvm_spapr_tce_attach_iommu_group() they are not sufficient to prevent
the UAF, because `stt` is used outside the locked regions.
With an artifcial delay after the fdput() and a userspace program which
triggers the race, KASAN detects the UAF:
BUG: KASAN: slab-use-after-free in kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm]
Read of size 4 at addr c000200027552c30 by task kvm-vfio/2505
CPU: 54 PID: 2505 Comm: kvm-vfio Not tainted 6.10.0-rc3-next-20240612-dirty #1
Hardware name: 8335-GTH POWER9 0x4e1202 opal:skiboot-v6.5.3-35-g1851b2a06 PowerNV
Call Trace:
dump_stack_lvl+0xb4/0x108 (unreliable)
print_report+0x2b4/0x6ec
kasan_report+0x118/0x2b0
__asan_load4+0xb8/0xd0
kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm]
kvm_vfio_set_attr+0x524/0xac0 [kvm]
kvm_device_ioctl+0x144/0x240 [kvm]
sys_ioctl+0x62c/0x1810
system_call_exception+0x190/0x440
system_call_vectored_common+0x15c/0x2ec
...
Freed by task 0:
...
kfree+0xec/0x3e0
release_spapr_tce_table+0xd4/0x11c [kvm]
rcu_core+0x568/0x16a0
handle_softirqs+0x23c/0x920
do_softirq_own_stack+0x6c/0x90
do_softirq_own_stack+0x58/0x90
__irq_exit_rcu+0x218/0x2d0
irq_exit+0x30/0x80
arch_local_irq_restore+0x128/0x230
arch_local_irq_enable+0x1c/0x30
cpuidle_enter_state+0x134/0x5cc
cpuidle_enter+0x6c/0xb0
call_cpuidle+0x7c/0x100
do_idle+0x394/0x410
cpu_startup_entry+0x60/0x70
start_secondary+0x3fc/0x410
start_secondary_prolog+0x10/0x14
Fix it by delaying the fdput() until `stt` is no longer in use, which
is effectively the entire function. To keep the patch minimal add a call
to fdput() at each of the existing return paths. Future work can convert
the function to goto or __cleanup style cleanup.
With the fix in place the test case no longer triggers the UAF.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Closes: https://lore.kernel.org/all/20240610024437.GA1464458@ZenIV/
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240614122910.3499489-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ac8b270b61d48fcc61f052097777e3b5e11591e0 ]
When BHI mitigation is enabled, if SYSENTER is invoked with the TF flag set
then entry_SYSENTER_compat() uses CLEAR_BRANCH_HISTORY and calls the
clear_bhb_loop() before the TF flag is cleared. This causes the #DB handler
(exc_debug_kernel()) to issue a warning because single-step is used outside the
entry_SYSENTER_compat() function.
To address this issue, entry_SYSENTER_compat() should use CLEAR_BRANCH_HISTORY
after making sure the TF flag is cleared.
The problem can be reproduced with the following sequence:
$ cat sysenter_step.c
int main()
{ asm("pushf; pop %ax; bts $8,%ax; push %ax; popf; sysenter"); }
$ gcc -o sysenter_step sysenter_step.c
$ ./sysenter_step
Segmentation fault (core dumped)
The program is expected to crash, and the #DB handler will issue a warning.
Kernel log:
WARNING: CPU: 27 PID: 7000 at arch/x86/kernel/traps.c:1009 exc_debug_kernel+0xd2/0x160
...
RIP: 0010:exc_debug_kernel+0xd2/0x160
...
Call Trace:
<#DB>
? show_regs+0x68/0x80
? __warn+0x8c/0x140
? exc_debug_kernel+0xd2/0x160
? report_bug+0x175/0x1a0
? handle_bug+0x44/0x90
? exc_invalid_op+0x1c/0x70
? asm_exc_invalid_op+0x1f/0x30
? exc_debug_kernel+0xd2/0x160
exc_debug+0x43/0x50
asm_exc_debug+0x1e/0x40
RIP: 0010:clear_bhb_loop+0x0/0xb0
...
</#DB>
<TASK>
? entry_SYSENTER_compat_after_hwframe+0x6e/0x8d
</TASK>
[ bp: Massage commit message. ]
Fixes: 7390db8aea0d ("x86/bhi: Add support for clearing branch history at syscall entry")
Reported-by: Suman Maity <suman.m.maity@oracle.com>
Signed-off-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/20240524070459.3674025-1-alexandre.chartre@oracle.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eb43c9b1517b48e2ff0d3a584aca197338987d7b ]
This comment comes from a time when the kernel attempted to use SYSRET
on all returns to userspace, including interrupts and exceptions. Ever
since commit fffbb5dc ("Move opportunistic sysret code to syscall code
path"), SYSRET is only used for returning from system calls. The
specific tracing issue listed in this comment is not possible anymore.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/20230721161018.50214-2-brgerst@gmail.com
Stable-dep-of: ac8b270b61d4 ("x86/bhi: Avoid warning in #DB handler due to BHI mitigation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
The linux-6.1-y backport of commit b377c66ae350 ("x86/retpoline: Add
NOENDBR annotation to the SRSO dummy return thunk") misplaced the new
NOENDBR annotation, repeating the annotation on __x86_return_thunk,
rather than adding the annotation to the !CONFIG_CPU_SRSO version of
srso_alias_untrain_ret, as intended.
Move the annotation to the right place.
Fixes: b377c66ae350 ("x86/retpoline: Add NOENDBR annotation to the SRSO dummy return thunk")
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acc3815db1a02d654fbc19726ceaadca0d7dd81c ]
Replace a comma between expression statements by a semicolon.
Fixes: efc1bb8a6fd5 ("davinci: add power management support")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7278a8fb8d032dfdc03d9b5d17e0bc451cdc1492 ]
Without __unitialized, the following code is generated when
INIT_STACK_ALL_ZERO is enabled:
86: d7 0f f0 a0 f0 a0 xc 160(16,%r15), 160(%r15)
8c: e3 40 f0 a0 00 24 stg %r4, 160(%r15)
92: c0 10 00 00 00 08 larl %r1, 0xa2
98: e3 10 f0 a8 00 24 stg %r1, 168(%r15)
9e: b2 b2 f0 a0 lpswe 160(%r15)
The xc is not adding any security because psw is fully initialized
with the following instructions. Add __unitialized to the psw
definitiation to avoid the superfluous clearing of psw.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit d201c92bff90f3d3d0b079fc955378c15c0483cc upstream.
Correct the specified regulator-min-microvolt value for the buck DCDC_REG2
regulator, which is part of the Rockchip RK809 PMIC, in the Pine64 Quartz64
Model B board dts. According to the RK809 datasheet, version 1.01, this
regulator is capable of producing voltages as low as 0.5 V on its output,
instead of going down to 0.9 V only, which is additionally confirmed by the
regulator-min-microvolt values found in the board dts files for the other
supported boards that use the same RK809 PMIC.
This allows the DVFS to clock the GPU on the Quartz64 Model B below 700 MHz,
all the way down to 200 MHz, which saves some power and reduces the amount of
generated heat a bit, improving the thermal headroom and possibly improving
the bursty CPU and GPU performance on this board.
This also eliminates the following warnings in the kernel log:
core: _opp_supported_by_regulators: OPP minuV: 825000 maxuV: 825000, not supported by regulator
panfrost fde60000.gpu: _opp_add: OPP not supported by regulators (200000000)
core: _opp_supported_by_regulators: OPP minuV: 825000 maxuV: 825000, not supported by regulator
panfrost fde60000.gpu: _opp_add: OPP not supported by regulators (300000000)
core: _opp_supported_by_regulators: OPP minuV: 825000 maxuV: 825000, not supported by regulator
panfrost fde60000.gpu: _opp_add: OPP not supported by regulators (400000000)
core: _opp_supported_by_regulators: OPP minuV: 825000 maxuV: 825000, not supported by regulator
panfrost fde60000.gpu: _opp_add: OPP not supported by regulators (600000000)
Fixes: dcc8c66bef79 ("arm64: dts: rockchip: add Pine64 Quartz64-B device tree")
Cc: stable@vger.kernel.org
Reported-By: Diederik de Haas <didi.debian@cknow.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Tested-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/e70742ea2df432bf57b3f7de542d81ca22b0da2f.1716225483.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 21a741eb75f80397e5f7d3739e24d7d75e619011 upstream.
kexec on pseries disables AIL (reloc_on_exc), required for scv
instruction support, before other CPUs have been shut down. This means
they can execute scv instructions after AIL is disabled, which causes an
interrupt at an unexpected entry location that crashes the kernel.
Change the kexec sequence to disable AIL after other CPUs have been
brought down.
As a refresher, the real-mode scv interrupt vector is 0x17000, and the
fixed-location head code probably couldn't easily deal with implementing
such high addresses so it was just decided not to support that interrupt
at all.
Fixes: 7fa95f9adaee ("powerpc/64s: system call support for scv/rfscv instructions")
Cc: stable@vger.kernel.org # v5.9+
Reported-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Closes: https://lore.kernel.org/3b4b2943-49ad-4619-b195-bc416f1d1409@linux.ibm.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Gautam Menghani <gautam@linux.ibm.com>
Tested-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Link: https://msgid.link/20240625134047.298759-1-npiggin@gmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c562ba719df570c986caf0941fea2449150bcbc4 ]
If the kexec crash code is called in the interrupt context, the
machine_kexec_mask_interrupts() function will trigger a deadlock while
trying to acquire the irqdesc spinlock and then deactivate irqchip in
irq_set_irqchip_state() function.
Unlike arm64, riscv only requires irq_eoi handler to complete EOI and
keeping irq_set_irqchip_state() will only leave this possible deadlock
without any use. So we simply remove it.
Link: https://lore.kernel.org/linux-riscv/20231208111015.173237-1-songshuaishuai@tinylab.org/
Fixes: b17d19a5314a ("riscv: kexec: Fixup irq controller broken in kexec crash path")
Signed-off-by: Song Shuai <songshuaishuai@tinylab.org>
Reviewed-by: Ryo Takakura <takakura@valinux.co.jp>
Link: https://lore.kernel.org/r/20240626023316.539971-1-songshuaishuai@tinylab.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4c6abb7f7b349f00c0f7ed5045bf67759c012892 ]
in rare cases, e.g. for injecting a machine check we do intercept all
load PSW instructions via ICTL_LPSW. With facility 193 a new variant
LPSWEY was added. KVM needs to handle that as well.
Fixes: a3efa8429266 ("KVM: s390: gen_facilities: allow facilities 165, 193, 194 and 196")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Message-ID: <20240628163547.2314-1-borntraeger@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8873aab8646194a4446117bb617cc71bddda2dee ]
All these commands end up peeking into the PACA using the user
originated cpu id as an index. Check the cpu id is valid in order
to prevent xmon to crash. Instead of printing an error, this follows
the same behavior as the "lp s #" command : ignore the buggy cpu id
parameter and fall back to the #-less version of the command.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/161531347060.252863.10490063933688958044.stgit@bahia.lan
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit be140f1732b523947425aaafbe2e37b41b622d96 ]
There is code that builds with calls to IO accessors even when
CONFIG_PCI=n, but the actual calls are guarded by runtime checks.
If not those calls would be faulting, because the page at virtual
address zero is (usually) not mapped into the kernel. As Arnd pointed
out, it is possible a large port value could cause the address to be
above mmap_min_addr which would then access userspace, which would be
a bug.
To avoid any such issues, set _IO_BASE to POISON_POINTER_DELTA. That
is a value chosen to point into unmapped space between the kernel and
userspace, so any access will always fault.
Note that on 32-bit POISON_POINTER_DELTA is 0, so the patch only has an
effect on 64-bit.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240503075619.394467-2-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0db880fc865ffb522141ced4bfa66c12ab1fbb70 ]
nmi_enter()/nmi_exit() touches per cpu variables which can lead to kernel
crash when invoked during real mode interrupt handling (e.g. early HMI/MCE
interrupt handler) if percpu allocation comes from vmalloc area.
Early HMI/MCE handlers are called through DEFINE_INTERRUPT_HANDLER_NMI()
wrapper which invokes nmi_enter/nmi_exit calls. We don't see any issue when
percpu allocation is from the embedded first chunk. However with
CONFIG_NEED_PER_CPU_PAGE_FIRST_CHUNK enabled there are chances where percpu
allocation can come from the vmalloc area.
With kernel command line "percpu_alloc=page" we can force percpu allocation
to come from vmalloc area and can see kernel crash in machine_check_early:
[ 1.215714] NIP [c000000000e49eb4] rcu_nmi_enter+0x24/0x110
[ 1.215717] LR [c0000000000461a0] machine_check_early+0xf0/0x2c0
[ 1.215719] --- interrupt: 200
[ 1.215720] [c000000fffd73180] [0000000000000000] 0x0 (unreliable)
[ 1.215722] [c000000fffd731b0] [0000000000000000] 0x0
[ 1.215724] [c000000fffd73210] [c000000000008364] machine_check_early_common+0x134/0x1f8
Fix this by avoiding use of nmi_enter()/nmi_exit() in real mode if percpu
first chunk is not embedded.
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Shirisha Ganta <shirisha@linux.ibm.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240410043006.81577-1-mahesh@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d7ec44aa5d1eb94a30319074762a1740440cdc8 ]
Add the missing #sound-dai-cells for RK3368's I2S and S/PDIF controllers.
Fixes: f7d89dfe1e31 ("arm64: dts: rockchip: add i2s nodes support for RK3368 SoCs")
Fixes: 0328d68ea76d ("arm64: dts: rockchip: add rk3368 spdif node")
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240623090116.670607-4-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 02afd3d5b9fa4ffed284c0f7e7bec609097804fc ]
use GPIO0_A2 as interrupt pin for PMIC. GPIO2_A6 was used for
pre-production board.
Fixes: b918e81f2145 ("arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://lore.kernel.org/r/20240619050047.1217-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cca46f811d0000c1522a5e18ea48c27a15e45c05 ]
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc78062477 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
