| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
do_undefinstr currently does not expect undefined instructions in kernel
code, since it always uses get_user() to read the instruction.
Dereference the 'pc' pointer directly in the SVC case.
Per Nicolas Pitre's note, kernel code is never in thumb mode.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Implement a custom ioremap implementation for iop3xx. This saves
establishing new mappings. It also cleans up the PCI IO resource to be a
physical address rather than a virtual address as Russell pointed out on
the original iop13xx port.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
bad_mode() currently prints the mode which caused the exception, and
then causes an oops dump to be printed which again displays this
information (since the CPSR in the struct pt_regs is correct.) This
leads to processor_modes[] being shared between traps.c and process.c
with a local declaration of it.
We can clean this up by moving processor_modes[] to process.c and
removing the duplication, resulting in processor_modes[] becoming
static.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Contec Micro9 (H/M/L) boards based on Cirrus Logic ep93xx (ep9315/ep9307/ep9302).
Signed-off-by: Manfred Gruber <m.gruber@tirol.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds the platform resources required to support the
ixp4xx-pata-cf libata driver on Avila Gateworks boards.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds support for the Gateworks Avila Network Platform in
a separate set of setup files to the IXDP425. This is necessary now
that a driver for the Avila CF card slot is available. It also adds
support for a minor variant on the Avila board known as the Loft,
which has a different number of maximum PCI devices.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch removes references to the Gateworks Avila Network
Platform in the ixdp425 setup code. Avila setup should occur
separately now that a CF ATA device driver is available.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the glue for ARM11 SMP oprofile support, which also supports the
performance monitor in the coherency unit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add oprofile glue for ARM11 (ARMv6) oprofile support. This
connects the ARM11 core profiling support to the oprofile code
for uniprocessor configurations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add basic support for the ARM11 profiling hardware. This is shared
between the ARM11 UP and ARM11 SMP oprofile support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When calling into the EFI firmware, the parameters need to be passed on
the stack. The recent change to use -mregparm=3 breaks x86 EFI support.
This patch is needed to allow the new Intel-based Macs to suspend to ram
(efi.get_time is called during the suspend phase).
Signed-off-by: Frederic Riss <frederic.riss@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The SN Altix platform does not conform to the IOSAPIC IRQ routing model.
Add code in acpi_unregister_gsi() to check if (acpi_irq_model ==
ACPI_IRQ_MODEL_PLATFORM) and return.
Due to an oversight, this code was not added previously when
similar code was added to acpi_register_gsi().
http://marc.theaimsgroup.com/?l=linux-acpi&m=116680983430121&w=2
Signed-off-by: John Keller <jpk@sgi.com>
Acked-by: Len Brown <lenb@kernel.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes up ia64 kexec support for HP rx2620 hardware. It does
this by skipping migration of already disabled irqs. This is most likely a
problem on other ia64 platforms as well, but I've only been able to
reproduce it on one machine so far.
The full story is that handle_bad_irq() gets invoked before starting the
new kernel without this patch. This seems to happen when fixup_irqs()
calls generic_handle_irq() on already migrated (and disabled) irqs. So by
avoiding migration of disabled irqs we stay away of handle_bad_irq().
The code has been tested on three different ia64 machines, all with good
results. It is possible to trigger the same bug by offlining a processor
using echo 0 > /sys/devices/system/cpu/cpuX/online.
More detailed information is available in the following mail thread:
http://lists.osdl.org/pipermail/fastboot/2007-January/thread.html#5774
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Zou, Nanhai <nanhai.zou@intel.com>
Acked-by: Jay Lan <jlan@sgi.com>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit e4f0ae0ea63caceff37a13f281a72652b7ea71ba.
It's not wrong, but it's not right either, and everybody seems to agree
that the right fix is probably to do the ccr3 write after the ccr4 one
(and that we also should clean it up a bit). And after that we need to
really validate that all the bits that we write to ccr4 actually do
work.
The old 2.6.19 code was insane, and basically didn't change ccr4 at all
(even though it certainly looks like it was the *intent* to do so). So
let's revert the change that may fix things, just because it's not what
was actually ever tested when the code was written, even if it _was_ the
intent.
There's a discussion on http://lkml.org/lkml/2007/1/9/63 that was
started by the patch that now gets reverted, and that discussion may
well contain the proper long-term fix.
Suggested-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
a) sun4d_boot_one_cpu() should be __cpuinit (called only from
__cpuinit __cpu_up(), for one thing, leads to calls of __cpuinit
functions for another).
b) got externs in arch/sparc/kernel/smp.c to match reality.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
i386 boot/compressed/relocs checks for absolute symbols and warns about
unexpected ones. If you build with modversions, you get ~2500 warnings
about __crc_<symbol>. These suckers are really absolute symbols - we
do _not_ want to modify them on relocation.
They are generated by genksyms - EXPORT_... generates a weak alias, then
genksyms produces an ld script with __crc_<symbol> = <checksum> and it's
fed to ld to produce the final object file. Their only use is to match
kernel and module at modprobe time; they _must_ be absolute.
boot/compressed/relocs has a whitelist of known absolute symbols, but
it doesn't know about __crc_... stuff. As the result, we get shitloads
of false positives on any ld(1) version.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
... and having it __init is a bad idea.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the same signal frame alignment calculations as the underlying
architecture. x86_64 appeared to do this, but the "- 8" was really
subtracting 8 * sizeof(struct rt_sigframe) rather than 8 bytes.
UML/i386 might have been OK, but I changed the calculation to match
i386 just to be sure.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Antoine Martin <antoine@nagafix.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Remove unneeded errata workaround from p4-clockmod.
[CPUFREQ] check sysfs_create_link return value
|
|
Kconfig recognizes the end of help text by receding indentation depth.
Recent patch had broken HOST_VMSPLIT_... choice in arch/um/Kconfig.i386 -
all alternatives are interpreted as part of help text now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix typo of "CONFIG_MT_SMP".
[MIPS] Ocelot G: Fix a few misspellings of CONFIG_GALILEO_GT64240_ETH
[PATCH] Malta: Fix build if CONFIG_MTD is diabled.
|
|
When the world was a simple and static place setting up irqs was easy.
It sufficed to allocate a linux irq number and a find a free cpu
vector we could receive that linux irq on. In those days it was
a safe assumption that any allocated vector was actually in use
so after one global pass through all of the vectors we would have
none left.
These days things are much more dynamic with interrupt controllers
(in the form of MSI or MSI-X) appearing on plug in cards and linux
irqs appearing and disappearing. As these irqs come and go vectors
are allocated and freed, invalidating the ancient assumption that all
allocated vectors stayed in use forever.
So this patch modifies the vector allocator to walk through every
possible vector before giving up, and to check to see if a vector
is in use before assigning it. With these changes we stop leaking
freed vectors and it becomes possible to allocate and free irq vectors
all day long.
This changed was modeled after the vector allocator on x86_64 where
this limitation has already been removed. In essence we don't update
the static variables that hold the position of the last vector we
allocated until have successfully allocated another vector. This
allows us to detect if we have completed one complete scan through
all of the possible vectors.
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4117/1: S3C2412: Fix writel() usage in selection code
[ARM] 4111/1: Allow VFP to work with thread migration on SMP
[ARM] 4112/1: Only ioremap to supersections if DOMAIN_IO is zero
[ARM] 4106/1: S3C2410: typo fixes in register definitions
[ARM] 4102/1: Allow for PHYS_OFFSET on any valid 2MiB address
[ARM] Fix AMBA serial drivers for non-first serial ports
[ARM] 4100/1: iop3xx: fix cpu mask for iop333
[ARM] Update mach-types
[ARM] Fix show_mem() for discontigmem
[ARM] 4096/1: S3C24XX: change return code form s3c2410_gpio_getcfg()
[ARM] 4095/1: S3C24XX: Fix GPIO set for Bank A
[ARM] 4092/1: i.MX/MX1 CPU Frequency scaling latency definition
[ARM] 4089/1: AT91: GPIO wake IRQ cleanup
[ARM] 4088/1: AT91: Unbalanced IRQ in serial driver suspend/resume
[ARM] 4087/1: AT91: CPU reset for SAM9x processors
[ARM] 4086/1: AT91: Whitespace cleanup
[ARM] 4085/1: AT91: Header fixes.
[ARM] 4084/1: Remove CONFIG_DEBUG_WAITQ
|
|
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Reported by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The S3C2412 DMA selection code has the
arguments to writel() the wrong way around.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This workaround unnecessarily cripples functionality to work
around an errata that doesn't seem possible to hit due to
us using the automatic clock throttling in the p4 mcheck code.
See http://lkml.org/lkml/2006/10/28/148 for complete reasoning
and lack of disconsent.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix sys_pciconfig_iobase bus matching
[POWERPC] PS3: add not complete comment to kconfig
[POWERPC] ps3_free_io_irq: Fix inverted error check
[POWERPC] PS3: Fix uniprocessor kernel build
|
|
A stupid bug has been plaguing the sys_pciconfig_iobase on ppc64. It wasn't
noticed until recently as it seems to not affect G5s but it's been causing
problems running X servers on some other machines recently. The bus number
matching was bogus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Add a comment to the PS3 config option to inform users that the current
implementation is not yet complete.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Mirror the logic in the sun4u handler, we have to update
both registers even when we branch out to window fault
fixup handling.
The way it works is that if we are in etrap processing a
fault already, g4/g5 holds the original fault information.
If we take a window spill fault while doing etrap, then
we put the window spill fault info into g4/g5 and this is
what the top-level fault handler ends up processing first.
Then we retry the originally faulting instruction, and
process the original fault at that time.
This is all necessary because of how constrained the trap
registers are in these code paths. These cases trigger
very rarely, so even if there is some performance implication
it's doesn't happen very often. In fact the rarity is why
it took so long to trigger and find this particular bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Update ATSTK1000 defconfig: Enable macb by default
[AVR32] Export clear_page symbol
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
Fix Maple PATA IRQ assignment.
ahci: use 0x80 as wait stat value instead of 0xff
sata_via: style clean up, no indirect method call in LLD
ahci: fix endianness in spurious interrupt message
libata-sff: Don't call bmdma_stop on non DMA capable controllers
libata: implement ATA_FLAG_IGN_SIMPLEX and use it in sata_uli
ahci: improve and limit spurious interrupt messages, take#3
sata_via: don't diddle with ATA_NIEN in ->freeze
libata: set_mode, Fix the FIXME
libata hpt3xn: Hopefully sort out the DPLL logic versus the vendor code
libata cmd64x: whack into a shape that looks like the documentation
|
|
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This fixes UML on hosts with non-standard VM splits. We had changed the
config variable that controls UML behavior on such hosts, but not
propogated the change everywhere. In particular, the values of STUB_CODE
and STUB_DATA relied on the old variable.
I also reformatted the HOST_VMSPLIT_3G help to make it more standard.
Spotted by uml@flonatel.org.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Blaisorblade <blaisorblade@yahoo.it>
Cc: Pravin <shindepravin@gmail.com>
Cc: <uml@flonatel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch makes x86_64 define arch_vma_name for CONFIG_IA32_EMULATION. This
makes the ia32 vDSO mapping appear in /proc/PID/maps with "[vdso]" for ia32
processes, as it does on native i386.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes core dumps to include the vDSO vma, which is left out now.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes ia32 core dumps on x86_64 to include just one phdr for the
vDSO vma. Currently it writes a confused format with two phdrs for the
address, one without contents and one with. This patch removes the
special-case core writing macros for the ia32 vDSO. Instead, it uses
VM_ALWAYSDUMP in the vma. This changes core dumps so they no longer include
the non-PT_LOAD phdrs from the vDSO, consistent with fixed native i386 core
dumps.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes core dumps to include the vDSO vma, which is left out now.
It removes the special-case core writing macros, which were not doing the
right thing for the vDSO vma anyway. Instead, it uses VM_ALWAYSDUMP in the
vma; there is no need for the fixmap page to be installed. It handles the
CONFIG_COMPAT_VDSO case by making elf_core_dump use the fake vma from
get_gate_vma after real vmas in the same way the /proc/PID/maps code does.
This changes core dumps so they no longer include the non-PT_LOAD phdrs from
the vDSO. I made the change to add them in the first place, but in turned out
that nothing ever wanted them there since the advent of NT_AUXV. It's cleaner
to leave them out, and just let the phdrs inside the vDSO image speak for
themselves.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I wouldn't mind if CONFIG_COMPAT_VDSO went away entirely. But if it's there,
it should work properly. Currently it's quite haphazard: both real vma and
fixmap are mapped, both are put in the two different AT_* slots, sysenter
returns to the vma address rather than the fixmap address, and core dumps yet
are another story.
This patch makes CONFIG_COMPAT_VDSO disable the real vma and use the fixmap
area consistently. This makes it actually compatible with what the old vdso
implementation did.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Enable the Atmel MACB ethernet driver by default on ATSTK1000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
Add missing EXPORT_SYMBOL(clear_page), allowing ext3 to be compiled
as a module.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
|
|
The current lazy saving of the VFP registers is no longer possible
with thread migration on SMP. This patch implements a per-CPU
vfp-state pointer and the saving of the VFP registers at every context
switch. The registers restoring is still performed in a lazy way.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Supersections do not have a field for the domain and it is always
0. This patch prevents the creation of supersections during ioremap
when DOMAIN_IO is not zero (i.e. !defined(CONFIG_IO_36)).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
kspd which due to makefile order happens to be initialized before the
vpe loader causes references to vpecontrol lists before they're actually
been initialized.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
While at it, change message on DEC for consistency.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
