| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Current pxa3xx_nand controller has two chip select which
both be workable. This patch enable this feature.
Update platform driver to support this feature.
Another notice should be taken that:
When you want to use this feature, you should not enable the
keep configuration feature, for two chip select could be
attached with different nand chip. The different page size
and timing requirement make the keep configuration impossible.
Signed-off-by: Lei Wen <leiwen@marvell.com>
|
|
Instead of specifying a callback for dynamic partitioning, use
MTDPART_OFS_RETAIN for reserving a place near the end of flash for
RedBoot.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Currently atmel_nand driver used by AT91 and AVR32 calls a special callback
which return nand partition table and number of partitions. However in all
boards this callback returns just static data. So drop this callback and
make atmel_nand use partition table provided statically via platform_data.
Nicolas Ferre: I am in favor for a mainline inclusion through linux-mtd tree.
Hans-Christian Egtvedt: I'm fine by sending the changes for AVR32 through linux-mtd
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Recall the recently added prefix requirements:
* "NAND_" for flags in nand.h, used in nand_chip.options
* "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
or in nand_bbt_descr.options
Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.
Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
This patch works with the following three flags from two headers (nand.h
and bbm.h):
(1) NAND_USE_FLASH_BBT (nand.h)
(2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
(3) NAND_BBT_NO_OOB (bbm.h)
These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.
This patch accomplishes the following:
* eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
* move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h
It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.
I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-tip
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-tip:
x86-64: Rework vsyscall emulation and add vsyscall= parameter
x86-64: Wire up getcpu syscall
x86: Remove unnecessary compile flag tweaks for vsyscall code
x86-64: Add vsyscall:emulate_vsyscall trace event
x86-64: Add user_64bit_mode paravirt op
x86-64, xen: Enable the vvar mapping
x86-64: Work around gold bug 13023
x86-64: Move the "user" vsyscall segment out of the data segment.
x86-64: Pad vDSO to a page boundary
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
|
git://git.pengutronix.de/git/imx/linux-2.6 into fixes
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Don't do hypervisor calls on non-sun4v in DS driver.
|
|
Reported-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf symbols: Check '/tmp/perf-' symbol file ownership
perf sched: Usage leftover from trace -> script rename
perf sched: Do not delete session object prematurely
perf tools: Check $HOME/.perfconfig ownership
perf, x86: Add model 45 SandyBridge support
perf tools: Add support to install perf python extension
perf tools: do not look at ./config for configuration
perf tools: Make clean leaves some files
perf lock: Dropping unsupported ':r' modifier
perf probe: Fix coredump introduced by probe module option
jump label: Reduce the cycle count by changing the link order
perf report: Use ui__warning in some more places
perf python: Add PERF_RECORD_{LOST,READ,SAMPLE} routine tables
perf evlist: Introduce 'disable' method
trace events: Update version number reference to new 3.x scheme for EVENT_POWER_TRACING_DEPRECATED
perf buildid-cache: Zero out buffer of filenames when adding/removing buildid
|
|
Instead of setting up a match interrupt for 'current_time + delta'
on ->set_next_event(), program timer 0 to count down from 'delta - 1'
and trigger an interrupt when it reaches zero.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Currently, arch-mmp/time.c uses timer 0 both as a clocksource timer
and as a clockevent timer, the latter by setting up a comparator
interrupt to match on 'current_time + delta'. This is problematic
if delta is small enough, as that can lead to 'current_time + delta'
already being in the past when comparator setup has finished, leading
to the requested event not triggering.
As there is also a silicon issue that requires stopping a timer's
counter while writing to one of its match registers, we'll switch to
using two separate timers -- timer 0 as clockevent timer, which we'll
start and stop on every invocation of ->set_next_event(), and timer 1
as clocksource timer, which will be free-running.
This first patch enables timer 1 on boot, so that we can use it as
clocksource timer.
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Move definitions from mfp-gplugd.h to mfp-pxa168.h as they aren't
gplugD specific.
Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
This got added in:
commit ef6c84454f8567d4968c210d7d194fb711ed3739
Author: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Wed Nov 24 11:54:25 2010 +0800
ARM: pxa: add iwmmx support for PJ4
which does:
- mrc p15, 0, r2, c15, c1, 0
- orr r2, r2, #0x3 @ enable access to CP0 and CP1
- mcr p15, 0, r2, c15, c1, 0
+ @ enable access to CP0 and CP1
+ XSC(mrc p15, 0, r2, c15, c1, 0)
+ XSC(orr r2, r2, #0x3)
+ XSC(mcr p15, 0, r2, c15, c1, 0)
but then later does:
- mrc p15, 0, r4, c15, c1, 0
- orr r4, r4, #0x3 @ enable access to CP0 and CP1
- mcr p15, 0, r4, c15, c1, 0
+ @ enable access to CP0 and CP1
+ XSC(mrc p15, 0, r4, c15, c1, 0)
+ XSC(orr r4, r4, #0xf)
+ XSC(mcr p15, 0, r4, c15, c1, 0)
Signed-off-by: Lennert Buytenhek <buytenh@laptop.org>
Acked-by Haojian <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
|
|
There are three choices:
vsyscall=native: Vsyscalls are native code that issues the
corresponding syscalls.
vsyscall=emulate (default): Vsyscalls are emulated by instruction
fault traps, tested in the bad_area path. The actual contents of
the vsyscall page is the same as the vsyscall=native case except
that it's marked NX. This way programs that make assumptions about
what the code in the page does will not be confused when they read
that code.
vsyscall=none: Trying to execute a vsyscall will segfault.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/8449fb3abf89851fd6b2260972666a6f82542284.1312988155.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
getcpu is available as a vdso entry and an emulated vsyscall.
Programs that for some reason don't want to use the vdso should
still be able to call getcpu without relying on the slow emulated
vsyscall. It costs almost nothing to expose it as a real syscall.
We also need this for the following patch in vsyscall=native mode.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/6b19f55bdb06a0c32c2fa6dba9b6f222e1fde999.1312988155.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
As of commit 98d0ac38ca7b1b7a552c9a2359174ff84decb600
Author: Andy Lutomirski <luto@mit.edu>
Date: Thu Jul 14 06:47:22 2011 -0400
x86-64: Move vread_tsc and vread_hpet into the vDSO
user code no longer directly calls into code in arch/x86/kernel/, so
we don't need compile flag hacks to make it safe. All vdso code is
in the vdso directory now.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/835cd05a4c7740544d09723d6ba48f4406f9826c.1312988155.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Really fix build without CONFIG_PCI
powerpc: Fix build without CONFIG_PCI
powerpc/4xx: Fix build of PCI code on 405
powerpc/pseries: Simplify vpa deregistration functions
powerpc/pseries: Cleanup VPA registration and deregistration errors
powerpc/pseries: Fix kexec on recent firmware versions
MAINTAINERS: change maintainership of mpc5xxx
powerpc: Make KVM_GUEST default to n
powerpc/kvm: Fix build errors with older toolchains
powerpc: Lack of ibm,io-events not that important!
powerpc: Move kdump default base address to half RMO size on 64bit
powerpc/perf: Disable pagefaults during callchain stack read
ppc: Remove duplicate definition of PV_POWER7
powerpc: pseries: Fix kexec on machines with more than 4TB of RAM
powerpc: Jump label misalignment causes oops at boot
powerpc: Clean up some panic messages in prom_init
powerpc: Fix device tree claim code
powerpc: Return the_cpu_ spec from identify_cpu
powerpc: mtspr/mtmsr should take an unsigned long
|
|
The PCI nanoengine driver in the SA1100 machine probably has not
been building for some time. It probably dragged hardware.h
in implicitly and now it doesn't anymore. After this an SA1100
build selecting all system variants will build successfully.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Brown paper bag day, previous commit wouldn't work very well with modules
enabled. Move the exports into the ifdef.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If CONFIG_OMAP_32K_TIMER is not selected and dmtimer is used as clocksource, the
timer stops counting once overflow occurs as it was not set in autoreload mode.
This results into timekeeping failure: for example, 'sleep 1' at the shell after
the timer counter overflow would hang.
This patch sets up autoreload when starting the clocksource timer which fixes
the above issue.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Since 7203f8a48bb63015ebe58a6f2a38aec1cb208b9d (arm: mach-omap2: remove
NULL board_mux from board files) NULL board_mux is defined in mux.h.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use kstrdup rather than duplicating its implementation
The semantic patch that makes this output is available
in scripts/coccinelle/api/kstrdup.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The pointer "va" returned from "phys_to_virt(pa)" is never used in
"sgtable_fill_kmalloc()".So,it is safe to remove this set-but-unused variable.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Machine database already updated:
http://www.arm.linux.org.uk/developer/machines/list.php?id=3284
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add missing definitions for the AM3505/3517 UART4 such
as DMAs, INTs and base address.
Signed-of-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into fixes
|
|
This has now been well tested, and several platforms are now selecting
this directly. It's time to drop its experimental status.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Builds for multi-OMAP2 (e.g., OMAP2420 with OMAP2430) with
CONFIG_ARCH_OMAP4=n fail with the following errors:
arch/arm/mach-omap2/built-in.o: In function `_enable_module':
arch/arm/mach-omap2/omap_hwmod.c:701: undefined reference to `omap4_cminst_module_enable'
arch/arm/mach-omap2/built-in.o: In function `_disable_module':
arch/arm/mach-omap2/omap_hwmod.c:726: undefined reference to `omap4_cminst_module_disable'
arch/arm/mach-omap2/built-in.o: In function `_wait_target_disable':
arch/arm/mach-omap2/omap_hwmod.c:1179: undefined reference to `omap4_cminst_wait_module_idle'
This is probably due to the preprocessor directives in
arch/arm/plat-omap/include/plat/cpu.h that convert some cpu_is_omap*()
expressions from preprocessor directives into something that is only
resolvable during runtime, if multiple OMAP2 build targets are
selected.
Thanks to Tony Lindgren <tony@atomide.com> for reporting.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit b22f954 (OMAP4: Move common twl6030 configuration to twl-common)
caused compile failures for code for OMAP arch which is not selected by
the config.
Fixes issues like:
With CONFIG_ARCH_OMAP3=y and CONFIG_ARCH_OMAP4=n, I'm getting this:
arch/arm/mach-omap2/built-in.o:(.data+0xf99c): undefined reference to `omap4430_phy_init'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a0): undefined reference to `omap4430_phy_exit'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a4): undefined reference to `omap4430_phy_power'
arch/arm/mach-omap2/built-in.o:(.data+0xf9a8): undefined reference to `omap4430_phy_set_clk'
arch/arm/mach-omap2/built-in.o:(.data+0xf9ac): undefined reference to `omap4430_phy_suspend'
Fix the problem by moving the code to ifdef sections for omap3 and omap4.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support to Romely-EP SandyBridge.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Anhua Xu <anhua.xu@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1312264895-2010-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
With the UM_SIGNAL alignment fault mode, no siginfo structure is
passed to userspace.
POSIX specifies how siginfo_t should be populated for alignment
faults, so this patch does just that:
* si_signo = SIGBUS
* si_code = BUS_ADRALN
* si_addr = misaligned data address at which access was attempted
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
access model
Currently, it's possible to set the kernel to ignore alignment
faults when changing the alignment fault handling mode at runtime
via /proc/sys/alignment, even though this is undesirable on ARMv6
and above, where it can result in infinite spins where an un-fixed-
up instruction repeatedly faults.
In addition, the kernel clobbers any alignment mode specified on
the command-line if running on ARMv6 or above.
This patch factors out the necessary safety check into a couple of
new helper functions, and checks and modifies the fault handling
mode as appropriate on boot and on writes to /proc/cpu/alignment.
Prior to ARMv6, the behaviour is unchanged.
For ARMv6 and above, the behaviour changes as follows:
* Attempting to ignore faults on ARMv6 results in the mode being
forced to UM_FIXUP instead. A warning is printed if this
happened as a result of a write to /proc/cpu/alignment. The
user's UM_WARN bit (if present) is still honoured.
* An alignment= argument from the kernel command-line is now
honoured, except that the kernel will modify the specified mode
as described above. This is allows modes such as UM_SIGNAL and
UM_WARN to be active immediately from boot, which is useful for
debugging purposes.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
poison_init_mem() used a loop of:
while ((count = count - 4))
which has 2 problems - an off by one error so that we do one less word
than we should, and the other is that if count == 0 then we loop forever
and poison too much. On a platform with HAVE_TCM=y but nothing in the
TCM's, this caused corruption and the platform failed to boot.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The file mm/proc-arm946.S contains a typo and is missing a structure
member in __arm946_proc_info. The former prevents compilation
and the latter causes problems during boot. It is likely this
file was manually copied from a similar file and not tested, then
later updates to the *_proc_info structures missed this file.
This patch will apply (with offset) with or without the
recent macro unification work that has been done in this directory.
This was verified against linux-next/stable last week.
See arm-linux-kernel thread:
http://lists.arm.linux.org.uk/lurker/message/20110718.103237.0106d468.en.html
Signed-off-by: Brian S. Julin <bri@abrij.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit fad107086d5a869c1c07e5bb35b7b57a10ecf578 fixed the wrong test for MX51
as the MX51 addresses are wrong for MX50 and MX53 but now it's MX51 only,
UART_PADDR is not defined anymore when building for MX50/MX53.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Steev Klimaszewski <steev@genesi-usa.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
irq_to_gpio() is being called on a GPIO so change to using
gpio_to_irq() instead.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
|
|
For marketing reasons the part will be called WM8996. In order to avoid
user confusion rename the driver to reflect this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Fix build with DEBUG_PAGEALLOC enabled.
|
|
The generic library code already exports the generic function, this was
left-over from the ARM-specific version that just got removed.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 1eb19a12bd22 ("lib/sha1: use the git implementation of
SHA-1"), the ARM SHA1 routines no longer work. The reason? They
depended on the larger 320-byte workspace, and now the sha1 workspace is
just 16 words (64 bytes). So the assembly version would overwrite the
stack randomly.
The optimized asm version is also probably slower than the new improved
C version, so there's no reason to keep it around. At least that was
the case in git, where what appears to be the same assembly language
version was removed two years ago because the optimized C BLK_SHA1 code
was faster.
Reported-and-tested-by: Joachim Eastwood <manabian@gmail.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/trace: Fix compile error when CONFIG_XEN_PRIVILEGED_GUEST is not set
xen: Fix misleading WARN message at xen_release_chunk
xen: Fix printk() format in xen/setup.c
xen/tracing: it looks like we wanted CONFIG_FTRACE
xen/self-balloon: Add dependency on tmem.
xen/balloon: Fix compile errors - missing header files.
xen/grant: Fix compile warning.
xen/pciback: remove duplicated #include
|
|
arch/sparc/mm/init_64.c:1622:22: error: unused variable '__swapper_4m_tsb_phys_patch_end' [-Werror=unused-variable]
arch/sparc/mm/init_64.c:1621:22: error: unused variable '__swapper_4m_tsb_phys_patch' [-Werror=unused-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
