| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Delete the 10 msec delay between the INIT and SIPI when starting
slave cpus. I can find no requirement for this delay. BIOS also
has similar code sequences without the delay.
Removing the delay reduces boot time by 40 sec. Every bit helps.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20110805140900.GA6774@sgi.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When executing EC commands, only waiting when there are still
more bytes to write is usually fine. However, if the system
suspends very quickly after a call to olpc_ec_cmd(), the last
data byte may not yet be transferred to the EC, and the command
will not complete.
This solves a bug where the SCI wakeup mask was not correctly
written when going into suspend.
It means that sometimes, on XO-1.5 (but not XO-1), the
devices that were marked as wakeup sources can't wake up
the system. e.g. you ask for wifi wakeups, suspend, but then
incoming wifi frames don't wake up the system as they should.
Signed-off-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
omap_sr_disable_reset_volt is called with irqs off in omapx_enter_sleep,
as part of idle sequence, this eventually calls sr_disable and
pm_runtime_put_sync. pm_runtime_put_sync calls rpm_idle, which will
enable interrupts in order to call the callback. In this short interval
when interrupts are enabled, scenarios such as the following can occur:
while interrupts are enabled, the timer interrupt that is supposed to
wake the device out of idle occurs and is acked, so when the CPU finally
goes to off, the timer is already gone, missing a wakeup event.
Further, as the documentation for runtime states:"
However, subsystems can use the pm_runtime_irq_safe() helper function
to tell the PM core that a device's ->runtime_suspend() and ->runtime_resume()
callbacks should be invoked in atomic context with interrupts disabled
(->runtime_idle() is still invoked the default way)."
Hence, replace pm_runtime_put_sync with pm_runtime_put_sync_suspend
to invoke the suspend handler and shut off the fclk for SmartReflex
module instead of using the idle handler in interrupt disabled context.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Colin Cross <ccross@google.com>
[khilman@ti.com: minor Subject edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Board code should not touch omap_device internals. To get the MPU/IVA devices,
use existing APIs: omap2_get_mpu_device(), omap2_get_iva_device().
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
OMAP1 needs this also since GPIO driver (common for all OMAPs) is
being converted to use generic IRQ chip.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
SmartReflex should be disabled while entering low power mode due to
a) SmartReflex values are not defined for retention voltage, further
b) with SmartReflex enabled, if CPU enters lower c-states, FSM will try
to bump the voltage to current OPP's voltage for which it has entered c-state;
hence SmartReflex needs to be disabled for MPU, CORE and IVA voltage
domains in idle path before enabling auto retention voltage achievement
on the device.
However, since the current pm_runtime setup for SmartReflex devices are
setup to allow callbacks to be invoked with interrupts enabled, calling
SmartReflex enable/disable from other contexts such as idle paths
where preemption is disabled causes warnings such as the following
indicating of a potential race.
[ 82.023895] [<c04d079c>] (__irq_svc+0x3c/0x120) from [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c)
[ 82.023895] [<c04d0484>] (_raw_spin_unlock_irq+0x28/0x2c) from [<c0323234>] (rpm_callback+0x4c/0x68)
[ 82.023956] [<c0323234>] (rpm_callback+0x4c/0x68) from [<c0323f7c>] (rpm_resume+0x338/0x53c)
[ 82.023956] [<c0323f7c>] (rpm_resume+0x338/0x53c) from [<c03243f4>] (__pm_runtime_resume+0x48/0x60)
[ 82.023986] [<c03243f4>] (__pm_runtime_resume+0x48/0x60) from [<c008aee0>] (sr_enable+0xa8/0x19c)
[ 82.023986] [<c008aee0>] (sr_enable+0xa8/0x19c) from [<c008b2fc>] (omap_sr_enable+0x50/0x90)
[ 82.024017] [<c008b2fc>] (omap_sr_enable+0x50/0x90) from [<c00888c0>] (omap4_enter_sleep+0x138/0x168)
Instead, we use pm_runtime_irq_safe to tell the PM core that callbacks can be
invoked in interrupt disabled contexts.
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
CONFIG_PM is no longer a user-selectable Kconfig option. Rather it is
automatically enabled if either CONFIG_SUSPEND or CONFIG_RUNTIME_PM is
enabled, so having a 'select PM' here is redunant when 'select
CONFIG_PM_RUNTIME' is present.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Size mondo queues more sanely.
sparc: Access kernel TSB using physical addressing when possible.
sparc: Fix __atomic_add_unless() return value.
sparc: use kbuild-generic support for true asm-generic header files
sparc: Use popc when possible for ffs/__ffs/ffz.
sparc: Set reboot-cmd using reboot data hypervisor call if available.
sparc: Add some missing hypervisor API groups.
sparc: Use hweight64() in popc emulation.
sparc: Use popc if possible for hweight routines.
sparc: Minor tweaks to Niagara page copy/clear.
sparc: Sanitize cpu feature detection and reporting.
|
|
If the DPLL is already enabled, don't try to enable it again.
Since write to the DPLL control register will make the DPLL
reset and which will cause some issues when some child module
are sourced from this DPLL.
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
with CONFIG_XEN and CONFIG_FTRACE set we get this:
arch/x86/xen/trace.c:22: error: ‘__HYPERVISOR_console_io’ undeclared here (not in a function)
arch/x86/xen/trace.c:22: error: array index in initializer not of integer type
arch/x86/xen/trace.c:22: error: (near initialization for ‘xen_hypercall_names’)
arch/x86/xen/trace.c:23: error: ‘__HYPERVISOR_physdev_op_compat’ undeclared here (not in a function)
Issue was that the definitions of __HYPERVISOR were not pulled
if CONFIG_XEN_PRIVILEGED_GUEST was not set.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
There is currently no upper limit on the mondo queue sizes we'll use,
which guarentees that we'll eventually his page allocation limits, and
thus allocation failures, due to MAX_ORDER.
Cap the sizes sanely, current limits are:
CPU MONDO 2 * max_possible_cpus
DEV MONDO 256 (basically NR_IRQS)
RES MONDO 128
NRES MONDO 4
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On sun4v this is basically required since we point the hypervisor and
the TSB walking hardware at these tables using physical addressing
too.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit fea80311a939a746533a6d7e7c3183729d6a3faf
"iomap: make IOPORT/PCI mapping functions conditional"
Broke powerpc build without CONFIG_PCI as we would still define
pci_iomap(), which overlaps with the new empty inline in the headers.
Make our implementation conditional on CONFIG_PCI
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 112d1fe9f7715db423ffeec5ac1beccff6093dc4
"powerpc/4xx: Add check_link to struct ppc4xx_pciex_hwops" inadvertently
broke 405 builds due to some functions being over protected by an
ifdef CONFIG_44x.
Move them back out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The VPA, SLB shadow and DTL degistration functions do not need an
address, so simplify things and remove it.
Also cleanup pseries_kexec_cpu_down a bit by storing the cpu IDs
in local variables.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Make the VPA, SLB shadow and DTL registration and deregistration
functions print consistent messages on error. I needed the firmware
error code while chasing a kexec bug but we weren't printing it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Recent versions of firmware will fail to unmap the virtual processor
area if we have a dispatch trace log registered. This causes kexec
to fail.
If a trace log is registered this patch unregisters it before the
SLB shadow and virtual processor areas, fixing the problem.
The address argument is ignored by firmware on unregister so we
may as well remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
KVM_GUEST adds a 1 MB array to the kernel (kvm_tmp) which grew
my kernel enough to cause it to fail to boot.
Dynamically allocating or reducing the size of this array is a
good idea, but in the meantime I think it makes sense to make
KVM_GUEST default to n in order to minimise surprises.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On a box with gcc 4.3.2, I see errors like:
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1254: Error: Unrecognized opcode: stxvd2x
arch/powerpc/kvm/book3s_hv_rmhandlers.S:1316: Error: Unrecognized opcode: lxvd2x
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The ibm,io-events code is a bit verbose with its error messages.
Reverse the reporting so we only print when we successfully enable
I/O event interrupts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We are seeing boot failures on some very large boxes even with
commit b5416ca9f824 (powerpc: Move kdump default base address to
64MB on 64bit).
This patch halves the RMO so both kernels get about the same
amount of RMO memory. On large machines this region will be
at least 256MB, so each kernel will get 128MB.
We cap it at 256MB (small SLB size) since some early allocations need
to be in the bolted SLB region. We could relax this on machines with
1TB SLBs in a future patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Panic observed on an older kernel when collecting call chains for
the context-switch software event:
[<b0180e00>]rb_erase+0x1b4/0x3e8
[<b00430f4>]__dequeue_entity+0x50/0xe8
[<b0043304>]set_next_entity+0x178/0x1bc
[<b0043440>]pick_next_task_fair+0xb0/0x118
[<b02ada80>]schedule+0x500/0x614
[<b02afaa8>]rwsem_down_failed_common+0xf0/0x264
[<b02afca0>]rwsem_down_read_failed+0x34/0x54
[<b02aed4c>]down_read+0x3c/0x54
[<b0023b58>]do_page_fault+0x114/0x5e8
[<b001e350>]handle_page_fault+0xc/0x80
[<b0022dec>]perf_callchain+0x224/0x31c
[<b009ba70>]perf_prepare_sample+0x240/0x2fc
[<b009d760>]__perf_event_overflow+0x280/0x398
[<b009d914>]perf_swevent_overflow+0x9c/0x10c
[<b009db54>]perf_swevent_ctx_event+0x1d0/0x230
[<b009dc38>]do_perf_sw_event+0x84/0xe4
[<b009dde8>]perf_sw_event_context_switch+0x150/0x1b4
[<b009de90>]perf_event_task_sched_out+0x44/0x2d4
[<b02ad840>]schedule+0x2c0/0x614
[<b0047dc0>]__cond_resched+0x34/0x90
[<b02adcc8>]_cond_resched+0x4c/0x68
[<b00bccf8>]move_page_tables+0xb0/0x418
[<b00d7ee0>]setup_arg_pages+0x184/0x2a0
[<b0110914>]load_elf_binary+0x394/0x1208
[<b00d6e28>]search_binary_handler+0xe0/0x2c4
[<b00d834c>]do_execve+0x1bc/0x268
[<b0015394>]sys_execve+0x84/0xc8
[<b001df10>]ret_from_syscall+0x0/0x3c
A page fault occurred walking the callchain while creating a perf
sample for the context-switch event. To handle the page fault the
mmap_sem is needed, but it is currently held by setup_arg_pages.
(setup_arg_pages calls shift_arg_pages with the mmap_sem held.
shift_arg_pages then calls move_page_tables which has a cond_resched
at the top of its for loop - hitting that cond_resched is what caused
the context switch.)
This is an extension of Anton's proposed patch:
https://lkml.org/lkml/2011/7/24/151
adding case for 32-bit ppc.
Tested on the system that first generated the panic and then again
with latest kernel using a PPC VM. I am not able to test the 64-bit
path - I do not have H/W for it and 64-bit PPC VMs (qemu on Intel)
is horribly slow.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
One definition of PV_POWER7 seems enough to me.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On a box with 8TB of RAM the MMU hashtable is 64GB in size. That
means we have 4G PTEs. pSeries_lpar_hptab_clear was using a signed
int to store the index which will overflow at 2G.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I hit an oops at boot on the first instruction of timer_cpu_notify:
NIP [c000000000722f88] .timer_cpu_notify+0x0/0x388
The code should look like:
c000000000722f78: eb e9 00 30 ld r31,48(r9)
c000000000722f7c: 2f bf 00 00 cmpdi cr7,r31,0
c000000000722f80: 40 9e ff 44 bne+ cr7,c000000000722ec4
c000000000722f84: 4b ff ff 74 b c000000000722ef8
c000000000722f88 <.timer_cpu_notify>:
c000000000722f88: 7c 08 02 a6 mflr r0
c000000000722f8c: 2f a4 00 07 cmpdi cr7,r4,7
c000000000722f90: fb c1 ff f0 std r30,-16(r1)
c000000000722f94: fb 61 ff d8 std r27,-40(r1)
But the oops output shows:
eb61ffd8 eb81ffe0 eba1ffe8 ebc1fff0 7c0803a6 ebe1fff8 4e800020
00000000 ebe90030 c0000000 00ad0a28 00000000 2fa40007 fbc1fff0 fb61ffd8
So we scribbled over our instructions with c000000000ad0a28, which
is an address inside the jump_table ELF section.
It turns out the jump_table section is only aligned to 8 bytes but
we are aligning our entries within the section to 16 bytes. This
means our entries are offset from the table:
c000000000acd4a8 <__start___jump_table>:
...
c000000000ad0a10: c0 00 00 00 lfs f0,0(0)
c000000000ad0a14: 00 70 cd 5c .long 0x70cd5c
c000000000ad0a18: c0 00 00 00 lfs f0,0(0)
c000000000ad0a1c: 00 70 cd 90 .long 0x70cd90
c000000000ad0a20: c0 00 00 00 lfs f0,0(0)
c000000000ad0a24: 00 ac a4 20 .long 0xaca420
And the jump table sort code gets very confused and writes into the
wrong spot. Remove the alignment, and also remove the padding since
we it saves some space and we shouldn't need it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add a newline to the panic messages in make_room. Also fix a
comment that suggested our chunk size is 4Mb. It's 1MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
I have a box that fails in OF during boot with:
DEFAULT CATCH!, exception-handler=fff00400
at %SRR0: 49424d2c4c6f6768 %SRR1: 800000004000b002
ie "IBM,Logh". OF got corrupted with a device tree string.
Looking at make_room and alloc_up, we claim the first chunk (1 MB)
but we never claim any more. mem_end is always set to alloc_top
which is the top of our available address space, guaranteeing we will
never call alloc_up and claim more memory.
Also alloc_up wasn't setting alloc_bottom to the bottom of the
available address space.
This doesn't help the box to boot, but we at least fail with
an obvious error. We could relocate the device tree in a future
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit af9eef3c7b1ed004c378c89b87642f4937337d50 caused cpu_setup to see
the_cpu_spec, rather than the source struct. However, on 32-bit, the
return value of identify_cpu was being used for feature fixups, and
identify_cpu was returning the source struct. So if cpu_setup patches
the feature bits, the update won't affect the fixups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Add a cast in case the caller passes in a different type, as it would
if mtspr/mtmsr were functions.
Previously, if a 64-bit type was passed in on 32-bit, GCC would bind the
constraint to a pair of registers, and would substitute the first register
in the pair in the asm code. This corresponds to the upper half of the
64-bit register, which is generally not the desired behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'fixefi' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
efi: Fix argument types for SetVariable() for ia64
|
|
Commit a0bfa1373859e9d11dc92561a8667588803e42d8 mispells
cpuidle_idle_call() on ARM and SH code. Fix this to be consistent.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: x86@kernel.org
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: David Brown <davidb@codeaurora.org>
[ Also done by Mark Brown - th ebug has been around forever, and was
noticed in -next, but the idle tree never picked it up. Bad bad bad ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Vsyscall emulation is slow, so make it easy to track down.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/cdaad7da946a80b200df16647c1700db3e1171e9.1312378163.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Three places in the kernel assume that the only long mode CPL 3
selector is __USER_CS. This is not true on Xen -- Xen's sysretq
changes cs to the magic value 0xe033.
Two of the places are corner cases, but as of "x86-64: Improve
vsyscall emulation CS and RIP handling"
(c9712944b2a12373cb6ff8059afcfb7e826a6c54), vsyscalls will segfault
if called with Xen's extra CS selector. This causes a panic when
older init builds die.
It seems impossible to make Xen use __USER_CS reliably without
taking a performance hit on every system call, so this fixes the
tests instead with a new paravirt op. It's a little ugly because
ptrace.h can't include paravirt.h.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/f4fcb3947340d9e96ce1054a432f183f9da9db83.1312378163.git.luto@mit.edu
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Xen needs to handle VVAR_PAGE, introduced in git commit:
9fd67b4ed0714ab718f1f9bd14c344af336a6df7
x86-64: Give vvars their own page
Otherwise we die during bootup with a message like:
(XEN) mm.c:940:d10 Error getting mfn 1888 (pfn 1e3e48) from L1 entry
8000000001888465 for l1e_owner=10, pg_owner=10
(XEN) mm.c:5049:d10 ptwr_emulate: could not get_page_from_l1e()
[ 0.000000] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 0.000000] IP: [<ffffffff8103a930>] xen_set_pte+0x20/0xe0
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/4659478ed2f3480938f96491c2ecbe2b2e113a23.1312378163.git.luto@mit.edu
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Gold has trouble assigning numbers to the location counter inside of
an output section description. The bug was triggered by
9fd67b4ed0714ab718f1f9bd14c344af336a6df7, which consolidated all of
the vsyscall sections into a single section. The workaround is IMO
still nicer than the old way of doing it.
This produces an apparently valid kernel image and passes my vdso
tests on both GNU ld version 2.21.51.0.6-2.fc15 20110118 and GNU
gold (version 2.21.51.0.6-2.fc15 20110118) 1.10 as distributed by
Fedora 15.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/0b260cb806f1f9a25c00ce8377a5f035d57f557a.1312378163.git.luto@mit.edu
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The kernel's loader doesn't seem to care, but gold complains.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/f0716870c297242a841b949953d80c0d87bf3d3f.1312378163.git.luto@mit.edu
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
This avoids an information leak to userspace.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/a63380a3c58a0506a2f5a18ba1b12dbde1f25e58.1312378163.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
|
|
The spec says this takes uint32 for attributes, not uintn.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
WARN message should not complain
"Failed to release memory %lx-%lx err=%d\n"
^^^^^^^
about range when it fails to release just one page,
instead it should say what pfn is not freed.
In addition line:
printk(KERN_INFO "xen_release_chunk: looking at area pfn %lx-%lx: "
...
printk(KERN_CONT "%lu pages freed\n", len);
will be broken if WARN in between this line is fired. So fix it
by using a single printk for this.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Use correct format specifier for unsigned long.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
Apparently we wanted CONFIG_FTRACE rather the CONFIG_FUNCTION_TRACER.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] wire up sendmmsg syscall
[PARISC] fix return type of __atomic64_add_return
[PARISC] Fix futex support
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] signal: use set_restore_sigmask() helper
[S390] smp: remove pointless comments in startup_secondary()
[S390] qdio: Use kstrtoul_from_user
[S390] sclp_async: Use kstrtoul_from_user
[S390] exec: remove redundant set_fs(USER_DS)
[S390] cpu hotplug: on cpu start wait until being marked active
[S390] signal: convert to use set_current_blocked()
[S390] asm offsets: fix coding style
[S390] Add support for IBM zEnterprise 114
[S390] dasd: check if raw track access is supported
[S390] Use diagnose 308 for system reset
[S390] Export store_status() function
[S390] dasd: use vmalloc for statistics input buffer
[S390] Add PSW restart shutdown trigger
[S390] missing return in page_table_alloc_pgste
[S390] qdio: 2nd stage retry on SIGA-W busy conditions
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry Kasatkin reports:
"kernel-devel package with kernel headers have no <include/xen>
directory if XEN is disabled. Modules which inclide asm/io.h won't
compile.
XEN related content is behind the CONFIG_XEN flag in the io.h. And
<xen/xen.h> should be also behind CONFIG_XEN flag."
So move the include of <xen/xen.h> down into the section that is
conditional on CONFIG_XEN.
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
cpuidle: stop depending on pm_idle
x86 idle: move mwait_idle_with_hints() to where it is used
cpuidle: replace xen access to x86 pm_idle and default_idle
cpuidle: create bootparam "cpuidle.off=1"
mrst_pmu: driver for Intel Moorestown Power Management Unit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'apei-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI, APEI, EINJ Param support is disabled by default
APEI GHES: 32-bit buildfix
ACPI: APEI build fix
ACPI, APEI, GHES: Add hardware memory error recovery support
HWPoison: add memory_failure_queue()
ACPI, APEI, GHES, Error records content based throttle
ACPI, APEI, GHES, printk support for recoverable error via NMI
lib, Make gen_pool memory allocator lockless
lib, Add lock-less NULL terminated single list
Add Kconfig option ARCH_HAVE_NMI_SAFE_CMPXCHG
ACPI, APEI, Add WHEA _OSC support
ACPI, APEI, Add APEI bit support in generic _OSC call
ACPI, APEI, GHES, Support disable GHES at boot time
ACPI, APEI, GHES, Prevent GHES to be built as module
ACPI, APEI, Use apei_exec_run_optional in APEI EINJ and ERST
ACPI, APEI, Add apei_exec_run_optional
ACPI, APEI, GHES, Do not ratelimit fatal error printk before panic
ACPI, APEI, ERST, Fix erst-dbg long record reading issue
ACPI, APEI, ERST, Prevent erst_dbg from loading if ERST is disabled
|
|
Unfortunately, the module fixups cause the kernel to fail to build
when SMP is not enabled. Fix this by removing the reference to
fixup_smp on non-SMP fixup kernels, but ensuring that if we do have
the SMP fixup section, we refuse to load the module.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
