| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit da6fa7ef67f07108a1b0cb9fd9e7fcaabd39c051 ]
Recent AMD systems support using MWAIT for C1 state. However, MWAIT will
not allow deeper cstates than C1 on current systems.
play_dead() expects to use the deepest state available. The deepest state
available on AMD systems is reached through SystemIO or HALT. If MWAIT is
available, it is preferred over the other methods, so the CPU never reaches
the deepest possible state.
Don't try to use MWAIT to play_dead() on AMD systems. Instead, use CPUIDLE
to enter the deepest state advertised by firmware. If CPUIDLE is not
available then fallback to HALT.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
Link: https://lkml.kernel.org/r/20180403140228.58540-1-Yazen.Ghannam@amd.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit d3878e164dcd3925a237a20e879432400e369172 ]
The TSC calibration code uses HPET as reference. The conversion normalizes
the delta of two HPET timestamps:
hpetref = ((tshpet1 - tshpet2) * HPET_PERIOD) / 1e6
and then divides the normalized delta of the corresponding TSC timestamps
by the result to calulate the TSC frequency.
tscfreq = ((tstsc1 - tstsc2 ) * 1e6) / hpetref
This uses do_div() which takes an u32 as the divisor, which worked so far
because the HPET frequency was low enough that 'hpetref' never exceeded
32bit.
On Skylake machines the HPET frequency increased so 'hpetref' can exceed
32bit. do_div() truncates the divisor, which causes the calibration to
fail.
Use div64_u64() to avoid the problem.
[ tglx: Fixes whitespace mangled patch and rewrote changelog ]
Signed-off-by: Xiaoming Gao <newtongao@tencent.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: peterz@infradead.org
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/38894564-4fc9-b8ec-353f-de702839e44e@gmail.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit a24cd490739586a7d2da3549a1844e1d7c4f4fc4 ]
hypfs_fill_super() might fail to allocate sbi; hypfs_kill_super()
should not oops on that.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 13a83eac373c49c0a081cbcd137e79210fe78acd ]
On boot we save the configuration space of PCIe bridges. We do this so
when we get an EEH event and everything gets reset that we can restore
them.
Unfortunately we save this state before we've enabled the MMIO space
on the bridges. Hence if we have to reset the bridge when we come back
MMIO is not enabled and we end up taking an PE freeze when the driver
starts accessing again.
This patch forces the memory/MMIO and bus mastering on when restoring
bridges on EEH. Ideally we'd do this correctly by saving the
configuration space writes later, but that will have to come later in
a larger EEH rewrite. For now we have this simple fix.
The original bug can be triggered on a boston machine by doing:
echo 0x8000000000000000 > /sys/kernel/debug/powerpc/PCI0001/err_injct_outbound
On boston, this PHB has a PCIe switch on it. Without this patch,
you'll see two EEH events, 1 expected and 1 the failure we are fixing
here. The second EEH event causes the anything under the PHB to
disappear (i.e. the i40e eth).
With this patch, only 1 EEH event occurs and devices properly recover.
Fixes: 652defed4875 ("powerpc/eeh: Check PCIe link after reset")
Cc: stable@vger.kernel.org # v3.11+
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c96eebf07692e53bf4dd5987510d8b550e793598 ]
The label .Llast_fixup\@ is jumped to on page fault within the final
byte set loop of memset (on < MIPSR6 architectures). For some reason, in
this fault handler, the v1 register is randomly set to a2 & STORMASK.
This clobbers v1 for the calling function. This can be observed with the
following test code:
static int __init __attribute__((optimize("O0"))) test_clear_user(void)
{
register int t asm("v1");
char *test;
int j, k;
pr_info("\n\n\nTesting clear_user\n");
test = vmalloc(PAGE_SIZE);
for (j = 256; j < 512; j++) {
t = 0xa5a5a5a5;
if ((k = clear_user(test + PAGE_SIZE - 256, j)) != j - 256) {
pr_err("clear_user (%px %d) returned %d\n", test + PAGE_SIZE - 256, j, k);
}
if (t != 0xa5a5a5a5) {
pr_err("v1 was clobbered to 0x%x!\n", t);
}
}
return 0;
}
late_initcall(test_clear_user);
Which demonstrates that v1 is indeed clobbered (MIPS64):
Testing clear_user
v1 was clobbered to 0x1!
v1 was clobbered to 0x2!
v1 was clobbered to 0x3!
v1 was clobbered to 0x4!
v1 was clobbered to 0x5!
v1 was clobbered to 0x6!
v1 was clobbered to 0x7!
Since the number of bytes that could not be set is already contained in
a2, the andi placing a value in v1 is not necessary and actively
harmful in clobbering v1.
Reported-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19109/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit daf70d89f80c6e1772233da9e020114b1254e7e0 ]
The __clear_user function is defined to return the number of bytes that
could not be cleared. From the underlying memset / bzero implementation
this means setting register a2 to that number on return. Currently if a
page fault is triggered within the memset_partial block, the value
loaded into a2 on return is meaningless.
The label .Lpartial_fixup\@ is jumped to on page fault. In order to work
out how many bytes failed to copy, the exception handler should find how
many bytes left in the partial block (andi a2, STORMASK), add that to
the partial block end address (a2), and subtract the faulting address to
get the remainder. Currently it incorrectly subtracts the partial block
start address (t1), which has additionally been clobbered to generate a
jump target in memset_partial. Fix this by adding the block end address
instead.
This issue was found with the following test code:
int j, k;
for (j = 0; j < 512; j++) {
if ((k = clear_user(NULL, j)) != j) {
pr_err("clear_user (NULL %d) returned %d\n", j, k);
}
}
Which now passes on Creator Ci40 (MIPS32) and Cavium Octeon II (MIPS64).
Suggested-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/19108/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 8a8158c85e1e774a44fbe81106fa41138580dfd1 ]
The MIPS kernel memset / bzero implementation includes a small_memset
branch which is used when the region to be set is smaller than a long (4
bytes on 32bit, 8 bytes on 64bit). The current small_memset
implementation uses a simple store byte loop to write the destination.
There are 2 issues with this implementation:
1. When EVA mode is active, user and kernel address spaces may overlap.
Currently the use of the sb instruction means kernel mode addressing is
always used and an intended write to userspace may actually overwrite
some critical kernel data.
2. If the write triggers a page fault, for example by calling
__clear_user(NULL, 2), instead of gracefully handling the fault, an OOPS
is triggered.
Fix these issues by replacing the sb instruction with the EX() macro,
which will emit EVA compatible instuctions as required. Additionally
implement a fault fixup for small_memset which sets a2 to the number of
bytes that could not be cleared (as defined by __clear_user).
Reported-by: Chuanhua Lei <chuanhua.lei@intel.com>
Signed-off-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/18975/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 4d1a535b8ec5e74b42dfd9dc809142653b2597f6 ]
glibc 2.26 removed the 'struct ucontext' to "improve" POSIX compliance
and break programs, including User Mode Linux. Fix User Mode Linux
by using POSIX ucontext_t.
This fixes:
arch/um/os-Linux/signal.c: In function 'hard_handler':
arch/um/os-Linux/signal.c:163:22: error: dereferencing pointer to incomplete type 'struct ucontext'
mcontext_t *mc = &uc->uc_mcontext;
arch/x86/um/stub_segv.c: In function 'stub_segv_handler':
arch/x86/um/stub_segv.c:16:13: error: dereferencing pointer to incomplete type 'struct ucontext'
&uc->uc_mcontext);
Cc: stable@vger.kernel.org
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 3b8070335f751aac9f1526ae2e012e6f5b8b0f21 ]
The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or
OPAL_BUSY_EVENT from firmware, which causes large scheduling
latencies, and various lockup errors to trigger (again, BMC reboot
can cause it).
Fix this by converting it to the standard form OPAL_BUSY loop that
sleeps.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Depends-on: 34dd25de9fe3 ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 34dd25de9fe3f60bfdb31b473bf04b28262d0896 ]
This is the start of an effort to tidy up and standardise all the
delays. Existing loops have a range of delay/sleep periods from 1ms
to 20ms, and some have no delay. They all loop forever except rtc,
which times out after 10 retries, and that uses 10ms delays. So use
10ms as our standard delay. The OPAL maintainer agrees 10ms is a
reasonable starting point.
The idea is to use the same recipe everywhere, once this is proven to
work then it will be documented as an OPAL API standard. Then both
firmware and OS can agree, and if a particular call needs something
else, then that can be documented with reasoning.
This is not the end-all of this effort, it's just a relatively easy
change that fixes some existing high latency delays. There should be
provision for standardising timeouts and/or interruptible loops where
possible, so non-fatal firmware errors don't cause hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 0bfdf598900fd62869659f360d3387ed80eb71cf ]
asm/barrier.h is not always included after asm/synch.h, which meant
it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would
be eieio when it should be lwsync. kernel/time/hrtimer.c is one case.
__SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in
to where it's used. Previously with my small simulator config, 377
instances of eieio in the tree. After this patch there are 55.
Fixes: 46d075be585e ("powerpc: Optimise smp_wmb")
Cc: stable@vger.kernel.org # v2.6.29+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 741de617661794246f84a21a02fc5e327bffc9ad ]
opal_nvram_write currently just assumes success if it encounters an
error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO
on other errors instead.
Fixes: 628daa8d5abf ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks")
Cc: stable@vger.kernel.org # v3.2+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e8fd0adf105e132fd84545997bbef3d5edc2c9c1 ]
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 15deb080a6087b73089139569558965750e69d67 ]
When loadparm is set in reipl parm block, the kernel should also set
DIAG308_FLAGS_LP_VALID flag.
This fixes loadparm ignoring during z/VM fcp -> ccw reipl and kvm direct
boot -> ccw reipl.
Cc: <stable@vger.kernel.org>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 615b2665fd20c327b631ff1e79426775de748094 ]
As found by the ubsan checker, the value of the 'index' variable can be
out of range for the bc[] array:
UBSAN: Undefined behaviour in arch/parisc/kernel/drivers.c:655:21
index 6 is out of range for type 'char [6]'
Backtrace:
[<104fa850>] __ubsan_handle_out_of_bounds+0x68/0x80
[<1019d83c>] check_parent+0xc0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019d86c>] check_parent+0xf0/0x170
[<1019d91c>] descend_children+0x30/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019d938>] descend_children+0x4c/0x6c
[<1059e164>] device_for_each_child+0x60/0x98
[<1019cd54>] parse_tree_node+0x40/0x54
[<1019cffc>] hwpath_to_device+0xa4/0xc4
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 6c95483b768c62f8ee933ae08a1bdbcb78b5410f ]
Orabug: 20902628
When an ldc control-only packet is received during data exchange in
read_nonraw(), a new rx head is calculated but the rx queue head is not
actually advanced (rx_set_head() is not called) and a branch is taken to
'no_data' at which point two things can happen depending on the value
of the newly calculated rx head and the current rx tail:
- If the rx queue is determined to be not empty, then the wrong packet
is picked up.
- If the rx queue is determined to be empty, then a read error (EAGAIN)
is eventually returned since it is falsely assumed that more data was
expected.
The fix is to update the rx head and return in case of a control only
packet during data exchange.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Aaron Young <aaron.young@oracle.com>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Reviewed-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 9cc91f212111cdcbefa02dcdb7dd443f224bf52c ]
The improved type-checking version of container_of() triggers a warning for
xchg_xen_ulong, pointing out that 'xen_ulong_t' is unsigned, but atomic64_t
contains a signed value:
drivers/xen/events/events_2l.c: In function 'evtchn_2l_handle_events':
drivers/xen/events/events_2l.c:187:1020: error: call to '__compiletime_assert_187' declared with attribute error: pointer type mismatch in container_of()
This adds a cast to work around the warning.
Cc: Ian Abbott <abbotti@mev.co.uk>
Fixes: 85323a991d40 ("xen: arm: mandate EABI and use generic atomic operations.")
Fixes: daa2ac80834d ("kernel.h: handle pointers to arrays better in container_of()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 698b851073ddf5a894910d63ca04605e0473414e ]
When ftrace is used with kprobes, it is possible for a kprobe to contain
an invalid location (ie. only initialised to 0 and not to a specific
location in the code). Trying to perform a cache flush on such location
leads to a crash r4k_flush_icache_range().
Fixes: c1bf207d6ee1 ("MIPS: kprobe: Add support.")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16296/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 71eb989ab5a110df8bcbb9609bacde73feacbedd ]
fixrange_init operates at PMD-granularity and expects the addresses to
be PMD-size aligned, but currently that might not be the case for
PKMAP_BASE unless it is defined properly, so ensure a correct alignment
is used before passing the address to fixrange_init.
fixed mappings: only align the start address that is passed to
fixrange_init rather than the value before adding the size, as we may
end up with uninitialised upper part of the range.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 99acc9bede06bbb2662aafff51f5b9e529fa845e ]
If a process dumps core while it has SPU contexts active then we have
code to also dump information about the SPU contexts.
Unfortunately it's been broken for 3 1/2 years, and we didn't notice. In
commit 7b1f4020d0d1 ("spufs: get rid of dump_emit() wrappers") the nread
variable was removed and rc used instead. That means when the loop exits
successfully, rc has the number of bytes read, but it's then used as the
return value for the function, which should return 0 on success.
So fix it by setting rc = 0 before returning in the success case.
Fixes: 7b1f4020d0d1 ("spufs: get rid of dump_emit() wrappers")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
present
[ Upstream commit d9c1b5431d5f0e07575db785a022bce91051ac1d ]
This is a fix for the problem [1], where VMCB.CPL was set to 0 and interrupt
was taken on userspace stack. The root cause lies in the specific AMD CPU
behaviour which manifests itself as unusable segment attributes on SYSRET.
The corresponding work around for the kernel is the following:
61f01dd941ba ("x86_64, asm: Work around AMD SYSRET SS descriptor attribute issue")
In other turn virtualization side treated unusable segment incorrectly and
restored CPL from SS attributes, which were zeroed out few lines above.
In current patch it is assured only that P bit is cleared in VMCB.save state
and segment attributes are not zeroed out if segment is not presented or is
unusable, therefore CPL can be safely restored from DPL field.
This is only one part of the fix, since QEMU side should be fixed accordingly
not to zero out attributes on its side. Corresponding patch will follow.
[1] Message id: CAJrWOzD6Xq==b-zYCDdFLgSRMPM-NkNuTSDFEtX=7MreT45i7Q@mail.gmail.com
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Mikhail Sennikovskii <mikhail.sennikovskii@profitbricks.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 5f16a046f8e144c294ef98cd29d9458b5f8273e5 ]
FUTEX_OP_OPARG_SHIFT instructs the futex code to treat the 12-bit oparg
field as a shift value, potentially leading to a left shift value that
is negative or with an absolute value that is significantly larger then
the size of the type. UBSAN chokes with:
================================================================================
UBSAN: Undefined behaviour in ./arch/arm64/include/asm/futex.h:60:13
shift exponent -1 is negative
CPU: 1 PID: 1449 Comm: syz-executor0 Not tainted 4.11.0-rc4-00005-g977eb52-dirty #11
Hardware name: linux,dummy-virt (DT)
Call trace:
[<ffff200008094778>] dump_backtrace+0x0/0x538 arch/arm64/kernel/traps.c:73
[<ffff200008094cd0>] show_stack+0x20/0x30 arch/arm64/kernel/traps.c:228
[<ffff200008c194a8>] __dump_stack lib/dump_stack.c:16 [inline]
[<ffff200008c194a8>] dump_stack+0x120/0x188 lib/dump_stack.c:52
[<ffff200008cc24b8>] ubsan_epilogue+0x18/0x98 lib/ubsan.c:164
[<ffff200008cc3098>] __ubsan_handle_shift_out_of_bounds+0x250/0x294 lib/ubsan.c:421
[<ffff20000832002c>] futex_atomic_op_inuser arch/arm64/include/asm/futex.h:60 [inline]
[<ffff20000832002c>] futex_wake_op kernel/futex.c:1489 [inline]
[<ffff20000832002c>] do_futex+0x137c/0x1740 kernel/futex.c:3231
[<ffff200008320504>] SYSC_futex kernel/futex.c:3281 [inline]
[<ffff200008320504>] SyS_futex+0x114/0x268 kernel/futex.c:3249
[<ffff200008084770>] el0_svc_naked+0x24/0x28
================================================================================
syz-executor1 uses obsolete (PF_INET,SOCK_PACKET)
sock: process `syz-executor0' is using obsolete setsockopt SO_BSDCOMPAT
This patch attempts to fix some of this by:
* Making encoded_op an unsigned type, so we can shift it left even if
the top bit is set.
* Casting to signed prior to shifting right when extracting oparg
and cmparg
* Consider only the bottom 5 bits of oparg when using it as a left-shift
value.
Whilst I think this catches all of the issues, I'd much prefer to remove
this stuff, as I think it's unused and the bugs are copy-pasted between
a bunch of architectures.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 6e2f03e292ef46eed2b31b0a344a91d514f9cd81 ]
Prevent a kernel panic caused by unintentionally clearing TCR watchdog
bits. At this point in the kernel boot, the watchdog may have already
been enabled by u-boot. The original code's attempt to write to the TCR
register results in an inadvertent clearing of the watchdog
configuration bits, causing the 476 to reset.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit d5c7b4d5ac2237a6da7ced3adfe6b8bf769f8cc6 ]
Commit a22950c888e3 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e1d39b17e044e8ae819827810d87d809ba5f58c0 ]
The decision whether or not to exit from L2 to L1 on an lmsw instruction is
based on bogus values: instead of using the information encoded within the
exit qualification, it uses the data also used for the mov-to-cr
instruction, which boils down to using whatever is in %eax at that point.
Use the correct values instead.
Without this fix, an L1 may not get notified when a 32-bit Linux L2
switches its secondary CPUs to protected mode; the L1 is only notified on
the next modification of CR0. This short time window poses a problem, when
there is some other reason to exit to L1 in between. Then, L2 will be
resumed in real mode and chaos ensues.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit f97f03578b997a8ec2b9bc4928f958a865137268 ]
The DSP device on Davinci platforms does not have an MMU and requires
specific DDR memory to boot. This memory is reserved using the rproc_mem
kernel boot parameter and is assigned to the device on non-DT boots.
The remoteproc core uses the DMA API and so will fall back to assigning
random memory if this memory is not assigned to the device, but the DSP
remote processor boot will not be successful in such cases. So, check
that memory has been reserved and assigned to the device specifically
before even creating the DSP device.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 79935915300c5eb88a0e94fa9148a7505c14a02a ]
When running a stress playback/stop loop test on a mx6wandboard channel
swaps can be noticed randomly.
Increasing the SGTL5000 LRCLK pad strength to its maximum value fixes
the issue, so add the 'lrclk-strength' property to avoid the audio
channel swaps.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 8309f86cd41e8714526867177facf7a316d9be53 ]
Since the clocksource watchdog will only detect broken TSC after the
fact, all TSC based clocks will likely have observed non-continuous
values before/when switching away from TSC.
Therefore only thing to fully avoid random clock movement when your
BIOS randomly mucks with TSC values from SMI handlers is reporting the
TSC as unstable at boot.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 67325e988faea735d663799b6d152b5f4254093c ]
The PR KVM implementation of the PAPR HPT hypercalls (H_ENTER etc.)
access an image of the HPT in userspace memory using copy_from_user
and copy_to_user. Recently, the declarations of those functions were
annotated to indicate that the return value must be checked. Since
this code doesn't currently check the return value, this causes
compile warnings like the ones shown below, and since on PPC the
default is to compile arch/powerpc with -Werror, this causes the
build to fail.
To fix this, we check the return values, and if non-zero, fail the
hypercall being processed with a H_FUNCTION error return value.
There is really no good error return value to use since PAPR didn't
envisage the possibility that the hypervisor may not be able to access
the guest's HPT, and H_FUNCTION (function not supported) seems as
good as any.
The typical compile warnings look like this:
CC arch/powerpc/kvm/book3s_pr_papr.o
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c: In function ‘kvmppc_h_pr_enter’:
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c:53:2: error: ignoring return value of ‘copy_from_user’, declared with attribute warn_unused_result [-Werror=unused-result]
copy_from_user(pteg, (void __user *)pteg_addr, sizeof(pteg));
^
/home/paulus/kernel/kvm/arch/powerpc/kvm/book3s_pr_papr.c:74:2: error: ignoring return value of ‘copy_to_user’, declared with attribute warn_unused_result [-Werror=unused-result]
copy_to_user((void __user *)pteg_addr, hpte, HPTE_SIZE);
^
... etc.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit d04a4c76f71dd5335f8e499b59617382d84e2b8d ]
The perf tool assumes that kernel symbols are never present at address
zero. In fact it assumes if functions that map symbols to addresses
return zero, that the symbol was not found.
Given that s390's _text symbol historically is located at address zero
this yields at least a couple of false errors and warnings in one of
perf's test cases about not present symbols ("perf test 1").
To fix this simply move the _text symbol to address 0x200, just behind
the initial psw and channel program located at the beginning of the
kernel image. This is now hard coded within the linker script.
I tried a nicer solution which moves the initial psw and channel
program into an own section. However that would move the symbols
within the "real" head.text section to different addresses, since the
".org" statements within head.S are relative to the head.text
section. If there is a new section in front, everything else will be
moved. Alternatively I could have adjusted all ".org" statements. But
this current solution seems to be the easiest one, since nobody really
cares where the _text symbol is actually located.
Reported-by: Zvonko Kosic <zkosic@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 1f166499ce006b3770a3166122eda64e160736ab ]
The PMICs have POWERHOLD set by default which prevents PMIC shutdown
even on DEV_CTRL On bit set to 0 as the Powerhold has higher priority.
So to enable pmic power off this property lets one over ride the default
value and enable pmic power off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 7c62de5f3fc92291decc0dac5f36949bdc3fb575 ]
Add power hold and power controller properties to palmas node.
This is needed to shutdown pmic correctly on boards with
powerhold set.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 8f461b1e02ed546fbd0f11611138da67fd85a30f ]
With ecb-cast5-avx, if a 128+ byte scatterlist element followed a
shorter one, then the algorithm accidentally encrypted/decrypted only 8
bytes instead of the expected 128 bytes. Fix it by setting the
encryption/decryption 'fn' correctly.
Fixes: c12ab20b162c ("crypto: cast5/avx - avoid using temporary stack buffers")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 60b0a8c3d2480f3b57282b47b7cae7ee71c48635 ]
Commit 7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with
____cacheline_aligned_in_smp") removed a section specification from the
jiffies declaration that caused conflicts on some platforms.
Unfortunately this change broke the build for frv:
kernel/built-in.o: In function `__do_softirq': (.text+0x6460): relocation truncated to fit: R_FRV_GPREL12 against symbol
`jiffies' defined in *ABS* section in .tmp_vmlinux1
kernel/built-in.o: In function `__do_softirq': (.text+0x6574): relocation truncated to fit: R_FRV_GPREL12 against symbol
`jiffies' defined in *ABS* section in .tmp_vmlinux1
kernel/built-in.o: In function `pwq_activate_delayed_work': workqueue.c:(.text+0x15b9c): relocation truncated to fit: R_FRV_GPREL12 against
symbol `jiffies' defined in *ABS* section in .tmp_vmlinux1
...
Add __jiffy_arch_data to the declaration of jiffies and use it on frv to
include the section specification. For all other platforms
__jiffy_arch_data (currently) has no effect.
Fixes: 7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp")
Link: http://lkml.kernel.org/r/20170516221333.177280-1-mka@chromium.org
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c93f5cf571e7795f97d49ef51b766cf25e328545 ]
Fix kprobes to set(recover) RWX bits correctly on trampoline
buffer before releasing it. Releasing readonly page to
module_memfree() crash the kernel.
Without this fix, if kprobes user register a bunch of kprobes
in function body (since kprobes on function entry usually
use ftrace) and unregister it, kernel hits a BUG and crash.
Link: http://lkml.kernel.org/r/149570868652.3518.14120169373590420503.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Fixes: d0381c81c2f7 ("kprobes/x86: Set kprobes pages read-only")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 6007b080d2e2adb7af22bf29165f0594ea12b34c ]
In Cilium some of the main programs we run today are hitting 9 passes
on x64's JIT compiler, and we've had cases already where we surpassed
the limit where the JIT then punts the program to the interpreter
instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON
or insertion failures due to the prog array owner being JITed but the
program to insert not (both must have the same JITed/non-JITed property).
One concrete case the program image shrunk from 12,767 bytes down to
10,288 bytes where the image converged after 16 steps. I've measured
that this took 340us in the JIT until it converges on my i7-6600U. Thus,
increase the original limit we had from day one where the JIT covered
cBPF only back then before we run into the case (as similar with the
complexity limit) where we trip over this and hit program rejections.
Also add a cond_resched() into the compilation loop, the JIT process
runs without any locks and may sleep anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e5ea9b54a055619160bbfe527ebb7d7191823d66 ]
We intended to clear the lowest 6 bits but because of a type bug we
clear the high 32 bits as well. Andi says that periods are rarely more
than U32_MAX so this bug probably doesn't have a huge runtime impact.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 294fe0f52a44 ("perf/x86/intel: Add INST_RETIRED.ALL workarounds")
Link: http://lkml.kernel.org/r/20180317115216.GB4035@mwanda
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c55b8550fa57ba4f5e507be406ff9fc2845713e8 ]
Since the x86-64 kernel must be aligned to 2MB, refuse to boot the
kernel if the alignment of the LOAD segment isn't a multiple of 2MB.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/CAMe9rOrR7xSJgUfiCoZLuqWUwymRxXPoGBW38%2BpN%3D9g%2ByKNhZw@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e3d03598e8ae7d195af5d3d049596dec336f569f ]
Binutils 2.31 will enable -z separate-code by default for x86 to avoid
mixing code pages with data to improve cache performance as well as
security. To reduce x86-64 executable and shared object sizes, the
maximum page size is reduced from 2MB to 4KB. But x86-64 kernel must
be aligned to 2MB. Pass -z max-page-size=0x200000 to linker to force
2MB page size regardless of the default page size used by linker.
Tested with Linux kernel 4.15.6 on x86-64.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/CAMe9rOp4_%3D_8twdpTyAP2DhONOCeaTOsniJLoppzhoNptL8xzA@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 32d43cd391bacb5f0814c2624399a5dad3501d09 ]
The undocumented 'icebp' instruction (aka 'int1') works pretty much like
'int3' in the absense of in-circuit probing equipment (except,
obviously, that it raises #DB instead of raising #BP), and is used by
some validation test-suites as such.
But Andy Lutomirski noticed that his test suite acted differently in kvm
than on bare hardware.
The reason is that kvm used an inexact test for the icebp instruction:
it just assumed that an all-zero VM exit qualification value meant that
the VM exit was due to icebp.
That is not unlike the guess that do_debug() does for the actual
exception handling case, but it's purely a heuristic, not an absolute
rule. do_debug() does it because it wants to ascribe _some_ reasons to
the #DB that happened, and an empty %dr6 value means that 'icebp' is the
most likely casue and we have no better information.
But kvm can just do it right, because unlike the do_debug() case, kvm
actually sees the real reason for the #DB in the VM-exit interruption
information field.
So instead of relying on an inexact heuristic, just use the actual VM
exit information that says "it was 'icebp'".
Right now the 'icebp' instruction isn't technically documented by Intel,
but that will hopefully change. The special "privileged software
exception" information _is_ actually mentioned in the Intel SDM, even
though the cause of it isn't enumerated.
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit c82084117f79bcae085e40da526253736a247120 ]
Set the resource type when we reserve VGA-related I/O port resources.
The resource code doesn't actually look at the type, so it inserts
resources without a type in the tree correctly even without this change.
But if we ever print a resource without a type, it looks like this:
vga+ [??? 0x000003c0-0x000003df flags 0x0]
Setting the type means it will be printed correctly as:
vga+ [io 0x000003c0-0x000003df]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit a25fb8508c1b80dce742dbeaa4d75a1e9f2c5617 ]
Starting from gcc-5.4+ gcc generates MLX instructions in more cases to
refer local symbols:
https://gcc.gnu.org/PR60465
That caused ia64 module loader to choke on such instructions:
fuse: invalid slot number 1 for IMM64
The Linux kernel used to handle only case where relocation pointed to
slot=2 instruction in the bundle. That limitation was fixed in linux by
commit 9c184a073bfd ("[IA64] Fix 2.6 kernel for the new ia64 assembler")
See
http://sources.redhat.com/bugzilla/show_bug.cgi?id=1433
This change lifts the slot=2 restriction from the kernel module loader.
Tested on 'fuse' and 'btrfs' kernel modules.
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: H J Lu <hjl.tools@gmail.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Bug: https://bugs.gentoo.org/601014
Tested-by: Émeric MASCHINO <emeric.maschino@gmail.com>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 2c949ce38f4e81d7487f165fa3b8f77d74a2a6c4 ]
The PCIe programming sequence in TRM suggests CLKSTCTRL of PCIe should be
set to SW_WKUP. There are no issues when CLKSTCTRL is set to HW_AUTO in RC
mode. However in EP mode, the host system is not able to access the
MEMSPACE and setting the CLKSTCTRL to SW_WKUP fixes it.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 6f05d0761af612e04572ba4d65b4c0274a88444f ]
The support for dynamic ftrace with CONFIG_DEBUG_RODATA involves
overriding the weak arch_ftrace_update_code() with a variant which makes
the kernel text writable around the patching.
This override was however added under the CONFIG_OLD_MCOUNT ifdef, and
CONFIG_OLD_MCOUNT is only enabled if frame pointers are enabled.
This leads to non-functional dynamic ftrace (ftrace triggers a
WARN_ON()) when CONFIG_DEBUG_RODATA is enabled and CONFIG_FRAME_POINTER
is not.
Move the override out of that ifdef and into the CONFIG_DYNAMIC_FTRACE
ifdef where it belongs.
Fixes: 80d6b0c2eed2a ("ARM: mm: allow text and rodata sections to be read-only")
Suggested-by: Nicolai Stange <nicstange@gmail.com>
Suggested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Abel Vesa <abelvesa@gmail.com>
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit bd9166ffe624000140fc6b606b256df01fc0d060 ]
At the moment kvmppc_mmu_map_page() returns -1 if
mmu_hash_ops.hpte_insert() fails for any reason so the page fault handler
resumes the guest and it faults on the same address again.
This adds distinction to kvmppc_mmu_map_page() to return -EIO if
mmu_hash_ops.hpte_insert() failed for a reason other than full pteg.
At the moment only pSeries_lpar_hpte_insert() returns -2 if
plpar_pte_enter() failed with a code other than H_PTEG_FULL.
Other mmu_hash_ops.hpte_insert() instances can only fail with
-1 "full pteg".
With this change, if PR KVM fails to update HPT, it can signal
the userspace about this instead of returning to guest and having
the very same page fault over and over again.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 7ee06cb2f840a96be46233181ed4557901a74385 ]
The classic PC rtc-coms driver has a workaround for broken ACPI device
nodes for it which lack an irq resource. This workaround used to
unconditionally hardcode the irq to 8 in these cases.
This was causing irq conflict problems on systems without a legacy-pic
so a recent patch added an if (nr_legacy_irqs()) guard to the
workaround to avoid this irq conflict.
nr_legacy_irqs() uses the legacy_pic symbol under the hood causing
an undefined symbol error if the rtc-cmos code is build as a module.
This commit exports the legacy_pic symbol to fix this.
Cc: rtc-linux@googlegroups.com
Cc: alexandre.belloni@free-electrons.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 18a955219bf7d9008ce480d4451b6b8bf4483a22 ]
Gratian Crisan reported that vmalloc_fault() crashes when CONFIG_HUGETLBFS
is not set since the function inadvertently uses pXn_huge(), which always
return 0 in this case. ioremap() does not depend on CONFIG_HUGETLBFS.
Fix vmalloc_fault() to call pXd_large() instead.
Fixes: f4eafd8bcd52 ("x86/mm: Fix vmalloc_fault() to handle large pages properly")
Reported-by: Gratian Crisan <gratian.crisan@ni.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Link: https://lkml.kernel.org/r/20180313170347.3829-2-toshi.kani@hpe.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit 7be4b5dc7ffa9499ac6ef33a5ffa9ff43f9b7057 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2b9 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit e153db03c6b7a035c797bcdf35262586f003ee93 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
|
[ Upstream commit d0381c81c2f782fa2131178d11e0cfb23d50d631 ]
Set the pages which is used for kprobes' singlestep buffer
and optprobe's trampoline instruction buffer to readonly.
This can prevent unexpected (or unintended) instruction
modification.
This also passes rodata_test as below.
Without this patch, rodata_test shows a warning:
WARNING: CPU: 0 PID: 1 at arch/x86/mm/dump_pagetables.c:235 note_page+0x7a9/0xa20
x86/mm: Found insecure W+X mapping at address ffffffffa0000000/0xffffffffa0000000
With this fix, no W+X pages are found:
x86/mm: Checked W+X mappings: passed, no W+X pages found.
rodata_test: all tests were successful
Reported-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ye Xiaolong <xiaolong.ye@intel.com>
Link: http://lkml.kernel.org/r/149076375592.22469.14174394514338612247.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
|
