| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add example 64MByte long reservation in the first 512MBytes of physical
memory used as shared DMA pool.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
DT-enabled kernel should have a CPU node connected to a clock. This clock
is the CCOUNT clock. Use old platform_calibrate_ccount call as a fallback
when CPU node cannot be found or has no clock and in non-DT-enabled
configurations.
Drop no longer needed code that updates CPU clock-frequency property in
the DT; drop DT-related code from the platform_calibrate_ccount too.
Move of_clk_init to the top of time_init, so that clocks are initialized
before CCOUNT calibration is attempted.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Instead of querying hardcoded FPGA frequency register and then updating
clock-frequency property in specificly named DT nodes in machine setup
code register a clock provider that returns fixed-rate clock, configured
by register specified in DT. This way we have less magic/hardcoded names
and use more existing common clock framework code.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add module parameter xilinx_uartps.rx_trigger_level=32 to command line
options for CSP to set Rx watermark for xuartps driver lower than the
default value, to avoid UART overruns at 115200 bps.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Added defconfig, device tree and Xtensa variant header files for the
Cadence Configurable System Platform "xt_lnx" processor configuration.
Signed-off-by: Scott Telford <stelford@cadence.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Serial port is attached to XTFPGA boards as native endian device, now
that earlycon parameter parser understands mmio32native put it into
earlycon kernel parameter. This makes early console functional on both
little- and big-endian CPUs with identical kernel command lines.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
I2C controller is attached to XTFPGA boards as native endian device, mark
it as such in DTS.
Set register width in DTS to 4, this way it works both for little- and
big-endian CPUs.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Ethernet controller is attached to XTFPGA boards as native endian device,
mark it as such in DTS and pass correct endianness in platform data.
This makes network functional on big-endian CPUs.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Serial port is attached to XTFPGA boards as native endian device, mark
it as such in DTS and pass correct endianness in platform data.
Set register width in DTS to 4, this way it matches the platform data
and works correctly on big-endian CPUs.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Pull xtensa updates from Chris Zankel:
- fix remaining issues with noMMU cores
- fix build for cores w/o cache or zero overhead loop options
- fix boot of secondary cores in SMP configuration
- add support for DMA to high memory pages
- add dma_to_phys and phys_to_dma functions.
* tag 'xtensa-20151108' of git://github.com/czankel/xtensa-linux:
xtensa: implement dma_to_phys and phys_to_dma
xtensa: support DMA to high memory
Revert "xtensa: cache inquiry and unaligned cache handling functions"
xtensa: drop unused sections and remapped reset handlers
xtensa: fix secondary core boot in SMP
xtensa: add FORCE_MAX_ZONEORDER to Kconfig
xtensa: nommu: provide defconfig for de212 on kc705
xtensa: nommu: xtfpga: add kc705 DTS
xtensa: add de212 core variant
xtensa: nommu: select HAVE_FUTEX_CMPXCHG
xtensa: nommu: fix default memory start address
xtensa: nommu: provide correct KIO addresses
xtensa: nommu: fix USER_RING definition
xtensa: xtfpga: fix integer overflow in TASK_SIZE
xtensa: fix build for configs without cache options
xtensa: fixes for configs without loop option
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-xtensa@linux-xtensa.org
|
|
This includes OpenCores I2C host controller, TI CDCE706 clock generator,
xtfpga I2S master controller, xtfpga SPI master controller, TI TLV320AIC23
audio codec and a simple audio card.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
This config allows running SMP-enabled bitstream on LX200 board.
NFS or FLASH rootfs, minimal debug, up to 4 cores.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Enable all memory available on KC705 (1G - 128M) by default. Update memory
node in DTS and also limit usable memory in bootargs in case memmap is
passed from the bootloader.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Connect xtfpga board ethernet MAC to the clock in the DTS. Set up MAC
base frequency in the platform data in case of build w/o CONFIG_OF.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
With this change the board needs to set up single clock object, users of
this clock will get correct frequency automatically.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
The recommended compatible string format, according to the ePAPR v1.1 standard,
is "manufacturer,model". Change the xtensa cpu compatible strings to
"cdns,xtensa-cpu". Also, change the boards compatible strings in a similar way.
The pic compatible string will be dealt with in a separate patch.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
Extract xtensa built-in interrupt controller implementation from
xtensa/kernel/irq.c and move it to other irqchips, providing way to
instantiate it from the device tree.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
The current rules have the .dtb files build in a different directory
from the .dts files. This patch changes xtensa to use the generic dtb
rule which builds .dtb files in the same directory as the source .dts.
This requires moving parts of arch/xtensa/boot/Makefile into newly
created arch/xtensa/boot/dts/Makefile, and updating arch/xtensa/Makefile
to call the new Makefile.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
|
Add common XTFPGA parts as *.dtsi (base board, flash) and DTS for LX60
and for ML605.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
|
