| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 7aafac11e308d37ed3c509829bb43d80c1811ac3 ]
The IODA2 specification says that a 64 DMA address cannot use top 4 bits
(3 are reserved and one is a "TVE select"); bottom page_shift bits
cannot be used for multilevel table addressing either.
The existing IODA2 table allocation code aligns the minimum TCE table
size to PAGE_SIZE so in the case of 64K system pages and 4K IOMMU pages,
we have 64-4-12=48 bits. Since 64K page stores 8192 TCEs, i.e. needs
13 bits, the maximum number of levels is 48/13 = 3 so we physically
cannot address more and EEH happens on DMA accesses.
This adds a check that too many levels were requested.
It is still possible to have 5 levels in the case of 4K system page size.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bc74f1ccd457832dc515fc1febe6655985fdcd2 upstream.
When PCI bus is unplugged during full hotplug for EEH recovery,
the platform PE instance (struct pnv_ioda_pe) isn't released and
it dereferences the stale PCI bus that has been released. It leads
to kernel crash when referring to the stale PCI bus.
This fixes the issue by correcting the PE's primary bus when it's
oneline at plugging time, in pnv_pci_dma_bus_setup() which is to
be called by pcibios_fixup_bus().
Reported-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Tested-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 32-bit TCE table initialization relies on the DMA window having a
size equal to a power of 2 (and checks for it explicitly). But
crashkernel= has no constraint that requires a power-of-2 be specified.
This causes the kdump kernel to fail to boot as none of the PCI devices
(including the disk controller) are successfully initialized.
After this change, the PCI devices successfully set up the 32-bit TCE
table and kdump succeeds.
Fixes: aca6913f5551 ("powerpc/powernv/ioda2: Introduce helpers to allocate TCE pages")
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 4.2
Tested-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When attempting to kdump with the 4.2 kernel, we see for each PCI
device:
pci 0003:01 : [PE# 000] Assign DMA32 space
pci 0003:01 : [PE# 000] Setting up 32-bit TCE table at 0..80000000
pci 0003:01 : [PE# 000] Failed to create 32-bit TCE table, err -22
PCI: Domain 0004 has 8 available 32-bit DMA segments
PCI: 4 PE# for a total weight of 70
pci 0004:01 : [PE# 002] Assign DMA32 space
pci 0004:01 : [PE# 002] Setting up 32-bit TCE table at 0..80000000
pci 0004:01 : [PE# 002] Failed to create 32-bit TCE table, err -22
pci 0004:0d : [PE# 005] Assign DMA32 space
pci 0004:0d : [PE# 005] Setting up 32-bit TCE table at 0..80000000
pci 0004:0d : [PE# 005] Failed to create 32-bit TCE table, err -22
pci 0004:0e : [PE# 006] Assign DMA32 space
pci 0004:0e : [PE# 006] Setting up 32-bit TCE table at 0..80000000
pci 0004:0e : [PE# 006] Failed to create 32-bit TCE table, err -22
pci 0004:10 : [PE# 008] Assign DMA32 space
pci 0004:10 : [PE# 008] Setting up 32-bit TCE table at 0..80000000
pci 0004:10 : [PE# 008] Failed to create 32-bit TCE table, err -22
and eventually the kdump kernel fails to boot as none of the PCI devices
(including the disk controller) are successfully initialized.
The EINVAL response is because the DMA window (the 2GB base window) is
larger than the kdump kernel's reserved memory (crashkernel=, in this
case specified to be 1024M). The check in question,
if ((window_size > memory_hotplug_max()) || !is_power_of_2(window_size))
is a valid sanity check for pnv_pci_ioda2_table_alloc_pages(), so adjust
the caller to pass in a smaller window size if our maximum memory value
is smaller than the DMA window.
After this change, the PCI devices successfully set up the 32-bit TCE
table and kdump succeeds.
The problem was seen on a Firestone machine originally.
Fixes: aca6913f5551 ("powerpc/powernv/ioda2: Introduce helpers to allocate TCE pages")
Cc: stable@vger.kernel.org # 4.2
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Coding style pedantry, use u64, change the indentation]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
from Benjamin Herrenschmidt
- EEH fixes for SRIOV from Gavin
- introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth
- use hardware RNG for arch_get_random_seed_* not arch_get_random_*
from Paul Mackerras
- seccomp filter support from Michael Ellerman
- opal_cec_reboot2() handling for HMIs & machine checks from Mahesh
Salgaonkar
- add powerpc timebase as a trace clock source from Naveen N. Rao
- misc cleanups in the xmon, signal & SLB code from Anshuman Khandual
- add an inline function to update POWER8 HID0 from Gautham R. Shenoy
- fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman
- drop support for 64K local store on 4K kernels from Michael Ellerman
- move dma_get_required_mask() from pnv_phb to pci_controller_ops from
Andrew Donnellan
- initialize distance lookup table from drconf path from Nikunj A
Dadhania
- enable RTC class support from Vaibhav Jain
- disable automatically blocked PCI config from Gavin Shan
- add LEDs driver for PowerNV platform from Vasant Hegde
- fix endianness issues in the HVSI driver from Laurent Dufour
- kexec endian fixes from Samuel Mendoza-Jonas
- fix corrupted pdn list from Gavin Shan
- fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan
- Freescale updates from Scott: Highlights include 32-bit memcpy/memset
optimizations, checksum optimizations, 85xx config fragments and
updates, device tree updates, e6500 fixes for non-SMP, and misc
cleanup and minor fixes.
- a ton of cxl updates & fixes:
- add explicit precision specifiers from Rasmus Villemoes
- use more common format specifier from Rasmus Villemoes
- destroy cxl_adapter_idr on module_exit from Johannes Thumshirn
- destroy afu->contexts_idr on release of an afu from Johannes
Thumshirn
- compile with -Werror from Daniel Axtens
- EEH support from Daniel Axtens
- plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain
- add alternate MMIO error handling from Ian Munsie
- allow release of contexts which have been OPENED but not STARTED
from Andrew Donnellan
- remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar
- release irqs if memory allocation fails from Vaibhav Jain
- remove racy attempt to force EEH invocation in reset from Daniel
Axtens
- fix + cleanup error paths in cxl_dev_context_init from Ian Munsie
- fix force unmapping mmaps of contexts allocated through the kernel
api from Ian Munsie
- set up and enable PSL Timebase from Philippe Bergheaud
* tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits)
cxl: Set up and enable PSL Timebase
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
cxl: Fix + cleanup error paths in cxl_dev_context_init
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
powerpc/pseries: Fix corrupted pdn list
powerpc/powernv: Enable LEDS support
powerpc/iommu: Set default DMA offset in dma_dev_setup
cxl: Remove racy attempt to force EEH invocation in reset
cxl: Release irqs if memory allocation fails
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
powerpc/powernv: Reset HILE before kexec_sequence()
powerpc/kexec: Reset secondary cpu endianness before kexec
powerpc/hvsi: Fix endianness issues in the HVSI driver
leds/powernv: Add driver for PowerNV platform
powerpc/powernv: Create LED platform device
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
powerpc/powernv: Fix the log message when disabling VF
cxl: Allow release of contexts which have been OPENED but not STARTED
...
|
|
Commit e91c25111aa3 "powerpc/iommu: Cleanup setting of DMA base/offset"
expects that the default DMA offset is set from pnv_ioda_setup_bus_dma()
which is correct unless it is SRIOV where the code flow is different -
at the moment when pnv_ioda_setup_bus_dma() is called, PCI devices for
VFs are not created yet.
This adds missing set_dma_offset() to pnv_pci_ioda_dma_dev_setup() to
cover the case of SRIOV.
Note that we still need set_dma_offset() in pnv_ioda_setup_bus_dma() as
at the boot time pnv_pci_ioda_dma_dev_setup() is called when no PE was
created yet, this happens at the PHB fixup stage.
Fixes: e91c25111aa3 ("powerpc/iommu: Cleanup setting of DMA base/offset")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On powernv platform, IOV BAR would be shifted if necessary. While the log
message is not correct when disabling VFs.
This patch fixes this by print correct message based on the offset value.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit 763d2d8df1ee ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The existing code stores the amount of memory allocated for a TCE table.
At the moment it uses @offset which is a virtual offset in the TCE table
which is only correct for a one level tables and it does not include
memory allocated for intermediate levels. When multilevel TCE table is
requested, WARN_ON in tce_iommu_create_table() prints a warning.
This adds an additional counter to pnv_pci_ioda2_table_do_alloc_pages()
to count actually allocated memory.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When releasing PE for SRIOV VF, the PE is forced to be frozen
wrongly. When the same PE is picked for another VF, it won't
work anyhow. The patch fixes the issue by unfreezing, not
freezing the VF PE when releasing it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The PELTV of PF PE should include VF PE, which is missed by current
code, so that the VF PE is frozen automatically when freezing PF PE.
The patch fixes the PELTV of PF PE to include VF PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On PHB3, PE might be reserved in advance to reflect the M64 segments
consumed by the PE according to M64 BARs (exclude VF BARs) of the PCI
devices included in the PE. The PE is picked based on M64 BARs instead
of the bridge's M64 windows, which might include VF BARs. Otherwise,
wrong PE could be picked.
The patch calculates the used M64 segments and PE numbers according to
the M64 BARs, excluding VF BARs, of PCI devices in one particular PE,
instead of the bridge's M64 windows. Then the right PE number is picked.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The patch changes the type of last argument of pnv_ioda_setup_bus_PE()
and phb::pick_m64_pe() to boolean. No functional change.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On PHB3, some PEs might be reserved in advance to reflect the M64
segments consumed by those PEs. We're reserving PEs based on the
M64 window of root port, which might contain VF BAR. The PEs for
VFs are allocated dynamically, not reserved based on the consumed
M64 segments. So the M64 window of root port isn't reliable for
the task. Instead, we go through M64 BARs (VF BARs excluded) of
PCI devices under the specified root bus and reserve PEs accordingly,
as the patch does.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The PE numbers are reserved according to root port's M64 window,
which is aligned to M64 segment finely. So one PE shouldn't be
reserved for multiple times. We will reserve PE numbers according
to the M64 BARs of PCI device in subsequent patches, which aren't
aligned to M64 segment size finely. It means one particular PE
could be reserved for multiple times.
The patch allows one PE to be reserved for multiple times and we
print the warning message at debugging level.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Now that the table and the offset can co-exist, we no longer need
to flip/flop, we can just establish both once at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When pnv_pci_ioda_fixup() is called during PHB fixup time, each PE in
the sorted list of PEs (phb::pe_dma_list) is iterated to setup the PE's
DMA32 space by pnv_ioda_setup_bus_dma() if the PE's DMA32 weight is bigger
than zero. The function also assigns all the subordinate PCI devices of
the PE's primary bus with the PE's DMA32 IOMMU table. It causes the PCI
devicess in the child PEs, which don't have DMA weight, receives wrong
IOMMU table and then IOMMU group.
The patch fixes above issue by more check on the PE's coverage and don't
assign IOMMU table to those PCI devices, which belong to the child PEs.
The problem was found on Firestone platform initially.
Suggested-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pnv_pci_ioda2_unset_window() function is used to do the final
cleanup of a DMA window being released:
- via VFIO ioctl by the guest request;
- via unplugging a virtual PCI function.
However the function was under #ifdef CONFIG_IOMMU_API and was missing.
This moves the helper outside of IOMMU_API block and enables it
for either or both IOMMU_API and PCI_IOV.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
control
Before the IOMMU user (VFIO) would take control over the IOMMU table
belonging to a specific IOMMU group. This approach did not allow sharing
tables between IOMMU groups attached to the same container.
This introduces a new IOMMU ownership flavour when the user can not
just control the existing IOMMU table but remove/create tables on demand.
If an IOMMU implements take/release_ownership() callbacks, this lets
the user have full control over the IOMMU group. When the ownership
is taken, the platform code removes all the windows so the caller must
create them.
Before returning the ownership back to the platform code, VFIO
unprograms and removes all the tables it created.
This changes IODA2's onwership handler to remove the existing table
rather than manipulating with the existing one. From now on,
iommu_take_ownership() and iommu_release_ownership() are only called
from the vfio_iommu_spapr_tce driver.
Old-style ownership is still supported allowing VFIO to run on older
P5IOC2 and IODA IO controllers.
No change in userspace-visible behaviour is expected. Since it recreates
TCE tables on each ownership change, related kernel traces will appear
more often.
This adds a pnv_pci_ioda2_setup_default_config() which is called
when PE is being configured at boot time and when the ownership is
passed from VFIO to the platform code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds a way for the IOMMU user to know how much a new table will
use so it can be accounted in the locked_vm limit before allocation
happens.
This stores the allocated table size in pnv_pci_ioda2_get_table_size()
so the locked_vm counter can be updated correctly when a table is
being disposed.
This defines an iommu_table_group_ops callback to let VFIO know
how much memory will be locked if a table is created.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The existing code programmed TVT#0 with some address and then
immediately released that memory.
This makes use of pnv_pci_ioda2_unset_window() and
pnv_pci_ioda2_set_bypass() which do correct resource release and
TVT update.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This extends iommu_table_group_ops by a set of callbacks to support
dynamic DMA windows management.
create_table() creates a TCE table with specific parameters.
it receives iommu_table_group to know nodeid in order to allocate
TCE table memory closer to the PHB. The exact format of allocated
multi-level table might be also specific to the PHB model (not
the case now though).
This callback calculated the DMA window offset on a PCI bus from @num
and stores it in a just created table.
set_window() sets the window at specified TVT index + @num on PHB.
unset_window() unsets the window from specified TVT.
This adds a free() callback to iommu_table_ops to free the memory
(potentially a tree of tables) allocated for the TCE table.
create_table() and free() are supposed to be called once per
VFIO container and set_window()/unset_window() are supposed to be
called for every group in a container.
This adds IOMMU capabilities to iommu_table_group such as default
32bit window parameters and others. This makes use of new values in
vfio_iommu_spapr_tce. IODA1/P5IOC2 do not support DDW so they do not
advertise pagemasks to the userspace.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
TCE tables might get too big in case of 4K IOMMU pages and DDW enabled
on huge guests (hundreds of GB of RAM) so the kernel might be unable to
allocate contiguous chunk of physical memory to store the TCE table.
To address this, POWER8 CPU (actually, IODA2) supports multi-level
TCE tables, up to 5 levels which splits the table into a tree of
smaller subtables.
This adds multi-level TCE tables support to
pnv_pci_ioda2_table_alloc_pages() and pnv_pci_ioda2_table_free_pages()
helpers.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This is a part of moving DMA window programming to an iommu_ops
callback. pnv_pci_ioda2_set_window() takes an iommu_table_group as
a first parameter (not pnv_ioda_pe) as it is going to be used as
a callback for VFIO DDW code.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This is a part of moving TCE table allocation into an iommu_ops
callback to support multiple IOMMU groups per one VFIO container.
This moves the code which allocates the actual TCE tables to helpers:
pnv_pci_ioda2_table_alloc_pages() and pnv_pci_ioda2_table_free_pages().
These do not allocate/free the iommu_table struct.
This enforces window size to be a power of two.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This moves iommu_table creation to the beginning to make following changes
easier to review. This starts using table parameters from the iommu_table
struct.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At the moment writing new TCE value to the IOMMU table fails with EBUSY
if there is a valid entry already. However PAPR specification allows
the guest to write new TCE value without clearing it first.
Another problem this patch is addressing is the use of pool locks for
external IOMMU users such as VFIO. The pool locks are to protect
DMA page allocator rather than entries and since the host kernel does
not control what pages are in use, there is no point in pool locks and
exchange()+put_page(oldtce) is sufficient to avoid possible races.
This adds an exchange() callback to iommu_table_ops which does the same
thing as set() plus it returns replaced TCE and DMA direction so
the caller can release the pages afterwards. The exchange() receives
a physical address unlike set() which receives linear mapping address;
and returns a physical address as the clear() does.
This implements exchange() for P5IOC2/IODA/IODA2. This adds a requirement
for a platform to have exchange() implemented in order to support VFIO.
This replaces iommu_tce_build() and iommu_clear_tce() with
a single iommu_tce_xchg().
This makes sure that TCE permission bits are not set in TCE passed to
IOMMU API as those are to be calculated by platform code from
DMA direction.
This moves SetPageDirty() to the IOMMU code to make it work for both
VFIO ioctl interface in in-kernel TCE acceleration (when it becomes
available later).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The iommu_table struct keeps a list of IOMMU groups it is used for.
At the moment there is just a single group attached but further
patches will add TCE table sharing. When sharing is enabled, TCE cache
in each PE needs to be invalidated so does the patch.
This does not change pnv_pci_ioda1_tce_invalidate() as there is no plan
to enable TCE table sharing on PHBs older than IODA2.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
At the moment the DMA setup code looks for the "ibm,opal-tce-kill"
property which contains the TCE kill register address. Writing to
this register invalidates TCE cache on IODA/IODA2 hub.
This moves the register address from iommu_table to pnv_pnb as this
register belongs to PHB and invalidates TCE cache for all tables of
all attached PEs.
This moves the property reading/remapping code to a helper which is
called when DMA is being configured for PE and which does DMA setup
for both IODA1 and IODA2.
This adds a new pnv_pci_ioda2_tce_invalidate_entire() helper which
invalidates cache for the entire table. It should be called after
every call to opal_pci_map_pe_dma_window(). It was not required before
because there was just a single TCE table and 64bit DMA was handled via
bypass window (which has no table so no cache was used) but this is going
to change with Dynamic DMA windows (DDW).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds tce_iommu_take_ownership() and tce_iommu_release_ownership
which call in a loop iommu_take_ownership()/iommu_release_ownership()
for every table on the group. As there is just one now, no change in
behaviour is expected.
At the moment the iommu_table struct has a set_bypass() which enables/
disables DMA bypass on IODA2 PHB. This is exposed to POWERPC IOMMU code
which calls this callback when external IOMMU users such as VFIO are
about to get over a PHB.
The set_bypass() callback is not really an iommu_table function but
IOMMU/PE function. This introduces a iommu_table_group_ops struct and
adds take_ownership()/release_ownership() callbacks to it which are
called when an external user takes/releases control over the IOMMU.
This replaces set_bypass() with ownership callbacks as it is not
necessarily just bypass enabling, it can be something else/more
so let's give it more generic name.
The callbacks is implemented for IODA2 only. Other platforms (P5IOC2,
IODA1) will use the old iommu_take_ownership/iommu_release_ownership API.
The following patches will replace iommu_take_ownership/
iommu_release_ownership calls in IODA2 with full IOMMU table release/
create.
As we here and touching bypass control, this removes
pnv_pci_ioda2_setup_bypass_pe() as it does not do much
more compared to pnv_pci_ioda2_set_bypass. This moves tce_bypass_base
initialization to pnv_pci_ioda2_setup_dma_pe.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
So far one TCE table could only be used by one IOMMU group. However
IODA2 hardware allows programming the same TCE table address to
multiple PE allowing sharing tables.
This replaces a single pointer to a group in a iommu_table struct
with a linked list of groups which provides the way of invalidating
TCE cache for every PE when an actual TCE table is updated. This adds
pnv_pci_link_table_and_group() and pnv_pci_unlink_table_and_group()
helpers to manage the list. However without VFIO, it is still going
to be a single IOMMU group per iommu_table.
This changes iommu_add_device() to add a device to a first group
from the group list of a table as it is only called from the platform
init code or PCI bus notifier and at these moments there is only
one group per table.
This does not change TCE invalidation code to loop through all
attached groups in order to simplify this patch and because
it is not really needed in most cases. IODA2 is fixed in a later
patch.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Modern IBM POWERPC systems support multiple (currently two) TCE tables
per IOMMU group (a.k.a. PE). This adds a iommu_table_group container
for TCE tables. Right now just one table is supported.
This defines iommu_table_group struct which stores pointers to
iommu_group and iommu_table(s). This replaces iommu_table with
iommu_table_group where iommu_table was used to identify a group:
- iommu_register_group();
- iommudata of generic iommu_group;
This removes @data from iommu_table as it_table_group provides
same access to pnv_ioda_pe.
For IODA, instead of embedding iommu_table, the new iommu_table_group
keeps pointers to those. The iommu_table structs are allocated
dynamically.
For P5IOC2, both iommu_table_group and iommu_table are embedded into
PE struct. As there is no EEH and SRIOV support for P5IOC2,
iommu_free_table() should not be called on iommu_table struct pointers
so we can keep it embedded in pnv_phb::p5ioc2.
For pSeries, this replaces multiple calls of kzalloc_node() with a new
iommu_pseries_alloc_group() helper and stores the table group struct
pointer into the pci_dn struct. For release, a iommu_table_free_group()
helper is added.
This moves iommu_table struct allocation from SR-IOV code to
the generic DMA initialization code in pnv_pci_ioda_setup_dma_pe and
pnv_pci_ioda2_setup_dma_pe as this is where DMA is actually initialized.
This change is here because those lines had to be changed anyway.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The pnv_pci_ioda_tce_invalidate() helper invalidates TCE cache. It is
supposed to be called on IODA1/2 and not called on p5ioc2. It receives
start and end host addresses of TCE table.
IODA2 actually needs PCI addresses to invalidate the cache. Those
can be calculated from host addresses but since we are going
to implement multi-level TCE tables, calculating PCI address from
a host address might get either tricky or ugly as TCE table remains flat
on PCI bus but not in RAM.
This moves pnv_pci_ioda_tce_invalidate() from generic pnv_tce_build/
pnt_tce_free and defines IODA1/2-specific callbacks which call generic
ones and do PHB-model-specific TCE cache invalidation. P5IOC2 keeps
using generic callbacks as before.
This changes pnv_pci_ioda2_tce_invalidate() to receives TCE index and
number of pages which are PCI addresses shifted by IOMMU page shift.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This adds a iommu_table_ops struct and puts pointer to it into
the iommu_table struct. This moves tce_build/tce_free/tce_get/tce_flush
callbacks from ppc_md to the new struct where they really belong to.
This adds the requirement for @it_ops to be initialized before calling
iommu_init_table() to make sure that we do not leave any IOMMU table
with iommu_table_ops uninitialized. This is not a parameter of
iommu_init_table() though as there will be cases when iommu_init_table()
will not be called on TCE tables, for example - VFIO.
This does s/tce_build/set/, s/tce_free/clear/ and removes "tce_"
redundant prefixes.
This removes tce_xxx_rm handlers from ppc_md but does not add
them to iommu_table_ops as this will be done later if we decide to
support TCE hypercalls in real mode. This removes _vm callbacks as
only virtual mode is supported by now so this also removes @rm parameter.
For pSeries, this always uses tce_buildmulti_pSeriesLP/
tce_buildmulti_pSeriesLP. This changes multi callback to fall back to
tce_build_pSeriesLP/tce_free_pSeriesLP if FW_FEATURE_MULTITCE is not
present. The reason for this is we still have to support "multitce=off"
boot parameter in disable_multitce() and we do not want to walk through
all IOMMU tables in the system and replace "multi" callbacks with single
ones.
For powernv, this defines _ops per PHB type which are P5IOC2/IODA1/IODA2.
This makes the callbacks for them public. Later patches will extend
callbacks for IODA1/2.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
So far an iommu_table lifetime was the same as PE. Dynamic DMA windows
will change this and iommu_free_table() will not always require
the group to be released.
This moves iommu_group_put() out of iommu_free_table().
This adds a iommu_pseries_free_table() helper which does
iommu_group_put() and iommu_free_table(). Later it will be
changed to receive a table_group and we will have to change less
lines then.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The existing code has 3 calls to iommu_register_group() and
all 3 branches actually cover all possible cases.
This replaces 3 calls with one and moves the registration earlier;
the latter will make more sense when we add TCE table sharing.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The set_iommu_table_base_and_group() name suggests that the function
sets table base and add a device to an IOMMU group.
The actual purpose for table base setting is to put some reference
into a device so later iommu_add_device() can get the IOMMU group
reference and the device to the group.
At the moment a group cannot be explicitly passed to iommu_add_device()
as we want it to work from the bus notifier, we can fix it later and
remove confusing calls of set_iommu_table_base().
This replaces set_iommu_table_base_and_group() with a couple of
set_iommu_table_base() + iommu_add_device() which makes reading the code
easier.
This adds few comments why set_iommu_table_base() and iommu_add_device()
are called where they are called.
For IODA1/2, this essentially removes iommu_add_device() call from
the pnv_pci_ioda_dma_dev_setup() as it will always fail at this particular
place:
- for physical PE, the device is already attached by iommu_add_device()
in pnv_pci_ioda_setup_dma_pe();
- for virtual PE, the sysfs entries are not ready to create all symlinks
so actual adding is happening in tce_iommu_bus_notifier.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This relies on the fact that a PCI device always has an IOMMU table
which may not be the case when we get dynamic DMA windows so
let's use more reliable check for IOMMU group here.
As we do not rely on the table presence here, remove the workaround
from pnv_pci_ioda2_set_bypass(); also remove the @add_to_iommu_group
parameter from pnv_ioda_setup_bus_dma().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This moves the current include file from cxl.h -> cxl-base.h. This current
include file is used only to pass information between the base driver that
needs to be built into the kernel and the cxl module.
This is to make way for a new include/misc/cxl.h which will
contain just the kernel API for other driver to use
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently pnv_pci_shutdown() calls the PHB shutdown code for all PHBs in the
system. It dereferences the private_data assuming it's a powernv PHB, which
won't be the case when we have different PHB in the systems (like when we add
vPHBs for CXL).
This moves the shutdown hook to the pci_controller_ops and fixes the call site
to use that instead.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Previously, dma_set_mask() on powernv was convoluted:
0) Call dma_set_mask() (a/p/kernel/dma.c)
1) In dma_set_mask(), ppc_md.dma_set_mask() exists, so call it.
2) On powernv, that function pointer is pnv_dma_set_mask().
In pnv_dma_set_mask(), the device is pci, so call pnv_pci_dma_set_mask().
3) In pnv_pci_dma_set_mask(), call pnv_phb->set_dma_mask() if it exists.
4) It only exists in the ioda case, where it points to
pnv_pci_ioda_dma_set_mask(), which is the final function.
So the call chain is:
dma_set_mask() ->
pnv_dma_set_mask() ->
pnv_pci_dma_set_mask() ->
pnv_pci_ioda_dma_set_mask()
Both ppc_md and pnv_phb function pointers are used.
Rip out the ppc_md call, pnv_dma_set_mask() and pnv_pci_dma_set_mask().
Instead:
0) Call dma_set_mask() (a/p/kernel/dma.c)
1) In dma_set_mask(), the device is pci, and pci_controller_ops.dma_set_mask()
exists, so call pci_controller_ops.dma_set_mask()
2) In the ioda case, that points to pnv_pci_ioda_dma_set_mask().
The new call chain is
dma_set_mask() ->
pnv_pci_ioda_dma_set_mask()
Now only the pci_controller_ops function pointer is used.
The fallback paths for p5ioc2 are the same.
Previously, pnv_pci_dma_set_mask() would find no pnv_phb->set_dma_mask()
function, to it would call __set_dma_mask().
Now, dma_set_mask() finds no ppc_md call or pci_controller_ops call,
so it calls __set_dma_mask().
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Remove powernv generic PCI controller operations. Replace it with
controller ops for each of the two supported PHBs.
As an added bonus, make the two new structs const, which will help
guard against bugs such as the one introduced in 65ebf4b63
("powerpc/powernv: Move controller ops from ppc_md to controller_ops")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Load the PowerNV platform pci controller ops into pci controllers
after all the operations are loaded into the platform ops struct, not
before.
Otherwise we aren't actually setting the ops properly which can break
IO for some devices.
Fixes: 65ebf4b63 ("powerpc/powernv: Move controller ops from ppc_md to controller_ops")
Reported-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc into next
Merge Richard's work to support SR-IOV on PowerNV. All generic PCI
patches acked by Bjorn.
Some minor conflicts with Daniel's pci_controller_ops work.
Conflicts:
arch/powerpc/include/asm/machdep.h
arch/powerpc/platforms/powernv/pci-ioda.c
|
|
This moves the PowerNV platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Merge in Gavin EEH fixes
|
|
If M64 has been supported, the prefetchable 64-bits memory resources
shouldn't be mapped to the corresponding PE# via M32DT. Unfortunately,
we're doing that in pnv_ioda_setup_pe_seg() wrongly. The issue was
introduced by commit 262af55 ("powerpc/powernv: Enable M64 aperatus
for PHB3"). The patch fixes the issue by simply skipping M64 resources
when updating to M32DT.
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In struct pci_dn, the pcidev field is assigned but not used, so remove it.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
When IOV BAR is big, each is covered by 4 M64 windows. This leads to
several VF PE sits in one PE in terms of M64.
Group VF PEs according to the M64 allocation.
[bhelgaas: use dev_printk() when possible]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
