summaryrefslogtreecommitdiff
path: root/arch/powerpc/platforms/52xx/mpc5200_simple.c
AgeCommit message (Collapse)AuthorFilesLines
2011-01-01of/flattree: Add of_flat_dt_match() helper functionGrant Likely1-11/+2
This patch adds of_flat_dt_match() which tests a node for compatibility with a list of values and converts the relevant powerpc platform code to use it. This approach simplifies the board support code a bit. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
2009-10-15mpc5200: support for the MAN mpc5200 based board mucmc52Heiko Schocher1-0/+1
- serial Console on PSC1 - 64MB SDRAM - MTD CFI Flash - Ethernet FEC - IDE support Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15mpc5200: support for the MAN mpc5200 based board uc101Heiko Schocher1-0/+1
- serial Console on PSC1 - 64MB SDRAM - MTD CFI Flash - Ethernet FEC - I2C with PCF8563 and Temp. Sensor ADM9240 - IDE support Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-03-11powerpc/5200: add Phytec phyCORE-MPC5200B-IO board (pcm032)Wolfram Sang1-1/+2
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-02-04powerpc/5200: Add support for the digsy MTC board.Grzegorz Bernacki1-0/+1
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC. Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-04-29[POWERPC] mpc5200: add Phytec pcm030 board supports.hauer@pengutronix.de1-0/+1
Add board support for the Phytec pcm030 mpc5200b based board. It does not need any platform specific fixups and as such is handled as a mpc5200 simple platform. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-27[POWERPC] Add common clock setting routine mpc52xx_psc_set_clkdiv()Grant Likely1-3/+3
PSC drivers should not access the CDM registers directly. Instead provide a common routine for setting the PSC clock parameters with the required locking. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-19[POWERPC] mpc5200: Add generic support for simple MPC5200 based boardsMarian Balakowicz1-0/+85
This patch adds support for 'mpc5200-simple-platform' compatible boards which do not need a platform specific setup. Such boards are supported assuming the following: - GPIO pins are configured by the firmware, - CDM configuration (clocking) is setup correctly by firmware, - if the 'fsl,has-wdt' property is present in one of the gpt nodes, then it is safe to use such gpt to reset the board, - PCI is supported if enabled in the kernel configuration and if there is a PCI bus node defined in the device tree. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
generated by cgit v1.2.3 (git 2.39.0) at 2025-09-03 11:41:23 +0300