| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Previously the FIFO on the stm32h743 usart was not utilized, because
the stm32f7 compatible configures it without FIFO support.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The stm32 spi driver tries to determine the fifo size of spi devices
dynamically. However, if the spi was already configured by the bootloader
the fifo size check can become an endless loop, because the driver
expects the spi to be in its initial "after device reset" state. The
driver does already support resetting the spi device at probe, thus this
patch adds only the required device tree properties
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Declare LTDC (display controller) on stm32h743.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The DH PDK2 has RTS/CTS lines available on UART8, describe them in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The QSPI CS2 is not used on DHCOM, remove the pinmux settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add extra RTS/CTS line pinmux for STM32MP1 UART8.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add support for Seeed Studio's stm32mp157c odyssey board.
Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
and carrier board with USB and ETH interfaces, SD card connector,
wifi and BT chip AP6236.
In this patch only basic kernel boot is supported and interfacing
SD card and on-board eMMC.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The KSZ9031 PHY skew timings for rxc/txc, originally set to achieve
the desired phase shift between clock- and data-signal, now trigger a
kernel warning when used in rgmii-id mode:
*-skew-ps values should be used only with phy-mode = "rgmii"
This is because commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode
support for the KSZ9031 PHY") now configures own timings when
phy-mode = "rgmii-id". Device trees wanting to set their own delays
should use phy-mode "rgmii" instead as the warning prescribes.
The "standard" timings now used with "rgmii-id" work fine on this
board, so drop the explicit timings in the device tree and thereby
silence the warning.
Fixes: 666b5ca85cd3 ("ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The DH PDK2 board is capable of USB OTG on the X14 USB Mini-AB connector,
fill in the missing bits to make USB OTG possible instead of peripheral.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The AV96 uses sdmmc2_d47_pins_c and sdmmc2_d47_sleep_pins_c, which
differ from sdmmc2_d47_pins_b and sdmmc2_d47_sleep_pins_b in one
pin, SDMMC2_D5, which is PA15 in the former and PA9 in the later.
The PA15 is correct on AV96, so fix this. This error is likely a
result of rebasing across the stm32mp1 DT pinctrl rework.
Fixes: 611325f68102 ("ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
The PHY and the VIO regulator is populated on the SoM, move it
into the SoM DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
If cpu_cluster_pm_enter() fails, we need to set MPU power domain back
to enabled to prevent the next WFI from potentially triggering an
undesired MPU power domain state change.
We already do this for omap_enter_idle_smp() but are missing it for
omap_enter_idle_coupled().
Fixes: 55be2f50336f ("ARM: OMAP2+: Handle errors for cpu_pm")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
|
|
Add a Device Tree for the RoseapplePi SBC.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The PPI interrupts for cortex-a9 were incorrectly specified, fix them.
Fixes: fdfe7f4f9d85 ("ARM: dts: Add Actions Semi S500 and LeMaker Guitar")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add Device Trees for Caninos Loucos Labrador CoM Core v2 and base board
M v1. Based on the work of Andreas Färber on Lemaker Guitar device tree.
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Most of the definitions for peripheral base addresses, interrupt and
DMA information is no longer used, so get rid of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that imx35 has been converted to a devicetree-only platform,
retrieve the IIM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that imx31 and imx35 has been converted to a devicetree-only platform,
retrieve the AVIC base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that imx31 and imx35 has been converted to a devicetree-only platform,
retrieve the CCM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that imx31 has been converted to a devicetree-only platform,
retrieve the IIM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that imx27 has been converted to a devicetree-only platform,
retrieve the CCM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that imx27 has been converted to a devicetree-only platform,
retrieve the SYSCTRL base address from devicetree.
To keep devicetree compatibilty the SYSCTRL base address will be
retrieved from the CCM base address plus an 0x800 offset.
This is not a problem as the imx27.dtsi describes the CCM register
range as 0x1000.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the native SPI chipselect on i.MX6 is known to be problematic.
Doing it on a imx6q-sabresd causes the SPI NOR probe to fail:
[ 5.388704] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00
Use the GPIO chipselect to avoid such problem.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add an entry for imx6q-logicpd.dtb so that it can be built by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It is standard practice to have a specific board compatible string, so
pass "logicpd,imx6q-logicpd".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix. While
touching the hogs, fix indentation (spaces -> tabs).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
port6 of mt7530 switch (= cpu port 0) on bananapi-r2 misses pause option
which causes rx drops on running iperf.
Fixes: f4ff257cd160 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200907070517.51715-1-linux@fw-web.de
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The msi_ctrl, io_optional and align_resource fields in struct hw_pci are
currently unused by arm/mach PCI host controller drivers and we won't
be adding any new users.
Remove them and related code.
Link: https://lore.kernel.org/r/20200904141607.4066-1-lorenzo.pieralisi@arm.com
Link: https://lore.kernel.org/r/20200916103045.28651-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
|
|
arch_scale_freq_invariant() is used by schedutil to determine whether
the scheduler's load-tracking signals are frequency invariant. Its
definition is overridable, though by default it is hardcoded to 'true'
if arch_scale_freq_capacity() is defined ('false' otherwise).
This behaviour is not overridden on arm, arm64 and other users of the
generic arch topology driver, which is somewhat precarious:
arch_scale_freq_capacity() will always be defined, yet not all cpufreq
drivers are guaranteed to drive the frequency invariance scale factor
setting. In other words, the load-tracking signals may very well *not*
be frequency invariant.
Now that cpufreq can be queried on whether the current driver is driving
the Frequency Invariance (FI) scale setting, the current situation can
be improved. This combines the query of whether cpufreq supports the
setting of the frequency scale factor, with whether all online CPUs are
counter-based FI enabled.
While cpufreq FI enablement applies at system level, for all CPUs,
counter-based FI support could also be used for only a subset of CPUs to
set the invariance scale factor. Therefore, if cpufreq-based FI support
is present, we consider the system to be invariant. If missing, we
require all online CPUs to be counter-based FI enabled in order for the
full system to be considered invariant.
If the system ends up not being invariant, a new condition is needed in
the counter initialization code that disables all scale factor setting
based on counters.
Precedence of counters over cpufreq use is not important here. The
invariant status is only given to the system if all CPUs have at least
one method of setting the frequency scale factor.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ipi_teardown() is only used when CONFIG_HOTPLUG_CPU is enabled.
Move the function to a location guarded by this config option.
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
|
|
The DMA offset notifier can only be used if PHYS_OFFSET is at least
KEYSTONE_HIGH_PHYS_START, which can't be represented by a 32-bit
phys_addr_t. Currently the code compiles fine despite that, a pending
change to the DMA offset handling would create a compiler warning for
this case. Add an ifdef to not compile the code except for LPAE
configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
|
|
Move the helpers to translate to and from direct mapping DMA addresses
to dma-direct.h. This not only is the most logical place, but the new
placement also avoids dependency loops with pending commits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
|
|
dma_to_virt is entirely unused, remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The __arch_page_to_dma hook is long gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
V3s contains crypto engine that is compatible with A33.
Add device tree node.
Signed-off-by: Martin Cerveny <m.cerveny@computer.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200907162458.23730-3-m.cerveny@computer.org
|
|
The sun8i-codec driver introduced a new set of DAPM widgets that more
accurately describe the hardware topology. Update the various device
trees to use the new widget names.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200726012557.38282-6-samuel@sholland.org
|
|
Allwinner R40 SoC has a video engine.
Add a node for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200825173523.1289379-6-jernej.skrabec@siol.net
|
|
SMB347 is a battery charger controller which is found on the Nexus 7
device.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Nexus 7 2012 has Elantech EKTF3624 touchscreen, this patch adds TS node to
the device-tree.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The default parent for all MMCs is PLLP, which is running at 408 MHz on
Tegra30 and 50 MHz clock can't be derived from PLLP. The maximum SDIO
clock rate is 50 MHz, but this rate isn't achievable using PLLP.
Let's switch the WiFi MMC clock parent to PLLC in order to get true 50
MHz. This patch doesn't fix any problems, it's just a minor improvement.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The default parent for all MMCs is PLLP, which is running at 216 MHz on
Tegra20 and 50 MHz clock can't be derived from PLLP. The maximum SDIO
clock rate is 50 MHz, but this rate isn't achievable using PLLP.
Let's switch the WiFi MMC clock parent to PLLC in order to get true 50
MHz. This patch doesn't fix any problems, it's just a minor improvement.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Previously 50MHz clock rate didn't work because of the wrong PINCTRL
configuration used for SDIO pins. Now the PINCTRL config is corrected
and the MMC clock rate could be bumped safely to 50MHz, increasing WiFi
TX throughput by 20 Mbit/s and allowing to hit the maximum 40 Mbit/s.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The low-power-mode drive was set to DIV_4 for some of PINCTRL groups,
while these groups should use DIV_1. This patch fixes the wrong PINCTRL
configurations and adds a full drive-setup for the changed configs, just
for completeness since the added values match the default configuration.
Now WiFi SDIO communication works properly using legacy signaling mode if
SDIO BUS clocked at 50MHz, which is a maximum SDIO clock rate on Tegra20.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This property was supposed to be upstreamed, but it was NAKed recently
in a favor to a better approach of firmware loading. It also turned
out that the firmware loading isn't really necessary because it's stored
in a non-volatile memory inside of the touchscreen controller and
previously the FW loading was needed in order to get touchscreen working,
but it actually was a TS driver problem which is resolved now. Hence
remove the unsupported property.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
MMC core now supports binding to a specific ID, which is very handy for
embedded devices, like Acer A500, because MMC ID may change depending on
kernel version or configuration which affects MMC driver probe order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
MMC core now supports binding to a specific ID, which is very handy for
embedded devices, like Nexus 7, because MMC ID may change depending on
kernel version or configuration which affects MMC driver probe order.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
