| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another small batch of fixes.
Most of these make zynq, socfpga and sunxi platforms work a bit
better:
- due to new requirements for regulators, DWMMC on socfpga broke past
v3.17
- SMP spinup fix for socfpga
- a few DT fixes for zynq
- another option (FIXED_REGULATOR) for sunxi is needed that used to
be selected by other options but no longer is.
- a couple of small DT fixes for at91
- ...and a couple for i.MX"
* tag 'armsoc-for-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
ARM: multi_v7_defconfig: enable CONFIG_MMC_DW_ROCKCHIP
ARM: sunxi_defconfig: enable CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
arm: socfpga: fix fetching cpu1start_addr for SMP
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.18" from Shawn Guo:
The i.MX fixes for 3.18:
- Revert one patch which increases I2C bus frequency on imx28-evk
- Fix a typo on imx6q EIM clock name
* tag 'imx-fixes-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-evk: Let i2c0 run at 100kHz
ARM: i.MX6: Fix "emi" clock name typo
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 78b81f4666fb ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues
when doing the following sequence in loop:
- Boot the kernel
- Perform audio playback
- Reboot the system via 'reboot' command
In many times the audio card cannot be probed, which causes playback to fail.
After restoring to the original i2c0 frequency of 100kHz there is no such
problem anymore.
This reverts commit 78b81f4666fbb22a20b1e63e5baf197ad2e90e88.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Fix a typo error, the "emi" names refer to the eim clocks.
The change fixes typo in EIM and EIM_SLOW pre-output dividers and
selectors clock names. Notably EIM_SLOW clock itself is named correctly.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
[vladimir_zapolskiy@mentor.com: ported to v3.17]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.rocketboards.org/linux-socfpga-next into fixes
Merge "SOCFPGA fixes for 3.18" from Dinh Nguyen:
These patches fixes an SMP and SDMMC driver hang during boot up on the
SOCFPGA platform.
Patch "arm: socfpga: fix fetching cpu1start_addr for SMP" fixes the SMP
trampoline code in order for CPU1 to correctly fetch it's cpu1start_addr.
Patch "ARM: dts: socfpga: rename gpio nodes" renames that GPIO node in order
to allow a standard way of specifying status="okay" in the board DTS file.
Patch "ARM: dts: socfpga: Fix SD card detect" fixes a SDMMC driver hang
during boot. The reason for the hang was the deferred probe of the SDMMC
driver was waiting for the GPIO resource that would never come.
Patch "ARM: dts: socfpga: Add a 3.3V fixed regulator node" adds a fixed
regulator node for the SDMMC driver to use.
* tag 'socfpga_fixes_for_3.18' of git://git.rocketboards.org/linux-socfpga-next:
ARM: dts: socfpga: Add a 3.3V fixed regulator node
ARM: dts: socfpga: Fix SD card detect
ARM: dts: socfpga: rename gpio nodes
arm: socfpga: fix fetching cpu1start_addr for SMP
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "at91: fixes for v3.18 #1" from Nicholas Ferre:
First AT91 fixes for 3.18:
- one more MAINTAINERS entry for the SSC driver
- a fix for the newly introduced power/reset driver
- a fix on at91sam9263 USB due to PLLB misconfiguration
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: fix PLLB frequencies
power: reset: at91-reset: fix power down register
MAINTAINERS: add atmel ssc driver maintainer entry
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
into fixes
Merge "Xilinx Zynq dt fixes for v3.18" from Michal Simek:
arm: Xilinx Zynq DT fixes for v3.18
- Fix gem register size
- Fix OPP
- Add missing references
- Trivial cleanup
* tag 'zynq-dt-fixes-for-3.18' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: DT: trivial: Fix mc node
ARM: zynq: DT: Add cadence watchdog node
ARM: zynq: DT: Add missing reference for memory-controller
ARM: zynq: DT: Add missing reference for ADC
ARM: zynq: DT: Add missing address for L2 pl310
ARM: zynq: DT: Remove 222 MHz OPP
ARM: zynq: DT: Fix GEM register area size
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allows booting from SD/MMC on RK3288 and other platforms. Added here so I
can enable the board in the boot farm.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
I missed in 9a2ad529ed26 that REGULATOR_FIXED_VOLTAGE had also gotten
deselected, so it needs to be added back as an explicit option.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Without the 3.3V regulator node, the SDMMC driver will give these warnings:
dw_mmc ff704000.dwmmc0: No vmmc regulator found
dw_mmc ff704000.dwmmc0: No vqmmc regulator found
This patch adds the regulator node, and points the SD/MMC to the regulator.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
---
v3: Rename nodes to have schematic-name_regulator and remove "boot-on" and
"always-on"
v2: Move the regulator nodes to their respective board dts file and
correctly rename them to match the schematic
|
|
Without this patch, the booting the SOCFPGA platform would hang at the
SDMMC driver loading. The issue, debugged by Doug Anderson, turned out
to be that the GPIO bank used by the SD card-detect was not set to
status="okay".
Also update the cd-gpios to point to portb of the &gpio1 GPIO IP.
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Use &gpio1 to set status="okay" and update cd-gpio=&portb
v3: Correctly degugged the issue to be a gpio node not having status="okay"
|
|
Since the Synopsys GPIO IP can support multiple ports of varying widths, it
would make more sense to have the GPIO node DTS entry as this:
gpio0: gpio@ff708000{
porta{
};
};
Also, this is documented in the snps-dwapb-gpio.txt.
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
|
|
PLLB input and output ranges were wrongly copied from at91sam9261 as the
datasheet didn't mention explicitly PLLB. Correct their values.
This fixes USB.
Reported-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
When CPU1 is brought out of reset, it's MMU is not turned on yet, so it will
only be able to use physical addresses. For systems with that have the
MMU page configured for 0xC0000000, 0x80000000, or 0x40000000
"BIC 0x40000000" will work just fine, as it was just converting the
virtual address of &cpu1start_addr into a physical address, ie. 0xC0000000
became 0x80000000. So for systems where the SDRAM controller was able to do a
wrap-around access, this was working fine, as it was just dropping the MSB,
but for systems where out of bounds memory access is not allowed, this would
not allow CPU1 to correctly fetch &cpu1start_addr.
This patch fixes the secondary_trampoline code to correctly fetch the
physical address of cpu1start_addr directly. The patch will subtract the
correct PAGE_OFFSET from &cpu1start_addr. And since on this platform, the
physical memory will always start at 0x0, subtracting PAGE_OFFSET from
&cpu1start_addr will allow CPU1 to correctly fetch the value of cpu1start_addr.
While at it, change the name of cpu1start_addr to socfpga_cpu1start_addr
to avoid any future naming collisions for multiplatform image.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v4: Updated commit log to correctly lay out the usage of PAGE_OFFSET and
add comments to the same effect.
v3: Used PAGE_OFFSET to get the physical address
v2: Correctly get the physical address instead of just a BIC hack.
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox framework from Jassi Brar:
"A framework for Mailbox controllers and clients have been cooking for
more than a year now.
Everybody in the CC list had been copied on patchset revisions and
most of them have made sounds of approval, though just one concrete
Reviewed-by. The patchset has also been in linux-next for a couple of
weeks now and no conflict has been reported. The framework has the
backing of at least 5 platforms, though I can't say if/when they
upstream their drivers (some businesses have 'changed')"
(Further acked-by by Arnd Bergmann and Suman Anna in the pull request
thread)
* 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt: mailbox: add generic bindings
doc: add documentation for mailbox framework
mailbox: Introduce framework for mailbox
mailbox: rename pl320-ipc specific mailbox.h
|
|
Update the multi_v7_defconfig enabling the watchdog driver for Meson
SoCs.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
sed -i 's/}\ ;/};/g'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add the cadence watchdog node to the Zynq devicetree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add missing reference for memory-controller.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add missing reference for ADC node.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
By in sync with others node and add also baseaddr
to the node name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The size of the GEM's register area is only 0x1000 bytes.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
|
|
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
Pull second batch of changes for KVM/{arm,arm64} from Marc Zyngier:
"The most obvious thing is the sizeable MMU changes to support 48bit
VAs on arm64.
Summary:
- support for 48bit IPA and VA (EL2)
- a number of fixes for devices mapped into guests
- yet another VGIC fix for BE
- a fix for CPU hotplug
- a few compile fixes (disabled VGIC, strict mm checks)"
[ I'm pulling directly from Marc at the request of Paolo Bonzini, whose
backpack was stolen at Düsseldorf airport and will do new keys and
rebuild his web of trust. - Linus ]
* tag 'kvm-arm-for-3.18-take-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm:
arm/arm64: KVM: Fix BE accesses to GICv2 EISR and ELRSR regs
arm: kvm: STRICT_MM_TYPECHECKS fix for user_mem_abort
arm/arm64: KVM: Ensure memslots are within KVM_PHYS_SIZE
arm64: KVM: Implement 48 VA support for KVM EL2 and Stage-2
arm/arm64: KVM: map MMIO regions at creation time
arm64: kvm: define PAGE_S2_DEVICE as read-only by default
ARM: kvm: define PAGE_S2_DEVICE as read-only by default
arm/arm64: KVM: add 'writable' parameter to kvm_phys_addr_ioremap
arm/arm64: KVM: fix potential NULL dereference in user_mem_abort()
arm/arm64: KVM: use __GFP_ZERO not memset() to get zeroed pages
ARM: KVM: fix vgic-disabled build
arm: kvm: fix CPU hotplug
|
|
Pull MTD update from Brian Norris:
"Sorry for delaying this a bit later than usual. There's one mild
regression from 3.16 that was noticed during the 3.17 cycle, and I
meant to send a fix for it along with this pull request. I'll
probably try to queue it up for a later pull request once I've had a
better look at it, hopefully by -rc2 at the latest.
Summary for this pull:
NAND
- Cleanup for Denali driver
- Atmel: add support for new page sizes
- Atmel: fix up 'raw' mode support
- Atmel: miscellaneous cleanups
- New timing mode helpers for non-ONFI NAND
- OMAP: allow driver to be (properly) built as a module
- bcm47xx: RESET support and other cleanups
SPI NOR
- Miscellaneous cleanups, to prepare framework for wider use (some
further work still pending)
- Compile-time configuration to select 4K vs. 64K support for flash
that support both (necessary for using UBIFS on some SPI NOR)
A few scattered code quality fixes, detected by Coverity
See the changesets for more"
* tag 'for-linus-20141015' of git://git.infradead.org/linux-mtd: (59 commits)
mtd: nand: omap: Correct CONFIG_MTD_NAND_OMAP_BCH help message
mtd: nand: Force omap_elm to be built as a module if omap2_nand is a module
mtd: move support for struct flash_platform_data into m25p80
mtd: spi-nor: add Kconfig option to disable 4K sectors
mtd: nand: Move ELM driver and rename as omap_elm
nand: omap2: Replace pr_err with dev_err
nand: omap2: Remove horrible ifdefs to fix module probe
mtd: nand: add Hynix's H27UCG8T2ATR-BC to nand_ids table
mtd: nand: support ONFI timing mode retrieval for non-ONFI NANDs
mtd: physmap_of: Add non-obsolete map_rom probe
mtd: physmap_of: Fix ROM support via OF
MAINTAINERS: add l2-mtd.git, 'next' tree for MTD
mtd: denali: fix indents and other trivial things
mtd: denali: remove unnecessary parentheses
mtd: denali: remove another set-but-unused variable
mtd: denali: fix include guard and license block of denali.h
mtd: nand: don't break long print messages
mtd: bcm47xxnflash: replace some magic numbers
mtd: bcm47xxnflash: NAND_CMD_RESET support
mtd: bcm47xxnflash: add cmd_ctrl handler
...
|
|
Explicitly set the dr_mode for the second dwc3 controller on the
Arndale Octa board to host mode. This is required to ensure the
controller is initialized in the right mode if the kernel is build
with USB gadget support.
Reported-By: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The EIRSR and ELRSR registers are 32-bit registers on GICv2, and we
store these as an array of two such registers on the vgic vcpu struct.
However, we access them as a single 64-bit value or as a bitmap pointer
in the generic vgic code, which breaks BE support.
Instead, store them as u64 values on the vgic structure and do the
word-swapping in the assembly code, which already handles the byte order
for BE systems.
Tested-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
CM-QS600 is a APQ8064 based computer on module.
The details are available at
http://compulab.co.il/products/computer-on-modules/cm-qs600/
Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
|
This DTS has support for the Sony Xperia Z1 phone (codenamed Honami).
This first version of the DTS supports just a serial console.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
|
Add SATA PHY and SATA AHCI controller nodes to device tree to enable
generic ahci support on the IPQ8064/AP148 board.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
|
|
Commit:
b886576 ARM: KVM: user_mem_abort: support stage 2 MMIO page mapping
introduced some code in user_mem_abort that failed to compile if
STRICT_MM_TYPECHECKS was enabled.
This patch fixes up the failing comparison.
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung defconfig, actually exynos_defconig updates for v3.18" from
Kukjin Kim:
- enable USB gadget support
- enable Maxim77802 support
- enable Maxim77693 and I2C GPIO drivers
- enable Atmel maXTouch support
- enable SBS battery support
- enable Control Groups support
* tag 'samsung-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v3.18" from Kukjin Kim:
- fix ifdef around cpu_*_do_[suspend, resume] ops to check
CONFIG_ARM_CPU_SUSPEND and not CONFIG_PM_SLEEP
- fix exynos_defconfig build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
- fix enabling Samsung PM debug functionality due to recently merged
patches and previous merge conflicts
- fix pull-up setting in sd4_width8 pin group for exynos4x12
* tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Two omap fixes for v3.18 merge window" from Tony Lindgren:
Two omap fixes for issues noticed during the merge window:
- We need to enable ARM errata 430973 for omap3
- The smc91x on some early n900 boards need to be disabled
for now until the dependencies to specific a bootloader
version are fixed
* tag 'fixes-for-v3.18-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 97a13e5289ba ('net: phy: mdio-sun4i: don't select REGULATOR') removed
the select of REGULATOR, which means that it now has to be explicitly
enabled in the defconfig or things won't work very well.
In particular, this fixes a problem with SD/MMC not probing on my A31-based
board.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock tree updates from Mike Turquette:
"The clk tree changes for 3.18 are dominated by clock drivers. Mostly
fixes and enhancements to existing drivers as well as new drivers.
This tag contains a bit more arch code than I usually take due to some
OMAP2+ changes. Additionally it contains the restart notifier
handlers which are merged as a dependency into several trees.
The PXA changes are the only messy part. Due to having a stable tree
I had to revert one patch and follow up with one more fix near the tip
of this tag. Some dead code is introduced but it will soon become
live code after 3.18-rc1 is released as the rest of the PXA family is
converted over to the common clock framework.
Another trend in this tag is that multiple vendors have started to
push the complexity of changing their CPU frequency into the clock
driver, whereas this used to be done in CPUfreq drivers.
Changes to the clk core include a generic gpio-clock type and a
clk_set_phase() function added to the top-level clk.h api. Due to
some confusion on the fbdev mailing list the kernel boot parameters
documentation was updated to further explain the clk_ignore_unused
parameter, which is often required by users of the simplefb driver.
Finally some fixes to the locking around the clock debugfs stuff was
done to prevent deadlocks when interacting with other subsystems."
* tag 'clk-for-linus-3.18' of git://git.linaro.org/people/mike.turquette/linux: (99 commits)
clk: pxa clocks build system fix
Revert "arm: pxa: Transition pxa27x to clk framework"
clk: samsung: register restart handlers for s3c2412 and s3c2443
clk: rockchip: add restart handler
clk: rockchip: rk3288: i2s_frac adds flag to set parent's rate
doc/kernel-parameters.txt: clarify clk_ignore_unused
arm: pxa: Transition pxa27x to clk framework
dts: add devicetree bindings for pxa27x clocks
clk: add pxa27x clock drivers
arm: pxa: add clock pll selection bits
clk: dts: document pxa clock binding
clk: add pxa clocks infrastructure
clk: gpio-gate: Ensure gpiod_ APIs are prototyped
clk: ti: dra7-atl-clock: Mark the device as pm_runtime_irq_safe
clk: ti: LLVMLinux: Move __init outside of type definition
clk: ti: consider the fact that of_clk_get() might return an error
clk: ti: dra7-atl-clock: fix a memory leak
clk: ti: change clock init to use generic of_clk_init
clk: hix5hd2: add I2C clocks
clk: hix5hd2: add watchdog0 clocks
...
|
|
When creating or moving a memslot, make sure the IPA space is within the
addressable range of the guest. Otherwise, user space can create too
large a memslot and KVM would try to access potentially unallocated page
table entries when inserting entries in the Stage-2 page tables.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
This patch adds the necessary support for all host kernel PGSIZE and
VA_SPACE configuration options for both EL2 and the Stage-2 page tables.
However, for 40bit and 42bit PARange systems, the architecture mandates
that VTCR_EL2.SL0 is maximum 1, resulting in fewer levels of stage-2
pagge tables than levels of host kernel page tables. At the same time,
systems with a PARange > 42bit, we limit the IPA range by always setting
VTCR_EL2.T0SZ to 24.
To solve the situation with different levels of page tables for Stage-2
translation than the host kernel page tables, we allocate a dummy PGD
with pointers to our actual inital level Stage-2 page table, in order
for us to reuse the kernel pgtable manipulation primitives. Reproducing
all these in KVM does not look pretty and unnecessarily complicates the
32-bit side.
Systems with a PARange < 40bits are not yet supported.
[ I have reworked this patch from its original form submitted by
Jungseok to take the architecture constraints into consideration.
There were too many changes from the original patch for me to
preserve the authorship. Thanks to Catalin Marinas for his help in
figuring out a good solution to this challenge. I have also fixed
various bugs and missing error code handling from the original
patch. - Christoffer ]
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild changes from Michal Marek:
- fix for handling dependencies of *-objs targets by Masahiro Yamada
- lots of cleanups in the kbuild machinery, also by Masahiro
- fixes for the kconfig build to use an UTF-8 capable ncurses library
if possible and to build on not-so-standard installs
- some more minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Do not reference *-n variables in the Makefile
kbuild: simplify build, clean, modbuiltin shorthands
kbuild: arm: Do not define "comma" twice
kbuild: remove obj-n and lib-n handling
kbuild: remove unnecessary variable initializaions
kbuild: remove unnecessary "obj- := dummy.o" trick
kbuild: handle C=... and M=... after entering into build directory
kbuild: use $(Q) for sub-make target
kbuild: fake the "Entering directory ..." message more simply
kconfig/lxdialog: get ncurses CFLAGS with pkg-config
kconfig: nconfig: fix multi-byte UTF handling
kconfig: lxdialog: fix spelling
kbuild: Make scripts executable
kbuild: remove redundant clean-files from scripts/kconfig/Makefile
kbuild: refactor script/kconfig/Makefile
kbuild: handle the dependency of multi-objs hostprogs appropriately
kbuild: handle multi-objs dependency appropriately
|
|
Merge second patch-bomb from Andrew Morton:
- a few hotfixes
- drivers/dma updates
- MAINTAINERS updates
- Quite a lot of lib/ updates
- checkpatch updates
- binfmt updates
- autofs4
- drivers/rtc/
- various small tweaks to less used filesystems
- ipc/ updates
- kernel/watchdog.c changes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm: softdirty: enable write notifications on VMAs after VM_SOFTDIRTY cleared
kernel/param: consolidate __{start,stop}___param[] in <linux/moduleparam.h>
ia64: remove duplicate declarations of __per_cpu_start[] and __per_cpu_end[]
frv: remove unused declarations of __start___ex_table and __stop___ex_table
kvm: ensure hard lockup detection is disabled by default
kernel/watchdog.c: control hard lockup detection default
staging: rtl8192u: use %*pEn to escape buffer
staging: rtl8192e: use %*pEn to escape buffer
staging: wlan-ng: use %*pEhp to print SN
lib80211: remove unused print_ssid()
wireless: hostap: proc: print properly escaped SSID
wireless: ipw2x00: print SSID via %*pE
wireless: libertas: print esaped string via %*pE
lib/vsprintf: add %*pE[achnops] format specifier
lib / string_helpers: introduce string_escape_mem()
lib / string_helpers: refactoring the test suite
lib / string_helpers: move documentation to c-file
include/linux: remove strict_strto* definitions
arch/x86/mm/numa.c: fix boot failure when all nodes are hotpluggable
fs: check bh blocknr earlier when searching lru
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 seccomp changes from Ingo Molnar:
"This tree includes x86 seccomp filter speedups and related preparatory
work, which touches core seccomp facilities as well.
The main idea is to split seccomp into two phases, to be able to enter
a simple fast path for syscalls with ptrace side effects.
There's no substantial user-visible (and ABI) effects expected from
this, except a change in how we emit a better audit record for
SECCOMP_RET_TRACE events"
* 'x86-seccomp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64, entry: Use split-phase syscall_trace_enter for 64-bit syscalls
x86_64, entry: Treat regs->ax the same in fastpath and slowpath syscalls
x86: Split syscall_trace_enter into two phases
x86, entry: Only call user_exit if TIF_NOHZ
x86, x32, audit: Fix x32's AUDIT_ARCH wrt audit
seccomp: Document two-phase seccomp and arch-provided seccomp_data
seccomp: Allow arch code to provide seccomp_data
seccomp: Refactor the filter callback and the API
seccomp,x86,arm,mips,s390: Remove nr parameter from secure_computing
|
|
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix wrong compatible string of Exynos3250 RTC (Real-Time Clock) dt node.
The RTC of Exynos3250 must need additional source clock (XrtcXTI).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
