| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 8d545f32bd77 ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 1b53e3416dd0 ("ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add the three leds on the sama5d2 Xplained board with their pinctrl node.
The blue led is positioned with the "heartbeat" trigger.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: add commit message and adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add the push button named "PB USER" with code 0x104. Associated pinctrl node is
also added.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
For USB gadget on port A (device mode):
- pin PA31 is configured as an input GPIO which triggers an interrupt when
vbus is detected on USB port A.
- pin PB9 is configured as an output GPIO and set to low level so the
board doesn't supply vbus to USB port A.
For USB host:
- pin PB10 is configured as an output GPIO and is active at high level.
The ohci driver will activate this pin so the board supplies vbus to USB
port B.
- pin PB9 should be configured as an output GPIO and active at high level
to use to USB port A in host mode (conflicts with USB gadget).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Both nodes are required to access NAND Flash memory. Additional
settings will be necessary at the board level to use it.
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
All pinctrl nodes for the Atmel pinctrl controller need to have their
bias configuration explicitly defined. Otherwise, the pinctrl mapping
is not valid.
It works for now as the pinctrl driver proceeds even with invalid
mappings, but this can become an issue, if the pinctrl driver starts
to require valid mappings. Additionally, the pin is not protected from
being remapped later by an other driver.
There is an external 1kOhms pull-up to 3.3V, so no bias is required on
the Ethernet PHY's interrupt line.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The watchdog timer on the SoCFPGA platform is the Synopsys Designware watchdog.
Enable CONFIG_DW_WATCHDOG for the driver to get built.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu fixes for 4.5 (part 1)
- Fix dts on buffalo linksations machines (gpios and leds)
- Fix dts partition node according to new binding introduced in v4.5
* tag 'mvebu-fixes-4.5-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: orion5x: gpio pin fixes for linkstation lswtgl
ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wvl/vl
ARM: dts: kirkwood: gpio-leds fixes for linkstation ls-wxl/wsxl
ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wvl/vl
ARM: dts: kirkwood: gpio pin fixes for linkstation ls-wxl/wsxl
ARM: mvebu: ix4-300d: Add compatible property to "partitions" node
ARM: mvebu: kirkwood: Add compatible property to "partitions" node
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
First fixes for 4.5. Only DT changes:
- sama5d4: error in DBGU index
- addition of phy properties in several boards
- at91sam9n12ek fix a panel compatible string
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
ARM: dts: at91: sama5d4 xplained: properly mux phy interrupt
ARM: dts: at91: sama5d4ek: add phy address and IRQ for macb0
ARM: dts: at91: sama5d2 xplained: add phy address and IRQ for macb0
ARM: dts: at91: at91sam9n12ek: fix panel compatible string
ARM: dts: at91: sama5d4: fix instance id of DBGU
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This platform recently moved to multi-platform, so missed the global
fixup by commit e32465429490 ("ARM: use "depends on" for SoC configs
instead of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This platform was recently added, so missed the global fixup by
commit e32465429490 ("ARM: use "depends on" for SoC configs instead
of "if" after prompt"). Fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This newly added code missed the global fixup by commit 75305275a721
("ARM: use const and __initconst for smp_operations"). So fix it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This newly added code missed the global fixup by commit 75305275a721
("ARM: use const and __initconst for smp_operations"). So fix it now.
Also, add missing "static" qualifier.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add the copy_file_range() syscall to ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Update Eth PHY settings to make it possible to run both phys at 1Gbps.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix CPSW EMAC pinmux
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix UART3 pinmux.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On-board SPI flash cat act at 48Mhz SPI bus frequency.
Update the DT frequency property.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Setup USB2 to act in "HOST" mode by default.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix SB-SOM EEPROM I2C address
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Revert commit 7cd6ca770d1b ("ARM: dts: Change I2C2 and I2C3 to 400KHz
for LogicPD Torpedo DM3730 devkit") It was already done and it is
just a duplicate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Now IRQs for Pixcir Tangoc touchscreen are defined using
IRQ_TYPE_NONE in am437x-gp-evm.dts and am43x-epos-evm.dts wich
do not correspond HW.
Hence, update am437x-gp-evm.dts and am43x-epos-evm.dts files
and use correct flag IRQ_TYPE_EDGE_FALLING for irq types.
While here, remove duplicated irq declaration for pixcir_ts@5c node
in am437x-gp-evm.dts.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
PPI(2) ID29 - twd interrupt is rising-edge sensitive.
and the same is proved by GIC distributor register value
GIC_DIST_CONFIG(0xC04) = 0x7DC00000.
Hence, set IRQ triggering type to IRQ_TYPE_EDGE_RISING
for ARM TWD and Global timers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of
"edge falling".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
|
|
No interrupt were received from the phy because PIOE 1 may not be properly
muxed. It prevented proper link detection, especially since commit
321beec5047a ("net: phy: Use interrupts when available in NOLINK state")
disables polling.
Cc: <stable@vger.kernel.org> # 4.4
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
On SAMA5D4EK board, the Ethernet doesn't work after resuming from the suspend
state.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
After 57a38effa598 (net: phy: micrel: disable broadcast for KSZ8081/KSZ8091)
the macb0 interface has difficulties to come back from power saving mode if
address not explicitly set up.
As the micrel phy on the board is actually configured to show up at address 1
we use this explicitly.
Adding the phy node and its real address fixes the issue.
The phy IRQ and associated pinmux node is also added.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: stable@vger.kernel.org # 4.4+ // manual merge needed
|
|
Properly use qiaodian as the vendor prefix for the panel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Change instance id of DBGU to 45.
Signed-off-by: Mohamed Jamsheeth Hajanajubudeen <mohamedjamsheeth.hajanajubudeen@atmel.com>
Fixes: 7c661394c56c ("ARM: at91: dt: add device tree file for SAMA5D4 SoC")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Building with CONFIG_CC_STACKPROTECTOR_STRONG triggers protection code
generation under CONFIG_ARM_ATAG_DTB_COMPAT but this is too early for
being able to use any of the stack_chk code. Explicitly disable it for
only the atags_to_fdt bits.
Suggested-by: zhxihu <zhxihu@marvell.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The tcxo-clock-frequency binding is listed as optional,
but without it the wl12xx used on the torpedo + wireless
may hang. Scanning also appears broken without this patch.
Signed-off-by: Adam Ford <aford173@gmail.com>
Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD
Torpedo DM3730 devkit")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
In order to set the currently platform dependent dmtimer
functions pointers as platform data for the pwm-omap-dmtimer
platform driver, add it to plat-omap auxdata_lookup table.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Here're a few gpio pin related fixes:
- remove pinctrl-0 definition from pinctrl, since those pins are used
in other places such as gpio-fan and regulators.
- keep initial state of power led
- fix for alarm pin of gpio-fan.
Fixes: dc57844a736f ("ARM: dts: orion5x: add buffalo linkstation ls-wtgl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The GPIOs controlling the LEDs, listed below, are active high, not low:
- gpio-leds: "lswvl:red:alarm" pin
- gpio-leds: "lswvl:red:func" pin
- gpio-leds: "lswvl:amber:info" pin
- gpio-leds: "lswvl:blue:func" pin
- gpio-leds: "lswvl:red:hdderr{0,1}" pin
Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The GPIOs controlling the LEDs, listed below, are active high, not low:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr{0,1}" pin
Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: c43379e150aa ("ARM: dts: add buffalo linkstation ls-wvl/vl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
For kirkwood, gpio pins starts from 32 are in the 2nd bank, so it should be
converted to "gpio1 <pin minus 32>" in dts file.
e.g. gpio 40 should be "gpio1 8"
Besides, a few other pin fixes for ls-wxl/wsxl, to match with mpp pin
definition:
- gpio-leds: "lswxl:blue:power" pin
- gpio-leds: "lswxl:red:func" pin
- gpio-leds: "lswxl:red:hdderr0" pin
- gpio-leds: "lswxl:red:hdderr1" pin
- gpio-fan: low/high/alarm pin
The pin/bank issue was found when discussing Debian Bug #810894
[https://bugs.debian.org/810894#47]
Fixes: e54e4b1b622e ("ARM: dts: add buffalo linkstation ls-wxl/wsxl")
Reported-by: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
As of commit e488ca9f8d4f62c2 ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Merge small final update from Andrew Morton:
- DAX feature work: add fsync/msync support
- kfree cleanup, MAINTAINERS update
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: return arch/sh to maintained state, with new maintainers
tree wide: use kvfree() than conditional kfree()/vfree()
dax: never rely on bh.b_dev being set by get_block()
xfs: call dax_pfn_mkwrite() for DAX fsync/msync
ext4: call dax_pfn_mkwrite() for DAX fsync/msync
ext2: call dax_pfn_mkwrite() for DAX fsync/msync
dax: add support for fsync/sync
mm: add find_get_entries_tag()
dax: support dirty DAX entries in radix tree
pmem: add wb_cache_pmem() to the PMEM API
dax: fix conversion of holes to PMDs
dax: fix NULL pointer dereference in __dax_dbg()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC support for Tegra platforms from Olof Johansson:
"Here's a single-SoC topic branch that we've staged separately. Mainly
because it was hard to sort the branch contents in a way that fit our
existing branches due to some refactorings.
The code has been in -next for quite a while, but we staged it in
arm-soc a bit late, which is why we've kept it separate from the other
updates and are sending it separately here"
* tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support
arm64: tegra: Add NVIDIA P2597 I/O board support
arm64: tegra: Add NVIDIA Jetson TX1 support
arm64: tegra: Add NVIDIA P2571 board support
arm64: tegra: Add NVIDIA P2371 board support
arm64: tegra: Add NVIDIA P2595 I/O board support
arm64: tegra: Add NVIDIA P2530 main board support
arm64: tegra: Add Tegra210 support
arm64: tegra: Add NVIDIA Tegra132 Norrin support
arm64: tegra: Add Tegra132 support
ARM: tegra: select USB_ULPI from EHCI rather than platform
ARM: tegra: Ensure entire dcache is flushed on entering LP0/1
amba: Hide TEGRA_AHB symbol
soc/tegra: Add Tegra210 support
soc/tegra: Provide per-SoC Kconfig symbols
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
|
|
There are many locations that do
if (memory_was_allocated_by_vmalloc)
vfree(ptr);
else
kfree(ptr);
but kvfree() can handle both kmalloc()ed memory and vmalloc()ed memory
using is_vmalloc_addr(). Unless callers have special reasons, we can
replace this branch with kvfree(). Please check and reply if you found
problems.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Boris Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.5
Correct extal1 frequency of armadillo800eva board
* tag 'renesas-fixes-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can
now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that
DEBUG_RODATA gets selected by default. This way we can make sure
any related issues are caught early.
And while testing things on various devices, I noticed we're
missing few loadable modules to make things more usable:
- USB Ethernet for smsc75xx, we only have smsc97xx right now
- Basic USB serial drivers for things like ftdi and pl2303 ports
- Blinking leds with pca963x
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
