Age | Commit message (Collapse) | Author | Files | Lines |
|
[ Upstream commit 78ab3d352f2982bf3f7e506bfbaba7afee1ed8a9 ]
GPIOs controlling backlight on Spitz and Akita are coming from GPIO
expanders, not the pxa27xx-gpio block, correct it.
Additionally GPIO lookup tables operate with pin numbers rather than
legacy GPIO numbers, fix that as well. Use raw numbers instead of legacy
GPIO names to avoid confusion.
Fixes: ee0c8e494cc3 ("backlight: corgi: Convert to use GPIO descriptors")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20240628180852.1738922-2-dmitry.torokhov@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit df35c6e9027cf9affe699e632a48082ab1bbba4c ]
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0df3c7d7a73d75153090637392c0b73a63cdc24a ]
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 24d3ba0a7b44c1617c27f5045eecc4f34752ab03 upstream.
The 32-bit ARM kernel stops working if the kernel grows to the point
where veneers for __get_user_* are created.
AAPCS32 [1] states, "Register r12 (IP) may be used by a linker as a
scratch register between a routine and any subroutine it calls. It
can also be used within a routine to hold intermediate values between
subroutine calls."
However, bl instructions buried within the inline asm are unpredictable
for compilers; hence, "ip" must be added to the clobber list.
This becomes critical when veneers for __get_user_* are created because
veneers use the ip register since commit 02e541db0540 ("ARM: 8323/1:
force linker to use PIC veneers").
[1]: https://github.com/ARM-software/abi-aa/blob/2023Q1/aapcs32/aapcs32.rst
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: John Stultz <jstultz@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit acc3815db1a02d654fbc19726ceaadca0d7dd81c ]
Replace a comma between expression statements by a semicolon.
Fixes: efc1bb8a6fd5 ("davinci: add power management support")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cca46f811d0000c1522a5e18ea48c27a15e45c05 ]
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc78062477 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ac4c1d794e7ff454d191bbdab7585ed8dbf3758 ]
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-smdk4412.dtb: keypad@100a0000: 'key-A', 'key-B', 'key-C', 'key-D', 'key-E', 'linux,keypad-no-autorepeat' do not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: c9b92dd70107 ("ARM: dts: Add keypad entries to SMDK4412")
Link: https://lore.kernel.org/r/20240312183105.715735-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 88208d3cd79821117fd3fb80d9bcab618467d37b ]
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4412-origen.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: bd08f6277e44 ("ARM: dts: Add keypad entries to Exynos4412 based Origen")
Link: https://lore.kernel.org/r/20240312183105.715735-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 87d8e522d6f5a004f0aa06c0def302df65aff296 ]
Although the Samsung SoC keypad binding defined
linux,keypad-no-autorepeat property, Linux driver never implemented it
and always used linux,input-no-autorepeat. Correct the DTS to use
property actually implemented.
This also fixes dtbs_check errors like:
exynos4210-smdkv310.dtb: keypad@100a0000: 'linux,keypad-no-autorepeat' does not match any of the regexes: '^key-[0-9a-z]+$', 'pinctrl-[0-9]+'
Cc: <stable@vger.kernel.org>
Fixes: 0561ceabd0f1 ("ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN")
Link: https://lore.kernel.org/r/20240312183105.715735-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit deff401b14e2d832b25b55862ad6c73378fe034e ]
Commit 4fc8cb47fcfd ("drm/display: Move HDMI helpers into display-helper
module") turned the DRM_DW_HDMI dependency of DRM_SUN8I_DW_HDMI into a
depends on which ended up disabling the driver in the defconfig. Make
sure it's still enabled.
Fixes: 4fc8cb47fcfd ("drm/display: Move HDMI helpers into display-helper module")
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240403-fix-dw-hdmi-kconfig-v1-5-afbc4a835c38@kernel.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c4238686f9093b98bd6245a348bcf059cdce23af ]
We found below OOB crash:
[ 33.452494] ==================================================================
[ 33.453513] BUG: KASAN: stack-out-of-bounds in refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec
[ 33.454660] Write of size 164 at addr c1d03d30 by task swapper/0/0
[ 33.455515]
[ 33.455767] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 6.1.25-mainline #1
[ 33.456880] Hardware name: Generic DT based system
[ 33.457555] unwind_backtrace from show_stack+0x18/0x1c
[ 33.458326] show_stack from dump_stack_lvl+0x40/0x4c
[ 33.459072] dump_stack_lvl from print_report+0x158/0x4a4
[ 33.459863] print_report from kasan_report+0x9c/0x148
[ 33.460616] kasan_report from kasan_check_range+0x94/0x1a0
[ 33.461424] kasan_check_range from memset+0x20/0x3c
[ 33.462157] memset from refresh_cpu_vm_stats.constprop.0+0xcc/0x2ec
[ 33.463064] refresh_cpu_vm_stats.constprop.0 from tick_nohz_idle_stop_tick+0x180/0x53c
[ 33.464181] tick_nohz_idle_stop_tick from do_idle+0x264/0x354
[ 33.465029] do_idle from cpu_startup_entry+0x20/0x24
[ 33.465769] cpu_startup_entry from rest_init+0xf0/0xf4
[ 33.466528] rest_init from arch_post_acpi_subsys_init+0x0/0x18
[ 33.467397]
[ 33.467644] The buggy address belongs to stack of task swapper/0/0
[ 33.468493] and is located at offset 112 in frame:
[ 33.469172] refresh_cpu_vm_stats.constprop.0+0x0/0x2ec
[ 33.469917]
[ 33.470165] This frame has 2 objects:
[ 33.470696] [32, 76) 'global_zone_diff'
[ 33.470729] [112, 276) 'global_node_diff'
[ 33.471294]
[ 33.472095] The buggy address belongs to the physical page:
[ 33.472862] page:3cd72da8 refcount:1 mapcount:0 mapping:00000000 index:0x0 pfn:0x41d03
[ 33.473944] flags: 0x1000(reserved|zone=0)
[ 33.474565] raw: 00001000 ed741470 ed741470 00000000 00000000 00000000 ffffffff 00000001
[ 33.475656] raw: 00000000
[ 33.476050] page dumped because: kasan: bad access detected
[ 33.476816]
[ 33.477061] Memory state around the buggy address:
[ 33.477732] c1d03c00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.478630] c1d03c80: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 00
[ 33.479526] >c1d03d00: 00 04 f2 f2 f2 f2 00 00 00 00 00 00 f1 f1 f1 f1
[ 33.480415] ^
[ 33.481195] c1d03d80: 00 00 00 00 00 00 00 00 00 00 04 f3 f3 f3 f3 f3
[ 33.482088] c1d03e00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
[ 33.482978] ==================================================================
We find the root cause of this OOB is that arm does not clear stale stack
poison in the case of cpuidle.
This patch refer to arch/arm64/kernel/sleep.S to resolve this issue.
From cited commit [1] that explain the problem
Functions which the compiler has instrumented for KASAN place poison on
the stack shadow upon entry and remove this poison prior to returning.
In the case of cpuidle, CPUs exit the kernel a number of levels deep in
C code. Any instrumented functions on this critical path will leave
portions of the stack shadow poisoned.
If CPUs lose context and return to the kernel via a cold path, we
restore a prior context saved in __cpu_suspend_enter are forgotten, and
we never remove the poison they placed in the stack shadow area by
functions calls between this and the actual exit of the kernel.
Thus, (depending on stackframe layout) subsequent calls to instrumented
functions may hit this stale poison, resulting in (spurious) KASAN
splats to the console.
To avoid this, clear any stale poison from the idle thread for a CPU
prior to bringing a CPU online.
From cited commit [2]
Extend to check for CONFIG_KASAN_STACK
[1] commit 0d97e6d8024c ("arm64: kasan: clear stale stack poison")
[2] commit d56a9ef84bd0 ("kasan, arm64: unpoison stack only with CONFIG_KASAN_STACK")
Signed-off-by: Boy Wu <boy.wu@mediatek.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 5615f69bc209 ("ARM: 9016/2: Initialize the mapping of KASan shadow memory")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
the valid property
[ Upstream commit e027b71762e84ee9d4ba9ad5401b956b9e83ed2a ]
By checking the pmic node with microchip,mcp16502.yaml#
'regulator-suspend-voltage' does not match any of the
regexes 'pinctrl-[0-9]+' from schema microchip,mcp16502.yaml#
which inherits regulator.yaml#. So replace regulator-suspend-voltage
with regulator-suspend-microvolt to avoid the inconsitency.
Fixes: 85b1304b9daa ("ARM: dts: at91: sama7g5ek: set regulator voltages for standby state")
Signed-off-by: Andrei Simion <andrei.simion@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20240404123824.19182-2-andrei.simion@microchip.com
[claudiu.beznea: added a dot before starting the last sentence in commit
description]
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
This reverts commit 0f4048e1a0c6e9d3d31ce5b684600fd137cebfca which is
commit 319e6ac143b9e9048e527ab9dd2aabb8fdf3d60f upstream.
It breaks the 6.1.y build, so needs to be reverted.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 319e6ac143b9e9048e527ab9dd2aabb8fdf3d60f ]
The Pandora uses GPIO descriptors pretty much exclusively, but not
for ASoC, so let's fix it. Register the pins in a descriptor table
in the machine since the ASoC device is not using device tree.
Use static locals for the GPIO descriptors because I'm not able
to experient with better state storage on any real hardware. Others
using the Pandora can come afterwards and improve this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Link: https://lore.kernel.org/r/20230926-descriptors-asoc-ti-v1-4-60cf4f8adbc5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit faf3b5cb59f84e4056bd84f115a958bc99c61e65 ]
As of 0426370b58b2 ("ARM: dts: omap2420-n810: Correct the audio codec
(tlv320aic33) node") the DTS properly specifies reset GPIO, and the
device name in auxdata lookup table does not even match the one in
device tree anymore, so stop instantiating it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20221102232004.1721864-1-dmitry.torokhov@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 831e0cd4f9ee15a4f02ae10b67e7fdc10eb2b4fc ]
Fix an obvious spelling error in the PMIC compatible in the MMP2
Brownstone DTS file.
Fixes: 58f1193e6210 ("mfd: max8925: Add dts")
Cc: <stable@vger.kernel.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Closes: https://lore.kernel.org/linux-devicetree/1410884282-18041-1-git-send-email-k.kozlowski@samsung.com/
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125-brownstone-typo-fix-v2-1-45bc48a0c81c@skole.hr
[krzysztof: Just 10 years to take a patch, not bad! Rephrased commit
msg]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 53cc9baeb9bc2a187eb9c9790d30995148852b12 ]
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON")
Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 023bd910d3ab735459f84b22bb99fb9e00bd9d76 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7da7b84fee58c85a6075022023d31edea40e81a1 ]
Drop the phy-reset-duration and phy-reset-gpios deprecated properties and
move reset-gpios under the switch node.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stable-dep-of: 023bd910d3ab ("ARM: dts: imx6dl-yapp4: Fix typo in the QCA switch register address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3baa4c5143d65ebab2de0d99a395e5f4f1f46608 ]
When the development chip ROM was added, the "direct-mapped" compatible
value was already obsolete. In addition, the device node lacked the
accompanying "probe-type" property, causing the old physmap_of_core
driver to fall back to trying all available probe types.
Unfortunately this fallback was lost when the DT and pdata cases were
merged.
Fix this by using the modern "mtd-rom" compatible value instead.
Fixes: 5c3f5edbe0a1dff3 ("ARM: realview: add flash devices to the PB1176 DTS")
Fixes: 642b1e8dbed7bbbf ("mtd: maps: Merge physmap_of.c into physmap-core.c")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 724c4bf0e4bf81dba77736afb93964c986c3c123 ]
The qfprom actually is bigger than 0x1000, so adjust the reg.
Note that the non-ECC-corrected qfprom can be found at 0xfc4b8000
(-0x4000). The current reg points to the ECC-corrected qfprom block
which should have equivalent values at all offsets compared to the
non-corrected version.
[luca@z3ntu.xyz: extract to standalone patch and adjust for review
comments]
Fixes: c59ffb519357 ("arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240210-msm8974-qfprom-v3-1-26c424160334@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 090c4094574705b0afc7d37825cdc5d06f0e7e02 ]
External clocks should be defined as zero-Hz clocks in the SoC .dtsi,
and overridden in the board .dts when present.
Correct the clock rate of extal1 from 25 to 26 MHz, to match the crystal
oscillator present on the APE6-EVM board.
Fixes: a76809a329d6ebae ("ARM: shmobile: r8a73a4: Common clock framework DT description")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/1692bc8cd465d62168cbf110522ad62a7af3f606.1705315614.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9928f0a9e7c0cee3360ca1442b4001d34ad67556 ]
Drop "interrupt-names" property, since it is broken. The drivers/dma/mxs-dma.c
in Linux kernel does not use it, the property contains duplicate array entries
in existing DTs, and even malformed entries (gmpi, should have been gpmi). Get
rid of that optional property altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e9f5cd85f1f931bb7b64031492f7051187ccaac7 ]
Currently the dtbs_check generates warnings like this:
$nodename:0: 'dma-apbh@110000' does not match '^dma-controller(@.*)?$'
So fix all affected dma-apbh node names.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit fdf87a0dc26d0550c60edc911cda42f9afec3557 upstream.
Without the terminator, if a con_id is passed to gpio_find() that
does not exist in the lookup table the function will not stop looping
correctly, and eventually cause an oops.
Cc: stable@vger.kernel.org
Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20240205102337.439002-1-alexander.sverdlin@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b76bbf835d8945080b22b52fc1e6f41cde06865d ]
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Cc: stable@vger.kernel.org
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 68fb3ca0e408e00db1c3f8fccdfa19e274c033be upstream.
We've had issues with gcc and 'asm goto' before, and we created a
'asm_volatile_goto()' macro for that in the past: see commits
3f0116c3238a ("compiler/gcc4: Add quirk for 'asm goto' miscompilation
bug") and a9f180345f53 ("compiler/gcc4: Make quirk for
asm_volatile_goto() unconditional").
Then, much later, we ended up removing the workaround in commit
43c249ea0b1e ("compiler-gcc.h: remove ancient workaround for gcc PR
58670") because we no longer supported building the kernel with the
affected gcc versions, but we left the macro uses around.
Now, Sean Christopherson reports a new version of a very similar
problem, which is fixed by re-applying that ancient workaround. But the
problem in question is limited to only the 'asm goto with outputs'
cases, so instead of re-introducing the old workaround as-is, let's
rename and limit the workaround to just that much less common case.
It looks like there are at least two separate issues that all hit in
this area:
(a) some versions of gcc don't mark the asm goto as 'volatile' when it
has outputs:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=98619
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110420
which is easy to work around by just adding the 'volatile' by hand.
(b) Internal compiler errors:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110422
which are worked around by adding the extra empty 'asm' as a
barrier, as in the original workaround.
but the problem Sean sees may be a third thing since it involves bad
code generation (not an ICE) even with the manually added 'volatile'.
The same old workaround works for this case, even if this feels a
bit like voodoo programming and may only be hiding the issue.
Reported-and-tested-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/all/20240208220604.140859-1-seanjc@google.com/
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Andrew Pinski <quic_apinski@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 858d83ca4b50bbc8693d95cc94310e6d791fb2e6 ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3aa1a82fb20ee97597022f6528823a8ab82bde6 ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68c711b882c262e36895547cddea2c2d56ce611d ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27ded76ef0fcfcf939914532aae575cf23c221b4 ]
Fix hdmi ports node so that it matches the
rockchip,inno-hdmi.yaml binding.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/9a2afac1-ed5c-382d-02b0-b2f5f1af3abb@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4aadb841ed49bada1415c48c44d21f5b69e01299 ]
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: nand-controller@33002000:
#size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d4ac04fa7c3f6dc263dba6f575a2ec7a2d4eca8 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 64bac5ea17d527872121adddfee869c7a0618f8f ]
The prototype was hidden in an #ifdef on x86, which causes a warning:
kernel/irq_work.c:72:13: error: no previous prototype for 'arch_irq_work_raise' [-Werror=missing-prototypes]
Some architectures have a working prototype, while others don't.
Fix this by providing it in only one place that is always visible.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 710dd03464e4ab5b3d329768388b165d61958577 ]
The USB SS PHY interrupt needs to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states.
Fixes: fea4b41022f3 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit de95f139394a5ed82270f005bc441d2e7c1e51b7 ]
The USB DP/DM HS PHY interrupts need to be provided by the PDC interrupt
controller in order to be able to wake the system up from low-power
states and to be able to detect disconnect events, which requires
triggering on falling edges.
A recent commit updated the trigger type but failed to change the
interrupt provider as required. This leads to the current Linux driver
failing to probe instead of printing an error during suspend and USB
wakeup not working as intended.
Fixes: d0ec3c4c11c3 ("ARM: dts: qcom: sdx55: fix USB wakeup interrupt types")
Fixes: fea4b41022f3 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cc25bd06c16aa582596a058d375b2e3133f79b93 ]
The Qualcomm PDC interrupt controller binding expects two cells in
interrupt specifiers.
Fixes: 9d038b2e62de ("ARM: dts: qcom: Add SDX55 platform and MTP board support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231213173131.29436-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 84228d5e29dbc7a6be51e221000e1d122125826c ]
The kernel hangs for a good 12 seconds without any info being printed to
dmesg, very early in the boot process, if this regulator is not enabled.
Force-enable it to work around this issue, until we know more about the
underlying problem.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Cc: stable@vger.kernel.org # v5.8+
Link: https://lore.kernel.org/r/20231206221556.15348-2-paul@crapouillou.net
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0ec3c4c11c3b30e1f2d344973b2a7bf0f986734 ]
The DP/DM wakeup interrupts are edge triggered and which edge to trigger
on depends on use-case and whether a Low speed or Full/High speed device
is connected.
Fixes: fea4b41022f3 ("ARM: dts: qcom: sdx55: Add USB3 and PHY support")
Cc: stable@vger.kernel.org # 5.12
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20231120164331.8116-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|