Age | Commit message (Collapse) | Author | Files | Lines |
|
[ Upstream commit fdaa3725831972284ef2779ddba00491d9dbbfca ]
- The code relies on rc_pci_fixup being called, which only happens
when CONFIG_PCI_QUIRKS is enabled, so add that to Kconfig. Omitting
this causes a booting failure with a non-obvious cause.
- Update rc_pci_fixup to set the class properly, copying the
more modern style from other places
- Correct the rc_pci_fixup comment
This patch just re-applies commit 1dc831bf53fd ("ARM: Kirkwood: Update
PCI-E fixup") for all other Marvell ARM platforms which have same buggy
PCIe controller and do not use pci-mvebu.c controller driver yet.
Long-term goal for these Marvell ARM platforms should be conversion to
pci-mvebu.c controller driver and removal of these fixups in arch code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2d16803c562ecc644803d42ba98a8e0aef9c014e ]
BLAKE2s has no currently known use as an shash. Just remove all of this
unnecessary plumbing. Removing this shash was something we talked about
back when we were making BLAKE2s a built-in, but I simply never got
around to doing it. So this completes that project.
Importantly, this fixs a bug in which the lib code depends on
crypto_simd_disabled_for_test, causing linker errors.
Also add more alignment tests to the selftests and compare SIMD and
non-SIMD compression functions, to make up for what we lose from
testmgr.c.
Reported-by: gaochao <gaochao49@huawei.com>
Cc: Eric Biggers <ebiggers@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: stable@vger.kernel.org
Fixes: 6048fdcc5f26 ("lib/crypto: blake2s: include as built-in")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 251e90e7e346a23742b90e2c4db19d322e071d99 ]
Commit fa1f57421e0b ("xen/virtio: Enable restricted memory access using
Xen grant mappings") introduced a new requirement for using virtio
devices: the backend now needs to support the VIRTIO_F_ACCESS_PLATFORM
feature.
This is an undue requirement for non-PV guests, as those can be operated
with existing backends without any problem, as long as those backends
are running in dom0.
Per default allow virtio devices without grant support for non-PV
guests.
On Arm require VIRTIO_F_ACCESS_PLATFORM for devices having been listed
in the device tree to use grants.
Add a new config item to always force use of grants for virtio.
Fixes: fa1f57421e0b ("xen/virtio: Enable restricted memory access using Xen grant mappings")
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Tested-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> # Arm64 guest using Xen
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20220622063838.8854-4-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8d8be8dd7c1f5d50f84ecc7a6a41962da48c6164 ]
The remoteproc configuration in qcom-msm8974.dtsi is incomplete because
it lacks the regulator supplies that should be added in the board DT
files. Some of the msm8974 boards are currently missing the regulator
supplies and should have the remoteprocs disabled to avoid making use
of the incomplete configuration.
This also fixes dtbs_check warnings after moving "qcom,msm8974-mss-pil"
to DT schema, which rightfully complains that the -supply properties
are missing for some boards:
qcom-apq8074-dragonboard.dtb:
remoteproc@fc880000: 'pll-supply' is a required property
From schema: remoteproc/qcom,msm8916-mss-pil.yaml
remoteproc@fc880000: 'mss-supply' is a required property
From schema: remoteproc/qcom,msm8916-mss-pil.yaml
remoteproc@fc880000: 'oneOf' conditional failed, one must be fixed:
'power-domains' is a required property
'power-domain-names' is a required property, or
'cx-supply' is a required property
'mx-supply' is a required property
Cc: Luca Weiss <luca@z3ntu.xyz>
Cc: Konrad Dybcio <konrad.dybcio@somainline.org>
Fixes: f300826d27be ("ARM: dts: qcom-msm8974: Sort and clean up nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220712124421.3129206-4-stephan.gerhold@kernkonzept.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e2759fa0676c9a32bbddb9aff955b54bb35066ad ]
The PM8841 temperature sensor has to define thermal-sensor-cells.
Fixes: dab8134ca072 ("ARM: dts: qcom: Add PM8841 functions device nodes")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220608112702.80873-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7a16ea7f3a5ec0f30b146b058c273b7a9c8ceadf ]
The OCMEM bindings require ranges property.
Fixes: a2cc991ed634 ("ARM: dts: qcom: msm8974: add ocmem node")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220607171848.535128-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ab1489017aa7a9f02e24bee73cf9ec8079cd3909 ]
IRQ_TYPE_NONE is invalid, so use the correct interrupt type.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Fixes: b05f82b152c9 ("ARM: dts: qcom: msm8974: Add blsp2_uart7 for bluetooth on sirius")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220522083618.17894-1-luca@z3ntu.xyz
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit eb9e93937756a05787977875830c0dc482cb57e0 ]
Replace gcc PXO phandle to pxo_board fixed clock declared in the dts.
gcc driver doesn't provide PXO_SRC as it's a fixed-clock. This cause a
kernel panic if any driver actually try to use it.
Fixes: 40cf5c884a96 ("ARM: dts: qcom: add L2CC and RPM for IPQ8064")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220430055118.1947-2-ansuelsmth@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d1ff2559cef0f6f8d97fba6337b28adb10689e16 ]
of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 00f7dc636366 ("ARM: zynq: Add support for SOC_BUS")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220605082807.21526-1-linmq006@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 942228fbf5d4901112178b93d41225be7c0dd9de ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 1e037794f7f0 ("ARM: OMAP3+: PRM: register interrupt information from DT")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220526073724.21169-1-linmq006@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9705db1eff38d6b9114121f9e253746199b759c9 ]
omapdss_find_dss_of_node() calls of_find_compatible_node() to get device
node. of_find_compatible_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() in later error path and normal path.
Fixes: e0c827aca0730 ("drm/omap: Populate DSS children in omapdss driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220601044858.3352-1-linmq006@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc590cdc31f636ea15658f1206c3e380a53fb78e ]
'reg' property is required in SSBI children:
qcom-mdm9615-wp8548-mangoh-green.dtb: gpio@150: 'reg' is a required property
Fixes: 2c5e596524e7 ("ARM: dts: Add MDM9615 dtsi")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 33c39140cc298e0d4e36083cb9a665a837773a60 ]
The AST2600 EVB A1 board should have dedicated compatible.
Fixes: a72955180372 ("ARM: dts: aspeed: ast2600evb: Add dts file for A1 and A0")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220529104928.79636-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit aa5e06208500a0db41473caebdee5a2e81d5a277 ]
The AST2600 EVB board should have dedicated compatible.
Fixes: 2ca5646b5c2f ("ARM: dts: aspeed: Add AST2600 and EVB")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220529104928.79636-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 30b276fca5c0644f3cb17bceb1bd6a626c670184 ]
The AST2500 EVB board should have dedicated compatible.
Fixes: 02440622656d ("arm/dst: Add Aspeed ast2500 device tree")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220529104928.79636-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 9c0919acb3fa7c1a24e384ff912f2d88f060c373 ]
The STMPE MFD device binding requires the child node to have a fixed
name, i.e. with '_', not '-'. Otherwise the stmpe_adc, stmpe_touchscreen
drivers will not be probed.
Fixes: 56086b5e804f ("ARM: dts: imx6qdl-apalis: Avoid underscore in node name")
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 32f054fef145878c5331f9dd343014970a15ebfa ]
Correct CAN controller comment. It is a MCP2515 rather than a mpc258x.
Fixes: 66d59b678a87 ("ARM: dts: imx7-colibri: add MCP2515 CAN controller")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0ef1969ea5699b00394e1a8c8c7f927b2d0bc5bb ]
Move aliases, chosen, extcon and gpio-keys to module-level device tree
given they are standard Colibri functionalities.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit fd5d2974652c96935d94301af6eaf6b3585ab330 ]
The pin GPIO1_IO01 externally pulls down, it is required to sequentially
connect this pin (signal WAKE_MICO#) to +3v3 and then disconnect it to
trigger a wakeup interrupt.
Adding the flag GPIO_PULL_DOWN allows the system to be woken up just
connecting the pin GPIO1_IO01 to +3v3.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 136f88458d829987548b3321e7122e05acd78dd9 ]
Add USB dual-role switching using extcon.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dbeb8e72cc51536a70313e6d523dcb1429b40477 ]
Rename display interface to match other modules to make it easier to
use device tree overlays.
The parallel RGB interface (lcdif) and all related stuff turn on in a
device tree overlay. Keep them disabled in the main devicetree.
As these subsystems are provided by module and not a part of boards,
move their definitions into the module-level devicetree.
Disable ad7879 touchscreen which turns on in a devic tree overlay.
Remains it disabled in the main devicetree.
Move Atmel MXT capacitive touch controller device tree nodes from
carrier board to module level and add iomux pinctl groups for both the
Capacitive Touch Adapter (using SODIMM 28/30) and the capacitive touch
connector as found on later carrier boards (using SODIMM 106/107).
Keep touchscreen and display nodes enabled for NAND based i.MX 7
modules, since device tree overlays are not yet supported. For the
Colibri Evaluation Board keep the Capacitive Touch Adapter node
disabled and PWM2, PWM3 enabled instead.
For eMMC based modules keep nodes disabled to work in conjunction with
device tree overlays.
Add the iomuxc pinctrl group for the LVDS transceiver related signals to
use it in a device tree overlay.
While at it also alphabetically re=order them properties.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ba28db60d34271e8a3cf4d7158d71607e8b1e57f ]
Each cpu-core is supposed to list its supply separately, add supply for
cpu1.
Fixes: 2d7401f8632f ("ARM: dts: imx7d: Add cpu1 supply")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cb23389a2458c2e4bfd6c86a513cbbe1c4d35e76 ]
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: b8eb35fd594a ("ARM: bcm281xx: Add L2 cache enable code")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 75a185fb92e58ccd3670258d8d3b826bd2fa6d29 ]
In rcar_gen2_regulator_quirk(), for_each_matching_node_and_match() will
automatically increase and decrease the refcount. However, we should
call of_node_get() for the new reference created in 'quirk->np'.
Besides, we also should call of_node_put() before the 'quirk' being
freed.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220701121804.234223-1-windhl@126.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ae500b351ab0006d933d804a2b7507fe1e98cecc ]
The trigger type should be LEVEL_HIGH. So fix it!
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220530080842.37024-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5cdbab96bab314c6f2f5e4e8b8a019181328bf5f ]
In pdata_quirks_init_clocks(), the loop contains
of_find_node_by_name() but without corresponding of_node_put().
Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220618020603.4055792-1-windhl@126.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 50b87a32a79bca6e275918a711fb8cc55e16d739 ]
In omapdss_init_fbdev(), of_find_node_by_name() will return a node
pointer with refcount incremented. We should use of_node_put() when
it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Message-Id: <20220617145803.4050918-1-windhl@126.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e24c75f02a81d6ddac0072cbd7a03e799c19d558 ]
This was fixed wrong so fix it. Now verified by using
iio-sensor-proxy monitor-sensor test program.
Link: https://lore.kernel.org/r/20220611205138.491513-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0b2152e428ab91533a02888ff24e52e788dc4637 ]
This was fixed wrong so fix it again. Now verified by using
iio-sensor-proxy monitor-sensor test program.
Link: https://lore.kernel.org/r/20220611204249.472250-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 013fda41c03e6bcb3dc416669187b609e9e5fdbc ]
This was fixed wrong so fix it again. Now verified by using
iio-sensor-proxy monitor-sensor test program.
Link: https://lore.kernel.org/r/20220609083516.329281-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 935327a73553001f8d81375c76985d05f604507f ]
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM i2c
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.
Odd stuff:
- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
This causes the system to immediately shutdown! Looking at reported
"418 degree Celsius" suggests that this sensor is not working.
WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0c6cf86e1ab433b2d421880fdd9c6e954f404948 ]
imx6ul is not compatible to imx6sx, both have different erratas.
Fixes the dt_binding_check warning:
spi@21e0000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-qspi', 'fsl,imx6sx-qspi'] is too long
Additional items are not allowed ('fsl,imx6sx-qspi' was unexpected)
'fsl,imx6ul-qspi' is not one of ['fsl,ls1043a-qspi']
'fsl,imx6ul-qspi' is not one of ['fsl,imx8mq-qspi']
'fsl,ls1021a-qspi' was expected
'fsl,imx7d-qspi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1a884d17ca324531634cce82e9f64c0302bdf7de ]
In yaml binding "fsl,imx6ul-lcdif" is listed as compatible to imx6sx-lcdif,
but not imx28-lcdif. Change the list accordingly. Fixes the
dt_binding_check warning:
lcdif@21c8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-lcdif', 'fsl,imx28-lcdif'] is too long
Additional items are not allowed ('fsl,imx28-lcdif' was unexpected)
'fsl,imx6ul-lcdif' is not one of ['fsl,imx23-lcdif', 'fsl,imx28-lcdif',
'fsl,imx6sx-lcdif']
'fsl,imx6sx-lcdif' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e0aca931a2c7c29c88ebf37f9c3cd045e083483d ]
"fsl,imx6ul-csi" was never listed as compatible to "fsl,imx7-csi", neither
in yaml bindings, nor previous txt binding. Remove the imx7 part. Fixes
the dt schema check warning:
csi@21c4000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-csi', 'fsl,imx7-csi'] is too long
Additional items are not allowed ('fsl,imx7-csi' was unexpected)
'fsl,imx8mm-csi' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 7d15e0c9a515494af2e3199741cdac7002928a0e ]
According to binding, the compatible shall only contain imx6ul and imx21
compatibles. Fixes the dt_binding_check warning:
keypad@20b8000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx6ul-kpp', 'fsl,imx6q-kpp', 'fsl,imx21-kpp'] is too long
Additional items are not allowed ('fsl,imx6q-kpp', 'fsl,imx21-kpp' were
unexpected)
Additional items are not allowed ('fsl,imx21-kpp' was unexpected)
'fsl,imx21-kpp' was expected
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edb67843983bbdf61b4c8c3c50618003d38bb4ae ]
operating-points is a uint32-matrix as per opp-v1.yaml. Change it
accordingly. While at it, change fsl,soc-operating-points as well,
although there is no bindings file (yet). But they should have the same
format. Fixes the dt_binding_check warning:
cpu@0: operating-points:0: [696000, 1275000, 528000, 1175000, 396000,
1025000, 198000, 950000] is too long
cpu@0: operating-points:0: Additional items are not allowed (528000,
1175000, 396000, 1025000, 198000, 950000 were unexpected)
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5655699cf5cff9f4c4ee703792156bdd05d1addf ]
All 3 properties are required by sram.yaml. Fixes the dtbs_check
warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 9b0dc7abb5cc43a2dbf90690c3c6011dcadc574d upstream.
An interrupt for USB device are shared with USB host. Set interrupt-names
property to common "dwc_usb3" instead of "host" and "peripheral".
Cc: stable@vger.kernel.org
Fixes: 45be1573ad19 ("ARM: dts: uniphier: Add USB3 controller nodes")
Reported-by: Ryuta NAKANISHI <nakanishi.ryuta@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull ARM fixes from Russell King:
"Last set of ARM fixes for 5.19:
- fix for MAX_DMA_ADDRESS overflow
- fix for find_*_bit performing an out of bounds memory access"
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: findbit: fix overflowing offset
ARM: 9216/1: Fix MAX_DMA_ADDRESS overflow
|
|
When offset is larger than the size of the bit array, we should not
attempt to access the array as we can perform an access beyond the
end of the array. Fix this by changing the pre-condition.
Using "cmp r2, r1; bhs ..." covers us for the size == 0 case, since
this will always take the branch when r1 is zero, irrespective of
the value of r2. This means we can fix this bug without adding any
additional code!
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Commit 26f09e9b3a06 ("mm/memblock: add memblock memory allocation apis")
added a check to determine whether arm_dma_zone_size is exceeding the
amount of kernel virtual address space available between the upper 4GB
virtual address limit and PAGE_OFFSET in order to provide a suitable
definition of MAX_DMA_ADDRESS that should fit within the 32-bit virtual
address space. The quantity used for comparison was off by a missing
trailing 0, leading to MAX_DMA_ADDRESS to be overflowing a 32-bit
quantity.
This was caught thanks to CONFIG_DEBUG_VIRTUAL on the bcm2711 platform
where we define a dma_zone_size of 1GB and we have a PAGE_OFFSET value
of 0xc000_0000 (CONFIG_VMSPLIT_3G) leading to MAX_DMA_ADDRESS being
0x1_0000_0000 which overflows the unsigned long type used throughout
__pa() and then __virt_addr_valid(). Because the virtual address passed
to __virt_addr_valid() would now be 0, the function would loudly warn
and flood the kernel log, thus making the platform unable to boot
properly.
Fixes: 26f09e9b3a06 ("mm/memblock: add memblock memory allocation apis")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
Laurence reports:
"Kernel >5.18 on Zaurus has a bug where the power management code can't
talk to devices, emitting the following errors:
sharpsl-pm sharpsl-pm: Error: AC check failed: voltage -22.
sharpsl-pm sharpsl-pm: Charging Error!
sharpsl-pm sharpsl-pm: Warning: Cannot read main battery!
Looking at the recent changes, I found that commit 31455bbda208 ("spi:
pxa2xx_spi: Convert to use GPIO descriptors") replaced the deprecated
SPI chip select platform device code with a gpiod lookup table. However,
this didn't seem to work until I changed the `dev_id` member from the
device name to the bus id. I'm not entirely sure why this is necessary,
but I suspect it is related to the fact that in sysfs SPI devices are
attached under /sys/devices/.../dev_name/spi_master/spiB/spiB.C, rather
than directly to the device."
After reviewing the change I conclude that the same fix is needed
for all affected boards.
Fixes: 31455bbda208 ("spi: pxa2xx_spi: Convert to use GPIO descriptors")
Reported-by: Laurence de Bruxelles <lfdebrux@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220722114611.1517414-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes for 5.19 #3
It contains one fix for LAN966 based SoCs fixing the frequency of
sys_clk. sys_clk is feeding different IPs so having proper frequency
for it in DT is necessary for proper working of different drivers.
* tag 'at91-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: lan966x: fix sys_clk frequency
Link: https://lore.kernel.org/r/20220721075705.1739915-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The sys_clk frequency is 165.625MHz. The register reference of the
Generic Clock controller lists the CPU clock as 600MHz, the DDR clock as
300MHz and the SYS clock as 162.5MHz. This is wrong. It was first
noticed during the fan driver development and it was measured and
verified via the CLK_MON output of the SoC which can be configured to
output sys_clk/64.
The core PLL settings (which drives the SYS clock) seems to be as
follows:
DIVF = 52
DIVQ = 3
DIVR = 1
With a refernce clock of 25MHz, this means we have a post divider clock
Fpfd = Fref / (DIVR + 1) = 25MHz / (1 + 1) = 12.5MHz
The resulting VCO frequency is then
Fvco = Fpfd * (DIVF + 1) * 2 = 12.5MHz * (52 + 1) * 2 = 1325MHz
And the output frequency is
Fout = Fvco / 2^DIVQ = 1325MHz / 2^3 = 165.625Mhz
This all adds up to the constrains of the PLL:
10MHz <= Fpfd <= 200MHz
20MHz <= Fout <= 1000MHz
1000MHz <= Fvco <= 2000MHz
Fixes: 290deaa10c50 ("ARM: dts: add DT for lan966 SoC and 2-port board pcb8291")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220326194028.2945985-1-michael@walle.cc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the contents are bugfixes for the devicetree files:
- A Qualcomm MSM8974 pin controller regression, caused by a cleanup
patch that gets partially reverted here.
- Missing properties for Broadcom BCM49xx to fix timer detection and
SMP boot.
- Fix touchscreen pinctrl for imx6ull-colibri board
- Multiple fixes for Rockchip rk3399 based machines including the vdu
clock-rate fix, otg port fix on Quartz64-A and ethernet on
Quartz64-B
- Fixes for misspelled DT contents causing minor problems on
imx6qdl-ts7970m, orangepi-zero, sama5d2, kontron-kswitch-d10, and
ls1028a
And a couple of changes elsewhere:
- Fix binding for Allwinner D1 display pipeline
- Trivial code fixes to the TEE and reset controller driver
subsystems and the rockchip platform code.
- Multiple updates to the MAINTAINERS files, marking the Palm Treo
support as orphaned, and fixing some entries for added or changed
file names"
* tag 'soc-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
ARM: dts: at91: sama5d2: Fix typo in i2s1 node
tee: tee_get_drvdata(): fix description of return value
optee: Remove duplicate 'of' in two places.
ARM: dts: kswitch-d10: use open drain mode for coma-mode pins
ARM: dts: colibri-imx6ull: fix snvs pinmux group
optee: smc_abi.c: fix wrong pointer passed to IS_ERR/PTR_ERR()
MAINTAINERS: add polarfire rng, pci and clock drivers
MAINTAINERS: mark ARM/PALM TREO SUPPORT orphan
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
dt-bindings: display: sun4i: Fix D1 pipeline count
ARM: dts: qcom: msm8974: re-add missing pinctrl
reset: Fix devm bulk optional exclusive control getter
MAINTAINERS: rectify entry for SYNOPSYS AXS10x RESET CONTROLLER DRIVER
ARM: rockchip: Add missing of_node_put() in rockchip_suspend_init()
arm64: dts: rockchip: Assign RK3399 VDU clock rate
arm64: dts: rockchip: Fix Quartz64-A dwc3 otg port behavior
...
|
|
Pull ARM fixes from Russell King:
- quieten the spectre-bhb prints
- mark flattened device tree sections as shareable
- remove some obsolete CPU domain code and help text
- fix thumb unaligned access abort emulation
- fix amba_device_add() refcount underflow
- fix literal placement
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9208/1: entry: add .ltorg directive to keep literals in range
ARM: 9207/1: amba: fix refcount underflow if amba_device_add() fails
ARM: 9214/1: alignment: advance IT state after emulating Thumb instruction
ARM: 9213/1: Print message about disabled Spectre workarounds only once
ARM: 9212/1: domain: Modify Kconfig help text
ARM: 9211/1: domain: drop modify_domain()
ARM: 9210/1: Mark the FDT_FIXED sections as shareable
ARM: 9209/1: Spectre-BHB: avoid pr_info() every time a CPU comes out of idle
|
|
LKP reports a build issue on Clang, related to a literal load of
__current issued through the ldr_va macro. This turns out to be due to
the fact that group relocations are disabled when CONFIG_COMPILE_TEST=y,
which means that the ldr_va macro resolves to a pair of LDR
instructions, the first one being a literal load issued too far from its
literal pool.
Due to the introduction of a couple of new uses of this macro in commit
508074607c7b95b2 ("ARM: 9195/1: entry: avoid explicit literal loads"),
the literal pools end up getting rearranged in a way that causes the
literal for __current to go out of range. Let's fix this up by putting a
.ltorg directive in a suitable place in the code.
Link: https://lore.kernel.org/all/202205290805.1vZLAr36-lkp@intel.com/
Fixes: 508074607c7b95b2 ("ARM: 9195/1: entry: avoid explicit literal loads")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm DTS fixe for 5.19
The pinctrl state was lost in the recent refactoring of the MSM8974
Devicetree, this contains a fix for this.
* tag 'qcom-dts-fixes-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974: re-add missing pinctrl
Link: https://lore.kernel.org/r/20220713030627.1371156-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.19, round 3:
- Fix GPIO property for imx6qdl-ts7970 board.
- Fix touchscreen pinctrl for imx6ull-colibri board by moving iomuxc-snvs
pin to the correct controller device.
- Fix SFP node of fsl-ls1028a to have a required clock property.
* tag 'imx-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: colibri-imx6ull: fix snvs pinmux group
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
Link: https://lore.kernel.org/r/20220709032716.GA9868@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
- Fix SPI NOR compatible on Orange Pi Zero
* tag 'sunxi-fixes-for-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
Link: https://lore.kernel.org/r/Ysh44qUmdmF6TWS6@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|