| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The defines for SVCR call it SVCR_EL0 however the architecture calls the
register SVCR with no _EL0 suffix. In preparation for generating the sysreg
definitions rename to match the architecture, no functional change.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220510161208.631259-6-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The bitfield definitions for SVCR have a SYS_ added to the names of the
constant which will be a problem for automatic generation. Remove the
prefixes, no functional change.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220510161208.631259-5-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Since the vector length configuration mechanism is identical between SVE
and SME we share large elements of the code including the definition for
the maximum vector length. Unfortunately when we were defining the ABI
for SVE we included not only the actual maximum vector length of 2048
bits but also the value possible if all the bits reserved in the
architecture for expansion of the LEN field were used, 16384 bits.
This starts creating problems if we try to allocate anything for the ZA
matrix based on the maximum possible vector length, as we do for the
regset used with ptrace during the process of generating a core dump.
While the maximum potential size for ZA with the current architecture is
a reasonably managable 64K with the higher reserved limit ZA would be
64M which leads to entirely reasonable complaints from the memory
management code when we try to allocate a buffer of that size. Avoid
these issues by defining the actual maximum vector length for the
architecture and using it for the SME regsets.
Also use the full ZA_PT_SIZE() with the header rather than just the
actual register payload when specifying the size, fixing support for the
largest vector lengths now that we have this new, lower define. With the
SVE maximum this did not cause problems due to the extra headroom we
had.
While we're at it add a comment clarifying why even though ZA is a
single register we tell the regset code that it is a multi-register
regset.
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/20220505221517.1642014-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The streaming mode SVE registers are represented using the same data
structures as for SVE but since the vector lengths supported and in use
may not be the same as SVE we represent them with a new type NT_ARM_SSVE.
Unfortunately we only have a single 16 bit reserved field available in
the header so there is no space to fit the current and maximum vector
length for both standard and streaming SVE mode without redefining the
structure in a way the creates a complicatd and fragile ABI. Since FFR
is not present in streaming mode it is read and written as zero.
Setting NT_ARM_SSVE registers will put the task into streaming mode,
similarly setting NT_ARM_SVE registers will exit it. Reads that do not
correspond to the current mode of the task will return the header with
no register data. For compatibility reasons on write setting no flag for
the register type will be interpreted as setting SVE registers, though
users can provide no register data as an alternative mechanism for doing
so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-21-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
By default all SME operations in userspace will trap. When this happens
we allocate storage space for the SME register state, set up the SVE
registers and disable traps. We do not need to initialize ZA since the
architecture guarantees that it will be zeroed when enabled and when we
trap ZA is disabled.
On syscall we exit streaming mode if we were previously in it and ensure
that all but the lower 128 bits of the registers are zeroed while
preserving the state of ZA. This follows the aarch64 PCS for SME, ZA
state is preserved over a function call and streaming mode is exited.
Since the traps for SME do not distinguish between streaming mode SVE
and ZA usage if ZA is in use rather than reenabling traps we instead
zero the parts of the SVE registers not shared with FPSIMD and leave SME
enabled, this simplifies handling SME traps. If ZA is not in use then we
reenable SME traps and fall through to normal handling of SVE.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-17-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Allocate space for storing ZA on first access to SME and use that to save
and restore ZA state when context switching. We do this by using the vector
form of the LDR and STR ZA instructions, these do not require streaming
mode and have implementation recommendations that they avoid contention
issues in shared SMCU implementations.
Since ZA is architecturally guaranteed to be zeroed when enabled we do not
need to explicitly zero ZA, either we will be restoring from a saved copy
or trapping on first use of SME so we know that ZA must be disabled.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-16-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When in streaming mode we need to save and restore the streaming mode
SVE register state rather than the regular SVE register state. This uses
the streaming mode vector length and omits FFR but is otherwise identical,
if TIF_SVE is enabled when we are in streaming mode then streaming mode
takes precedence.
This does not handle use of streaming SVE state with KVM, ptrace or
signals. This will be updated in further patches.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-15-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In SME the use of both streaming SVE mode and ZA are tracked through
PSTATE.SM and PSTATE.ZA, visible through the system register SVCR. In
order to context switch the floating point state for SME we need to
context switch the contents of this register as part of context
switching the floating point state.
Since changing the vector length exits streaming SVE mode and disables
ZA we also make sure we update SVCR appropriately when setting vector
length, and similarly ensure that new threads have streaming SVE mode
and ZA disabled.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-14-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
As for SVE provide a prctl() interface which allows processes to
configure their SME vector length.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-12-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The vector lengths used for SME are controlled through a similar set of
registers to those for SVE and enumerated using a similar algorithm with
some slight differences due to the fact that unlike SVE there are no
restrictions on which combinations of vector lengths can be supported
nor any mandatory vector lengths which must be implemented. Add a new
vector type and implement support for enumerating it.
One slightly awkward feature is that we need to read the current vector
length using a different instruction (or enter streaming mode which
would have the same issue and be higher cost). Rather than add an ops
structure we add special cases directly in the otherwise generic
vec_probe_vqs() function, this is a bit inelegant but it's the only
place where this is an issue.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-10-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch introduces basic cpufeature support for discovering the presence
of the Scalable Matrix Extension.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-9-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
As with SVE rather than impose ambitious toolchain requirements for SME
we manually encode the few instructions which we require in order to
perform the work the kernel needs to do. The instructions used to save
and restore context are provided as assembler macros while those for
entering and leaving streaming mode are done in asm volatile blocks
since they are expected to be used from C.
We could do the SMSTART and SMSTOP operations with read/modify/write
cycles on SVCR but using the aliases provided for individual field
accesses should be slightly faster. These instructions are aliases for
MSR but since our minimum toolchain requirements are old enough to mean
that we can't use the sX_X_cX_cX_X form and they always use xzr rather
than taking a value like write_sysreg_s() wants we just use .inst.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-7-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In preparation for adding SME support update the bulk of the implementation
for the vector length configuration prctl() calls to be independent of
vector type.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211210184133.320748-3-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Fixes build problems for configurations with KVM enabled but SVE disabled.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211022141635.2360415-2-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently when restoring the SVE state we supply the SVE vector length
as an argument to sve_load_state() and the underlying macros. This becomes
inconvenient with the addition of SME since we may need to restore any
combination of SVE and SME vector lengths, and we already separately
restore the vector length in the KVM code. We don't need to know the vector
length during the actual register load since the SME load instructions can
index into the data array for us.
Refactor the interface so we explicitly set the vector length separately
to restoring the SVE registers in preparation for adding SME support, no
functional change should be involved.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211019172247.3045838-9-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
With the introduction of SME we will have a second vector length in the
system, enumerated and configured in a very similar fashion to the
existing SVE vector length. While there are a few differences in how
things are handled this is a relatively small portion of the overall
code so in order to avoid code duplication we factor out
We create two structs, one vl_info for the static hardware properties
and one vl_config for the runtime configuration, with an array
instantiated for each and update all the users to reference these. Some
accessor functions are provided where helpful for readability, and the
write to set the vector length is put into a function since the system
register being updated needs to be chosen at compile time.
This is a mostly mechanical replacement, further work will be required
to actually make things generic, ensuring that we handle those places
where there are differences properly.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211019172247.3045838-8-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In a system with SME there are parallel vector length controls for SVE and
SME vectors which function in much the same way so it is desirable to
share the code for handling them as much as possible. In order to prepare
for doing this add a layer of accessor functions for the various VL related
operations on tasks.
Since almost all current interactions are actually via task->thread rather
than directly with the thread_info the accessors use that. Accessors are
provided for both generic and SVE specific usage, the generic accessors
should be used for cases where register state is being manipulated since
the registers are shared between streaming and regular SVE so we know that
when SME support is implemented we will always have to be in the appropriate
mode already and hence can generalise now.
Since we are using task_struct and we don't want to cause widespread
inclusion of sched.h the acessors are all out of line, it is hoped that
none of the uses are in a sufficiently critical path for this to be an
issue. Those that are most likely to present an issue are in the same
translation unit so hopefully the compiler may be able to inline anyway.
This is purely adding the layer of abstraction, additional work will be
needed to support tasks using SME.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211019172247.3045838-7-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
SME introduces streaming SVE mode in which FFR is not present and the
instructions for accessing it UNDEF. In preparation for handling this
update the low level SVE state access functions to take a flag specifying
if FFR should be handled. When saving the register state we store a zero
for FFR to guard against uninitialized data being read. No behaviour change
should be introduced by this patch.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211019172247.3045838-5-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
There are no users outside fpsimd.c so make sve_state_size() static.
KVM open codes an equivalent.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211019172247.3045838-4-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Following optimisations of the SVE register handling we no longer load the
SVE state from a saved copy of the FPSIMD registers, we convert directly
in registers or from one saved state to another. Remove the function so we
don't need to update it during further refactoring.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211019172247.3045838-3-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
This function is not referenced outside fpsimd.c so can be static, making
it that little bit easier to follow what is called from where.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210730165846.18558-1-broonie@kernel.org
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
When the SVE vector length is 128 bits then there are no bits in the Z
registers which are not shared with the V registers so we can skip them
when zeroing state not shared with FPSIMD, this results in a minor
performance improvement.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210512151131.27877-4-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Pull kvm updates from Paolo Bonzini:
"This is a large update by KVM standards, including AMD PSP (Platform
Security Processor, aka "AMD Secure Technology") and ARM CoreSight
(debug and trace) changes.
ARM:
- CoreSight: Add support for ETE and TRBE
- Stage-2 isolation for the host kernel when running in protected
mode
- Guest SVE support when running in nVHE mode
- Force W^X hypervisor mappings in nVHE mode
- ITS save/restore for guests using direct injection with GICv4.1
- nVHE panics now produce readable backtraces
- Guest support for PTP using the ptp_kvm driver
- Performance improvements in the S2 fault handler
x86:
- AMD PSP driver changes
- Optimizations and cleanup of nested SVM code
- AMD: Support for virtual SPEC_CTRL
- Optimizations of the new MMU code: fast invalidation, zap under
read lock, enable/disably dirty page logging under read lock
- /dev/kvm API for AMD SEV live migration (guest API coming soon)
- support SEV virtual machines sharing the same encryption context
- support SGX in virtual machines
- add a few more statistics
- improved directed yield heuristics
- Lots and lots of cleanups
Generic:
- Rework of MMU notifier interface, simplifying and optimizing the
architecture-specific code
- a handful of "Get rid of oprofile leftovers" patches
- Some selftests improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (379 commits)
KVM: selftests: Speed up set_memory_region_test
selftests: kvm: Fix the check of return value
KVM: x86: Take advantage of kvm_arch_dy_has_pending_interrupt()
KVM: SVM: Skip SEV cache flush if no ASIDs have been used
KVM: SVM: Remove an unnecessary prototype declaration of sev_flush_asids()
KVM: SVM: Drop redundant svm_sev_enabled() helper
KVM: SVM: Move SEV VMCB tracking allocation to sev.c
KVM: SVM: Explicitly check max SEV ASID during sev_hardware_setup()
KVM: SVM: Unconditionally invoke sev_hardware_teardown()
KVM: SVM: Enable SEV/SEV-ES functionality by default (when supported)
KVM: SVM: Condition sev_enabled and sev_es_enabled on CONFIG_KVM_AMD_SEV=y
KVM: SVM: Append "_enabled" to module-scoped SEV/SEV-ES control variables
KVM: SEV: Mask CPUID[0x8000001F].eax according to supported features
KVM: SVM: Move SEV module params/variables to sev.c
KVM: SVM: Disable SEV/SEV-ES if NPT is disabled
KVM: SVM: Free sev_asid_bitmap during init if SEV setup fails
KVM: SVM: Zero out the VMCB array used to track SEV ASID association
x86/sev: Drop redundant and potentially misleading 'sev_enabled'
KVM: x86: Move reverse CPUID helpers to separate header file
KVM: x86: Rename GPR accessors to make mode-aware variants the defaults
...
|
|
When we enable SVE usage in userspace after taking a SVE access trap we
need to ensure that the portions of the register state that are not
shared with the FPSIMD registers are zeroed. Currently we do this by
forcing the FPSIMD registers to be saved to the task struct and converting
them there. This is wasteful in the common case where the task state is
loaded into the registers and we will immediately return to userspace
since we can initialise the SVE state directly in registers instead of
accessing multiple copies of the register state in memory.
Instead in that common case do the conversion in the registers and
update the task metadata so that we can return to userspace without
spilling the register state to memory unless there is some other reason
to do so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210312190313.24598-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Compilation fails when KVM is selected and ARM64_SVE isn't.
The root cause is that sve_cond_update_zcr_vq is not defined when
ARM64_SVE is not selected. Fix it by adding an empty definition
when CONFIG_ARM64_SVE=n.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
[maz: simplified commit message, fleshed out dummy #define]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1617183879-48748-1-git-send-email-tanxiaofei@huawei.com
|
|
A common pattern is to conditionally update ZCR_ELx in order
to avoid the "self-synchronizing" effect that writing to this
register has.
Let's provide an accessor that does exactly this.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
In a follow-up patch, we may save the FPSIMD rather than the full SVE
state when the state has to be zeroed on return to userspace (e.g
during a syscall).
Introduce an helper to load SVE vectors from FPSIMD state and zero the rest
of SVE registers.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://lore.kernel.org/r/20200828181155.17745-7-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Introduce a new helper that will zero all SVE registers but the first
128-bits of each vector. This will be used by subsequent patches to
avoid costly store/maipulate/reload sequences in places like do_sve_acc().
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://lore.kernel.org/r/20200828181155.17745-6-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
For a number of years, UAPI headers have been split from kernel-internal
headers. The latter are never exposed to userspace, and always built
with __KERNEL__ defined.
Most headers under arch/arm64 don't have __KERNEL__ guards, but there
are a few stragglers lying around. To make things more consistent, and
to set a good example going forward, let's remove these redundant
__KERNEL__ guards.
In a couple of cases, a trailing #endif lacked a comment describing its
corresponding #if or #ifdef, so these are fixes up at the same time.
Guards in auto-generated crypto code are left as-is, as these guards are
generated by scripting imported from the upstream openssl project
scripts. Guards in UAPI headers are left as-is, as these can be included
by userspace or the kernel.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- arm64 support for syscall emulation via PTRACE_SYSEMU{,_SINGLESTEP}
- Wire up VM_FLUSH_RESET_PERMS for arm64, allowing the core code to
manage the permissions of executable vmalloc regions more strictly
- Slight performance improvement by keeping softirqs enabled while
touching the FPSIMD/SVE state (kernel_neon_begin/end)
- Expose a couple of ARMv8.5 features to user (HWCAP): CondM (new
XAFLAG and AXFLAG instructions for floating point comparison flags
manipulation) and FRINT (rounding floating point numbers to integers)
- Re-instate ARM64_PSEUDO_NMI support which was previously marked as
BROKEN due to some bugs (now fixed)
- Improve parking of stopped CPUs and implement an arm64-specific
panic_smp_self_stop() to avoid warning on not being able to stop
secondary CPUs during panic
- perf: enable the ARM Statistical Profiling Extensions (SPE) on ACPI
platforms
- perf: DDR performance monitor support for iMX8QXP
- cache_line_size() can now be set from DT or ACPI/PPTT if provided to
cope with a system cache info not exposed via the CPUID registers
- Avoid warning on hardware cache line size greater than
ARCH_DMA_MINALIGN if the system is fully coherent
- arm64 do_page_fault() and hugetlb cleanups
- Refactor set_pte_at() to avoid redundant READ_ONCE(*ptep)
- Ignore ACPI 5.1 FADTs reported as 5.0 (infer from the
'arm_boot_flags' introduced in 5.1)
- CONFIG_RANDOMIZE_BASE now enabled in defconfig
- Allow the selection of ARM64_MODULE_PLTS, currently only done via
RANDOMIZE_BASE (and an erratum workaround), allowing modules to spill
over into the vmalloc area
- Make ZONE_DMA32 configurable
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (54 commits)
perf: arm_spe: Enable ACPI/Platform automatic module loading
arm_pmu: acpi: spe: Add initial MADT/SPE probing
ACPI/PPTT: Add function to return ACPI 6.3 Identical tokens
ACPI/PPTT: Modify node flag detection to find last IDENTICAL
x86/entry: Simplify _TIF_SYSCALL_EMU handling
arm64: rename dump_instr as dump_kernel_instr
arm64/mm: Drop [PTE|PMD]_TYPE_FAULT
arm64: Implement panic_smp_self_stop()
arm64: Improve parking of stopped CPUs
arm64: Expose FRINT capabilities to userspace
arm64: Expose ARMv8.5 CondM capability to userspace
arm64: defconfig: enable CONFIG_RANDOMIZE_BASE
arm64: ARM64_MODULES_PLTS must depend on MODULES
arm64: bpf: do not allocate executable memory
arm64/kprobes: set VM_FLUSH_RESET_PERMS on kprobe instruction pages
arm64/mm: wire up CONFIG_ARCH_HAS_SET_DIRECT_MAP
arm64: module: create module allocations without exec permissions
arm64: Allow user selection of ARM64_MODULE_PLTS
acpi/arm64: ignore 5.1 FADTs that are reported as 5.0
arm64: Allow selecting Pseudo-NMI again
...
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The only external user of fpsimd_save() and fpsimd_flush_cpu_state() is
the KVM FPSIMD code.
A following patch will introduce a mechanism to acquire owernship of the
FPSIMD/SVE context for performing context management operations. Rather
than having to export the new helpers to get/put the context, we can just
introduce a new function to combine fpsimd_save() and
fpsimd_flush_cpu_state().
This has also the advantage to remove any external call of fpsimd_save()
and fpsimd_flush_cpu_state(), so they can be turned static.
Lastly, the new function can also be used in the PM notifier.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The function sve_flush_cpu_state() has been removed in commit 21cdd7fd76e3
("KVM: arm64: Remove eager host SVE state saving").
So remove the associated prototype in asm/fpsimd.h.
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Currently the meanings of sve_vq_map and the ancillary helpers
__bit_to_vq() and __vq_to_bit() are not clearly explained.
This patch makes the explanatory comment clearer, and removes the
duplicate comment from fpsimd.h.
The WARN_ON() currently present in __bit_to_vq() confuses the
intended use of this helper. Since these are low-level helpers not
intended for general-purpose use anyway, it is better not to make
guesses about how these functions will be used: rather, this patch
removes the WARN_ON() and relies on callers to use the helpers
sensibly.
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
KVM will need to interrogate the set of SVE vector lengths
available on the system.
This patch exposes the relevant bits to the kernel, along with a
sve_vq_available() helper to check whether a particular vector
length is supported.
__vq_to_bit() and __bit_to_vq() are not intended for use outside
these functions: now that these are exposed outside fpsimd.c, they
are prefixed with __ in order to provide an extra hint that they
are not intended for general-purpose use.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: zhang.lei <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The current FPSIMD/SVE context handling support for non-task (i.e.,
KVM vcpu) contexts does not take SVE into account. This means that
only task contexts can safely use SVE at present.
In preparation for enabling KVM guests to use SVE, it is necessary
to keep track of SVE state for non-task contexts too.
This patch adds the necessary support, removing assumptions from
the context switch code about the location of the SVE context
storage.
When binding a vcpu context, its vector length is arbitrarily
specified as SVE_VL_MIN for now. In any case, because TIF_SVE is
presently cleared at vcpu context bind time, the specified vector
length will not be used for anything yet. In later patches TIF_SVE
will be set here as appropriate, and the appropriate maximum vector
length for the vcpu will be passed when binding.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Julien Grall <julien.grall@arm.com>
Tested-by: zhang.lei <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Due to the way the effective SVE vector length is controlled and
trapped at different exception levels, certain mismatches in the
sets of vector lengths supported by different physical CPUs in the
system may prevent straightforward virtualisation of SVE at parity
with the host.
This patch analyses the extent to which SVE can be virtualised
safely without interfering with migration of vcpus between physical
CPUs, and rejects late secondary CPUs that would erode the
situation further.
It is left up to KVM to decide what to do with this information.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Tested-by: zhang.lei <zhang.lei@jp.fujitsu.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In subsequent patches, we'll want to make use of sve_user_enable() and
sve_user_disable() outside of kernel/fpsimd.c. Let's move these to
<asm/fpsimd.h> where we can make use of them.
To avoid ifdeffery in sequences like:
if (system_supports_sve() && some_condition)
sve_user_disable();
... empty stubs are provided when support for SVE is not enabled. Note
that system_supports_sve() contains as IS_ENABLED(CONFIG_ARM64_SVE), so
the sve_user_disable() call should be optimized away entirely when
CONFIG_ARM64_SVE is not selected.
To ensure that this is the case, the stub definitions contain a
BUILD_BUG(), as we do for other stubs for which calls should always be
optimized away when the relevant config option is not selected.
At the same time, the include list of <asm/fpsimd.h> is sorted while
adding <asm/sysreg.h>.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
In order to make sve_save_state()/sve_load_state() more easily
reusable and to get rid of a potential branch on context switch
critical paths, this patch makes sve_pffr() inline and moves it to
fpsimd.h.
<asm/processor.h> must be included in fpsimd.h in order to make
this work, and this creates an #include cycle that is tricky to
avoid without modifying core code, due to the way the PR_SVE_*()
prctl helpers are included in the core prctl implementation.
Instead of breaking the cycle, this patch defers inclusion of
<asm/fpsimd.h> in <asm/processor.h> until the point where it is
actually needed: i.e., immediately before the prctl definitions.
No functional change.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Having read_zcr_features() inline in cpufeature.h results in that
header requiring #includes which make it hard to include
<asm/fpsimd.h> elsewhere without triggering header inclusion
cycles.
This is not a hot-path function and arguably should not be in
cpufeature.h in the first place, so this patch moves it to
fpsimd.c, compiled conditionally if CONFIG_ARM64_SVE=y.
This allows some SVE-related #includes to be dropped from
cpufeature.h, which will ease future maintenance.
A couple of missing #includes of <asm/fpsimd.h> are exposed by this
change under arch/arm64/. This patch adds the missing #includes as
necessary.
No functional change.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This patch refactors KVM to align the host and guest FPSIMD
save/restore logic with each other for arm64. This reduces the
number of redundant save/restore operations that must occur, and
reduces the common-case IRQ blackout time during guest exit storms
by saving the host state lazily and optimising away the need to
restore the host state before returning to the run loop.
Four hooks are defined in order to enable this:
* kvm_arch_vcpu_run_map_fp():
Called on PID change to map necessary bits of current to Hyp.
* kvm_arch_vcpu_load_fp():
Set up FP/SIMD for entering the KVM run loop (parse as
"vcpu_load fp").
* kvm_arch_vcpu_ctxsync_fp():
Get FP/SIMD into a safe state for re-enabling interrupts after a
guest exit back to the run loop.
For arm64 specifically, this involves updating the host kernel's
FPSIMD context tracking metadata so that kernel-mode NEON use
will cause the vcpu's FPSIMD state to be saved back correctly
into the vcpu struct. This must be done before re-enabling
interrupts because kernel-mode NEON may be used by softirqs.
* kvm_arch_vcpu_put_fp():
Save guest FP/SIMD state back to memory and dissociate from the
CPU ("vcpu_put fp").
Also, the arm64 FPSIMD context switch code is updated to enable it
to save back FPSIMD state for a vcpu, not just current. A few
helpers drive this:
* fpsimd_bind_state_to_cpu(struct user_fpsimd_state *fp):
mark this CPU as having context fp (which may belong to a vcpu)
currently loaded in its registers. This is the non-task
equivalent of the static function fpsimd_bind_to_cpu() in
fpsimd.c.
* task_fpsimd_save():
exported to allow KVM to save the guest's FPSIMD state back to
memory on exit from the run loop.
* fpsimd_flush_state():
invalidate any context's FPSIMD state that is currently loaded.
Used to disassociate the vcpu from the CPU regs on run loop exit.
These changes allow the run loop to enable interrupts (and thus
softirqs that may use kernel-mode NEON) without having to save the
guest's FPSIMD state eagerly.
Some new vcpu_arch fields are added to make all this work. Because
host FPSIMD state can now be saved back directly into current's
thread_struct as appropriate, host_cpu_context is no longer used
for preserving the FPSIMD state. However, it is still needed for
preserving other things such as the host's system registers. To
avoid ABI churn, the redundant storage space in host_cpu_context is
not removed for now.
arch/arm is not addressed by this patch and continues to use its
current save/restore logic. It could provide implementations of
the helpers later if desired.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In preparation for using a common representation of the FPSIMD
state for tasks and KVM vcpus, this patch separates out the "cpu"
field that is used to track the cpu on which the state was most
recently loaded.
This will allow common code to operate on task and vcpu contexts
without requiring the cpu field to be stored at the same offset
from the FPSIMD register data in both cases. This should avoid the
need for messing with the definition of those parts of struct
vcpu_arch that are exposed in the KVM user ABI.
The resulting change is also convenient for grouping and defining
the set of thread_struct fields that are supposed to be accessible
to copy_{to,from}_user(), which includes user_fpsimd_state but
should exclude the cpu field. This patch does not amend the
usercopy whitelist to match: that will be addressed in a subsequent
patch.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: inline fpsimd_flush_state for now]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
fpsimd.h uses the __init annotation, so pull in linux/init.h
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We issue the enable() call back for all CPU hwcaps capabilities
available on the system, on all the CPUs. So far we have ignored
the argument passed to the call back, which had a prototype to
accept a "void *" for use with on_each_cpu() and later with
stop_machine(). However, with commit 0a0d111d40fd1
("arm64: cpufeature: Pass capability structure to ->enable callback"),
there are some users of the argument who wants the matching capability
struct pointer where there are multiple matching criteria for a single
capability. Clean up the declaration of the call back to make it clear.
1) Renamed to cpu_enable(), to imply taking necessary actions on the
called CPU for the entry.
2) Pass const pointer to the capability, to allow the call back to
check the entry. (e.,g to check if any action is needed on the CPU)
3) We don't care about the result of the call back, turning this to
a void.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: James Morse <james.morse@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Dave Martin <dave.martin@arm.com>
[suzuki: convert more users, rename call back and drop results]
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
When refactoring the sigreturn code to handle SVE, I changed the
sigreturn implementation to store the new FPSIMD state from the
user sigframe into task_struct before reloading the state into the
CPU regs. This makes it easier to convert the data for SVE when
needed.
However, it turns out that the fpsimd_state structure passed into
fpsimd_update_current_state is not fully initialised, so assigning
the structure as a whole corrupts current->thread.fpsimd_state.cpu
with uninitialised data.
This means that if the garbage data written to .cpu happens to be a
valid cpu number, and the task is subsequently migrated to the cpu
identified by the that number, and then tries to enter userspace,
the CPU FPSIMD regs will be assumed to be correct for the task and
not reloaded as they should be. This can result in returning to
userspace with the FPSIMD registers containing data that is stale or
that belongs to another task or to the kernel.
Knowingly handing around a kernel structure that is incompletely
initialised with user data is a potential source of mistakes,
especially across source file boundaries. To help avoid a repeat
of this issue, this patch adapts the relevant internal API to hand
around the user-accessible subset only: struct user_fpsimd_state.
To avoid future surprises, this patch also converts all uses of
struct fpsimd_state that really only access the user subset, to use
struct user_fpsimd_state. A few missing consts are added to
function prototypes for good measure.
Thanks to Will for spotting the cause of the bug here.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Until KVM has full SVE support, guests must not be allowed to
execute SVE instructions.
This patch enables the necessary traps, and also ensures that the
traps are disabled again on exit from the guest so that the host
can still use SVE if it wants to.
On guest exit, high bits of the SVE Zn registers may have been
clobbered as a side-effect the execution of FPSIMD instructions in
the guest. The existing KVM host FPSIMD restore code is not
sufficient to restore these bits, so this patch explicitly marks
the CPU as not containing cached vector state for any task, thus
forcing a reload on the next return to userspace. This is an
interim measure, in advance of adding full SVE awareness to KVM.
This marking of cached vector state in the CPU as invalid is done
using __this_cpu_write(fpsimd_last_state, NULL) in fpsimd.c. Due
to the repeated use of this rather obscure operation, it makes
sense to factor it out as a separate helper with a clearer name.
This patch factors it out as fpsimd_flush_cpu_state(), and ports
all callers to use it.
As a side effect of this refactoring, a this_cpu_write() in
fpsimd_cpu_pm_notifier() is changed to __this_cpu_write(). This
should be fine, since cpu_pm_enter() is supposed to be called only
with interrupts disabled.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch adds two arm64-specific prctls, to permit userspace to
control its vector length:
* PR_SVE_SET_VL: set the thread's SVE vector length and vector
length inheritance mode.
* PR_SVE_GET_VL: get the same information.
Although these prctls resemble instruction set features in the SVE
architecture, they provide additional control: the vector length
inheritance mode is Linux-specific and nothing to do with the
architecture, and the architecture does not permit EL0 to set its
own vector length directly. Both can be used in portable tools
without requiring the use of SVE instructions.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
[will: Fixed up prctl constants to avoid clash with PDEATHSIG]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch defines and implements a new regset NT_ARM_SVE, which
describes a thread's SVE register state. This allows a debugger to
manipulate the SVE state, as well as being included in ELF
coredumps for post-mortem debugging.
Because the regset size and layout are dependent on the thread's
current vector length, it is not possible to define a C struct to
describe the regset contents as is done for existing regsets.
Instead, and for the same reasons, NT_ARM_SVE is based on the
freeform variable-layout approach used for the SVE signal frame.
Additionally, to reduce debug overhead when debugging threads that
might or might not have live SVE register state, NT_ARM_SVE may be
presented in one of two different formats: the old struct
user_fpsimd_state format is embedded for describing the state of a
thread with no live SVE state, whereas a new variable-layout
structure is embedded for describing live SVE state. This avoids a
debugger needing to poll NT_PRFPREG in addition to NT_ARM_SVE, and
allows existing userspace code to handle the non-SVE case without
too much modification.
For this to work, NT_ARM_SVE is defined with a fixed-format header
of type struct user_sve_header, which the recipient can use to
figure out the content, size and layout of the reset of the regset.
Accessor macros are defined to allow the vector-length-dependent
parts of the regset to be manipulated.
Signed-off-by: Alan Hayward <alan.hayward@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Okamoto Takayuki <tokamoto@jp.fujitsu.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch uses the cpufeatures framework to determine common SVE
capabilities and vector lengths, and configures the runtime SVE
support code appropriately.
ZCR_ELx is not really a feature register, but it is convenient to
use it as a template for recording the maximum vector length
supported by a CPU, using the LEN field. This field is similar to
a feature field in that it is a contiguous bitfield for which we
want to determine the minimum system-wide value. This patch adds
ZCR as a pseudo-register in cpuinfo/cpufeatures, with appropriate
custom code to populate it. Finding the minimum supported value of
the LEN field is left to the cpufeatures framework in the usual
way.
The meaning of ID_AA64ZFR0_EL1 is not architecturally defined yet,
so for now we just require it to be zero.
Note that much of this code is dormant and SVE still won't be used
yet, since system_supports_sve() remains hardwired to false.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This patch implements the core logic for changing a task's vector
length on request from userspace. This will be used by the ptrace
and prctl frontends that are implemented in later patches.
The SVE architecture permits, but does not require, implementations
to support vector lengths that are not a power of two. To handle
this, logic is added to check a requested vector length against a
possibly sparse bitmap of available vector lengths at runtime, so
that the best supported value can be chosen.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
