| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is no "no-emmc" property, so intention for SD/SDIO only nodes was
to use "no-mmc":
qcom/sa8155p-adp.dtb: mmc@8804000: Unevaluated properties are not allowed ('no-emmc' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221204094438.73288-3-krzysztof.kozlowski@linaro.org
|
|
When recently adding the missing 'regulator-allowed-modes' properties it
appears that the binding example with its four-spaces indentation
(corresponding to a single tab, which is still to little) was copied
verbatim.
Drop the unnecessary first line break after 'regulator-allowed-modes'
properties and indent the single remaining continuation line properly.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221116102054.4673-3-johan+linaro@kernel.org
|
|
Mergeback arm64-fixes-for-6.1 to avoid merge conflicts.
|
|
This board uses RPMH, specifies "regulator-allow-set-load" for LDOs,
but doesn't specify any modes with "regulator-allowed-modes".
Prior to commit efb0cb50c427 ("regulator: qcom-rpmh: Implement
get_optimum_mode(), not set_load()") the above meant that we were able
to set either LPM or HPM mode. After that commit (and fixes [1]) we'll
be stuck at the initial mode. Discussion of this has resulted in the
decision that the old dts files were wrong and should be fixed to
fully restore old functionality.
Let's re-enable the old functionality by fixing the dts.
NOTE: while here, let's also remove the nonsensical
"regulator-allow-set-load" on the fixed regulator "vreg_s4a_1p8".
[1] https://lore.kernel.org/r/20220824142229.RFT.v2.2.I6f77860e5cd98bf5c67208fa9edda4a08847c304@changeid
Fixes: 5b85e8f2225c ("arm64: dts: qcom: sa8155p-adp: Add base dts file")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220829094903.v2.1.Id59c32b560c4662d8b3697de2bd494d08d654806@changeid
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221006144518.256956-1-krzysztof.kozlowski@linaro.org
|
|
The 'snps,ptp-ref-clk-rate' and 'snps,ptp-req-clk-rate' properties
are not supported by the stmmac driver currently, so remove
them from the sa8155p-adp ethernet node as well.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220907204153.2039776-1-bhupesh.sharma@linaro.org
|
|
Fix the issues seen with ethernet traffic getting stalled on SA8155p-ADP
board with default (or larger) mtu size of 1500 bytes, by disabling
multiple Tx and Rx queues for the stmmac IP block.
With the single queue setup, the ethernet traffic is stable,
wget / curl can work well on the board and no ethernet stall is
observed even when longer netperf / iperf3 test are run. Also
a performance of ~940 Mbits/sec is observed on the 1G link, so
there is no observable degradation in performance as well.
Fixes: c5cb42cc8411 ("arm64: dts: qcom: sa8155p-adp: Enable ethernet node")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220423195003.353150-1-bhupesh.sharma@linaro.org
|
|
Enable the ethernet node, add the phy node and pinctrl for ethernet.
[bhsharma: Correct ethernet/rgmii related pinmuxs, specify multi-queues and
plug in the PHY interrupt for WOL]
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220325163537.1579969-3-bhupesh.sharma@linaro.org
|
|
Add support for uSD card on SA8155p-ADP board using the SDHC2
interface.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220403144151.92572-3-bhupesh.sharma@linaro.org
|
|
SA8155p ADP board supports the PCIe0 controller in the RC
mode (only). So add the support for the same.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220326055754.1796146-3-bhupesh.sharma@linaro.org
|
|
The following properties are not supported and causing dtbs_check
warnings.
- vdda-phy-max-microamp
- vdda-pll-max-microamp
- vddp-ref-clk-max-microamp
- vddp-ref-clk-always-on
Drop them from QMP PHY nodes.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210929034253.24570-6-shawn.guo@linaro.org
|
|
Enable two of the remoteprocs found on SA8155p platform - 'audio and
compute'. Also specify firmware path for them.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928140929.2549459-3-bhupesh.sharma@linaro.org
|
|
SA8155p adp board has two USB A-type receptacles called
USB-portB and USB-portC respectively.
While USB-portB is a USB High-Speed connector/interface, the
USB-portC one is a USB 3.1 Super-Speed connector/interface.
Also the USB-portB is used as the USB emergency
download port (for image download purposes).
Enable both the ports on the board in USB Host mode (since all
the USB interfaces are brought out to USB Type A
connectors).
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210627114616.717101-4-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add base DTS file for SA8155p Automotive Development Platform.
It enables boot to console, adds tlmm reserved range and ufs flash.
It also includes pmic file.
SA8155p-adp board is based on sa8155p Qualcomm Snapdragon SoC.
SA8155p platform is similar to the SM8150, so use this as base
for now.
Cc: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210617054548.353293-6-bhupesh.sharma@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
