summaryrefslogtreecommitdiff
path: root/arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi
AgeCommit message (Collapse)AuthorFilesLines
2017-09-05ARM64: dts: meson: add mmc clk gate pinsJerome Brunet1-3/+6
Add the pinctrl to switch mmc clk pins in gpio (pulled down) mode. This is necessary to be able to gate the clk outside of the SoC while keeping it running in the controller Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-09-05ARM64: dts: meson: remove cap-sd-highspeed from emmc nodesJerome Brunet1-1/+0
It does not make much sense to define cap-sd-highspeed in the emmc nodes Just remove it. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-05-17arm64: dts: meson-gxbb-vega-s95: Fix node orderAndreas Färber1-27/+27
Sort nodes referenced by label alphabetically. Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-05-17arm64: dts: meson-gxbb-vega-s95: Fix Wifi node nameAndreas Färber1-1/+1
bcrmf -> brcmf -> wifi Fixes: ab5b24fdd2d5 ("ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodes") Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06ARM64: dts: amlogic: add the ethernet TX delay configurationMartin Blumenstingl1-0/+2
This adds the amlogic,tx-delay-ns property with the old (hardcoded) default value of 2ns to all boards which are using an RGMII ethernet PHY. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIOMartin Blumenstingl1-1/+18
This resets the ethernet PHY during boot to get the PHY into a "clean" state. While here also specify the phy-handle of the ethmac node to make the PHY configuration similar to the one we have on GXL devices. This will allow us to specify OF-properties for the PHY itself. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-01-19ARM64: dts: meson-gxbb-vega-s95: Add LEDAndreas Färber1-0/+11
There is one blue LED on the front of the device. Keep it lit and configure it as panic indicator. Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-11-15ARM64: dts: meson-gxbb-vega-s95: Add SD/SDIO/MMC and PWM nodesMartin Blumenstingl1-0/+104
All boards from the Tronsmart Vega S95 series are sharing similar MMC based hardware. sd_emmc_a is used to connect a Broadcom based SDIO wifi card (supported by the brcmfmac driver). The 32.768KHz LPO clock for the wifi chip is generated by PWM_E. sd_emmc_b is routed to the SD-card. Unlike p20x there is no GPIO regulator, meaning it only supports 3.3V (which seems to be hard-wired). The eMMC chip is connected to sd_emmc_c and is implemented similar to the meson-gxbb-p20x boards (meaning that hard-wired fixed regulators are used). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-10-18ARM64: dts: meson-gxbb: Add rmii pinctrl node and rename rgmii nodeNeil Armstrong1-1/+1
For boards only supporting 10/100 ethernet over a RMII PHY link, add a separate pinctrl node. By the way, rename the existing node to rgmii specific naming in all boards dts. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-09-16ARM64: dts: meson-gxbb-vega-s95: Enable USB NodesMartin Blumenstingl1-0/+30
Enable both gxbb USB controller and add a 5V regulator for the OTG port VBUS Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-09-14ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devicesMartin Blumenstingl1-0/+6
All of these have a Realtek Gbit RGMII PHY. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-09-02ARM64: dts: meson-gxbb: Enable the the IR decoder on supported boardsMartin Blumenstingl1-0/+6
Enable the Infrared Remote Controller on boards which have an Infrared receiver. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-06-01ARM64: dts: amlogic: Enable pin controller on GXBB-based platformsCarlo Caione1-0/+3
Update DTS and DTSI files to enable the pin controller. We also now support the blinking blue LED on the Odroid-C2. Signed-off-by: Carlo Caione <carlo@endlessm.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-03-30ARM64: dts: amlogic: update serial aliasesKevin Hilman1-0/+4
Apparently, it's not valid to have an alias point to a disabled device. Fix this by moving the aliases that are used (serial0) into the files that use them, and remove aliases to disabled devices (serial1). Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
2016-03-07ARM64: dts: amlogic: Add Tronsmart Vega S95 configsAndreas Färber1-0/+55
Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes. Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Carlo Caione <carlo@endlessm.com>
generated by cgit v1.2.3 (git 2.39.0) at 2025-08-30 20:10:48 +0300