| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
|
|
When targetting ARCH_MULTIPLATFORM, we may include support for SoCs with
PCI-capable devices (e.g. mach-virt with virtio-pci).
This patch allows PCI support to be selected for these SoCs by selecting
CONFIG_MIGHT_HAVE_PCI when CONFIG_ARCH_MULTIPLATFORM=y and removes the
individual selections from multi-platform enabled SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
Merge "ARM: tegra: core code changes for 3.16" from Stephen Warren:
This branch contains just a single patch this time around. Thierry
enhanced Tegra's restart code to allow programming PMC scratch registers
to request specific behaviour after reboot. One of the most useful
options for mainline software is the ability to reboot directly into USB
recovery mode, which e.g. allows the bootloader to be reflashed.
* tag 'tegra-for-3.16-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Support reboot modes
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The boot ROM on Tegra SoCs supports booting into forced recovery mode
(RCM) by setting a bit in the PMC scratch register 0. Similarily, the
Android bootloader examines some of the bits in this register to disable
autoboot or enter recovery mode.
Support these modes by setting the corresponding bits depending on the
specified reboot command (forced-recovery, bootloader, recovery). Recent
systemd-based distributions allow this to be specified using an optional
argument to the reboot command.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Commit a7cbe92cef27 ("ARM: tegra: remove tegra EMC scaling driver")
removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig
entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"Lots of changes specific to one of the SoC families. Some that stick
out are:
- mach-qcom gains new features, most importantly SMP support for the
newer chips (Stephen Boyd, Rohit Vaswani)
- mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
- SMP support for Rockchips (Heiko Stübner)
- Lots of i.MX changes (Shawn Guo)
- Added support for BCM5301x SoC (Hauke Mehrtens)
- Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
and Sebastian Hesselbarth doing the final part of a long journey)
- Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
Bergmann)"
* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
ARM: cache-tauros2: remove ARMv6 code
ARM: mvebu: don't select CONFIG_NEON
ARM: davinci: fix DT booting with default defconfig
ARM: configs: bcm_defconfig: enable bcm590xx regulator support
ARM: davinci: remove tnetv107x support
MAINTAINERS: Update ARM STi maintainers
ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
ARM: bcm21664: Add board support.
ARM: sunxi: Add the new watchog compatibles to the reboot code
ARM: enable ARM_HAS_SG_CHAIN for multiplatform
ARM: davinci: remove da8xx_omapl_defconfig
ARM: davinci: da8xx: fix multiple watchdog device registration
ARM: davinci: add da8xx specific configs to davinci_all_defconfig
ARM: davinci: enable da8xx build concurrently with older devices
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
ARM: shmobile: APMU: Fix warnings due to improper printk formats
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
Merge "ARM: tegra: core SoC changes for 3.15" from Stephen Warren:
A couple of minor fixes, plus the removal of the EMC scaling driver,
which hasn't been active since we converted clocks to device tree.
* tag 'tegra-for-3.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Export I/O rail functions
ARM: tegra: remove tegra EMC scaling driver
ARM: tegra: don't timeout if CPU is powergated
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
Merge "ARM: tegra: Trusted Foundations work for 3.15" from Stephen Warren:
This pull request contains a number of cleanups and enhancements for the
Trusted Foundations firmware used on production Tegra SoCs. The changes
allow kernels without TF support to run on HW that uses TF, albeit with
reduced functionality, and also fix the cpuidle feature.
* tag 'tegra-for-3.15-tf' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cpuidle: use firmware for power down
ARM: trusted_foundations: implement prepare_idle()
ARM: firmware: add prepare_idle() operation
ARM: firmware: enable Trusted Foundations by default
ARM: trusted_foundations: fallback when TF support is missing
ARM: trusted_foundations: fix vendor prefix typos
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
- Remove common kconfig options required by multi-platform builds out
of individual platforms as they are redundant.
- Make SMP, CACHE_L2X0 and GPIO config options user visible on
multi-platform builds as most platforms enable these options and all
platforms can run with them enabled.
- Make multi-platform v6 default to more optimal v6k rather than v6
- Remove the last bit of mach-virt and convert it to just a kconfig
option.
Conflicts:
arch/arm/mach-omap2/Kconfig
|
|
The I/O rail functions can be used by drivers that are buildable as
modules. Exporting the functions makes sure that they're available.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Nothing calls into the Tegra EMC (External Memory Controller) scaling
driver any more, so it's dead code. Remove it.
Cc: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
|
|
Many V6 and V7 platforms have an L2x0 cache, so make
CONFIG_MIGHT_HAVE_CACHE_L2X0 visible for V6 and V7 multi-platform
builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
All V7 platforms can run SMP kernels, so make CONFIG_SMP visible for V7
multi-platform builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Multi-platform requires various kconfig options to be selected, so
platforms don't need to select them individually.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix tegra_init_cache() to check whether the system has a PL310 cache
before touching the PL310 registers. This prevents access to non-existent
registers on Tegra114 and later.
Note for stable kernels:
In <= v3.12, the file to patch is arch/arm/mach-tegra/common.c.
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Attempt to invoke the prepare_idle() and do_idle() firmware calls
to power down a CPU so an underlying firmware gets informed of
the idle operation and performs it by itself if designed in such a way.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
USB_ARCH_HAS_EHCI, USB_ARCH_HAS_OHCI, and USB_ARCH_HAS_XHCI were just
removed. Selecting them is a nop. The select statements for these
symbols can be removed too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When booting secondary CPU(s) which are not yet powergated, a wrong
check lead to a timeout after 100 jiffies. With this patch, we only
delay powergating if CPUs are still not powered yet.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
arch/arm/mach-tegra/pm.c, kernel/power/console.c and mm/vmpressure.c
were somehow getting slab.h indirectly through cgroup.h which in turn
was getting it indirectly through xattr.h. A scheduled cgroup change
drops xattr.h inclusion from cgroup.h and breaks compilation of these
three files. Add explicit slab.h includes to the three files.
A pending cgroup patch depends on this change and it'd be great if
this can be routed through cgroup/for-3.14-fixes branch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-tegra@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: cgroups@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
From Stephen Warren:
ARM: tegra: SoC-specific core code changes
This branch contains various miscellaneous changes to code in the
mach-tegra/ directory. It is baased on v3.13-rc1, and shouldn't conflict
with anything else.
* tag 'tegra-for-3.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: select PINCTRL_TEGRA124 for Tegra124 SoC
ARM: tegra: use section-sized static mappings for LPAE too
ARM: tegra: don't hard-code DEBUG_LL baud rate
ARM: tegra: fix DEBUG_LL combined with LPAE
ARM: tegra: switch FUSE clock on before usage
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
From Stephen Warren:
ARM: tegra: Trusted Foundations firmware support
Add support for the Trusted Foundations secure-mode firmware, as found
on NVIDIA SHIELD. This allows Linux to run in non-secure mode on this
board; all previous Tegra support has assumed the kernel is running in
secure mode.
(The base TF support has been discussed back and forth a lot; for now
the most logical place for it seems to be under arch/arm, so we're adding
it here. We can move it out to a common location in the future if needed).
* tag 'tegra-for-3.14-trusted-foundations' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: support Trusted Foundations by default
ARM: tegra: set CPU reset handler using firmware
ARM: tegra: split setting of CPU reset handler
ARM: tegra: add support for Trusted Foundations
of: add Trusted Foundations bindings documentation
of: add vendor prefix for Trusted Logic Mobility
ARM: add basic support for Trusted Foundations
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
From Stephen Warren:
ARM: tegra: powergate driver changes
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
* tag 'tegra-for-3.14-powergate' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add IO rail support
ARM: tegra: Special-case the 3D clamps on Tegra124
ARM: tegra: Add Tegra124 powergate support
ARM: tegra: Export tegra_powergate_remove_clamping()
ARM: tegra: Export tegra_powergate_power_off()
ARM: tegra: Rename cpu0 powergate to crail
ARM: tegra: Fix some whitespace oddities
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Bringing in the tegra dma/reset rework as a base for new SoC branches.
* tegra/dma-reset-rework: (81 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add tegra_io_rail_power_off() and tegra_io_rail_power_on() functions to
put IO rails into or out of deep powerdown mode, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
A separate register is used to remove the clamps for the GPU on
Tegra124. In order to be able to use the same API, special-case
this particular partition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Three new gates have been added for Tegra124: SOR, VIC and IRAM. In
addition, PCIe and SATA gates are again supported, like on Tegra20 and
Tegra30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Drivers can use the tegra_powergate_remove_clamping() API during
initialization. In order to allow such drivers to be built as modules,
export the symbol.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This function can be used by drivers, which in turn may be built as
modules. Export the symbol so it is available to modules.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This matches the name of the powergate as listed in the TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Some of the powergate code uses unusual spacing around == and has a tab
instead of a space before an opening parenthesis.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use a firmware operation to set the CPU reset handler and only resort to
doing it ourselves if there is none defined.
This supports the booting of secondary CPUs on devices using a TrustZone
secure monitor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Not all Tegra devices can set the CPU reset handler in the same way.
In particular, devices using a TrustZone secure monitor cannot set it
up directly and need to ask the firmware to do it.
This patch separates the act of setting the reset handler from its
preparation, so the former can be implemented in a different way.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Register the firmware operations for Trusted Foundations if the device
tree indicates it is active on the device.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The pincontrol driver for Tegra124 is build through config
PINCTRL_TEGRA124. Select this config option whenever Tegra124
SoC is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Add a missing break to the switch in tegra_init_fuse() which determines
which SoC the code is running on. This prevents the Tegra30+ fuse
handling code from running on Tegra20.
Fixes: 3bd1ae57f7bb ("ARM: tegra: add fuses as device randomness")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra clock driver is built unconditionally when Tegra support is
enabled. In order to avoid having to ifdef the forthcoming reset driver
implementation, have ARCH_TEGRA select RESET_CONTROLLER.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
This makes it possible to request the gpio descriptors in
rfkill_gpio driver regardless of the platform.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The static mappings for Tegra's PPSB and APB regions were sized at 1MB
in order to allow mapping via sections in order to avoid burning RAM for
PTEs. On LPAE, sections are 2MB, so the static mappings need to be
larger in order to gain the same benefit. Set IO_{PPSB,APB}_SIZE to
SECTION_SIZE so this adjusts automatically.
While we're fiddling with iomap.h, compress IO_{IRAM,CPU}_VIRT together
to save virtual address space in the vmalloc region; these two regions
are mapped using PTEs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
Stop writing to the UART clock divider registers in the Tegra DEBUG_LL
code. This allows the DEBUG_LL output to use whatever baud rate was set
up by the bootloader. Some users are using higher rates than 115200.
This removes the only usage of tegra_uart_config[3], so reduce the size
allocated for that array.
Finally, fix busyuart() so that it only waits for THRE and not TEMT. For
some reason, TEMT doesn't get asserted (at least on Tegra30 Beaver) at
9600 baud, even though it does at 115200 baud. This sounds like a HW bug,
but I haven't investigated. For reference, U-Boot's serial code has
always only checked THRE, and not checked TEMT.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
|
|
FUSE clock is enabled by most bootloaders, but we cannot expect it to be
on in all contexts (e.g. kexec).
Ensure the FUSE clock is enabled before any of its registers is touched.
Since FUSE is touched very early during system boot (before the clock
devices are registered), directly manipulate the clock register bit in
case the clock device cannot be acquired.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
