| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.3" from Simon Horman
* Add Add CPG/MSTP Clock Domain for sound on r8a779[01] SoCs.
This allows sound to work once again.
* tag 'renesas-fixes-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain for sound
ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain for sound
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.3" from Maxime Ripard:
Two patches, one that fixes one of the DT build, and the other raising the
voltage of the lowest OPP of the A20 to remain within the SoC operating
boundaries
* tag 'sunxi-fixes-for-4.3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: Fix Makefile target for sun4i-a10-itead-iteaduino-plus
ARM: dts: sunxi: Raise minimum CPU voltage for sun7i-a20 to meet SoC specifications
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fixes for v4.3" from Kukjin Kim:
- fix invalid clock used for FIMD IOMMU
- fix thermal boot issue smdk5250-smdk5250
- fix S2R on exynos4412 trats2 boards
- fix LEDs on exynos5422-odroidxu3-common
- fix booting of all 8 cores on exynos542x
* tag 'samsung-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Fix wrong clock binding for sysmmu_fimd1_1 on exynos5420
ARM: dts: Fix bootup thermal issue on smdk5250
ARM: dts: add suspend opp to exynos4412
ARM: dts: Fix LEDs on exynos5422-odroidxu3
ARM: EXYNOS: reset Little cores when cpu is up
|
|
v4.3-samsung-fixes
Fixes for Exynos (DT and mach code):
1. Finally fix booting of all 8 cores on Exynos Octa (Exynos542x): all
8 cores are booting and can be used. The fix, based on vendor
code and bootloader behavior, is as for time being only
for MCPM enabled path.
2. Fix thermal boot issue on SMDK5250.
3. Fix invalid clock used for FIMD IOMMU.
|
|
The sysmmu_fimd1_1 should bind the clock CLK_SMMU_FIMD1M1, not the clock
CLK_SMMU_FIMD1M0. CLK_SMMU_FIMD1M0 is a clock for the sysmmu_fimd1_0.
This wrong clock binding causes the problem that is blocked in iommu_map
function when IOMMU is enabled and exynos-drm driver tries to allocate
buffer via DMA mapping API on Odroid-XU3 board.
Fixes: b70045167815 ("ARM: dts: add sysmmu nodes for exynos5420")
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: <stable@vger.kernel.org> # v4.2
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
With default config on smdk5250 latest tree throws below message:
[ 2.226049] thermal thermal_zone0: critical temperature reached(224 C),shutting down
[ 2.227840] reboot: Failed to start orderly shutdown: forcing the issue
and hangs randomly because it reads wrong temperature value.
I can't figure out any direct relation between LDO10 and TMU from board
schematics which I have. So making LDO10 always-on to fix issue for now.
Signed-off-by: Yadwinder Singh Brar <yadi.brar01@gmail.com>
[pankaj.dubey: resubmitted after rebasing to latest kgene tree]
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
797a0626e08c ("ARM: shmobile: r8a7791 dtsi: Add CPG/MSTP Clock Domain")
added CPG/MSTP clock-cells domain support, but it was missing sound
support. This patch adds it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: updated commit id referred to in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
484adb005886 ("ARM: shmobile: r8a7790 dtsi: Add CPG/MSTP Clock Domain")
added CPG/MSTP clock-cells domain support, but it was missing sound
support. This patch adds it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms: Updated commit id referred to in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.3:
- One fix for i.MX6 Rex Pro board to remove a duplicated pinctrl entry
which causes error for USB pinctrl setup.
- Fix MC34708 PMIC interrupt level for imx53-qsrb board.
* tag 'imx-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: fix usb pin control for imx-rex dts
ARM: imx53: qsrb: fix PMIC interrupt level
ARM: imx53: include IRQ dt-bindings header
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.3-rc cycle:
- Two more patches to fix most of the MMC regressions with the
PBIAS regulator changes. At least two MMC driver related issues
still seems to remain for omap3 legacy booting and omap4 duovero.
Note that the dts changes depend on a recent regulator fix, and
are based on the regulator commit now in mainline kernel
- Enable autoidle for am43xx clocks to prevent clocks from staying
always on
- Fix i2c5 pinctrl offsets for omap5-uevm
- Enable PCA953X as that's needed for HDMI to work on omap5
- Update phy supplies for beagle x15 beta board
- Use palmas-usb for on beagle x15 to start using the related
driver that recently got merged
* tag 'omap-for-v4.3/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: fix omap2+ address translation for pbias
ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2
ARM: omap2plus_defconfig: enable GPIO_PCA953X
ARM: dts: omap5-uevm.dts: fix i2c5 pinctrl offsets
ARM: OMAP2+: AM43XX: Enable autoidle for clks in am43xx_init_late
ARM: dts: am57xx-beagle-x15: Update Phy supplies
regulator: pbias: program pbias register offset in pbias driver
ARM: omap2plus_defconfig: Enable MUSB DMA support
ARM: DRA752: Add ID detect for ES2.0
ARM: OMAP3: vc: fix 'or' always true warning
ARM: OMAP2+: Fix booting if no timer parent clock is available
ARM: OMAP2+: omap-device: fix race deferred probe of omap_hsmmc vs omap_device_late_init
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Add the ddc-i2c-bus reference to the veyron hdmi nodes,
so that they can read the edid of connected displays.
* tag 'v4.3-rockchip32-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: Add ddc i2c reference to veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
STI drm drivers probe and bind using component framework was incorrect.
In addition to drivers fix DT update is needed to make all sub-components
become childs of sti-display-subsystem.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
"ARM: dts: <omap2/omap4/omap5/dra7>: add minimal l4 bus
layout with control module support" moved pbias_regulator dt node
from being a child node of ocp to be the child node of
'syscon'. Since 'syscon' doesn't have the 'ranges' property,
address translation fails while trying to convert the address
to resource. Fix it here by populating 'ranges' property in
syscon dt node.
Fixes: 72b10ac00eb1 ("ARM: dts: omap24xx: add minimal l4 bus
layout with control module support")
Fixes: 7415b0b4c645 ("ARM: dts: omap4: add minimal l4 bus layout
with control module support")
Fixes: ed8509edddeb ("ARM: dts: omap5: add minimal l4 bus
layout with control module support")
Fixes: d919501feffa ("ARM: dts: dra7: add minimal l4 bus
layout with control module support")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: fixed omap3 pbias to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This fixes a duplicated pin control causing this error:
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by regulators:regulator@2; cannot claim for 2184000.usb
imx6q-pinctrl 20e0000.iomuxc: pin-137 (2184000.usb) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp on device 20e0000.iomuxc
imx_usb 2184000.usb: Error applying setting, reverse things
back
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_EIM_D31 already
requested by regulators:regulator@1; cannot claim for 2184200.usb
imx6q-pinctrl 20e0000.iomuxc: pin-52 (2184200.usb) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 52 (MX6Q_PAD_EIM_D31)
from group usbh1grp on device 20e0000.iomuxc
imx_usb 2184200.usb: Error applying setting, reverse things
back
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Fixes: e2047e33f2bd ("ARM: dts: add initial Rex Pro board support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The MC34708 PMIC interrupt level is active high, but was set to
active low in the devicetree, probably as a result of a copy and
paste error from the QSB board.
This caused IRQ storms and led to the kernel disabling the PMIC
interrupt.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Allows to use the more meaningful IRQ flag defines instead of
the raw values.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The VBUS line of USB2 is connected to VBUS detect logic on
the PMIC. Use the palmas-usb driver to report VBUS events
to the USB driver.
As the palmas-usb driver supports GPIO based ID reporting
provide the GPIO for ID pin as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The i2c5 pinctrl offsets are wrong. If the bootloader doesn't set the
pins up, communication with tca6424a doesn't work (controller timeouts)
and it is not possible to enable HDMI.
Fixes: 9be495c42609 ("ARM: dts: omap5-evm: Add I2c pinctrl data")
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Originally, all the SoC PHY rails were supplied by LDO3. However, as a
result of characterization, it was determined that this posed a risk in
extreme load conditions. Hence the PHY rails are split between two
different LDOs. Update the related node as a result
LDO3/VDDA_1V8_PHYA supplies vdda_usb1, vdda_usb2, vdda_sata, vdda_usb3
LDO4/VDDA_1V8_PHYB supplies vdda_pcie1, vdda_pcie0, vdda_hdmi, vdda_pcie
NOTE: We break compatibility with pre-production boards with this change
since, the PMIC LDO4 is disabled at OTP level.
The new configuration is the plan of record and all pre-production
boards are supposed to be replaced with the latest boards matching the
mentioned configuration.
Some very few 10 something boards have been created and
stopped production till the latest modifications were done (PMIC USB
interrupt, LDO4 etc) - and all of those boards are now getting
scrapped.. If there are any (as per tracking information, there should
not be any), TI should be contacted to have them replaced.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated commit about these being TI internal protos]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Mark 800MHz OPP as a suspend opp for Exynos4412 based
boards so effectively cpufreq-dt driver behavior w.r.t.
suspend frequency matches what the old exynos-cpufreq
driver has been doing.
This patch fixes suspend/resume support on Exynos4412 based
Trats2 board and reboot hang on Exynos4412 based Odroid U3
board.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
The LEDs on Odroid XU3 family boards could not properly probe
because PWM outputs were reduced only to PWM for fan. Fix it
for Odroid XU3 and XU3-Lite boards by switching to usage of
all 4 outputs (although the PWM for MIPI probably is redundant
because board does not have MIPI connector available).
This fixes warnings on dmesg:
[ 4.838712] samsung-pwm 12dd0000.pwm: tried to request PWM channel 1 without output
[ 4.838725] leds_pwm pwmleds: unable to request PWM for green:mmc0: -22
[ 4.838767] leds_pwm: probe of pwmleds failed with error -22
Fixes: b685d540cc26 ("ARM: dts: Add pwm-fan node for exynos5422-odroidxu3")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This fix the model name for the device.
Whole string taken from the HP support center web page
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Register address in name of the node is wrong
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use platform specific compatible strings instead of the common
"ti,pbias-omap" compatible string.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Only the IGEPv2 boards have a LAN9221i chip connected to the GPMC
so the pinmux configuration for the GPIO connected to the IRQ line
of the LAN chip should not be defined in the IGEP common dtsi but
in the one common to the IGEPv2 boards.
While there, use the OMAP3_CORE1_IOPAD() macro for the padconf reg.
Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the support in the generic PM framework for wakeirq and capability
added to the rtc-ds1307 driver to support this, we can now define the
optional wakeup irq to allow the RTC to wakeup the system from low power
modes as part of suspend.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix the mpu voltage as it is set too low for the silicon
revision 2.1.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For beagle x15, both the vdd and io lines are connected to the
same regulator (ldo1_reg). However vmmc_aux is populated to vdd_3v3.
Remove it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like I made a typo on the control base, all the 81xx
SoCs have it at 0x48140000 base. We've just gotten away with
the typo as the Ethernet phy was configured by the bootloader
on my test system and we're not yet using the pinctrl.
In addition to fixing the contol base, we need to also use the
right Ethernet phy flags to initialize it. And we are still
missing the PLL driver for dm814x and only relying on the
divider and mux clocks.
Fixes: f3d953ea3721 ("ARM: dts: Add minimal dm814x support")
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Let's fix pinmux address of gpio 170 used by tfp410 powerdown-gpio.
According to the OMAP35x Technical Reference Manual
CONTROL_PADCONF_I2C3_SDA[15:0] 0x480021C4 mode0: i2c3_sda
CONTROL_PADCONF_I2C3_SDA[31:16] 0x480021C4 mode4: gpio_170
the pinmux address of gpio 170 must be 0x480021C6.
The former wrong address broke i2c3 (used by hdmi ddc), resulting in
kernel message:
omap_i2c 48060000.i2c: controller timed out
Fixes: 8cecf52befd7 ("ARM: omap3-beagle.dts: add display information")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Carl Frederik Werner <frederik@cfbw.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ddc-i2c-bus property was missing from the veyron dtsi file since
downstream the ddc-i2c-bus was still being specified in rk3288.dtsi and
nobody noticed when the veyron dtsi was sent upstream. Add it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Commit 79ae3e66f8d (ARM: dts: sun4i: Add Iteaduino Plus A10) added a new
make target for the sun4i-a10-itead-iteaduino-plus dts file, but mistakenly
used .dts instead of the correct .dtb suffix. This resulted in a build error
like:
scripts/Makefile.dtbinst:42: target 'sun4i-a10-itead-iteaduino-plus.dts' doesn't match the target pattern
when doing a make dtbs_install.
Fix it to use the proper file name.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
specifications
sun7i-a20.dtsi contains a cpufreq operating point at 0.9 volts. The minimum
CPU voltage for the Allwinner A20 SoC, however, is 1.0 volts. Thus, raise
the voltage for the lowest operating point to 1.0 volts in order to stay
within the SoC specifications. It is an undervolted setting that isn't
stable across all SoCs and boards out there.
Cc: <stable@vger.kernel.org> # v4.0+
Fixes: d96b7161916f ("ARM: dts: sun7i: Add cpu clock reference and operating points to dtsi")
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Acked-by: Iain Paton <ipaton0@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Merge third patch-bomb from Andrew Morton:
- even more of the rest of MM
- lib/ updates
- checkpatch updates
- small changes to a few scruffy filesystems
- kmod fixes/cleanups
- kexec updates
- a dma-mapping cleanup series from hch
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (81 commits)
dma-mapping: consolidate dma_set_mask
dma-mapping: consolidate dma_supported
dma-mapping: cosolidate dma_mapping_error
dma-mapping: consolidate dma_{alloc,free}_noncoherent
dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}
mm: use vma_is_anonymous() in create_huge_pmd() and wp_huge_pmd()
mm: make sure all file VMAs have ->vm_ops set
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
mm: mark most vm_operations_struct const
namei: fix warning while make xmldocs caused by namei.c
ipc: convert invalid scenarios to use WARN_ON
zlib_deflate/deftree: remove bi_reverse()
lib/decompress_unlzma: Do a NULL check for pointer
lib/decompressors: use real out buf size for gunzip with kernel
fs/affs: make root lookup from blkdev logical size
sysctl: fix int -> unsigned long assignments in INT_MIN case
kexec: export KERNEL_IMAGE_SIZE to vmcoreinfo
kexec: align crash_notes allocation to make it be inside one physical page
kexec: remove unnecessary test in kimage_alloc_crash_control_pages()
kexec: split kexec_load syscall from kexec core code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
|
|
When loading x86 64bit kernel above 4GiB with patched grub2, got kernel
gunzip error.
| early console in decompress_kernel
| decompress_kernel:
| input: [0x807f2143b4-0x807ff61aee]
| output: [0x807cc00000-0x807f3ea29b] 0x027ea29c: output_len
| boot via startup_64
| KASLR using RDTSC...
| new output: [0x46fe000000-0x470138cfff] 0x0338d000: output_run_size
| decompress: [0x46fe000000-0x47007ea29b] <=== [0x807f2143b4-0x807ff61aee]
|
| Decompressing Linux... gz...
|
| uncompression error
|
| -- System halted
the new buffer is at 0x46fe000000ULL, decompressor_gzip is using
0xffffffb901ffffff as out_len. gunzip in lib/zlib_inflate/inflate.c cap
that len to 0x01ffffff and decompress fails later.
We could hit this problem with crashkernel booting that uses kexec loading
kernel above 4GiB.
We have decompress_* support:
1. inbuf[]/outbuf[] for kernel preboot.
2. inbuf[]/flush() for initramfs
3. fill()/flush() for initrd.
This bug only affect kernel preboot path that use outbuf[].
Add __decompress and take real out_buf_len for gunzip instead of guessing
wrong buf size.
Fixes: 1431574a1c4 (lib/decompressors: fix "no limit" output buffer length)
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Jon Medhurst <tixy@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://codeaurora.org/quic/kernel/agross-msm into next/late
Qualcomm ARM Based Device Tree Updates for v4.3-rc2
* Add labels for serial nodes to be used for aliasing and stdout-path
* Add stdout-path for APQ8064 Compulab QS600
* Add stdout-path for APQ8064 Inforce 6410
* Add stdout-path for APQ8074 Dragonboard
* Add stdout-path for APQ8084 Inforce 6540
* Add stdout-path for APQ8084 MTP
* Add stdout-path for IPQ8064 AP148
* Add stdout-path for MSM8660 Surf
* Add stdout-path for MSM8960 CDP
* Add stdout-path for MSM8974 Xperia Honami
* tag 'qcom-dt-for-4.3-rc2' of git://codeaurora.org/quic/kernel/agross-msm: (24 commits)
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
ARM: dts: qs600: Add real regulators to sdcc
ARM: dts: ifc6410: add real regulators for sdcc nodes.
ARM: dts: apq8064: remove temporary fixed regulator for mmc
ARM: dts: apq8064: fix missing gsbi cell-index
ARM: dts: apq8064: Add DT support for GSBI6 and for UART pin mux
ARM: dts: apq8064: add pm8921 mpp support
ARM: dts: apq8064: Add pm8921 mfd and its gpio node
ARM: dts: msm8974: Add smem reservation and node
ARM: dts: msm8974: Add tcsr mutex node
ARM: dts: qcom: Add ks8851 node for wired ethernet
...
|
|
* drivers/reset:
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
reset: reset-zynq: Adding support for Xilinx Zynq reset controller.
docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings.
MIPS: ath79: Add the reset controller to the AR9132 dtsi
reset: Add a driver for the reset controller on the AR71XX/AR9XXX
devicetree: Add bindings for the ATH79 reset controller
reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property
doc: dt: add documentation for lpc1850-rgu reset driver
reset: add driver for lpc18xx rgu
reset: sti: constify of_device_id array
ARM: STi: DT: Move reset controller constants into common location
MAINTAINERS: add include/dt-bindings/reset path to reset controller entry
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Cc: Tim Bird <tim.bird@sonymobile.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Cc: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Use stdout-path so that we don't have to put the console on the
kernel command line.
Cc: Mike Rapoport <mike.rapoport@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Add a label to the serial nodes that are being used for the
console.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Qualcomm ARM Based Device Tree Updates for v4.3
* Switch to use pinctrl compatible for GPIOs
* Add RPM regulators for MSM8960
* Add SPI Ethernet support on MSM8960 CDP
* Add SMEM support along with dependencies
* Add PM8921 support for GPIO and MPP
* Fix GSBI cell index
* Switch to use real regulators on APQ8064 w/ SDCC
|
|
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
