| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit e6a4eedd49ce27c16a80506c66a04707e0ee0116 ]
RTC interrupt level should be set to "LOW". This was revealed by the
introduction of commit:
f181987ef477 ("rtc: m41t80: use IRQ flags obtained from fwnode")
which changed the way IRQ type is obtained.
Fixes: 56c27310c1b4 ("ARM: dts: imx: Add Advantech BA-16 Qseven module")
Signed-off-by: Ian Ray <ian.ray@gehealthcare.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5654889a94b0de5ad6ceae3793e7f5e0b61b50b6 ]
On some flexcom nodes related to uart, the fifo sizes were wrong: fix
them to 32 data.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20251114103313.20220-2-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d5864dc5d5ea6a35983dd05295fb17f2f2f44ce upstream.
Unlike standalone spi peripherals, on sama5d2, the flexcom spi have fifo
size of 32 data. Fix flexcom/spi nodes where this property is wrong.
Fixes: 6b9a3584c7ed ("ARM: dts: at91: sama5d2: Add missing flexcom definitions")
Cc: stable@vger.kernel.org # 5.8+
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20251114140225.30372-1-nicolas.ferre@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
suspend
[ Upstream commit 2ff147fdfa99b8cbb8c2833e685fde7c42580ae6 ]
Commit 8c3170628a9c ("wifi: brcmfmac: keep power during suspend if board
requires it") changed default behavior of the BRCMFMAC driver, which now
keeps SDIO card powered during system suspend to enable optional support
for WOWL. This feature is not supported by the legacy Exynos4 based
boards and leads to WLAN disfunction after system suspend/resume cycle.
Fix this by annotating SDIO host used by WLAN chip with
'cap-power-off-card' property, which should have been there from the
beginning.
Fixes: f77cbb9a3e5d ("ARM: dts: exynos: Add bcm4334 device node to Trats2")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20251126102618.3103517-5-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
suspend
[ Upstream commit 97cc9c346b2c9cde075b9420fc172137d2427711 ]
Commit 8c3170628a9c ("wifi: brcmfmac: keep power during suspend if board
requires it") changed default behavior of the BRCMFMAC driver, which now
keeps SDIO card powered during system suspend to enable optional support
for WOWL. This feature is not supported by the legacy Exynos4 based
boards and leads to WLAN disfunction after system suspend/resume cycle.
Fix this by annotating SDIO host used by WLAN chip with
'cap-power-off-card' property, which should have been there from the
beginning.
Fixes: a19f6efc01df ("ARM: dts: exynos: Enable WLAN support for the Trats board")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20251126102618.3103517-4-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
suspend
[ Upstream commit 863d69923bdb6f414d0a3f504f1dfaeacbc00b09 ]
Commit 8c3170628a9c ("wifi: brcmfmac: keep power during suspend if board
requires it") changed default behavior of the BRCMFMAC driver, which now
keeps SDIO card powered during system suspend to enable optional support
for WOWL. This feature is not supported by the legacy Exynos4 based
boards and leads to WLAN disfunction after system suspend/resume cycle.
Fix this by annotating SDIO host used by WLAN chip with
'cap-power-off-card' property, which should have been there from the
beginning.
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20251126102618.3103517-3-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 97aee67e2406ea381408915e606c5f86448f3949 ]
Commit 8c3170628a9c ("wifi: brcmfmac: keep power during suspend if board
requires it") changed default behavior of the BRCMFMAC driver, which now
keeps SDIO card powered during system suspend to enable optional support
for WOWL. This feature is not supported by the legacy Exynos4 based
boards and leads to WLAN disfunction after system suspend/resume cycle.
Fix this by annotating SDIO host used by WLAN chip with
'cap-power-off-card' property, which should have been there from the
beginning.
Fixes: f1b0ffaa686f ("ARM: dts: exynos: Enable WLAN support for the UniversalC210 board")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://patch.msgid.link/20251126102618.3103517-2-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e40b061cd379f4897e705d17cf1b4572ad0f3963 ]
Move st,adc-freq, st,mod-12b, st,ref-sel, and st,sample-time properties
from the touchscreen subnode to the parent touch@44 node. These properties
are defined in the st,stmpe.yaml schema for the parent node, not the
touchscreen subnode, resolving the validation error about unevaluated
properties.
Fixes: 27538a18a4fcc ("ARM: dts: stm32: add STM32MP1-based Phytec SoM")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250915224611.169980-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3862123e9b56663c7a3e4a308e6e65bffe44f646 ]
The "ti,twl4030-power-n900" compatible string is obsolete and is not
supported by any in-kernel driver. Currently, the kernel falls back to
the second entry, "ti,twl4030-power-idle-osc-off", to bind a driver to
this node.
Make this fallback explicit by removing the obsolete board-specific
compatible. This preserves the existing functionality while making the
DTS compliant with the new, stricter 'ti,twl.yaml' binding.
Fixes: daebabd578647 ("mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250914192516.164629-4-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f7f3bc18300a230e0f1bfb17fc8889435c1e47f5 ]
The "ti,twl4030-power-beagleboard-xm" compatible string is obsolete and
is not supported by any in-kernel driver. Currently, the kernel falls
back to the second entry, "ti,twl4030-power-idle-osc-off", to bind a
driver to this node.
Make this fallback explicit by removing the obsolete board-specific
compatible. This preserves the existing functionality while making the
DTS compliant with the new, stricter 'ti,twl.yaml' binding.
Fixes: 9188883fd66e9 ("ARM: dts: Enable twl4030 off-idle configuration for selected omaps")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250914192516.164629-3-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d0c4b1723c419a18cb434903c7754954ecb51d35 ]
Fixes: 8e9d75fd2ec2 ("ARM: dts: am335x-netcom: add GPIO names for NetCom Plus 2-port devices")
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20251007103851.3765678-1-yegorslists@googlemail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ca7fffb6e92a7c93604ea2bae0e1c89b20750937 ]
The 'ethernet-ports' node in the SoC DTSI handles them already. Fixes:
arch/arm/boot/dts/renesas/r9a06g032-rzn1d400-db.dtb: switch@44050000 (renesas,r9a06g032-a5psw): Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
from schema $id: http://devicetree.org/schemas/net/dsa/renesas,rzn1-a5psw.yaml#
Fixes: 5b6d7c3c5861ad4a ("ARM: dts: r9a06g032-rzn1d400-db: Add switch description")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251007104624.19786-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 00df14f34615630f92f97c9d6790bd9d25c4242d ]
'bus-width' is defined for the corresponding vin input port already.
No need to declare it in the output port again. Fixes:
arch/arm/boot/dts/renesas/r8a7793-gose.dtb: composite-in@20 (adi,adv7180cp): ports:port@3:endpoint: Unevaluated properties are not allowed ('bus-width' was unexpected)
from schema $id: http://devicetree.org/schemas/media/i2c/adi,adv7180.yaml#
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20250929093616.17679-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 1b03346314b791ad966d3c6d59253328226a2b2d upstream.
The i.MX6UL reference manual lists two possible interrupt lines for
SAI3 (56 and 57, offset +32). The current device tree entry uses
the first one (24), which prevents IRQs from being handled properly.
Use the second interrupt line (25), which does allow interrupts
to work as expected.
Fixes: 36e2edf6ac07 ("ARM: dts: imx6ul: add sai support")
Signed-off-by: Maarten Zanders <maarten@zanders.be>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3d1c795bdef43363ed1ff71e3f476d86c22e059b ]
Luxul XAP-1440 has BCM54210E PHY at address 25.
Fixes: 44ad82078069 ("ARM: dts: BCM53573: Fix Ethernet info for Luxul devices")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20251002194852.13929-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f31e261712a0d107f09fb1d3dc8f094806149c83 ]
Rename the 'ssi2' and 'aud3' nodes to 'mux-ssi2' and 'mux-aud3' in the
audmux configuration of imx51-zii-rdu1.dts to comply with the naming
convention in imx-audmux.yaml.
This fixes the following dt-schema warning:
imx51-zii-rdu1.dtb: audmux@83fd0000 (fsl,imx51-audmux): 'aud3', 'ssi2'
do not match any of the regexes: '^mux-[0-9a-z]*$', '^pinctrl-[0-9]+$'
Fixes: ceef0396f367f ("ARM: dts: imx: add ZII RDU1 board")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 3f973d78d176768fa7456def97f0b9824235024f ]
Correct audio-codec interrupt should be PX3 while PX1 is used for external
microphone detection.
Tested-by: Winona Schroeer-Smith <wolfizen@wolfizen.net> # ASUS SL101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit cca41614d15ce2bbc2c661362d3eafe53c9990af ]
Add missing interrupt to magnetometer node.
Tested-by: Winona Schroeer-Smith <wolfizen@wolfizen.net> # ASUS SL101
Tested-by: Antoni Aloy Torrens <aaloytorrens@gmail.com> # ASUS TF101
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 27322753c8b913fba05250e7b5abb1da31e6ed23 ]
The dtbs_check validation for am335x-cm-t335.dtb flags an error
for an unevaluated 'num-serializer' property in the mcasp0 node.
This property is obsolete; it is not defined in the davinci-mcasp-audio
schema and is not used by the corresponding (or any) driver.
Remove this unused property to fix the schema validation warning.
Fixes: 48ab364478e77 ("ARM: dts: cm-t335: add audio support")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250830215957.285694-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
use correct boolean syntax in DTS
[ Upstream commit 5af5b85505bc859adb338fe5d6e4842e72cdf932 ]
The ti,keep-vref-on property, defined as a boolean flag in the Device
Tree schema, was incorrectly assigned a value (<1>) in the DTS file,
causing a validation error: "size (4) error for type flag". Remove
the value to match the schema and ensure compatibility with the driver
using device_property_read_bool(). This fixes the dtbs_check error.
Fixes: ed05637c30e6 ("ARM: dts: omap3-devkit8000: Add ADS7846 Touchscreen support")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/r/20250822225052.136919-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
use correct boolean syntax
[ Upstream commit 9658a92fad1889ff92fa4bd668cd61052687245a ]
The ti,en-ck32k-xtal property, defined as a boolean in the Device Tree
schema, was incorrectly assigned a value (<1>) in the DTS file, causing
a validation error: "size (4) error for type flag". The driver uses
of_property_read_bool(), expecting a boolean. Remove the value to fix
the dtbs_check error.
Fixes: 262178b6b8e5 ("ARM: dts: split am335x-baltos-ir5221 into dts and dtsi files")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Link: https://lore.kernel.org/all/20250822222530.113520-1-jihed.chaibi.dev@gmail.com/
Link: https://lore.kernel.org/r/20250822222530.113520-1-jihed.chaibi.dev@gmail.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 287066b295051729fb08c3cff12ae17c6fe66133 ]
According to the schematics, the CAN transceiver is connected to pins
GP7_3 and GP7_4, which correspond to CAN0 data group B.
Fixes: 0768fbad7fba1d27 ("ARM: shmobile: porter: add CAN0 DT support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/70ad9bc44d6cea92197c42eedcad6b3d0641d26a.1751032025.git.geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit ea9da67e2add7bd5f1e4b38dc2404480e711f4d8 upstream.
On SoCFPGA/Sodia board, mdio bus cannot be probed, so the PHY cannot be
found and the network device does not work.
```
stmmaceth ff702000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -19)
```
To probe the mdio bus, add "snps,dwmac-mdio" as compatible string of the
mdio bus. Also the PHY address connected to this board is 4. Therefore,
change to 4.
Cc: stable@vger.kernel.org # 6.3+
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 29341c6c18b8ad2a9a4a68a61be7e1272d842f21 ]
A previous commit changed the '#sound-dai-cells' property for the
kirkwood audio controller from 1 to 0 in the kirkwood.dtsi file,
but did not update the corresponding 'sound-dai' property in the
kirkwood-openrd-client.dts file.
This created a mismatch, causing a dtbs_check validation error where
the dts provides one cell (<&audio0 0>) while the .dtsi expects zero.
Remove the extraneous cell from the 'sound-dai' property to fix the
schema validation warning and align with the updated binding.
Fixes: e662e70fa419 ("arm: dts: kirkwood: fix error in #sound-dai-cells size")
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 47ef5256124fb939d8157b13ca048c902435cf23 ]
The polarity of the DE signal of the transceiver is active-high for
sending. Therefore rs485-rts-active-low is wrong and needs to be
removed to make RS485 transmissions work.
Signed-off-by: Annette Kobou <annette.kobou@kontron.de>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: 1ea4b76cdfde ("ARM: dts: imx6ul-kontron-n6310: Add Kontron i.MX6UL N6310 SoM and boards")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit a3a4be32b69c99fc20a66e0de83b91f8c882bf4c ]
This commit fixes a typo introduced in commit
ee368a10d0df ("ARM: dts: am335x-boneblack.dts: unique gpio-line-names").
gpio0_7 is located on the P9 header on the BBB.
This was verified with a BeagleBone Black by toggling the pin and
checking with a multimeter that it corresponds to pin 42 on the P9
header.
Signed-off-by: Albin Törnqvist <albin.tornqvist@codiax.se>
Link: https://lore.kernel.org/r/20250624114839.1465115-2-albin.tornqvist@codiax.se
Fixes: ee368a10d0df ("ARM: dts: am335x-boneblack.dts: unique gpio-line-names")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3440dcf8b994197c968fbafe047ce27eed226e8 ]
Address and size-cells are 1 and the ftm timer node takes two address
spaces in "reg" property, so this should be in two <> tuples. Change
has no functional impact, but original code is confusing/less readable.
Fixes: 07513e1330a9 ("ARM: dts: vf610: Add Freescale FlexTimer Module timer node.")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 929d8490f8790164f5f63671c1c58d6c50411cb2 upstream.
Commit b9bf5612610aa7e3 ("ARM: dts: am335x-bone-common: Increase MDIO
reset deassert time") already increased the MDIO reset deassert delay
from 6.5 to 13 ms, but this may still cause Ethernet PHY probe failures:
SMSC LAN8710/LAN8720 4a101000.mdio:00: probe with driver SMSC LAN8710/LAN8720 failed with error -5
On BeagleBone Black Rev. C3, ETH_RESETn is controlled by an open-drain
AND gate. It is pulled high by a 10K resistor, and has a 4.7µF
capacitor to ground, giving an RC time constant of 47ms. As it takes
0.7RC to charge the capacitor above the threshold voltage of a CMOS
input (VDD/2), the delay should be at least 33ms. Considering the
typical tolerance of 20% on capacitors, 40ms would be safer. Add an
additional safety margin and settle for 50ms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/9002a58daa1b2983f39815b748ee9d2f8dcc4829.1730366936.git.geert+renesas@glider.be
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9bf5612610aa7e38d58fee16f489814db251c01 upstream.
Prior to commit df16c1c51d81 ("net: phy: mdio_device: Reset device only
when necessary") MDIO reset deasserts were performed twice during boot.
Now that the second deassert is no longer performed, device probe
failures happen due to the change in timing with the following error
message:
SMSC LAN8710/LAN8720: probe of 4a101000.mdio:00 failed with error -5
Restore the original effective timing, which resolves the probe
failures.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20240531183817.2698445-1-colin.foster@in-advantage.com
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 325c6a441ae1f8fcb1db9bb945b8bdbd3142141e ]
Follow up the expected way of describing the SFPB hwspinlock and merge
hwspinlock node into corresponding syscon node, fixing several dt-schema
warnings.
Fixes: 24a9baf933dc ("ARM: dts: qcom: apq8064: Add hwmutex and SMEM nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-fix-nexus-4-v2-7-bcedd1406790@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4b0eb149df58b6750cd8113e5ee5b3ac7cc51743 ]
In order to fix DT schema warning and describe hardware properly, add
missing sleep clock to the timer node.
Fixes: f335b8af4fd5 ("ARM: dts: qcom: Add initial APQ8064 SoC and IFC6410 board device trees")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250318-fix-nexus-4-v2-6-bcedd1406790@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c72ede1c24be689733bcd2233a3a56f2478429c8 ]
NAND did not work on my USB-A9263. I discovered that the offending
commit converted the PIO bank for chip selects wrongly, so all A9263
boards need to be fixed.
Fixes: 1004a2977bdc ("ARM: dts: at91: Switch to the new NAND bindings")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20250402210446.5972-2-wsa+renesas@sang-engineering.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 67ba341e57ab158423818ed33bfa1c40eb0e5e7e ]
Dataflash did not work on my board. After checking schematics and using
the proper GPIO, it works now. Also, make it active low to avoid:
flash@0 enforce active low on GPIO handle
Fixes: 2432d201468d ("ARM: at91: dt: usb-a9263: add dataflash support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250404112742.67416-2-wsa+renesas@sang-engineering.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2b3db788f2f614b875b257cdb079adadedc060f3 ]
PLLD is usually used as parent clock for internal video devices, like
DSI for example, while PLLD2 is used as parent for HDMI.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Link: https://lore.kernel.org/r/20250226105615.61087-3-clamor95@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6e1a7bc8382b0d4208258f7d2a4474fae788dd90 ]
Commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific
PHY fixup") removed a PHY fixup that setted the clock mode and the LED
mode.
Make the Ethernet interface work again by doing as advised in the
commit's log, set clock mode and the LED mode in the device tree.
Fixes: c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 83964a29379cb08929a39172780a4c2992bc7c93 upstream.
The current solution for powering off the Apalis iMX6 is not functioning
as intended. To resolve this, it is necessary to power off the
vgen2_reg, which will also set the POWER_ENABLE_MOCI signal to a low
state. This ensures the carrier board is properly informed to initiate
its power-off sequence.
The new solution uses the regulator-poweroff driver, which will power
off the regulator during a system shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 4eb56e26f92e ("ARM: dts: imx6q-apalis: Command pmic to standby for poweroff")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c24f272ae751a9f54f8816430e7f2d56031892cc ]
During upstream process of Raspberry Pi 4 back in 2019 the ARMv7 stubs
didn't configured the ARM architectural timer. This firmware issue has
been fixed in 2020, which gave users enough time to update their system.
So drop this property to allow the use of the vDSO version of
clock_gettime.
Link: https://github.com/raspberrypi/tools/pull/113
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250222094113.48198-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0de09025f161f67c07978c4742e221243d070d41 ]
The ARM PL011 UART instances in BCM2711 are r1p5 spec, which means they
have 32-entry FIFOs. The correct periphid value for this is 0x00341011.
Thanks to N Buchwitz for pointing this out.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250223125614.3592-2-wahrenst@gmx.net
Fixes: 7dbe8c62ceeb ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 0cfbd7805fe13406500e6a6f2aa08f198d5db4bd upstream.
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f01 ("ARM: dts: gta04: fix excess dma channel usage")
CC: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1472ec1dc4419d0bae663c1a1e6cb98dc7881ad upstream.
A bus_dma_limit was added for l3 bus by commit cfb5d65f2595
("ARM: dts: dra7: Add bus_dma_limit for L3 bus") to fix an issue
observed only with SATA on DRA7-EVM with 4GB RAM and CONFIG_ARM_LPAE
enabled.
Since kernel 5.13, the SATA issue can be reproduced again following
the SATA node move from L3 bus to L4_cfg in commit 8af15365a368
("ARM: dts: Configure interconnect target module for dra7 sata").
Fix it by adding an empty dma-ranges property to l4_cfg and
segment@100000 nodes (parent device tree node of SATA controller) to
inherit the 2GB dma ranges limit from l3 bus node.
Note: A similar fix was applied for PCIe controller by commit
90d4d3f4ea45 ("ARM: dts: dra7: Fix bus_dma_limit for PCIe").
Fixes: 8af15365a368 ("ARM: dts: Configure interconnect target module for dra7 sata").
Link: https://lore.kernel.org/linux-omap/c583e1bb-f56b-4489-8012-ce742e85f233@smile.fr/
Cc: stable@vger.kernel.org # 5.13
Signed-off-by: Romain Naour <romain.naour@skf.com>
Link: https://lore.kernel.org/r/20241115102537.1330300-1-romain.naour@smile.fr
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 90234cf9b37c57201a24b78c217a91a8af774109 ]
Fix following validation error:
arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dtb: cir@10013000: $nodename:0: 'cir@10013000' does not match '^ir(-receiver)?(@[a-f0-9]+)?$'
from schema $id: http://devicetree.org/schemas/media/mediatek,mt7622-cir.yaml#
Fixes: 91044f38dae7 ("arm: dts: mt7623: add ir nodes to the mt7623.dtsi file")
Cc: linux-media@vger.kernel.org
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20240617094634.23173-1-zajec5@gmail.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4d9e5965df04c0adf260c3009c55d5fe240f7286 ]
Add no-1-8-v property to sdmmc0 node to keep VDDSDMMC power rail at 3.3V.
This property will stop the LDO regulator from switching to 1.8V when the
MMC core detects an UHS SD Card. VDDSDMMC power rail is used by all the
SDMMC interface pins in GPIO mode (PA0 - PA13).
On this board, PA10 is used as GPIO to enable the power switch controlling
USB Vbus for the USB Host. The change is needed to fix the PA10 voltage
level to 3.3V instead of 1.8V.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Suggested-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Tested-by: Andrei Simion <andrei.simion@microchip.com>
Link: https://lore.kernel.org/r/20241119160107.598411-3-cristian.birsan@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
sdmmc0 node
[ Upstream commit 2a7f1848d9d65a4deb366726ff8f33c9c64ac43b ]
On board the sdmmc0 interface is wired to a SD Card socket.
According with mmc-controller bindings, the mmc-ddr-3_3v property
is used for eMMC devices to enable high-speed DDR mode (3.3V I/O).
Remove the mmc-ddr-3_3v property from sdmmc0 node.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Link: https://lore.kernel.org/r/20231204072537.2991-1-mihai.sain@microchip.com
Signed-off-by: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Stable-dep-of: 4d9e5965df04 ("ARM: dts: microchip: sama5d27_wlsom1_ek: Add no-1-8-v property to sdmmc0 node")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 479b8227ffc433929ba49200182b6383569f9615 ]
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
DHCOM SoM
[ Upstream commit 73317d327123472cb70e9ecbe050310f1d235e93 ]
Deduplicate /aliases { serialN = ... } and /chosen node into
stm32mp15xx-dhcom-som.dtsi , since the content is identical
on all carrier boards using the STM32MP15xx DHCOM SoM. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Stable-dep-of: 479b8227ffc4 ("ARM: dts: stm32: Swap USART3 and UART8 alias on STM32MP15xx DHCOM SoM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 62a40a0d5634834790f7166ab592be247390d857 ]
The ahb reset is deasserted in probe before first register access, while the
stmmacheth-ocp reset needs to be asserted every time before changing the phy
mode in Arria10[1].
Changed in Upstream to "ahb"(331085a423b arm64: dts: socfpga: change the
reset-name of "stmmaceth-ocp" to "ahb" ).This change was intended for arm64
socfpga and it is not applicable to Arria10.
Further with STMMAC-SELFTEST Driver enabled, ethtool test also FAILS.
$ ethtool -t eth0
[ 322.946709] socfpga-dwmac ff800000.ethernet eth0: entered promiscuous mode
[ 323.374558] socfpga-dwmac ff800000.ethernet eth0: left promiscuous mode
The test result is FAIL
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -110
3. MMC Counters -110
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC -110
7. MC Filter -110
8. UC Filter 0
9. Flow Control -110
10. RSS -95
11. VLAN Filtering -95
12. VLAN Filtering (perf) -95
13. Double VLAN Filter -95
14. Double VLAN Filter (perf) -95
15. Flexible RX Parser -95
16. SA Insertion (desc) -95
17. SA Replacement (desc) -95
18. SA Insertion (reg) -95
19. SA Replacement (reg) -95
20. VLAN TX Insertion -95
21. SVLAN TX Insertion -95
22. L3 DA Filtering -95
23. L3 SA Filtering -95
24. L4 DA TCP Filtering -95
25. L4 SA TCP Filtering -95
26. L4 DA UDP Filtering -95
27. L4 SA UDP Filtering -95
28. ARP Offload -95
29. Jumbo Frame -110
30. Multichannel Jumbo -95
31. Split Header -95
32. TBS (ETF Scheduler) -95
[ 324.881327] socfpga-dwmac ff800000.ethernet eth0: Link is Down
[ 327.995360] socfpga-dwmac ff800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Link:[1] https://www.intel.com/content/www/us/en/docs/programmable/683711/21-2/functional-description-of-the-emac.html
Fixes: 331085a423b ("arm64: dts: socfpga: change the reset-name of "stmmaceth-ocp" to "ahb")
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b1a1ecb669bfa763ee5e86a038d7c9363eee7548 ]
Fix the compatible string for max31790 to match the binding document.
Fixes: 2b8d94f4b4a4 ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Signed-off-by: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Link: https://patch.msgid.link/20241003074251.3818101-6-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c64ac96f8f8d957cdc6ec3c93dd9a6c4e6d78506 ]
Add the required properties for IO expander on fan boards.
Fixes: 2b8d94f4b4a4 ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Signed-off-by: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Link: https://patch.msgid.link/20241003074251.3818101-5-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit ece3e20e3389ec8a32944ad44746ee379bf1d3eb ]
Remove the space in the compatible string of adm1272 to match the
pattern of compatible.
Fixes: 2b8d94f4b4a4 ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Signed-off-by: Ricky CX Wu <ricky.cx.wu.wiwynn@gmail.com>
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Fixes: 2b8d94f4b4a4765d ("ARM: dts: aspeed: yosemite4: add Facebook Yosemite 4 BMC")
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://patch.msgid.link/20240927085213.331127-1-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4ea654242e0c75bdf6b45d3c619c5fdcb2e9312a ]
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e34 ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
