| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add definitions for PCIe legacy INTx interrupts.
This is required for example in a scenario where a driver requests only
one of the legacy interrupts (INTA). Without this, the driver would be
notified on events on all 4 (INTA, INTB, INTC, INTD), even if it
requested only one of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Add definitions for PCIe legacy INTx interrupts.
This is required for example in a scenario where a driver requests only
one of the legacy interrupts (INTA). Without this, the driver would be
notified on events on all 4 (INTA, INTB, INTC, INTD), even if it
requested only one of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Both the Linkstation LS-CHLv2 and the LS-XHL have only one ethernet
port. This has always been wrong, i.e. the board code used to set up
both ports, but the driver will play nice and return -ENODEV if the
assiciated PHY is not found. Nevertheless, it is wrong. Remove it.
Fixes: 876e23333511 ("ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Commit 327e15428977 ("ARM: dts: kirkwood: consolidate common pinctrl
settings") unknowingly broke the serial output on this board. Before
this commit, the pinmux was still configured by the bootloader and the
kernel didn't reconfigured it again. This was an oversight by the
initial board support where the pinmux for the serial line was never
configured by the kernel. But with this commit, the serial line will be
reconfigured to the wrong pins. This is especially confusing, because
the output still works, but the input doesn't. Presumingly, the input is
reconfigured to MPP10, but the output is connected to both MPP11 and
MPP5.
Override the pinmux in the board device tree.
Fixes: 327e15428977 ("ARM: dts: kirkwood: consolidate common pinctrl settings")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
There is a bug in Turris Omnia's schematics, whereupon the MPP[26] pin,
which is routed to CN11 pin header, is documented as SPI CS1, but
MPP[26] pin does not support this function. Instead it controls chip
select 2 if in "spi0" mode.
Fix the name of the pin node in pinctrl node and fix the comment in SPI
node.
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/dt
AT91 DT for v6.1
It contains:
- one new LAN966X based board, namely lan966x-pcb8290
- gpio leds support for lan966x-pcb8291 and lan966x-pcb8309
- a cleanup for sam9x60ek to avoid DT compilation warning due to regulators
* tag 'at91-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: lan966x: add led configuration
ARM: dts: at91: sam9x60ek: remove simple-bus for regulators
ARM: dts: lan966x: add support for pcb8290
Link: https://lore.kernel.org/r/20220902085845.4193579-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes for 6.0
It contains:
- fixes for self-refresh on SAMA7G5 while in AT91 power management modes:
one disabling a DDR PHY controller DLL which has been proved to be buggy
and can introduce glitches that can cause unexpected behavior; one
fixing the DDR PHY recalibration which cannot work for all possible
cases (due to hardware bug) while using backup and self-refresh AT91
power management mode;
- one defconfig fix to remove CONFIG_MICROCHIP_PIT64B from all AT91
defconfigs;
- multiple device tree fixes for regulators to avoid having some of them
enabled all the time and to describe min and max output ranges
according to board capabilities.
* tag 'at91-fixes-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2_icp: don't keep vdd_other enabled all the time
ARM: dts: at91: sama5d27_wlsom1: don't keep ldo2 enabled all the time
ARM: dts: at91: sama7g5ek: specify proper regulator output ranges
ARM: dts: at91: sama5d2_icp: specify proper regulator output ranges
ARM: dts: at91: sama5d27_wlsom1: specify proper regulator output ranges
ARM: at91: pm: fix DDR recalibration when resuming from backup and self-refresh
ARM: at91: pm: fix self-refresh for sama7g5
ARM: configs: at91: remove CONFIG_MICROCHIP_PIT64B
Link: https://lore.kernel.org/r/20220902085744.4193554-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
6.0, please pull the following:
- William fixes a number of the recently submitted DTS files for 63178,
6846, 6878 to have correct PSCI node propertie as well as correct timer
CPU masks
* tag 'arm-soc/for-6.0/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcmbca: bcm6878: cosmetic change
ARM: dts: bcmbca: bcm6878: fix timer node cpu mask flag
ARM: dts: bcmbca: bcm6846: fix interrupt controller node
ARM: dts: bcmbca: bcm6846: clean up psci node
ARM: dts: bcmbca: bcm6846: fix timer node cpu mask flag
ARM: dts: bcmbca: bcm63178: cosmetic change
ARM: dts: bcmbca: bcm63178: fix interrupt controller node
ARM: dts: bcmbca: bcm63178: clean up psci node
ARM: dts: bcmbca: bcm63178: fix timer node cpu mask flag
Link: https://lore.kernel.org/r/20220829225103.753223-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add led configuration for pcb8291 and pcb8309. Both pcbs have 4 leds which
are connected to the sgpio controller.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220902062447.443846-1-horatiu.vultur@microchip.com
|
|
VDD_OTHER is not connected to any on board consumer thus it is not
needed to keep it enabled all the time.
Fixes: 68a95ef72cef ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-9-claudiu.beznea@microchip.com
|
|
ldo2 is not used by any consumer on sama5d27_wlsom1 board, thus
don't keep it enabled all the time.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-8-claudiu.beznea@microchip.com
|
|
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-7-claudiu.beznea@microchip.com
|
|
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 68a95ef72cef ("ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-6-claudiu.beznea@microchip.com
|
|
Min and max output ranges of regulators need to satisfy board
requirements not PMIC requirements. Thus adjust device tree to
cope with this.
Fixes: 5d4c3cfb63fe ("ARM: dts: at91: sama5d27_wlsom1: add SAMA5D27 wlsom1 and wlsom1-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-5-claudiu.beznea@microchip.com
|
|
Bindings expect Power-on node name to be "pon":
'power-on@800' do not match any of the regexes
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220828084341.112146-4-krzysztof.kozlowski@linaro.org
|
|
Bindings expect LPG/PWM node name to be "pwm":
pmic@5: 'lpg' does not match any of the regexes
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220828084341.112146-3-krzysztof.kozlowski@linaro.org
|
|
Bindings expect VADC node name to be "adc":
pmic@0: 'vadc@3100' does not match any of the regexes
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220828084341.112146-2-krzysztof.kozlowski@linaro.org
|
|
Use respective GPIO_ACTIVE_LOW/HIGH flags for tlmm GPIOs. Include
gpio.h header if this is first usage of that flag.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220802153947.44457-5-krzysztof.kozlowski@linaro.org
|
|
Fixed regulators, like stub for SDCC Power, are not part of SoC, so they
should be outside of the soc node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220810080516.166866-4-krzysztof.kozlowski@linaro.org
|
|
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
The pre/post DTBS are the same.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220810080516.166866-3-krzysztof.kozlowski@linaro.org
|
|
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
The pre/post DTBS are the same.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220810080516.166866-2-krzysztof.kozlowski@linaro.org
|
|
Using node paths to extend or override a device tree node is error
prone. If there was a typo error, a new node will be created instead of
extending the existing node. This will lead to run-time errors that
could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time). This also reduces the indentation making the code
easier to read.
The pre/post DTBS are the same.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220810080516.166866-1-krzysztof.kozlowski@linaro.org
|
|
ipq8065 SoC is based on ipq8064-v2.0 with a more clocked CPU and
an increased voltage output with the smb208 regulators.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718161826.4943-3-ansuelsmth@gmail.com
|
|
ipq8062 SoC is based on ipq8064-v2.0 with lower supported freq, lack of
usb port and a reduced voltage output with the smb208 regulators.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718161826.4943-2-ansuelsmth@gmail.com
|
|
Add ipq8064-v2.0 dtsi variant that differ from original ipq8064 SoC for
some additional pcie, sata and usb configuration values, additional
reserved memory and serial output.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718161826.4943-1-ansuelsmth@gmail.com
|
|
Replace deprecated perst-gpio properties with up-to-date perst-gpios
in the arm32 Qualcomm Snapdragon device trees.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220506152107.1527552-8-dmitry.baryshkov@linaro.org
|
|
Qualcomm PCIe devices are not really compatible with the snps,dw-pcie.
Unlike the generic IP core, they have special requirements regarding
enabling clocks, toggling resets, using the PHY, etc.
This is not to mention that platform snps-dw-pcie driver expects to find
two IRQs declared, while Qualcomm platforms use just one.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220506152107.1527552-7-dmitry.baryshkov@linaro.org
|
|
After adding all necessary support for MSM8916 SMP/cpuidle without PSCI
on ARM32, build the Samsung Galaxy E5/E7/Grand Max device trees from the
arm64 tree together with the ARM32 include to allow booting this device on
ARM32.
The approach to include device tree files from other architectures is
inspired from e.g. the Raspberry Pi (bcm2711-rpi-4-b.dts) where this is
used to build the device tree for both ARM32 and ARM64.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724095413.14135-1-linmengbo0689@protonmail.com
|
|
Keep regulators as individual devices. There is no need to have them
under simple bus. This will throw compilation warnings like:
- unnecessary #address-cells/#size-cells without "ranges" or child "reg"
property.
- node has a unit name, but no reg or ranges property.
While at it move it down a bit in the file to keep entries sorted
alphabetically.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220826083927.3107272-10-claudiu.beznea@microchip.com
|
|
Add basic support for pcb8290. It has 2 lan8814 phys(each phy is a
quad-port) on the external MDIO bus and no SFP ports.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220825065135.1075049-1-horatiu.vultur@microchip.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/fixes
These are some Versatile family DTS fixes, fixing some
node names and clock names related to SPI.
* tag 'versatile-dts-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: versatile: Update spi clock-names property
ARM: dts: realview: Update spi clock-names property
ARM: dts: integratorap: Update spi node properties
Link: https://lore.kernel.org/r/CACRpkdZfTe8NSGR2ZCkn-1JcNobjfWeXqajSqcJMp8+WtY+2Xw@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The NS2502 uses hardcoded partitions but parsing the RedBoot
FIS should work fine, given that this flash seems to be using
0x200000 erase blocks.
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/20220412220358.3674598-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I believed that gigabit was not working due to unknown missing GPIO.
But the problem was due to Marvell PHY incorrectly setting delay.
Now it is fixed, gigabit works.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I believed that gigabit was not working due to some unknown missing GPIO.
In fact, gigabit worked when REALTEK_PHY was compiled out.
So the problem was due to PHY delay and we need to use rgmii-id.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add hace node to device tree for AST2500/AST2600.
Signed-off-by: Neal Liu <neal_liu@aspeedtech.com>
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Reviewed-by: Dhananjay Phadke <dphadke@linux.microsoft.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The SoM itself provides the display interface, see [1] page 20.
Those pins have to be used as the RGB/DPI interface or not used
at all. So rather than duplicate the pinmux settings in every
carrier board DT, better move them into the SoM DTSI.
[1] https://wiki.dh-electronics.com/images/2/2e/DOC_DHCOM-Standard-Specification_R01_2016-11-17.pdf
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx6ull-kontron-bl.dtb wasn't build as part of the
CONFIG_SOC_IMX6UL option. Add it to the list.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is no need in differentiating between the different SoM versions
that only differ in memory size, etc. It's much cleaner to simplify
the devicetrees and let them be more generic.
If necessary the bootloader will update the devicetree dynamically
to contain the correct size of the memory.
We also get rid of the N6xxx notation in the compatibles and file
names, as they are not really used anymore and often result in
confusion.
This is a breaking change, but the impact shouldn't be too big and it
makes usage and maintenance easier in the future.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The node names should be generic and DT schema expects certain pattern.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add fixed power supplies to the EEPROM nodes to suppress a warning:
at24 2-0050: supply vcc not found, using dummy regulator
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
DT spec expects generic DMA controller node name as "dma-controller" to
enable validations.
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i2c2 is routed to the pins dedicated as DDC in the module standard.
Reduce clock rate to 100kHz to be in line with VESA standard and hook
this bus up to the HDMI node.
Fixes: 708ed2649ad8 ("ARM: dts: imx6qdl-kontron-samx6i: increase i2c-frequency")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[m.felsch@pengutronix.de: add fixes line]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ethernet-phy node so we can drop the deprecated fec phy-reset-gpios
property. The reset-assert-us value is taken from the existing logic
since the fec driver will add an 1ms assert delay per default if
phy-reset-gpios is used and phy-reset-duration is not specified.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Drop the "winbond,w25q16dw" compatible since it causes to set the
MODALIAS to w25q16dw which is not specified within spi-nor id table.
Fix this by use the common "jedec,spi-nor" compatible.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The regulator node 'regulator-3p3v-s0' was dupplicated. Remove it to
clean the DTS.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This naming error slipped through, so now that a new backlight node has
been added with correct spelling, fix this one also.
Fixes: 98efa526a0c4 ("ARM: dts: imx6qdl-vicut1/vicutgo: Add backlight_led node")
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
