summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts
AgeCommit message (Collapse)AuthorFilesLines
2018-03-27Merge tag 'socfpga_dts_for_v4.17' of ↵Arnd Bergmann1-1/+1
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt Pull "SoCFPGA DTS updates for v4.17" from Dinh Nguyen: - Fix GIC PPI warning - Stratix10 platform updates - Disable over-current for Arria10 devkit - Enable watchdog timer * tag 'socfpga_dts_for_v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm: dts: socfpga: fix GIC PPI warning arm64: dts: stratix10: disable false USB overcurrent on devkit arm64: dts: stratix10: enable watchdog timer on the S10 devkit
2018-03-27Merge tag 'omap-for-v4.17/dt-pt2-signed' of ↵Arnd Bergmann7-8/+137
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt Pull "Second set of dts changes for omap variants for v4.17" from Tony Lindgren: This series of patches configures few new drivers and adds omap5 specific nodes: - Enable USB OTG mode for xhci on am437x - A series of changes to configure aux control module instance on omap5 mostly to get the audio clocks configured - A series of changes to update droid4 for MDM6600 modem USB PHY and UART1 pinctrl * tag 'omap-for-v4.17/dt-pt2-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: omap4-droid4: Configure uart1 pins ARM: dts: omap4-droid4: Configure MDM6600 USB PHY ARM: dts: omap4-droid4: Fix USB PHY port naming ARM: dts: omap5-board-common: Add phandle for mclk clock for twl6040 ARM: dts: omap5: add fref_xtal_ck support ARM: dts: omap5: add support for control module wkup pad config dt-bindings: omap5: ctrl: Support for control module wkup pad config ARM: dts: am43xx: Enable dual-role mode for USB1
2018-03-27Merge tag 'sunxi-h3-h5-for-4.17' of ↵Arnd Bergmann93-226/+574
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard: Here is our usual bunch of changes to the common DTSI shared between arm and arm64, and their associated device trees. Even though the diffstat is quite big, it's been mostly just cleanups. The big feature is that the HDMI is now suported on H3 and H5 boards. * tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus ARM: dts: sun8i-h3: Add Mali node ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards ARM: dts: sun8i: h3: Enable HDMI output on H3 boards ARM: dts: sunxi: h3/h5: Add HDMI pipeline ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property ARM: dts: nanopi-neo-air: Add WiFi / eMMC
2018-03-27Merge tag 'sunxi-dt-for-4.17' of ↵Arnd Bergmann27-38/+1453
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt Pull "Allwinner DT changes for 4.17" from Maxime Ripard: There is a bunch of significant additions for this release cycle: - The A83t now has HDMI support - The A80 finally has SMP support (without PSCI, unfortunately) - The A80 has preliminary display support And also: - a number of boards based on old (A10, A20) SoCs now have the HDMI support enabled. - The display frontend is enabled on the A33, allowing to use it for hardware display scaling - New boards: Olimex A20-SOM204 variants * tag 'sunxi-dt-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (39 commits) ARM: dts: sun9i: cubieboard4: Enable VGA display output ARM: dts: sun9i: Add pinmux settings for LCD0 RGB888 output. ARM: dts: sun9i: Add device nodes for documented display pipelines for A80 ARM: dts: sun8i: reference tablet design: Enable PMIC power supplies ARM: dts: sun8i: a33: Enable A33 internal audio codec on A33-OLinuXino ARM: dts: sun8i: a33: Enable PMIC power supplies on A33-OLinuXino ARM: dts: sun8i: a33: Drop sunxi-common-regulators.dtsi for A33-OLinuXino ARM: dts: sun8i: a33: Drop GPIO pinmux settings for A33-OLinuXino ARM: dts: sun9i: Add enable-method for SMP support for the A80 SoC ARM: dts: sun8i: h3: Add eMMC for NanoPi M1 Plus ARM: dts: sun8i: a711: set regulator for each cluster of CPUs ARM: dts: sun8i: a83t: add stable OPP tables and CPUfreq ARM: dts: sun8i: a83t: add cpu0 and cpu100 labels ARM: dtsi: axp81x: remove IP name from DT node name ARM: dtsi: sun8i: a711: enable battery power supply subnode ARM: dtsi: axp81x: add battery power supply subnode ARM: dtsi: axp81x: add node for ADC ARM: dtsi: axp22x: add node for ADC ARM: dtsi: axp209: add node for ADC ARM: dts: sun7i: Enable HDMI support on the Orange Pi mini ...
2018-03-27Merge tag 'at91-ab-4.17-dt2' of ↵Arnd Bergmann13-87/+87
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt Pull "AT91 DT for 4.17 #2" from Alexandre Belloni: Pinctrl fixes, the UART pullups were discussed back in 2016. * tag 'at91-ab-4.17-dt2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: ARM: dts: at91sam9260: pullup rx on usart0 ARM: dts: at91rm9200: pullup rx on uart0 ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on tx ARM: dts: at91: at91sam9g25: fix mux-mask pinctrl property
2018-03-27Merge tag 'amlogic-dt-1' of ↵Arnd Bergmann3-4/+152
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt Pull "Amlogic 32-bit DT updates for v4.17" from Kevin Hilman: - odroid-c1: add microSD, ethernet, USB reset - add reset controller - fix requesting GPIOs greater than GPIOZ_3 * tag 'amlogic-dt-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: dts: meson8b: the CBUS GPIO controller only has 83 GPIOs ARM: dts: meson8b-odroidc1: add microSD support ARM: dts: meson8b: add the I2C clocks ARM: dts: meson8b-odroidc1: ethernet support ARM: dts: meson8b: extend ethernet controller description ARM: dts: meson8: add the USB reset line ARM: dts: meson8: add the reset controller ARM: dts: meson8b: grow the reset controller memory zone
2018-03-27Merge tag 'qcom-dts-for-4.17' of ↵Arnd Bergmann5-2/+92
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt Pull "Qualcomm Device Tree Changes for v4.17" from Andy Gross: * Add initial DTS file for Samsung Galaxy S5 * Fixups for castor touchscreen node * Fixup QS600 at23 manufacturer * Add XOADC and IIO to APQ8064 * tag 'qcom-dts-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/agross/linux: ARM: dts: msm8974: castor: Fix typo and add startup delay in touchscreen node ARM: dts: add XOADC and IIO HWMON to APQ8064 ARM: dts: use 'atmel' as at24 manufacturer for qcom-apq8064-cm-qs600 ARM: dts: qcom: Add initial DTS file for Samsung Galaxy S5 phone
2018-03-27ARM: dts: gemini: Remove "cooling-{min|max}-level" for gpio-fan nodeViresh Kumar1-2/+0
The "cooling-min-level" and "cooling-max-level" properties are not parsed by any part of the kernel currently and the max cooling state of gpio-fan cooling device is found by referring to the "gpio-fan,speed-map" instead. Remove the unused properties from the gpio-fan node. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2018-03-27Merge tag 'armsoc-versatile-drm-dts' of ↵Arnd Bergmann7-104/+296
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt Pull "DTS changes for RealView+Versatile" from Linus Walleij: This augments the RealView and Versatile device trees to properly define the VGA and panel connectors in preparation for DRM. * tag 'armsoc-versatile-drm-dts' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator: ARM: dts: Augment panel setting for Versatile ARM: dts: Add Versatile IB2 device tree ARM: dts: Augment VGA connector bridge on Realview PBX ARM: dts: Augment VGA connector bridge on Realview EB ARM: dts: Augment VGA connector bridge on PB1176 ARM: dts: Augment VGA connector bridge on PB11MPcore
2018-03-27Merge tag 'v4.16-next-dts32' of ↵Arnd Bergmann3-42/+223
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt Pull "ARM: mediatek: dts32 updates for v4.16-next" from Matthias Brugger: mt7623: - fix style issues of the dts - add cpu clock properties - add PCI controller - add mt7623 reference board banapi-r2: - enable missing uarts - fix regulator for mmc - fix USB initialization * tag 'v4.16-next-dts32' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: arm: dts: mt7623: add PCIe related nodes arm: dts: mt7623: use - instead of _ in DT node name arm: dts: mt7623: remove useless property pinctrl-names at node switch@0 arm: dts: mt7623: add related clock properties to cpu[1-3] nodes arm: dts: mt7623: enable three available UARTs on bananapi-r2 arm: dts: mt7623: fix the regulators mmc should use on bananapi-r2 arm: dts: mt7623: fix USB initialization fails on bananapi-r2 dt-bindings: arm: mediatek: add support for more mt7623 reference boards
2018-03-27Merge tag 'samsung-dt-4.17-2' of ↵Arnd Bergmann6-1/+69
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt Pull "Samsung DTS ARM changes for v4.17, part two" from Krzysztof Kozłowski: 1. Fix audio on Exynos5250 Chromebook Snow. 2. Enable HDMI audio Chromebook Snow, Peach Pit and Peach Pi. 3. Fix debounce of "OK" key on Midas (Trats2, Galaxy S3) boards. * tag 'samsung-dt-4.17-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: exynos: Add #sound-dai-cells property to exynos5250 i2s nodes ARM: dts: exynos: Fix "debounce-interval" property misspelling in Midas ARM: dts: exynos: Enable HDMI audio support on Peach Pi ARM: dts: exynos: Enable HDMI audio support on Peach Pit ARM: dts: exynos: Enable HDMI audio on Snow Chromebook ARM: dts: exynos: Add missing clock and DAI properties to the max98095 node in Snow Chromebook ARM: dts: exynos: Add audio clocks configuration for Snow Chromebook ARM: dts: exynos: Add #sound-dai-cells property to hdmi node in exynos5250.dtsi
2018-03-27Merge tag 'renesas-dt-for-v4.17' of ↵Arnd Bergmann19-6972/+8071
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman: * Silk board with R-Car E2 (r8a7794) SoC - Add r1ex24002 EEPROM to DT Magnus Damm says "Extend the Silk board support to include U14 which is an I2C based EEPROM hooked up to the I2C1 bus." - Add GPIO keys to DT Magnus Damm says "Extend the Silk board support to include SW3, SW4, SW6 and SW12. They are all connected via GPIO lines and handled by the gpio-keys driver" * Marzen board with R-Car H1 (r7a7779) SoC - Add SDHI0 VCCQ Regulator Magnus Damm says "Add support for the on-board voltage regulator hooked up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1 tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V. OUT goes to the pull-ups for the data pins of SDHI0." * Porter board with R-Car M3W (r8a7791) SoC - Fix HDMI output routing Laurent Pinchart says "The HDMI encoder is connected to the RGB output of the DU, which is port@0, not port@1." * iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven) - Enable cmt0 * Stout board with R-Car H2 (r8a7790) SoC - Initial support * Lager board with R-Car H2 (r8a7790) SoC - Add CEC clock for HDMI transmitter Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz fixed clock for the CEC block. Specify this in the dts to enable CEC support." - Move cec_clock to root node By definition nodes without a bus address do not belong on the bus * kzm9d board with EMMA Mobile EV2 (EMEV2) SoC - Fix "debounce-interval" property misspelling * RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs - Add IPMMU DT nodes - Add VSP support * R-Car Gen2 boards - Use I2C demuxer for This allows run-time switching between alternate I2C IP blocks * R-Car Gen2 and RZ/G1 SoCs - Clean up DT files to ease future maintenance + add soc node for IP attached to the bus + sort subnodes of soc and root node + consistently use single space after = * R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs - Reduce size of thermal registers According to the "User's Manual: Hardware" v2.00 the registers at base 0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the case on the r8a73a4 (R-Mobile APE6). This should not have any runtime affect as mapping granularity is PAGE_SIZE. * tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits) ARM: dts: silk: Add GPIO keys to DT ARM: dts: silk: Add r1ex24002 EEPROM to DT ARM: dts: marzen: Add SDHI0 VCCQ Regulator ARM: dts: stout: Initial r8a7790 Stout board support ARM: dts: lager: Move cec_clock to root node ARM: dts: kzm9d: Fix "debounce-interval" property misspelling ARM: dts: gose: use demuxer for I2C4 ARM: dts: gose: use demuxer for I2C2 ARM: dts: silk: use demuxer for I2C1 ARM: dts: alt: use demuxer for I2C1 ARM: dts: porter: use demuxer for I2C2 ARM: dts: koelsch: use demuxer for I2C4 ARM: dts: koelsch: use demuxer for I2C2 ARM: dts: lager: use demuxer for IIC3/I2C3 ARM: dts: lager: use demuxer for IIC2/I2C2 ARM: dts: r8a7745: Add VSP support ARM: dts: r8a7743: Add VSP support ARM: dts: r8a7745: Add IPMMU DT nodes ARM: dts: r8a7743: Add IPMMU DT nodes ARM: dts: r8a7745: sort subnodes of soc node ...
2018-03-27Merge tag 'tegra-for-4.17-arm-dt' of ↵Arnd Bergmann16-93/+2425
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt Pull "ARM: tegra: Device tree changes for v4.17-rc1" from Thierry Reding: Support for the VDE is added on Tegra30 along with some general cleanup and some improvements to the various Toradex boards. * tag 'tegra-for-4.17-arm-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux: ARM: tegra: apalis-tk1: Support v1.2 hardware revision ARM: tegra: apalis-tk1: Copyright period, spurious newlines ARM: tegra: apalis-tk1: Hog group for ethernet, PCIe, reset GPIOs ARM: tegra: apalis-tk1: Add missing as3722 gpio0 configuration ARM: tegra: apalis-tk1: Activate PWM pin muxing for pwm3 ARM: tegra: apalis-tk1: Set critical trips ARM: tegra: apalis/colibri: Remove unneeded reg property ARM: tegra: apalis/colibri: Use correct compatible for RTC ARM: tegra: Fix I2C bus frequencies on Apalis/Colibri ARM: tegra: venice2: Remove duplicate pcie-1 node ARM: tegra: beaver: Remove invalid uses of rsvd1 ARM: tegra: Use proper IRQ type definitions ARM: tegra: Fix ULPI regression on Tegra20 ARM: tegra: Add unit address to VDE IRAM area ARM: tegra: Add video decoder node on Tegra30 ARM: tegra: Add IRAM node on Tegra30
2018-03-23arm: dts: socfpga: fix GIC PPI warningPhilipp Puschmann1-1/+1
Fixes the warning "GIC: PPI13 is secure or misconfigured" by changing the interrupt type from level_low to edge_raising Signed-off-by: Philipp Puschmann <pp@emlix.com> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2018-03-21ARM: dts: at91sam9260: pullup rx on usart0Peter Rosin1-2/+2
For consistency with all other serial pins, add this pullup. It also prevents the signal from floating and so consuming a useless extra amount of power in crowbarred state if nothing is connected to RX. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-21ARM: dts: at91rm9200: pullup rx on uart0Peter Rosin1-2/+2
For consistency with all other serial pins, add this pullup. It also prevents the signal from floating and so consuming a useless extra amount of power in crowbarred state if nothing is connected to RX. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-21ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on txPeter Rosin12-82/+82
Remove pullup on uart TX signals, they are push-pull outputs thus pullups are pointless. Add pullup on uart RX signals, they prevent the RX signals to be left floating and so consuming a useless extra amount of power in crowbarred state if nothing is connected to RX. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-21ARM: dts: at91: at91sam9g25: fix mux-mask pinctrl propertyNicolas Ferre1-1/+1
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them have a 'C' function. So the pinctrl property mask ends up being the same as the other SoC of the at91sam9x5 series. Reported-by: Marek Sieranski <marek.sieranski@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-21ARM: dts: meson8b: the CBUS GPIO controller only has 83 GPIOsMartin Blumenstingl1-1/+1
Update the "gpio-ranges" property of the CBUS GPIO controller on Meson8b because it only provides 83 GPIOs. The GPIO definitions in include/dt-bindings/gpio/meson8b-gpio.h inherited all GPIOs from Meson8 until recently. However, Meson8b does not support all GPIOs which are supported by Meson8 (Meson8b doesn't have a GPIOZ bank, most of the pins from the GPIODV bank are missing on Meson8b - just to name a few differences). The actual number of GPIOs is only 83, instead of 120 from Meson8 plus the 10 GPIOs from the DIF bank on Meson8b. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-21ARM: dts: meson8b-odroidc1: add microSD supportLinus Lüssing2-0/+66
The Odroid C1 features a microSD slot. This patch adds the necessary DT bindings to support it. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-20ARM: dts: omap4-droid4: Configure uart1 pinsTony Lindgren1-0/+33
These are needed to use the n_gsm driver for TS 27.010 UART multiplexing. Note that support for the OOB wake gpio is still missing so the UART is not yet usable for n_gsm. Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: omap4-droid4: Configure MDM6600 USB PHYTony Lindgren1-0/+64
Configure MDM6600 USB PHY. Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: omap4-droid4: Fix USB PHY port namingTony Lindgren1-3/+3
We have a USB OCHI PHY on port 1 for mdm6600. Port 2 is using transceiverless logic (TLL) for USB EHCI for w3glte modem. Let's also fix the node name to use usb-phy while at it. Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sebastian Reichel <sre@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: omap5-board-common: Add phandle for mclk clock for twl6040Peter Ujfalusi1-2/+2
The xref_xtal clock is used by twl6040 as mclk. It is needed for the HPPLL internally. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: omap5: add fref_xtal_ck supportTero Kristo1-0/+10
The clock is directly sourced from sys_clkin, and provides an external output clock for (typically) TWL6040 chip. Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: omap5: add support for control module wkup pad configTero Kristo1-0/+22
The pad configuration area under control module wkup has some miscellaneous config registers, that are not pinmux related. Add a separate area for these, and add support for syscon / clocks under this new area. Signed-off-by: Tero Kristo <t-kristo@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: am43xx: Enable dual-role mode for USB1Roger Quadros3-3/+3
USB1 port is micro-AB type and can function as peripheral as well as host. Enable dual-role mode for USB1. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2018-03-20ARM: dts: Augment panel setting for VersatileLinus Walleij1-2/+81
This adds the actual VGA DAC bridge that is used in the Versatile AB, and sets the mode to 640x480 VGA. The "clcd" clock was incorrectly named, the proper name (from bindings) is "clcdclk". So far drivers survived by just getting the first clock, but future drivers will use named clocks. We add the panel connector to the "arm,versatile-tft-panel" as well, the signals actually fork on the board, reaching both the VGA DAC and the display connector. Cc: Mali DP Maintainers <malidp@foss.arm.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20ARM: dts: Add Versatile IB2 device treeLinus Walleij2-0/+27
The Versatile board can be equipped with a interface board just named "IB2". This was created in the early 2000s for prototyping GSM candybar phone form factor products. The IB2 board contains: - Cascaded interrupt controller - Enfora Enabler GSM0308 quad-band module with antenna and separate audio jack - Keypad with joystick - Sanyo 2.5" color display - A 28-pin connector for mounting a camera This adds a DTS file for the combination of the Versatile AB with an IB2 daughterboard mounted, making the LED blink and making the system controller available for drivers, such as the panel driver. The device tree bindings already exist in Documentation/devicetree/bindings/arm/arm-boards. Cc: Mali DP Maintainers <malidp@foss.arm.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20ARM: dts: Augment VGA connector bridge on Realview PBXLinus Walleij1-27/+55
The PL111 in the ARM reference platforms are connected to "panels" that are actually dumb VGA DAC connector bridges. Now that we can support the proper bridges in the DRM driver, fix this up. Cc: Mali DP Maintainers <malidp@foss.arm.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20ARM: dts: Augment VGA connector bridge on Realview EBLinus Walleij1-24/+40
The PL111 in the ARM reference platforms are connected to "panels" that are actually dumb VGA DAC connector bridges. Now that we can support the proper bridges in the DRM driver, fix this up. Cc: Mali DP Maintainers <malidp@foss.arm.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20ARM: dts: Augment VGA connector bridge on PB1176Linus Walleij1-26/+40
The PL111 in the ARM reference platforms are connected to "panels" that are actually dumb VGA DAC connector bridges. Now that we can support the proper bridges in the DRM driver, fix this up. Cc: Mali DP Maintainers <malidp@foss.arm.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20ARM: dts: Augment VGA connector bridge on PB11MPcoreLinus Walleij1-25/+53
The PL111 in the ARM reference platforms are connected to "panels" that are actually dumb VGA DAC connector bridges. Now that we can support the proper bridges in the DRM driver, fix this up. Cc: Mali DP Maintainers <malidp@foss.arm.com> Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-03-20ARM: dts: sun9i: cubieboard4: Enable VGA display outputChen-Yu Tsai1-0/+68
The Cubieboard4 has a dumb VGA DAC connected to the output of LCD0, providing VGA output through the onboard VGA connector. The DDC lines are connected to i2c3. The VGA DAC is a GM7123, which is compatible with Analog Devices' ADV7123, except it only takes 3.3V power, and has a lower standby power consumption. The datasheet found online lists "Chengdu GoldTel Electronical Technology Co., Ltd." as its designer. The company changed its name in 2014 to "Chengdu Corpro Technology Co., Ltd.". Their website lists similar ICs, but not actually the GM7123. Enable the display pipeline with the VGA DAC and connector, and i2c3 for DDC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-20ARM: dts: sun9i: Add pinmux settings for LCD0 RGB888 output.Chen-Yu Tsai1-0/+11
The A80 supports RGB888 with H/V sync from LCD0. Add a pinmux setting for the needed pins. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-20ARM: dts: sun9i: Add device nodes for documented display pipelines for A80Chen-Yu Tsai1-0/+381
The Allwinner A80 SoC has 3 display pipelines, of which some parts are documented: - 3x display front ends (FE), documented - 2x display enhancement units (DEU), undocumented - 3x display back ends (BE), documented - 2x dynamic range controller (DRC), undocumented - 2x LCDC/TCONs, documented - 1x LCDC/TCON, undocumented, and probably not useable - 1x HDMI transmitter, undocumented but DesignWare compatible - 1x MERGE block, function unknown This patch adds device nodes for the first 2 documented pipelines: FE0 - DEU0 - - BE0 - DRC0 - TCON0 x FE1 - DEU1 - - BE1 - DRC1 - TCON1 Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19arm: dts: mt7623: add PCIe related nodesRyder Lee2-0/+135
This patch adds some device nodes for the PCIe function block and updates related pinmux. Moreover, we add interrupt-map properties in both parent and children as the chip only has one IRQ per slot that is connected to all INTx and get propagated through the bridges and it also represents the root ports own interrupts. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2018-03-19ARM: dts: sun8i-h3: Add Mali nodeGiulio Benetti1-0/+27
The H3 has an ARM Mali 400 GPU, so add binding to our DT. Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-03-19arm: dts: mt7623: use - instead of _ in DT node nameSean Wang3-34/+34
It should be good that no use "_" is in DT node name. Consequently, those nodes in certain files which have an inappropriate name containing "_" are all being replaced with "-". Signed-off-by: Sean Wang <sean.wang@mediatek.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: devicetree@vger.kernel.org Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2018-03-19arm: dts: mt7623: remove useless property pinctrl-names at node switch@0Sean Wang1-1/+0
The property pinctrl-names is totally superfluous. It would be good to remove the property to keep the node neatness. There is actually unnecessary to set up any pins for data path TRGMII between main SoC and MT7530. Furthermore, it's more reasonable for the pin setup of control path MDIO bus is being placed inside the node of ethernet controller. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2018-03-19arm: dts: mt7623: add related clock properties to cpu[1-3] nodesSean Wang1-0/+9
Complement the missing clock properties cpu[1-3] should depend on. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: linux-pm@vger.kernel.org Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2018-03-19arm: dts: mt7623: enable three available UARTs on bananapi-r2Sean Wang1-2/+11
On bpi-r2 board, totally there're four UARTs which we usually called uart[0-3] helpful to extend slow-I/O devices. Among those ones, uart2 has dedicated pin slot which is used to console log. uart[0-1] appear at the 40-pins connector and uart3 has no pinout, but just has test points (TP47 for TX and TP48 for RX, respectively) nearby uart2, but we don't enable uart3 in the patch. The missing pinctrl is also being supplemented for those newly added devices. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2018-03-19arm: dts: mt7623: fix the regulators mmc should use on bananapi-r2Sean Wang1-4/+13
Both mmc devices on bananapi-r2 board should all use the fixed regulators as their power source instead of PMIC MT6323 exports. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
2018-03-16ARM: dts: silk: Add GPIO keys to DTMagnus Damm1-0/+55
Extend the Silk board support to include SW3, SW4, SW6 and SW12. They are all connected via GPIO lines and handled by the gpio-keys driver. Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-16ARM: dts: silk: Add r1ex24002 EEPROM to DTMagnus Damm1-0/+6
Extend the Silk board support to include U14 which is an I2C based EEPROM hooked up to the I2C1 bus. Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-16ARM: dts: marzen: Add SDHI0 VCCQ RegulatorMagnus Damm1-0/+14
Add support for the on-board voltage regulator hooked up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1 tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V. OUT goes to the pull-ups for the data pins of SDHI0. Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-16ARM: dts: stout: Initial r8a7790 Stout board supportMarek Vasut2-0/+364
Stout base board support making use of 1 GiB of memory, the Renesas H2 r8a7790 SoC with the SCIFA0 serial port and CA15 with ARM architected timer. Furthermore, this device tree contains entries for: - 4x LEDs - SDHI SD/MMC controller - Display unit with HDMI output - SH fast ethernet controller - QSPI controller with S25FL512S attached to it - I2C controller with DA9210 and DA 9063 PMICs Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-16ARM: dts: lager: Move cec_clock to root nodeGeert Uytterhoeven1-6/+6
cec-clock is a fixed clock generator that is not controlled by i2c-12 and thus should not be a child of the i2c-12 bus node. Rather, it should be a child of the root node of the DT. Fixes: c5aa87977626e778 ("ARM: dts: lager: Add CEC clock for HDMI transmitter") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-16ARM: dts: kzm9d: Fix "debounce-interval" property misspellingGeert Uytterhoeven1-4/+4
"debounce_interval" was never supported. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-03-16ARM: dts: stih4xx: Add missing #sound-dai-cellsRob Herring2-0/+2
dtc now gives the following warnings: arch/arm/boot/dts/stih410-b2120.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0]) arch/arm/boot/dts/stih407-b2120.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0]) arch/arm/boot/dts/stih410-b2260.dtb: Warning (sound_dai_property): /soc/sound/simple-audio-card,dai-link@0/codec: Missing property '#sound-dai-cells' in node /soc/sti-display-subsystem/sti-hdmi@8d04000 or bad phandle (referred from sound-dai[0]) Add the missing #sound-dai-cells property. Cc: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
generated by cgit v1.2.3 (git 2.39.0) at 2025-02-24 19:29:50 +0300