| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a couple last-minute fixes for ARM SoCs. Most of them are
for the OMAP platforms, the rest are all for different platforms.
OMAP:
All dts fixes, mostly affecting voltages and pinctrl for various
device drivers:
- Regulator minimum voltage fixes for omap5
- ISP syscon register offset fix for omap3
- Fix regulator initial modes for n900
- Fix omap5 pinctrl wkup instance size
Allwinner:
Remove incorrect constraints from a dcdc1 regulator
Alltera SoCFPGA:
Fix compilation in thumb2 mode
Samsung exynos:
Fix a potential oops in the pm-domain error handling
Davinci:
Avoid a link error if NVMEM is disabled
Renesas:
Do not mark an external uart clock as disabled, to allow probing
the uarts"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: davinci: only use NVMEM when available
ARM: SoCFPGA: Fix secondary CPU startup in thumb2 kernel
ARM: dts: omap5: fix range of permitted wakeup pinmux registers
ARM: dts: omap3-n900: Specify peripherals LDO regulators initial mode
ARM: dts: omap3: Fix ISP syscon register offset
ARM: dts: omap5-cm-t54: fix ldo1_reg and ldo4_reg ranges
ARM: dts: omap5-board-common: fix ldo1_reg and ldo4_reg ranges
arm64: dts: r8a7795: Don't disable referenced optional scif clock
ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
ARM: dts: sun8i-q8-common: Do not set constraints on dc1sw regulator
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.6
A single regulator fix
* tag 'sunxi-fixes-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i-q8-common: Do not set constraints on dc1sw regulator
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v4.6" from Simon Horman:
* Don't disable referenced optional scif clock
* tag 'renesas-fixes2-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7795: Don't disable referenced optional scif clock
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.6-rc cycle. All dts fixes, mostly
affecting voltages and pinctrl for various device drivers:
- Regulator minimum voltage fixes for omap5
- ISP syscon register offset fix for omap3
- Fix regulator initial modes for n900
- Fix omap5 pinctrl wkup instance size
* tag 'omap-for-v4.6/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: fix range of permitted wakeup pinmux registers
ARM: dts: omap3-n900: Specify peripherals LDO regulators initial mode
ARM: dts: omap3: Fix ISP syscon register offset
ARM: dts: omap5-cm-t54: fix ldo1_reg and ldo4_reg ranges
ARM: dts: omap5-board-common: fix ldo1_reg and ldo4_reg ranges
|
|
otherwise we can't define gpio1_wk14
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Without that, regulators are left in the mode last set by the bootloader or
by the kernel the device was rebooted from. This leads to various problems,
like non-working peripherals.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
According to the TRM, SCM CONTROL_CSIRXFE register is on offset 0x6c
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ldo4_reg is connected to DSS, and should always be 1.8V. However the The
dts defines a range of 1.5V-1.8V, which requires somethings to set the
actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ldo4_reg is connected to DSS, and should always be 1.8V. However the
The dts defines a range of 1.5V-1.8V, which requires somethings to set
the actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into fixes
Merge "Qualcomm Fixes for v4.6-rc2" from Andy Gross:
* Revert BAM usage on MSM8974 boards
* tag 'qcom-fixes-for-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"
Revert "dts: msm8974: Add blsp2_bam dma node"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:
Fixes for omaps for v4.6-rc cycle:
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.6" from Simon Horman:
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.6-rc2" from Tony Lindgren
Fixes for omaps against v4.6-rc2, mostly to fix suspend for beagle-x15
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
* tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (198 commits)
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Linux 4.6-rc2
v4l2-mc: avoid warning about unused variable
Convert straggling drivers to new six-argument get_user_pages()
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
net: mvneta: fix changing MTU when using per-cpu processing
...
|
|
This reverts commit 19417bd9c511 ("ARM: dts: porter: Enable SCIF_CLK
frequency and pins") as according to
http://elinux.org/File:R-CarM2-KOELSCH_PORTER-B_PORTER_C_Comparison.pdf
the external oscillator for SCIF_CLK is not mounted on the porter boards.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
clk_get on a disabled clock node will return EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their clocks property.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them to prevent this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
USB1 controller is hardwired to be used as Host only port so
we don't need to check ID pin state and can get rid of extcon_usb1.
This also reduces USB1 controller's and so eSATA power's dependency
with EXTCON. This fixes eSATA port with multi_v7_defconfig.
Cc: Franklin S Cooper Jr. <fcooper@ti.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
[tony@atomide.com: updated to describe what it fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: cce1ee000187 ("ARM: DTS: am437x: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: b5e509066074 ("ARM: DTS: am33xx: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
mvebu fixes for 4.6 (part 1)
- fix USB adress register for Linksys Armada 388 based boards
- fix build warning in mvebu-mbus
* tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps against v4.6-rc1. Mostly minor fixes for the newer
SoCs with few board fixes and a fix for a long time hwmod bug:
- Fix cpsw_emac0 link type for baltos-ir5221
- Fix interrupt type for TWD
- Fix edma memcpy channel allocation for am43x
- Fix am43x-epos sycntimer32k by using the correct assigned clock
- Fix interconnect barrier for dra7
- Fix a long time hwmod bug for updating sysconfig register properly
- Fix flakey booting on dm814x where USB reset needs a delay
And there is one minor change that is not strictly a fix, but is
good to have for proper hardware detection:
- Detect dra7 silicon revision 2.0 properly
* tag 'omap-for-v4.6/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type
ARM: OMAP: Correct interrupt type for ARM TWD
ARM: DRA722: Add ID detect for Silicon Rev 2.0
ARM: dts: am43xx: fix edma memcpy channel allocation
ARM: dts: AM43x-epos: Fix clk parent for synctimer
ARM: OMAP2: Fix up interconnect barrier initialization for DRA7
ARM: OMAP2+: hwmod: Fix updating of sysconfig register
ARM: OMAP2+: Use srst_udelay for USB on dm814x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
|
|
This is w.r.t J6/J6eco: 32clk is pseudo (erratum i856) - clock source.
Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
crystal is not enabled at power up. Instead the CPU falls back to using
an emulation for the 32KHz clock which is SYSCLK1/610. SYSCLK1 is usually
20MHz on boards so far (which gives an emulated frequency of 32.786KHz)
Modelling the same in device tree.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Revert this commit to fix regressions on non-dragonboard MSM8974 boards.
This will be put back in after the correct fixes to the bam driver are
accepted that allow remote processor control of the main control registers.
This reverts commit 0a5d0f85bba61d8643d78869c7c4214d6c2a7ce6.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Revert this commit to fix regressions on non-dragonboard MSM8974 boards.
This will be put back in after the correct fixes to the bam driver are
accepted that allow remote processor control of the main control registers.
This reverts commit 62bc8179222372624fd8a52b88327b962614d7b2.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
In Baltos iR5221 cpsw_emac0 is connected directly to the switch IC and
hence needs to be configured as "fixed-link".
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ARM TWD interrupt is a private peripheral interrupt (PPI) and per
the ARM GIC documentation, whether the type for PPIs can be set is
IMPLEMENTATION DEFINED. For OMAP4 devices the PPI type cannot be set and
so when we attempt to set the type for the ARM TWD interrupt it fails.
This has done unnoticed because it fails silently and because we cannot
re-configure the type it has had no impact. Nevertheless fix the type
for the TWD interrupt so that it matches the hardware configuration.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
EDMA was allocating DMA channels 32 and 33 for memcpy usage, out of which
channel 33 is actually used by DES crypto engine. This bad allocation of
the channel causes a crash in the DES crypto engine, as the channel
gets configured for memcpy usage instead of hardware <-> memory DMA.
Fixed by allocating DMA channels 58 and 59 for memcpy usage (I2C0 RX/TX),
which are not used by anybody.
Fixes: cce1ee000187 ("ARM: DTS: am437x: Use the new DT bindings for
the eDMA3")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Suggested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 55ee7017ee31 ("arm: omap2: board-generic: use omap4_local_timer_init
for AM437x") makes synctimer32k as the clocksource on AM43xx. By default
the synctimer32k is clocked by 32K RTC OSC on AM43xx. But this 32K RTC OSC
is not available on epos boards which makes it fail to boot.
Synctimer32k can also be clocked by a peripheral PLL, so making this as
clock parent for synctimer3k on epos boards.
Fixes: 55ee7017ee31 ("arm: omap2: board-generic: use omap4_local_timer_init for AM437x")
Cc: stable@vger.kernel.org # v4.4+
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Kevin Hilman <khilman@baylibre.com>
|
|
The USB2 port for Armada 38x is defined to be at 58000, not at
50000.
Cc: <stable@vger.kernel.org>
Fixes: 2d0a7addbd10 ("ARM: Kirkwood: Add support for many Synology NAS devices")
Signed-off-by: Patrick Uiterwijk <patrick@puiterwijk.org>
Acked-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
dc1sw is an on/off only regulator and as such it cannot have constraints.
This is a limitation of the kernel regulator implementation which resolves
supplies on the first regulator_get(), which is done after applying
constraints, and applying the constrains will fail because it calls
_regulator_get_voltage() and _regulator_do_set_voltage() both of which
will fail on a switch regulator when there is no supply (yet).
This causes registering of all axp22x regulators to fail with the
following errors:
[ 1.395249] vcc-lcd: failed to get the current voltage(-22)
[ 1.405131] axp20x-regulator axp20x-regulator: Failed to register dc1sw
[ 1.412436] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commit removes the constrains on dc1sw / vcc-lcd fixing this problem
note that dcdc1 itself is contrained to the exact same values, so this
does not change anything.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM DT changes from Arnd Bergmann:
"Here are some final updates for ARM SoC specific dts files:
- The i.MX changes were sent relatively late, and had a dependency on
the clk tree, so I delayed that a bit. Support for the new i.MX6qp
SoC and a couple of new boards is added in this branch.
- Uniphier renames a few files to match the final product names that
were decided by the company, kudos to the kernel developer(s) for
getting support upstream before the product release. Also two
boards are added. The patches were posted early enough and nice
overall, but we forgot to apply them and decided to give it some
more time in linux-next
- at91 has two small bug fixes"
* tag 'armsoc-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: uniphier: add pinmux node for I2C ch4
ARM: dts: uniphier: add @{address} to EEPROM node
ARM: dts: uniphier: add PH1-Pro4 Sanji board support
ARM: dts: uniphier: add PH1-Pro4 Ace board support
ARM: dts: uniphier: enable I2C channel 2 of ProXstream2 Gentil board
ARM: dts: uniphier: add EEPROM node for ProXstream2 Gentil board
ARM: dts: uniphier: add reference clock nodes
ARM: dts: uniphier: rework UniPhier System Bus nodes
ARM: dts: uniphier: factor out ranges property of support card
arm64: dts: uniphier: rename PH1-LD10 to PH1-LD20
ARM: dts: imx53-qsb: Fix gpio button polarity
ARM: dts: vfxxx: Add DAC node for Vybrid SoC
ARM: dts: imx6q: add missing links between ipu2 and mipi dsi
ARM: dts: imx: Add support for Advantech/GE B850v3
ARM: dts: imx: Add support for Advantech/GE B650v3
ARM: dts: imx: Add support for Advantech/GE B450v3
ARM: dts: imx: Add support for Advantech/GE Bx50v3
ARM: dts: imx: Add Advantech BA-16 Qseven module
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt2
Merge "First fixes batch for AT91 on 4.6 - DT only fixes" from Nicolas Ferre:
- prevent the boards from having glitches when inserting/removing SD card on
sama5d3/d4 Xplained. The regulators should be kept on.
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
|
|
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 8d545f32bd77 ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
If enabling the hsmci regulator on card detection, the board can reboot
on sd card insertion. Keeping the regulator always enabled fixes this
issue.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: 1b53e3416dd0 ("ARM: at91/dt: sama5d3 xplained: add fixed regulator for vmmc0")
Cc: stable@vger.kernel.org #4.3 and later
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
plus a couple of related 64-bit updates:
New SoC support:
- Allwinner A83T
- Axis Artpec-6 SoC
- Mediatek MT7623 SoC
- TI Keystone K2G SoC
- ST Microelectronics stm32f469
New board or machine support:
- ARM Juno R2
- Buffalo Linkstation LS-QVL and LS-GL
- Cubietruck plus
- D-Link DIR-885L
- DT support for ARM RealView PB1176 and PB11MPCore
- Google Nexus 7
- Homlet v2
- Itead Ibox
- Lamobo R1
- LG Optimus Black
- Logicpd dm3730
- Raspberry Pi Model A
Other changes include
- Lots of updates for Qualcomm APQ8064, MSM8974 and others
- Improved support for Nokia N900 and other OMAP machines
- Common clk support for lpc32xx
- HDLCD display on ARM
- Improved stm32f429 support
- Improved Renesas device support, r8a779x and others
- Lots of Rockchip updates
- Samsung cleanups
- ADC support for Atmel SAMA5D2
- BCM2835 (Raspberry Pi) improvements
- Broadcom Northstar Plus enhancements
- OMAP GPMC rework
- Several improvements for Atmel SAMA5D2 / Xplained
- Global change to remove inofficial "arm,amba-bus" compatible
string"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (350 commits)
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus"
ARM: dts: artpec: dual-license on artpec6.dtsi
ARM: dts: ux500: add synaptics RMI4 for Ux500 TVK DT
arm64: dts: juno/vexpress: fix node name unit-address presence warnings
arm64: dts: foundation-v8: add SBSA Generic Watchdog device node
ARM: dts: at91: sama5d2 Xplained: add leds node
ARM: dts: at91: sama5d2 Xplained: add user push button
ARM: dts: at91: sama5d2 Xplained: set pin muxing for usb gadget and usb host
ARM: dts: stm32f429: Enable Ethernet on Eval board
ARM: dts: omap3-sniper: TWL4030 keypad support
Revert "ARM: dts: DRA7: Add dt nodes for PWMSS"
ARM: dts: dm814x: dra62x: Disable wait pin monitoring for NAND
ARM: dts: dm814x: dra62x: Fix NAND device nodes
ARM: dts: stm32f429: Add Ethernet support
ARM: dts: stm32f429: Add system config bank node
ARM: dts: at91: sama5d2: add nand0 and nfc0 nodes
ARM: dts: at91: sama5d2: add dma properties to UART nodes
ARM: dts: at91: sama5d2 Xplained: Correct the macb irq pinctrl node
ARM: dts: exynos: Don't overheat the Odroid XU3-Lite on high load
ARM: dts: exynos: Add cooling levels for Exynos5422/5800 CPUs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
|
|
This will be needed for UniPhier PH1-LD11 and PH1-LD20 SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Just for consistent coding style.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Initial commit for PH1-Pro4 Sanji board support.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Initial commit for PH1-Pro4 Ace board support.
Note:
There are two variants for the amount of DDR memory; 1GB or 2GB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This is used for on-board inter-connection.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This board has an EEPROM (STMicroelectronics M24C64-WMN6TP) connected
to the I2C channel 0 of the SoC. Its slave address is 0x54.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add master clock nodes generated by crystal oscillators.
PH1-sLD3, PH1-LD4: 24.576 MHz
PH1-Pro4, ProXstream2: 25.000 MHz
PH1-Pro5: 20.000 MHz
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
During the review process of the UniPhier System Bus driver
(drivers/bus/uniphier.c), the current binding of the System Bus
Controller turned out to be no good. In order to make the driver
really usable, we have to switch over to the new binding defined by
Documentation/devicetree/bindings/bus/uniphier-system-bus.txt.
The old binding will be still supported for a while to keep the
backward compatibility.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This property is used in common by several boards. Move it to the
common place (uniphier-support-card.dtsi). If necessary, each board
can still override the property.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big char/misc driver update for 4.6-rc1.
The majority of the patches here is hwtracing and some new mic
drivers, but there's a lot of other driver updates as well. Full
details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (238 commits)
goldfish: Fix build error of missing ioremap on UM
nvmem: mediatek: Fix later provider initialization
nvmem: imx-ocotp: Fix return value of imx_ocotp_read
nvmem: Fix dependencies for !HAS_IOMEM archs
char: genrtc: replace blacklist with whitelist
drivers/hwtracing: make coresight-etm-perf.c explicitly non-modular
drivers: char: mem: fix IS_ERROR_VALUE usage
char: xillybus: Fix internal data structure initialization
pch_phub: return -ENODATA if ROM can't be mapped
Drivers: hv: vmbus: Support kexec on ws2012 r2 and above
Drivers: hv: vmbus: Support handling messages on multiple CPUs
Drivers: hv: utils: Remove util transport handler from list if registration fails
Drivers: hv: util: Pass the channel information during the init call
Drivers: hv: vmbus: avoid unneeded compiler optimizations in vmbus_wait_for_unload()
Drivers: hv: vmbus: remove code duplication in message handling
Drivers: hv: vmbus: avoid wait_for_completion() on crash
Drivers: hv: vmbus: don't loose HVMSG_TIMER_EXPIRED messages
misc: at24: replace memory_accessor with nvmem_device_read
eeprom: 93xx46: extend driver to plug into the NVMEM framework
eeprom: at25: extend driver to plug into the NVMEM framework
...
|
