| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
[ Upstream commit 94a82284ad4711b7f9fd78981fdc7a1cb645030b ]
Remove unused #address-cells and #size-cells from pinmux
node. This fixes W=1 warnings of the type:
arch/arm/boot/dts/da850-lcdk.dtb: Warning (avoid_unnecessary_addr_size): /soc@1c00000/pinmux@14120: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Tested on DA850 LCDK by checking output of:
/sys/kernel/debug/pinctrl/1c14120.pinmux-pinctrl-single/pins
before and after the change.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d4b78db6ac3e084e2bdc57d5518bd247c727f396 ]
The HDMI encoder is connected to the RGB output of the DU, which is
port@0, not port@1. Fix the incorrect DT description.
Fixes: c5af8a4248d3 ("ARM: dts: porter: add DU DT support")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2bada7ac1fdcbf79a9689bd2ff65fa515ca7a31f ]
The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
Signed-off-by: Aapo Vienamo <aapo@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7981190fb5dd710dea08c2613cee3d05e795ca5e ]
The used part does contain an eeprom compatible with an Atmel 24c02
chip and it is from NXP, but it is not called 24c02. It's actually a
se97b chip. Adjust the compatible accordingly.
Fixes: 21dd0ece34c2 ("ARM: dts: at91: add devicetree for the Axentia TSE-850")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1a012cb2569f2031b3636232c3ab21c20c92d281 ]
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13
carry altenate function, ALT5 for ARM JTAG
Fixes: 21ff843931b2 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Henry Zhang <henryzhang62@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 79c81facdc0b43b1cef37b8d5689a8c8b78f8be0 ]
Since 517e7a1537a ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537a ("ASoC: bcm2835: move to use the clock framework")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f4aa1bd5b4fc80f5f4ecd184caad832fd62c25f7 ]
Correct vpo_sd_1v8_3v3 regulator max voltage to 3.3V
Fixes: 9868bc585ae2 ("ARM: dts: Add support for dra718-evm")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6d97d5aba08b26108f95dc9fb7bbe4d9436c769c ]
Fixes the warning "GIC: PPI13 is secure or misconfigured" by
changing the interrupt type from level_low to edge_raising
Signed-off-by: Philipp Puschmann <pp@emlix.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4e943a890cef42e90f43ce6be64728a290b97c55 ]
dtc now gives the following warning:
arch/arm/boot/dts/rk3288-tinker.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /hdmi@ff980000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 808b7de86a0c19582a7efce4c80d6b4e1da7f370 ]
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0a5aff64f20d92c5a6e9aeed7b5950b0b817bcd9 ]
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DualLite/Solo RQS
[ Upstream commit c0c6bb2322964bd264b4ddedaa5776f40c709f0c ]
This patch fixes the wrongly included dtsi file which
was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
As per the board name, the correct file should be imx6dl.dtsi instead
of imx6q.dtsi
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 7a9caba55a61 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e78c637127ee7683d606737f2e62b5da6fd7b1c3 ]
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Fixes: 187d7967a5ee ("ARM: dts: rockchip: add the sdio/sdmmc node for rk3036")
Fixes: faea098e1808 ("ARM: dts: rockchip: add core rk3036 dtsi")
Fixes: 9848ebeb952d ("ARM: dts: rockchip: add core rk3228 dtsi")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 970656b3246d30955894951ed16bd658e42d8c24 ]
The two usb-otg regulators for imx7d-sdb are both called
"regulator-usb-otg1-vbus" and they effectively override each other.
This is most likely a copy-paste error.
Fixes: b877039aa1fe ("ARM: dts: imx7d-sdb: Adjust the regulator nodes")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a06757dcc8509c162ac00488c8c82fc98e04227 upstream.
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since
it's the appropriate compatible string. Remove the
atmel,at91rm9200-pinctrl compatible string, this fallback is
useless, there are too many changes.
Signed-off-by: Santiago Esteban <Santiago.Esteban@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #v3.18
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6f4870753f29edf7dc39444246f9e39987b8b158 upstream.
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 6cbfdd73a94f ("ARM: dts: add sysmmu nodes for exynos5250")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8fd0adf105e132fd84545997bbef3d5edc2c9c1 upstream.
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0629a01920c0f8a3f825361b24863d760610884a upstream.
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org
Fixes: f4ff257cd160 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c5a88cd2e1c508868922bafa0a5c3365986b98e5 upstream.
This fixes the battery voltage monitoring gpio-hog settings.
When the gpio is low, it turns off the battery voltage to the ADC chip.
However, this needs to be on all of the time so that we can monitor
battery voltage.
Also, there was a typo that prevented pinmuxing from working correctly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d5c7b4d5ac2237a6da7ced3adfe6b8bf769f8cc6 ]
Commit a22950c888e3 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2f1f60c4b903f0f5464560783655ff74c9663a92 which was
commit 7be4b5dc7ffa9499ac6ef33a5ffa9ff43f9b7057 upstream.
It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 0ed43f944a4070d04eddacded8629d0ddb9c8003 which was
comit e153db03c6b7a035c797bcdf35262586f003ee93 upstream.
It requires a driver that was not merged until 4.16, so remove it from
this stable tree as it is pointless.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aac4619d028e2c444ac1217fc2d05b0322079dff upstream.
Set powerhold property for tps65917
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70b8d21496758dd7ff600ec9de0ee3812fac7a40 upstream.
This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi
* reg_aldo2: 2,5V, powers the IO of the RTL8211E
* reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E
* reg_dldo2: 2,8V, powers the analog part of the csi
* reg_dldo3: 3,3V, powers misc
* reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
This patch updates also the vmmc-supply properties on the mmc0 and mmc2
node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we
don't need it anymore.
Fixes: 7daa21370075 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b23af6ad8d2f708c4c3f92dd8f82c233247ba8bf upstream.
The eldoin is supplied from the dcdc1 regulator. The N_VBUSEN pin is
connected to an external power regulator (SY6280AAC).
With this commit we update the pmic binding properties to support
those features.
Fixes: 7daa21370075 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e40ed274489a5f516da120186578eb379b452ac6 ]
Fixes a warning when building with W=1.
All of the ASPEED device trees build without warnings now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7be4b5dc7ffa9499ac6ef33a5ffa9ff43f9b7057 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2b9 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e153db03c6b7a035c797bcdf35262586f003ee93 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d0562 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1b377924841df1e13ab5b225be3a83f807a92b52 ]
Trats2 uses gpf2-1 as the panel reset GPIO. gpy4-5 was only used
on early revisions of the board.
Fixes: 420ae8451a22 ("ARM: dts: exynos4412-trats2: add panel node")
Signed-off-by: Simon Shields <simon@lineageos.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d72f4f03854d1225c72d682bf0e01377e7016419 ]
cec-clock is a fixed clock generator that is not controlled by i2c5 and
thus should not be a child of the i2c5 bus node. Rather, it should be
a child of the root node of the DT.
Fixes: 02a5ab18d366 ("ARM: dts: koelsch: Add CEC clock for HDMI transmitter")
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 74402055a2d3ec998a1ded599e86185a27d9bbf4 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c27676151 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84c7efd607e7fb6933920322086db64654f669b2 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5ce0bad4ccd04c8a989e94d3c89e4e796ac22e48 upstream.
Rockchip recommends to run the CPU cores only with operations points of
1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default
values instead.
Fixes: 903d31e34628 ("ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 506e8a912661c97b41adc8a286b875d01323ec45 ]
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d364b038bc962f494cffb8f6cb6cddbe41bcb5b6 ]
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca41e244517d6d3f1600c229ff7ca615049c1e9c ]
The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 627395a6f8091c0aa18f49dca7df59ba3ec147ef ]
Fixes the following warnings:
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cd7594ac3281722cb8f10d6f6c7e4287747c7a9d ]
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed011 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3c18bbf3d11d2005da08b57ff26f44ff1c2b12d0 ]
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499b8 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cf87634c8b24e24bf379b8c6807c8b0fb5f23567 ]
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f365 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f365 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 586b2a4befad88cd87b372a1cea01e58c6811ea9 upstream.
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ae72e95b5e4ded145bfc6926ad9457b74e3af41a upstream.
The hifsys and ethsys needs the definition of the reset-cells
property. Fix this.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76a09ce214addb8ddc0f6d50dc1106a5f829e713 upstream.
The ethsys binding misses the reset-cells, this patch
adds this property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5c1037196b9ee75897c211972de370ed1336ec8f upstream.
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5628a8ca14149ba4226e3bdce3a04c3b688435ad upstream.
According to the comment added to exynos_dt_pmu_match[] in commit
8b283c025443 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b062 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f8975cb1b8a36d0839b6365235778dd9df1d04ca upstream.
This fixes the following warning by also sending the flags argument for
gpio controllers:
Property 'cs-gpios', cell 6 is not a phandle reference in
/ahb/apb/spi@e0100000
Fixes: 8113ba917dfa ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cdd10409914184c7eee5ae3e11beb890c9c16c61 upstream.
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f60 updated it incorrectly
while moving from platform code to DT. Fix it.
Cc: stable@vger.kernel.org # v3.10+
Fixes: 6e8887f60f60 ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ffb5b4f248fe53e0361b8cbc2a523b432566442 upstream.
The interrupt-parent of rtc was missing, add it.
Fixes: 8113ba917dfa ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b96a696fb2a8dd1ee4e6cfee48dcac270fc53287 upstream.
Fix that bananapi-r2 booting from SD-card would fail since incorrect
polarity is applied to the previous setup with GPIO_ACTIVE_HIGH.
Cc: stable@vger.kernel.org
Fixes: 0eed8d097612 ("arm: dts: mt7623: Add SD-card and EMMC to bananapi-r2")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e8bfa0422469cdfc86be3f525f621b1d44d2481b upstream.
The clcd device is lacking an interrupt-parent property, which makes
the interrupt unusable and shows up as a warning with the latest
dtc version:
arch/arm/boot/dts/ste-nomadik-s8815.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
arch/arm/boot/dts/ste-nomadik-nhk15.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
I looked up the old board files and found that this interrupt has
the same irqchip as all the other on-chip device, it just needs one
extra line.
Fixes: 17470b7da11c ("ARM: dts: add the CLCD LCD display to the NHK15")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
