| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
"make dtbs_check":
arch/arm/boot/dts/vf610-zii-dev-rev-b.dtb: tca9548@70: $nodename:0: 'tca9548@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm/boot/dts/vf610-zii-dev-rev-b.dtb: tca9548@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4' were unexpected)
From schema: /scratch/geert/linux/linux-renesas/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA9548 nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
at86rf230 driver starts with having reset line high, and then drives it
low and then high again, and even calls it "rstn" internally, therefore
it needs to be annotated as "active low" in the DTS.
This will make difference when at86rf230 driver will be converted to
gpiod API that respects declared line polarity.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SFF soldered onto the board expects the port to use 1000BaseX. It
makes no sense to have the port set to SGMII, since it doesn't even
support that mode.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The devicetree specification recommends using generic node names.
Some Zii dts files already follow such recommendation, but some don't,
so use generic node names for consistency among the Zii dts files.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove unnecessary #address-cells/#size-cells from the switch nodes
to fix the following DTC warnings:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "i.MX device tree changes for 4.16" from Shawn Guo:
- A few random updates for vf610-zii board: correct switch EEPROM size,
enable edma1, correct GPIO expander interrupt, add PHYs for switch2
device.
- LS1021A device tree updates: add reboot and QSPI device nodes, label
USB controllers, specify interrupt-affinity for PMU, fix TMR_FIPER1
setting, enable esdhc device, add Moxa UC-8410A board support.
- A bunch of patches from Fabio: fix reg - unit address mismatches,
remove leading zero in unit address, move regulators out of
simple-bus, move nodes with no reg property out of bus, remove extra
clock cell, add missing phy-cells to usb-nop-xceiv, etc.
- A couple series from Hummingboard developers: re-organise device tree
files for better handling various board versions, and then add the
new hummingboard2 board support on top of that.
- Disable AC'97 input pins pad and add support for powering off for
imx6qdl-udoo board.
- Convert from fbdev to drm bindings for imx6sx-sdb and imx6sl-evk
board.
- Add device tree for Variscite DART-MX6 SoM and Carrier-board support.
- Add new board support of TS-4600 and TS-7970 from Technologic
Systems.
- A series from Stefan to update imx7-colibri device tree and then add
new version of Toradex Colibri iMX7D board with eMMC support.
- Other random updates on various board support.
* tag 'imx-dt-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (126 commits)
ARM: dts: imx7s: Avoid using label in unit address and reg
ARM: dts: imx51-zii-rdu1: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: imx6qdl-hummingboard2: Remove leading zero in unit address
ARM: dts: ls1021a: add support for Moxa UC-8410A open platform
ARM: dts: imx51-babbage: Fix the 26MHz clock modelling
ARM: dts: vf610-zii-dev-rev-b: add PHYs for switch2
ARM: dts: vf610-zii-dev-rev-b: fix interrupt for GPIO expander
ARM: dts: vf610-zii-dev: enable edma1
ARM: dts: ls1021a-twr: Remove extra clock cell
ARM: dts: ls1021a-qds: Remove extra clock cell
ARM: dts: imx53: add srtc node
dt-bindings: imx-gpcv2: Fix the unit address
ARM: imx: dts: Use lower case for bindings notation
ARM: dts: imx6q-h100: use usdhc2 VSELECT
ARM: dts: imx6sx: Add support for PCI power domain
ARM: dts: imx6sx: Fix PCI non-prefetchable memory range
ARM: dts: imx6qdl-hummingboard2: rename regulators to match schematic
ARM: dts: imx6qdl-hummingboard2: add v1.5 som with eMMC
ARM: dts: imx6qdl-hummingboard2: add v1.5 som without eMMC
ARM: dts: imx6qdl-hummingboard2: add PWM3 support
...
|
|
The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.
Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull networking fixes from David Miller:
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
|
|
Use XAUI rather than XGMII for DSA link ports, as this is the interface
mode that the switches actually use. XAUI is the 4 lane bus with clock
per direction, whereas XGMII is a 32 bit bus with clock.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.
Fixes: d4cd158176c3 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The PHYs embedded in the switch direct there interrupts through the
switch interrupt controllers. Now that devel C has its switch
interrupts connected to the SoC, the PHY interrupts can be used by
phylib. Explicitly include MDIO nodes in the switch device tree nodes,
and link the PHY interrupts back to the switch interrupt
controller. Also, link the ports to the PHYs on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The devel B and devel C board use the same GPIO lines for interrupts
from the two switches. Move the pinmux nodes from devel B into the
shared .dtsi file, and wire up the interrupts on devel C.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ZII Dev Rev C board has EEPROMs hanging the 88E6390 Ethernet switch
chips. Add an "eeprom-length" property to allow access from ethtool.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add .dts file for rev. C of the board by factoring out commonalities
into a shared include file (vf610-zii-dev-rev-b-c.dtsi) and deriving
revision specific file from it (vf610-zii-dev-rev-b.dts and
vf610-zii-dev-reb-c.dts).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: andrew@lunn.ch
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: cphealy@gmail.com
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
