| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220609113911.380368-5-krzysztof.kozlowski@linaro.org
|
|
The binding header provides descriptive names for the RTC clock indexes,
since the indexes were arbitrarily chosen by the binding, not by the
hardware. Let's use the names, so the meaning is clearer.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220607012438.18183-1-samuel@sholland.org
|
|
Several H3 and one H2+ board have power key nodes, which are slightly
off. Some are missing wakeup-source property and some have BTN_0 code
assigned instead of KEY_POWER.
Adjust them, so they can function as intended by designer.
Co-developed-by: Michael Klein <michael@fossekall.de>
Signed-off-by: Michael Klein <michael@fossekall.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211129165510.370717-1-jernej.skrabec@gmail.com
|
|
Bluetooth module on BananaPi M2 Plus can also be used for streaming
audio. However, for that case higher UART speed is required.
Add a max-speed property.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210116105228.847073-1-jernej.skrabec@siol.net
|
|
The Ethernet PHY on the Bananapi M2+ has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 8c7ba536e709 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Fixes: aa8fee415f46 ("ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-8-wens@kernel.org
|
|
The H3 and H5 have never been converted to the new convention we want to
have for the pinctrl nodes.
Convert them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Some nodes still have pinctrl-names entry, yet they don't have any pinctrl
group anymore. Drop them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART1 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, the board's
fixed 3.3V power regulator provides overall power via VBAT and I/O power
via VDDIO. The RTC clock output from the SoC provides the LPO low power
clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Three more variants of the Bananapi M2 Plus have been introduced. One
with the H5 instead of the H3, another with the H2+ instead, and the
last with the H3 but with WiFi and eMMC removed.
All these variants use the same board. This patch splits out the
non-SoC-specific parts of the device tree, so that they can be shared
among all the variants. The original Bananapi M2 Plus has been renamed
to Bananapi M2 Plus H3.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
