| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
commit 1b0e32753d8550908dff8982410357b5114be78c upstream.
The property is "fsl,pins", not "fsl,pin". Wrong property means the pin
configuration was not applied. Fixes dtbs_check warnings:
imx6ul-geam.dtb: pinctrl@20e0000: tscgrp: 'fsl,pins' is a required property
imx6ul-geam.dtb: pinctrl@20e0000: tscgrp: 'fsl,pin' does not match any of the regexes: 'pinctrl-[0-9]+'
Cc: stable@vger.kernel.org
Fixes: a58e4e608bc8 ("ARM: dts: imx6ul-geam: Add Engicam IMX6UL GEA M6UL initial support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0e49cfe364dea4345551516eb2fe53135a10432b ]
There is no "fsl,phy" property in pin controller pincfg nodes:
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,pins' is a required property
imx7d-zii-rmu2.dtb: pinctrl@302c0000: enet1phyinterruptgrp: 'fsl,phy' does not match any of the regexes: 'pinctrl-[0-9]+'
Fixes: f496e6750083 ("ARM: dts: Add ZII support for ZII i.MX7 RMU2 board")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 8512fbb64b0e599412da661412d10d4ba1cb003c upstream.
On the imx6dl-yapp4 revision based boards, the RGB LED is not driven
directly by the LP5562 driver but through FET transistors. Hence the LED
current is not determined by the driver but by the LED series resistors.
On the imx6dl-yapp43 revision based boards, we removed the FET transistors
to drive the LED directly from the LP5562 but forgot to tune the output
current to match the previous HW design.
Set the LED current on imx6dl-yapp43 based boards to the same values
measured on the imx6dl-yapp4 boards and limit the maximum current to 20mA.
Fixes: 7da4734751e0 ("ARM: dts: imx6dl-yapp43: Add support for new HW revision of the IOTA board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit df35c6e9027cf9affe699e632a48082ab1bbba4c ]
The PCIe reset line is active low. Fix it.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 74e1c956a68a65d642447d852e95b3fbb69bebaa ]
There is a comment in the imx6q variant dtsi claiming that these
modules will have one more chip select than the imx6dl variant.
This is wrong. Ordinary GPIOs are used for chip selects and both
variants of the module share the very same PCB and both have this
GPIO routed to the SPI0_CS1# pin of the SMARC connector.
Fix it by moving the third chip select description to the common dtsi.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit b972d6b3b46345023aee56a95df8e2c137aa4ee4 ]
On i.MX6 the board is reset by the watchdog. But in turn to do a
complete board reset, we have to assert the WDOG_B output which is
routed also to the CPLD which then do a complete power-cycle of the
board.
Fixes: 2125212785c9 ("ARM: dts: imx6qdl-kontron-samx6i: add Kontron SMARC SoM Support")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit edfea889a049abe80f0d55c0365bf60fbade272f ]
The PHY reset line is connected to both the SoC (GPIO1_25) and
the CPLD. We must not use the GPIO1_25 as it will drive against
the output buffer of the CPLD. Instead there is another GPIO
(GPIO2_01), an input to the CPLD, which will tell the CPLD to
assert the PHY reset line.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0df3c7d7a73d75153090637392c0b73a63cdc24a ]
The i.MX6 cannot add any RGMII delays. The PHY has to add both the RX
and TX delays on the RGMII interface. Fix the interface mode. While at
it, use the new phy-connection-type property name.
Fixes: 5694eed98cca ("ARM: dts: imx6qdl-kontron-samx6i: move phy reset into phy-node")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d7f3040a565214a30e2f07dc9b91566d316e2d36 ]
Our Tarragon platform uses a active-low signal to inform
the i.MX6ULL about the over-current detection.
Fixes: 5e4f393ccbf0 ("ARM: dts: imx6ull: Add chargebyte Tarragon support")
Signed-off-by: Michael Heimpold <michael.heimpold@chargebyte.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit 135f218255b28c5bbf71e9e32a49e5c734cabbe5 upstream.
Since commit 63b0cd30b78e ("media: ov2680: Add bus-cfg / endpoint
property verification") the ov2680 no longer probes on a imx7s-warp7:
ov2680 1-0036: error -EINVAL: supported link freq 330000000 not found
ov2680 1-0036: probe with driver ov2680 failed with error -22
Fix it by passing the required 'link-frequencies' property as
recommended by:
https://www.kernel.org/doc/html/v6.9-rc1/driver-api/media/camera-sensor.html#handling-clocks
Cc: stable@vger.kernel.org
Fixes: 63b0cd30b78e ("media: ov2680: Add bus-cfg / endpoint property verification")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 79978bff2e4b8e05ebdf5fc3ee6b794002393484 ]
We identified that the PHYs actually do not work since commit 7da7b84fee58
("ARM: dts: imx6dl-yapp4: Move phy reset into switch node") as
a coincidence of several circumstances.
The reset signal is kept asserted by a pull-down resistor on the board
unless it is deasserted by GPIO from the SoC. This is to keep the switch
dead until it is configured properly by the kernel and user space.
Prior to the referenced commit the switch was reset by the FEC driver
and the reset GPIO was actively deasserted. The mdio-bus was scanned
and the attached switch and its PHYs were found and configured.
With the referenced commit the switch is reset by the qca8k driver.
Because of another bug in the qca8k driver, functionality of the reset
pin depends on its pre-kernel configuration. See commit c44fc98f0a8f
("net: dsa: qca8k: fix illegal usage of GPIO")
The problem did not appear until we removed support for the switch
and configuration of its reset pin from the bootloader.
To fix that, properly describe the internal mdio-bus configuration of
the qca8334 switch. The PHYs are internal to the switch and sit on its
internal mdio-bus.
Fixes: 7da7b84fee58 ("ARM: dts: imx6dl-yapp4: Move phy reset into switch node")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 023bd910d3ab735459f84b22bb99fb9e00bd9d76 ]
This change does not have any functional effect. The switch works just
fine without this patch as it has full access to all the addresses
on the bus. This is simply a clean-up to set the node name address
and reg address to the same value.
Fixes: 15b43e497ffd ("ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 96fd598e9c34cfa68402a4da3020c9236cfacf35 ]
The dtc interrupt_provider warning is off by default. Fix all the warnings
so it can be enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20240213-arm-dt-cleanups-v1-2-f2dee1292525@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 8412c47d68436b9f9a260039a4a773daa6824925 ]
Since commit 26c9d152ebf3 ("dt-bindings: tpm: Consolidate TCG TIS
bindings"), several issues are reported by "make dtbs_check" for ARM
devicetrees:
The nodename needs to be "tpm@0" rather than "tpmdev@0" and the
compatible property needs to contain the chip's name in addition to the
generic "tcg,tpm_tis-spi" or "tcg,tpm-tis-i2c":
tpmdev@0: $nodename:0: 'tpmdev@0' does not match '^tpm(@[0-9a-f]+)?$'
from schema $id: http://devicetree.org/schemas/tpm/tcg,tpm_tis-spi.yaml#
tpm@2e: compatible: 'oneOf' conditional failed, one must be fixed:
['tcg,tpm-tis-i2c'] is too short
from schema $id: http://devicetree.org/schemas/tpm/tcg,tpm-tis-i2c.yaml#
Fix these schema violations.
Aspeed Facebook BMCs use an Infineon SLB9670:
https://lore.kernel.org/all/ZZSmMJ%2F%2Fl972Qbxu@fedora/
https://lore.kernel.org/all/ZZT4%2Fw2eVzMhtsPx@fedora/
https://lore.kernel.org/all/ZZTS0p1hdAchIbKp@heinlein.vulture-banana.ts.net/
Aspeed Tacoma uses a Nuvoton NPCT75X per commit 39d8a73c53a2 ("ARM: dts:
aspeed: tacoma: Add TPM").
phyGATE-Tauri uses an Infineon SLB9670:
https://lore.kernel.org/all/ab45c82485fa272f74adf560cbb58ee60cc42689.camel@phytec.de/
A single schema violation remains in am335x-moxa-uc-2100-common.dtsi
because it is unknown which chip is used on the board. The devicetree's
author has been asked for clarification but has not responded so far:
https://lore.kernel.org/all/20231220090910.GA32182@wunner.de/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 858d83ca4b50bbc8693d95cc94310e6d791fb2e6 ]
Per fsl,mxs-dma.yaml, the node name should be 'dma-controller'.
Change it to fix the following dt-schema warning.
imx28-apf28.dtb: dma-apbx@80024000: $nodename:0: 'dma-apbx@80024000' does not match '^dma-controller(@.*)?$'
from schema $id: http://devicetree.org/schemas/dma/fsl,mxs-dma.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit e3aa1a82fb20ee97597022f6528823a8ab82bde6 ]
The 'gpios' property to describe the SDA and SCL GPIOs is considered
deprecated according to i2c-gpio.yaml.
Switch to the preferred 'sda-gpios' and 'scl-gpios' properties.
This fixes the following schema warnings:
imx23-sansa.dtb: i2c-0: 'sda-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
imx23-sansa.dtb: i2c-0: 'scl-gpios' is a required property
from schema $id: http://devicetree.org/schemas/i2c/i2c-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit dc35e253d032b959d92e12f081db5b00db26ae64 ]
Per leds-gpio.yaml, the led names should start with 'led'.
Change it to fix the following dt-schema warning:
imx27-apf27dev.dtb: leds: 'user' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/leds/leds-gpio.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 11ab7ad6f795ae23c398a4a5c56505d3dab27c4c ]
Per display-timings.yaml, the 'timing' pattern should be used to
describe the display timings.
Change it accordingly to fix the following dt-schema warning:
imx27-apf27dev.dtb: display-timings: '800x480' does not match any of the regexes: '^timing', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/panel/display-timings.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f0b929f58719fc57a4926ab4fc972f185453d6a5 ]
Per imx-iim.yaml, the compatible string should only contain a single
entry.
Use it as "fsl,imx25-iim" to fix the following dt-schema warning:
imx25-karo-tx25.dtb: efuse@53ff0000: compatible: ['fsl,imx25-iim', 'fsl,imx27-iim'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/imx-iim.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c248e535973088ba7071ff6f26ab7951143450af ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
The node name should be sram.
Change the node name and pass the required properties to fix the
following dt-schema warnings:
imx1-apf9328.dtb: esram@300000: $nodename:0: 'esram@300000' does not match '^sram(@.*)?'
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
imx1-apf9328.dtb: esram@300000: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/sram/sram.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 2fb7b2a2f06bb3f8321cf26c33e4e820c5b238b6 ]
Per sram.yaml, address-cells, size-cells and ranges are mandatory.
Pass them to fix the following dt-schema warnings:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 1e1d7cc478fb16816de09740e3c323c0c188d58f ]
Per mtd-physmap.yaml, 'nor@0,0' is not a valid node pattern.
Change it to 'flash@0,0' to fix the following dt-schema warning:
imx1-ads.dtb: nor@0,0: $nodename:0: 'nor@0,0' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/mtd-physmap.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 68c711b882c262e36895547cddea2c2d56ce611d ]
Node names should be generic. Use 'rtc' as node name to fix
the following dt-schema warning:
imx25-eukrea-mbimxsd25-baseboard.dtb: pcf8563@51: $nodename:0: 'pcf8563@51' does not match '^rtc(@.*|-([0-9]|[1-9][0-9]+))?$'
from schema $id: http://devicetree.org/schemas/rtc/nxp,pcf8563.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 4aadb841ed49bada1415c48c44d21f5b69e01299 ]
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx7s-mba7.dtb: nand-controller@33002000:
#size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 0d4ac04fa7c3f6dc263dba6f575a2ec7a2d4eca8 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit b76bbf835d8945080b22b52fc1e6f41cde06865d upstream.
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Cc: stable@vger.kernel.org
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 63ef8fc9bcee6b73ca445a19a7ac6bd544723c9f ]
Per root-node.yaml, 'model' is a required property.
Pass it to fix the following dt-schema warning:
imx28-xea.dtb: /: 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fixes: 445ae16ac1c5 ("ARM: dts: imx28: Add DTS description of imx28 based XEA board")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 397caf68e2d36532054cb14ae8995537f27f8b61 ]
The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".
Fixes: 949673450291 ("ARM: dts: add imx7d soc dtsi file")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Roland Hieber <rhi@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit d951f8f5f23a9417b7952f22b33784c73caa1ebb ]
Since commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.
This caused Ethernet to stop working.
Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.
Fixes: c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK specific PHY fixup")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit 6552218f4dc47ba3c6c5b58cc1e9eb208a2b438b ]
A regression was introduced in the Skov specific i.MX6 flavor
reve-mi1010ait-1cp1 device tree causing the external ethernet controller
to not being selected as the clock source for the i.MX6 ethernet MAC,
resulting in a none functional ethernet interface. The root cause is
that the ethernet clock selection is now part of the clocks node, which
is overwritten in the specific device tree and wasn't updated to contain
these ethernet clocks.
Fixes: c89614079e44 ("ARM: dts: imx6qdl-skov-cpu: configure ethernet reference clock parent")
Signed-off-by: Stefan Kerkmann <s.kerkmann@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
|
|
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20230823085146.113562-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Numbers are separated by dashes. Fixes the warnings:
arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dtb: gpio-buttons: 'button1',
'button2', 'button3' do not match any of the regexes:
'^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/input/gpio-keys.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
nand-controller.yaml bindings says #size-cells shall be set to 0.
Fixes the dtbs_check warning:
arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dtb:
nand-controller@1806000: #size-cells:0:0: 0 was expected
from schema $id: http://devicetree.org/schemas/mtd/gpmi-nand.yaml#
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
interrupt-controller is only valid for gpio subnode, remove it.
Rename touchscreen subnode according to bindings.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Per simple-card.yaml, 'simple-audio-card,audio-routing' is not a valid
property.
Change it to 'simple-audio-card,routing'.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Wifi chip description, which causes the following schema warning:
imx6q-prti6q.dtb: mmc@2194000: Unevaluated properties are not allowed ('wifi' was unexpected)
Pass the missing items to fix it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pass 'mmc' as the esdhc node names to fix the following schema
warnings:
vf610-cosmic.dtb: esdhc@400b1000: $nodename:0: 'esdhc@400b1000' does not match '^mmc(@.*)?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
"st,m25p" is not a valid compatible according to jedec,spi-nor.yaml.
Remove it.
Also, node names should be generic, so use 'flash' as the SPI NOR flash
node name.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node names should be generic, so use 'flash' as the SPI NOR flash node
name.
This fixes the following schema warning:
imx53-smd.dtb: m25p32@1: $nodename:0: 'm25p32@1' does not match '^(flash|.*sram|nand)(@.*)?$'
from schema $id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
"st,m25p" is not a valid compatible according to jedec,spi-nor.yaml.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The bootloader does not add the partitions into DT, so add them manually
here.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device tree for the MBLS102xA mainboard with TQMLS1021A SoM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Passing the 'compatible' property inside the pfuze100 regulator nodes
is not allowed per pfuze100.yaml and results in the following
warning:
imx6q-bosch-acc.dtb: pmic@8: regulators:sw3a: Unevaluated properties are not allowed ('compatible' was unexpected)
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As per sgtl5000.yaml, '#sound-dai-cells' is a required property.
Pass it to fix the following schema warnings:
imx53-mba53.dtb: sgtl5000@a: '#sound-dai-cells' is a required property
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Each interrupt should be in its own cell. This is much more readable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
As per sgtl5000.yaml, 'clock-names' is not a valid property.
Remove it to fix the following schema warning:
imx6ul-isiot-nand.dtb: codec@a: Unevaluated properties are not allowed ('clock-names' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
If the tuning step is not set, the tuning step is set to 1.
For some sd cards, the following Tuning timeout will occur.
Tuning failed, falling back to fixed sampling clock
So set the default tuning step. This refers to the NXP vendor's
commit below:
https://github.com/nxp-imx/linux-imx/blob/lf-6.1.y/
arch/arm/boot/dts/imx6sx.dtsi#L1108-L1109
Fixes: 1e336aa0c025 ("mmc: sdhci-esdhc-imx: correct the tuning start tap and step setting")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
