summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/meson8b-odroidc1.dts
AgeCommit message (Collapse)AuthorFilesLines
2019-12-11ARM: dts: meson: provide the XTAL clock using a fixed-clockMartin Blumenstingl1-1/+1
The clock controller driver has provided the XTAL clock so far. This does not match how the hardware actually works because the XTAL clock is an actual crystal which is mounted on the PCB. Add the "xtal" clock to meson.dtsi and replace all references to the clock controller's CLKID_XTAL with the new xtal clock node. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-08-12ARM: dts: meson8b: odroidc1: use the MAC address stored in the eFuseMartin Blumenstingl1-0/+9
Odroid-C1 uses the MAC address stored in eFuse at offset 0x1b4 (which is defined as a "standard" offset for all Meson8 and Meson8b boards, but testing shows that MXQ doesn't have the eFuse values programmed and EC-100 stores it's MAC address in eMMC). Add the nvmem cell which points to the MAC address and asssign it to the Ethernet controller as "mac-address". As result of this the MAC address which is stored in the eFuse is now assigned to the Ethernet controller and consistent across reboots. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-08-06ARM: dts: meson8b: odroidc1: add the VDDEE regulatorMartin Blumenstingl1-3/+24
The VDDEE regulator is basically a copy of the VCCK regulator. VDDEE supplies for example the Mali GPU and is controlled by PWM_D instead of PWM_C. Add the VDDEE PWM regulator and make it the supply of the Mali GPU. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-06-20ARM: dts: meson: switch to the generic Ethernet PHY reset bindingsMartin Blumenstingl1-4/+5
The snps,reset-gpio bindings are deprecated in favour of the generic "Ethernet PHY reset" bindings. Replace snps,reset-gpio from the &ethmac node with reset-gpios in the ethernet-phy node. The old snps,reset-active-low property is now encoded directly as GPIO flag inside the reset-gpios property. snps,reset-delays-us is converted to reset-assert-us and reset-deassert-us. reset-assert-us is the second cell from snps,reset-delays-us while reset-deassert-us was the third cell. Instead of blindly copying the old values (which seems strange since they gave the PHY one second to come out of reset) over this also updates the delays based on the datasheets: - RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert delay (the datasheet mentions: "For a complete PHY reset, this pin must be asserted low for at least 10ms") and a 30ms deassert delay (the datasheet mentions: "Wait for a further 30ms (for internal circuits settling time) before accessing the PHY register"). The old settings used 10ms for assert and 1000ms for deassert. - IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock output ready after reset released | 10ms")). The old settings used 10ms for assert and 1000ms for deassert. No functional changes intended. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-06-04ARM: dts: meson8b-odroidc1: update with SPDX Licence identifierNeil Armstrong1-41/+1
While the text specifies "of the GPL or the X11 license" the actual license text matches the MIT license as specified at [0] [0] https://spdx.org/licenses/MIT.html Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-04-16ARM: dts: meson8b: odroid-c1: prepare support for the RTCMartin Blumenstingl1-0/+14
The Odroid-C1 has the 32.768 kHz oscillator (X3 in the schematics) which is required for the RTC. A battery can be connected separately (to the BT1 header) - then the "rtc" node can be enabled manually. By default the RTC is disabled because the boards typically come without the RTC battery. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-03-29ARM: dts: meson8b: odroidc1: add the GPIO line namesMartin Blumenstingl1-0/+52
This adds the GPIO line names from the schematics to get them displayed in the debugfs output of each GPIO controller. The schematics from Odroid-C1+ PCB revision 0.4 20150615 are used as referenced. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-03-06Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/socLinus Torvalds1-0/+6
Pull ARM SoC device tree updates from Arnd Bergmann: "This is a smaller update than the past few times, but with just over 500 non-merge changesets still dwarfes the rest of the SoC tree. Three new SoC platforms get added, each one a follow-up to an existing product, and added here in combination with a reference platform: - Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging processor: https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html - Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics Applications": https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html - NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC: https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X These are actual commercial products we now support with an in-kernel device tree source file: - Bosch Guardian is a product made by Bosch Power Tools GmbH, based on the Texas Instruments AM335x chip - Winterland IceBoard is a Texas Instruments AM3874 based machine used in telescopes at the south pole and elsewhere, see commit d031773169df2 for some pointers: - Inspur on5263m5 is an x86 server platform with an Aspeed ast2500 baseboard management controller. This is for running on the BMC. - Zodiac Digital Tapping Unit, apparently a kind of ethernet switch used in airplanes. - Phicomm K3 is a WiFi router based on Broadcom bcm47094 - Methode Electronics uDPU FTTdp distribution point unit - X96 Max, a generic TV box based on Amlogic G12a (S905X2) - NVIDIA Shield TV (Darcy) based on Tegra210 And then there are several new SBC, evaluation, development or modular systems that we add: - Three new Rockchips rk3399 based boards: - FriendlyElec NanoPC-T4 and NanoPi M4 - Radxa ROCK Pi 4 - Five new i.MX6 family SoM modules and boards for industrial products: - Logic PD i.MX6QD SoM and evaluation baseboad - Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL - Phytec phyCORE i.MX6 UltraLite SoM and evaluation module - MYIR Tech MYD-LPC4357 development based on the NXP lpc4357 microcontroller - Chameleon96, an Intel/Altera Cyclone5 based FPGA development system in 96boards form factor - Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual platform for corresponding to the latest "fast model" - Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit and 64-bit mode. - Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards enterprise form factor - Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108 For already supported boards and SoCs, we often add support for new devices after merging the drivers. This time, the largest changes include updates for - STMicroelectronics stm32mp1, which was now formally launched last week - Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip - Action Semi S700 - TI AM654x, their recently merged 64-bit SoC from the OMAP family - Various Amlogic Meson SoCs - Mediatek MT2712 - NVIDIA Tegra186 and Tegra210 - The ancient NXP lpc32xx family - Samsung s5pv210, used in some older mobile phones Many other chips see smaller updates and bugfixes beyond that" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits) ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4 dt-bindings: net: ti: deprecate cpsw-phy-sel bindings ARM: dts: am335x: switch to use phy-gmii-sel ARM: dts: am4372: switch to use phy-gmii-sel ARM: dts: dm814x: switch to use phy-gmii-sel ARM: dts: dra7: switch to use phy-gmii-sel arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference ARM: dts: exynos: Add support for secondary DAI to Odroid XU4 ARM: dts: exynos: Add support for secondary DAI to Odroid XU3 ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite ARM: dts: exynos: Add stdout path property to Arndale board ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU ARM: dts: exynos: Enable ADC on Odroid HC1 arm64: dts: sprd: Remove wildcard compatible string arm64: dts: sprd: Add SC27XX fuel gauge device arm64: dts: sprd: Add SC2731 charger device arm64: dts: sprd: Add ADC calibration support arm64: dts: sprd: Remove PMIC INTC irq trigger type arm64: dts: rockchip: Enable tsadc device on rock960 ARM: dts: rockchip: add chosen node on veyron devices ...
2019-02-15Merge tag 'amlogic-dt' of ↵Arnd Bergmann1-0/+5
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt ARM: dts: Amlogic updates for v5.1 - more features for Endless EC100 board - chip temperature sensor support - fix ethernet pins - add Mali-450 GPU * tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: dts: meson8b: ec100: add the GPIO line names ARM: dts: meson8b: ec100: improve the description of the regulators ARM: dts: meson8b: ec100: enable the Ethernet PHY interrupt ARM: dts: meson8m2: mxiii-plus: add iio-hwmon for the chip temperature ARM: dts: meson8b: odroidc1: add iio-hwmon for the chip temperature ARM: dts: meson8b: ec100: add iio-hwmon for the chip temperature ARM: dts: meson8b: add the temperature calibration data for the SAR ADC ARM: dts: meson8: add the temperature calibration data for the SAR ADC ARM: dts: meson8m2: use the Meson8m2 specific SAR ADC compatible ARM: dts: meson: switch the clock controller to the HHI register area ARM: dts: meson8b: fix the Ethernet data line signals in eth_rgmii_pins ARM: dts: meson8b: add the Mali-450 MP2 GPU ARM: dts: meson8: add the Mali-450 MP6 GPU dt-bindings: gpu: mali-utgard: add Amlogic Meson8 and Meson8b compatible ARM: dts: meson8b: add the APB bus ARM: dts: meson8: add the APB bus ARM: dts: meson6: add the APB2 bus Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-02-11ARM: dts: meson8b: odroidc1: add iio-hwmon for the chip temperatureMartin Blumenstingl1-0/+5
SAR ADC enabled channel 8 can be used to measure the chip temperature. This can be made available to the hwmon subsystem by using iio-hwmon. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-01-30ARM: dts: Kill off skeleton{64}.dtsiRob Herring1-0/+1
Remove the usage of skeleton.dtsi in the remaining dts files. It was deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated"). This will make adding a unit-address to memory nodes easier. The main tricky part to removing skeleton.dtsi is we could end up with no /memory node at all when a bootloader depends on one being present. I hacked up dtc to check for this condition. Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Antoine Tenart <antoine.tenart@bootlin.com> Acked-by: Alexandre TORGUE <alexandre.torgue@st.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Acked-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-01-11ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-lowMartin Blumenstingl1-2/+1
After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device tree") SD cards are not detected anymore. The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify: "[...] using the "cd-inverted" property means, that the CD line is active high, i.e. it is high, when a card is inserted". Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and drop the "cd-inverted" property. This makes the definition consistent with the existing dt-bindings and fixes the check whether an SD card is inserted. Fixes: e03efbce6bebf5 ("ARM: dts: meson8b-odroidc1: add microSD support") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Anand Moon <linux.amoon@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2019-01-11arm: dts: meson: Fix IRQ trigger type for macirqCarlo Caione1-1/+0
A long running stress test on a custom board shipping an AXG SoCs and a Realtek RTL8211F PHY revealed that after a few hours the connection speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time the 'macirq' (eth0) IRQ would stop being triggered at all and as consequence the GMAC IRQs never ACKed. After a painful investigation the problem seemed to be due to a wrong defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of EDGE_RISING. The change in the macirq IRQ type also solved another long standing issue affecting this SoC/PHY where EEE was causing the network connection to die after stressing it with iperf3 (even though much sooner). It's now possible to remove the 'eee-broken-1000t' quirk as well. Fixes: 9c15795a4f96 ("ARM: dts: meson8b-odroidc1: ethernet support") Signed-off-by: Carlo Caione <ccaione@baylibre.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-26ARM: dts: meson8b: odroidc1: add stdout-path propertyMartin Blumenstingl1-0/+4
To use the "earlycon" kernel command line parameter (without arguments) we need a stdout-path property under the /chosen node. Add this to make it easier to spot errors early in the boot process when looking for them. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-26ARM: dts: meson8b: odroidc1: enable the SAR ADCMartin Blumenstingl1-0/+5
Odroid-C1 exposes ADC channels 0 and 1 on the GPIO headers. NOTE: Due to the SoC design these are limited to 1.8V (instead of 3.3V like all other pins). Enable the SAR ADC to enable voltage measurements on these pins. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-26ARM: dts: meson8b: odroidc1: add the fixed voltage regulatorsMartin Blumenstingl1-0/+73
There are multiple fixed regulators on the Odroid-C1 board. Add them so they can be used when we add the devices that need them (SAR ADC needs the 1.8V IOREF, RTC needs VDD_RTC). These are: - P5V0 is the main 5V power input - VCC3V3 / VDDIO_AO3V3 / VDD3V3: fixed regulator with 3.3V output which is supplied by P5V0 - IOREF_1V8 / VCC1V8 / VDD1V8: fixed regulator with 1.8V output which is supplied by P5V0 - VDD_RTC: fixed voltage regulator with 0.9V output which is supplied by VDDIO_AO3V3 - DDR_VDDC / DDR3_1V5: fixed voltage regulator with 1.5V output which is supplied by P5V0 - the existing TF_IO and RFLASH_VDD_EN regulators are supplied by VDDIO_AO3V3 - the existing VCCK regulator is supplied by P5V0 This does not add the missing VDDEE regulator (controlled by PWM_D) because it's not clear yet how to configure the voltage of that regulator. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-26ARM: dts: meson8b: odroidc1: add the CPU voltage regulatorMartin Blumenstingl1-0/+27
The CPU voltage regulator is a "Monolithic Power Systems MP2161" (according to the Odroid-C1+'s schematics). It is driven by PWM_C on GPIODV_9. Hardkernel's 3.10 kernel (based on the Amlogic GPL kernel sources) defines a PWM voltage table with the following values: - 0.86 volts = PWM register value 0x10f001b - (more values in 0.1 volt increments) - 1.14 volts = PWM register value 0x000012a When using the XTAL (24MHz) as input this translates into a PWM period of 12218ns with 0.86V using a duty cycle of 91% and 1.14V using a duty cycle of 0%. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-05-10ARM: dts: meson8b: odroid-c1: enable the IR receiverMartin Blumenstingl1-0/+6
The Odroid-C1 comes with an IR receiver. It is connected to the GPIOAO_7 pin and thus using the SoC's internal IR decoder. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-05-10ARM: dts: meson8b: odroid-c1: sort nodes alphabeticallyMartin Blumenstingl1-34/+34
This makes it easier to find existing nodes. No functional changes. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-03-21ARM: dts: meson8b-odroidc1: add microSD supportLinus Lüssing1-0/+58
The Odroid C1 features a microSD slot. This patch adds the necessary DT bindings to support it. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-02-13ARM: dts: meson8b-odroidc1: ethernet supportEmiliano Ingrassia1-0/+30
The Odroid-C1+ board is equipped with an RTL8211F ethernet PHY which supports 10/100/1000 Mbps ethernet. The PHY reset and interrupt lines are controlled by the SoC via two GPIO lines (GPIOH_4 and GPIOH_3 respectively). The PHY energy efficient ethernet (eee) mode is marked as broken using "eee-broken-1000t" because, during tests, high packet losses were experienced without it. Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Tested-by: Linus Lüssing <linus.luessing@c0d3.blue> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-10-07ARM: dts: meson: enabling the USB Host controller on Odroid-C1/C1+ boardEmiliano Ingrassia1-0/+23
This patch enables the USB Host controller (USB1) and the relative USB2 PHY on Odroid-C1/C1+ board. Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2016-01-04ARM: meson: Add status LED for Odroid-C1Edward Cragg1-0/+11
Add the blue status LED to the Hardkernel Odroid C1 board DTS. Signed-off-by: <edward.cragg@codethink.co.uk> Signed-off-by: Carlo Caione <carlo@endlessm.com>
2015-10-08ARM: meson: Add DTS for Odroid-C1 and Tronfy MXQ boardsCarlo Caione1-0/+67
Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
generated by cgit v1.2.3 (git 2.39.0) at 2025-01-04 13:22:10 +0300