| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All 4 SPI controllers on NXP LPC32xx SoC support SPI slaves discerning them
by one cell address value, set it as default to avoid duplication in board
device tree files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
NXP LPC3220 and LPC3230 SoCs do NOT contain a MAC controller, so,
since for now there is just one dtsi file for all variants of
NXP LPC32xx SoCs, it is reasonable to disable the controller
by default and enable it in device tree files of particular boards.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change adds a unit address to memory device node, the issue was
reported as a unit_address_vs_reg warning by dtc.
Root device node properties #address-cells and #size-cells were
removed as inherited from lpc32xx.dtsi.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The change adds description of Sharp LQ035Q7DB03 3.5" 320x240 TFT panel,
which is connected to Phytec phyCORE-LPC3250 board, ARM PrimeCell PL111
LCD controller on NXP LPC3250 SoC gets its configuration appropriately
to support graphics output to the panel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The originally added 'regulators' device node has a number of flaws,
to name a few its children has unit addresses but no reg properties,
the regulators are not captured by a device driver due to a missing
'simple-bus' compatible, the regulator names are selected by killing
either alphabetical order or device node grouping property.
The change removes 'regulators' device node and renames the regulators
and labels.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
The fixed voltage regulator on Phytec phyCORE-LPC3250 board, which
supplies SD/MMC card's power, has a constant output voltage level
of either 3.15V or 3.3V, the actual value depends on JP4 position,
the power rail is referenced as VCC_SDIO in the board hardware manual.
Fixes: d06670e96267 ("arm: dts: phy3250: add SD fixed regulator")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/questions/59497/alsa-asoc-how-to-correctly-load-devices-drivers/62217#62217
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to PHYTEC PHYCORE-LPC3250 board dts
file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
