| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Generally, power LEDs should indicate when power is applied, and go out
once power is removed. _Not_ annoy the developer with migraine-inducing
blinking reminicent of some badly animated television series designed to
sell sugar to children.
On a more serious note, most of these OS-specific properties aren't
necessary and should be removed. I left two that are legitimately tying
disk LEDs to disk activity. Other than that, we keep the state the
bootloader left them in until userspace changes the state via sysfs.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
A lot of device setup is shared between DNS-320 and DNS-325, move the
definitions into a common include.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Replace code in board-dnskw with the equivalent devicetree bindings.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Now that we have I2C support in DT, describe the LM75 in
the DT file for the DNS325.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
|
|
Convert boards using DT, but the old way of configuring SATA to now
use properties in there DT file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
|
|
It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Use devicetree to define NAND partitions. Use D-link partition scheme by
default, to be vaguely compatible with their userland.
Changes since last submission (V4):-
* Don't add NAND support then throw it away immediately after [Grant Likely]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Add support for the DNS-320 and DNS-325. Describe as much as currently possible
in the devicetree files, create a board-dnskw.c for everything else.
Changes since last submission (V3) [Addressing comments by]:-
* One MACH_DLINK_KIRKWOOD_DT for all dtb files [Grant Likely, Jason Cooper]
* Drop brain-dead select "select CONFIG_MTD_OF_PARTS" [Grant Likely]
* Don't add NAND support then throw it away immediately after [Grant Likely]
* Describe purpose of MPP 41, 42 & 49
Changes since last submission (V2):-
* Use IEEE-compliant "okay", rather than "ok" [Scott Wood]
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
