summaryrefslogtreecommitdiff
path: root/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
AgeCommit message (Collapse)AuthorFilesLines
2017-03-08ARM: dts: imx6sx-udoo-neo: Fix reboot hangFabio Estevam1-5/+0
After issuing a 'reboot' command the imx6sx-udoo-neo board does not reboot as expected and it just hangs instead. In mainline kernel only LDO enabled mode is supported. Do not provide arm-supply/soc-supply nodes in the device tree, so that the board operates in LDO enabled mode and can then successfully reboot via watchdog. Fixes: 76e691fc7653b85d39 ("ARM: dts: imx6sx: Add UDOO Neo support") Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-01-29ARM: dts: udoo_neo: Add Bluetooth supportBreno Lima1-0/+32
Udoo Neo has a TI WL1831 Bluetooth chip connected to the UART3 port. Add support for it. Signed-off-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-01-29ARM: dts: udoo_neo: Add Wifi supportBreno Lima1-0/+45
Udoo Neo has a TI WL1831 Wifi chip connected to the USDHC3 port. Add support for it. Signed-off-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-01-29ARM: dts: udoo_neo: Add UDOO Neo USB OTG1 and OTG2 supportBreno Lima1-0/+59
Add support for micro USB (OTG1) and USB Host (OTG2) for UDOO Neo board. Tested on a UDOO Neo Full board by mounting a mass storage device on both ports. Signed-off-by: Breno Lima <breno.lima@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2017-01-02ARM: dts: imx6sx-udoo-neo: Pass the 'phy-reset-duration' propertyFabio Estevam1-0/+1
imx6sx-udoo-neo has a KSZ8091 Ethernet PHY, which requires the reset signal to be low for at least 10ms. Pass the 'phy-reset-duration' property to reflect such requirement. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2016-10-24ARM: dts: imx6sx: Add UDOO Neo supportAndreas Färber1-0/+293
Add initial device trees for UDOO Neo Basic, Extended and Full boards: * Serial console is enabled, other serial ports are prepared. * I2C based PMIC is enabled. * Ethernet is enabled for Basic and Full. * SDHC is enabled, with the SDIO_PWR GPIO modeled as a regulator. * Both user LEDs are enabled, with the orange one reserved for the M4 and with the SD card as default trigger for the red LED. The decision on a board compatible string is deferred to later. Cc: Ettore Chimenti <ettore.chimenti@udoo.org> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>