| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing pinmux entry for OSC32K_32K_OUT on pad ENET_RXD0 used by the
Variscite DART-MX6 SoM.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
From "Chip Errata for the i.MX 6Dual/6Quad"
ERR006687 ENET: Only the ENET wake-up interrupt request can wake the
system from Wait mode.
The ENET block generates many interrupts. Only one of these interrupt lines
is connected to the General Power Controller (GPC) block, but a logical OR
of all of the ENET interrupts is connected to the General Interrupt Controller
(GIC). When the system enters Wait mode, a normal RX Done or TX Done does not
wake up the system because the GPC cannot see this interrupt. This impacts
performance of the ENET block because its interrupts are serviced only when
the chip exits Wait mode due to an interrupt from some other wake-up source.
Adding MX6QDL_PAD_GPIO_6__ENET_IRQ is the 1st step to
workaround this problem.
The input reg is set to 0x3c to set IOMUX_OBSRV_MUX1 to ENET_IRQ.
The mux reg value is 0x11, so that the observable mux is routed to
this pin and to the gpio controller(sion bit). These magic values
come from Ranjani Vaidyanathan's patch:
"ENGR00257847-1 MX6Q/DL-Fix Ethernet performance issue when WAIT mode is active"
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The solo/duallite reference manual does not mention
this setting, but it works.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).
As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.
31 23 15 7 0
| 0xff | shift | width | select |
Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The patch "0b7a76a ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The uart2 in the imx6q-arm2 board is used as a DTE uart,
this patch adds the necessary DTE pads for uart2.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Currently, all imx pinctrl drivers maintain a big array of struct
imx_pin_reg which hard-codes data like register offset and mux mode
setting for each pin function. Every time a new imx SoC support is
added, we need to add such a big mount of data. With moving to single
kernel build, it's only matter of time to be blamed on memory consuming.
With DTC pre-processor support in place, the patch moves all these data
into device tree by redefining the PIN_FUNC_ID in imxXX-pinfunc.h and
changing the PIN_FUNC_ID parsing code a little bit.
The pin id gets re-numbered based on mux register offset, or config
register offset if the pin has no mux register, so that kernel can
identify the pin id from register offsets provided by device tree.
As a bonus point of the change, those arbitrary magic numbers standing
for particular PIN_FUNC_ID in device tree sources are now replaced by
macros to improve the readability of dts files.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
