| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Value taken from Galaxy S2 Epic 4G Touch SPH-D710 Android vendor
kernel [0] which always sets 200mA.
Also rearrange regulators based on definition in max8997.h.
[0] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/power/sec_battery_u1.c#L1525
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Link: https://lore.kernel.org/r/20201230205139.1812366-8-timon.baetz@protonmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Set CHARGER current and CHARGER_CV voltage according to Galaxy S2 Epic
4G Touch SPH-D710 Android vendor sources [0,1].
Remove regulator-always-on. The regulator can be enabled and disabled
based on extcon events.
[0] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/power/max8997_charger_u1.c#L169-L170
[1] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/power/max8997_charger_u1.c#L390-L391
Signed-off-by: Timon Baetz <timon.baetz@protonmail.com>
Link: https://lore.kernel.org/r/20201230205139.1812366-7-timon.baetz@protonmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-3-krzk@kernel.org
|
|
Align the name of mag-mhl-gpio node to avoid dtschema confusion and
dtbs_check warning:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: pinctrl@11000000: mag-mhl-gpio:
{'samsung,pins': ['gpd0-2'], 'samsung,pin-function': [[3]], 'samsung,pin-pud': [[0]]} is not of type 'array'
From schema: dtschema/schemas/gpio/gpio-consumer.yaml
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-22-krzk@kernel.org
|
|
Using full paths to extend or override a device tree node is error prone
since if there was a typo error, a new node will be created instead of
extending the node as it was desired. This will lead to run-time errors
that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error
(during build time).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-17-krzk@kernel.org
|
|
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: spi-lcd:
$nodename:0: 'spi-lcd' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-15-krzk@kernel.org
|
|
The PMIC has a 32768 Hz clock used by the modem which is implemented by
driver as a regulator. Add and enable it to be sure modem get's its
signal.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-8-krzk@kernel.org
|
|
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC
(Maxim MAX8997). However there is no clock provided for the PMIC and
the driver registers the clock as regulator. This is an old driver
which will not be updated so add a workaround:
1. Enable the "clock" regulator in PMIC,
2. Add a fixed-clock to fill missing clock phandle reference in S3C RTC.
This allows to enable the S3C RTC and fixes dtbs_check warnings:
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: rtc@10070000: clocks: [[5, 346]] is too short
arch/arm/boot/dts/exynos4210-i9100.dt.yaml: rtc@10070000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-3-krzk@kernel.org
|
|
The regulator property 'regulator-microvolt-offset' should be put next
to regulator definition, not consumer.
The property 'regulator-microsecs-delay' is not valid at all.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-2-krzk@kernel.org
|
|
The name of I2C controller over GPIO lines node ends with '-gpio' which
confuses dtschema:
/arch/arm/boot/dts/exynos4210-i9100.dt.yaml: /: i2c-gpio:
{'compatible': ['i2c-gpio'], ... 'maxim,over-volt': [[4500]]}} is not of type 'array'
From schema: lib/python3.6/site-packages/dtschema/schemas/gpio/gpio-consumer.yaml
Add a '-0' suffix to silence it. This pattern on naming i2c-gpio is
already present in many other dts. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200830135200.24304-1-krzk@kernel.org
|
|
The updated "i2c-gpio" driver bindings require to define the SDA and SCL
GPIO lines in the separate properties and mark both as GPIO_OPEN_DRAIN.
Covert all Exynos dts files to follow this style.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add devicetree file for the Exynos4210 based Galaxy S2 (GT-I9100
version).
Signed-off-by: Stenkin Evgeniy <stenkinevgeniy@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
