| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On the GP EVM, the ambient light sensor is limited to 100KHz on the
I2C bus.
So use 100kHz for I2C on the GP EVM due to this limitation on the
ambient light sensor.
Reported-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
|
|
Update the bindings for touchscreen size.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix i2c nodes indentation.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP DT fbdev updates from Tomi Valkeinen:
"Here are display related device tree data changes for OMAP. They are
based on an already merged branch to satisfy the dependencies for the
dts file changes.
Add OMAP DT data:
- omap5 display subsystem
- display data for omap5 uEVM board
- am43xx display subsystem
- display data for am43xx ePOS and GP boards (LCD only)
- display data for GTA04 board
- display data for overo board
- display data for duovero-parlor board
- display data for omap3 evm and ldp boards"
* tag 'fbdev-omap-dt-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: omap5.dtsi: Add audio related parameters to hdmi node
ARM: omap4.dtsi: Add audio related parametes to hdmi node
ARM: dts: duovero-parlor: Add HDMI output
ARM: dts: overo: Add support for 3.5'' LCD output
ARM: dts: overo: Add support for 4.3'' LCD output
ARM: dts: overo: Add support for DVI output
ARM: dts: Add LCD panel sharp ls037v7dw01 support for omap3-evm and ldp
ARM: dts: omap3-gta04: Add display support
ARM: dts: omap5-uevm.dts: add display nodes
ARM: dts: omap5-uevm.dts: add tca6424a
ARM: dts: omap5.dtsi: add DSS nodes
ARM: dts: am43x-epos-evm: add LCD data
ARM: dts: am437x-gp-evm: add LCD data
ARM: dts: am4372.dtsi: add DSS information
|
|
Add DT data for am437x-gp-evm's LCD panel.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
|
|
Adds pinmux and DT node for Micron (MT29F4G08AB) x8 NAND device present on
am437x-gp-evm board.
(1) As NAND Flash data lines are muxed with eMMC, Thus at a given time either
eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled:
(a) By dynamically driving following GPIO pin from software
SPI2_CS0(GPIO) == 0 NAND is selected (default)
SPI2_CS0(GPIO) == 1 eMMC is selected
(b) By statically using Jumper (J89) on the board
(2) As NAND device connnected to this board has page-size=4K and oob-size=224,
So ROM code expects boot-loaders to be flashed in BCH16 ECC scheme for
NAND boot.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add CPSW ethernet support for AM437x GP EVM which has one slave pinned out
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The VTT regulator for DDR3 termination on the am437x-gp-evm is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add touchscreen support for AM437x GP EVM using pixcir
touchscreen controller.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable
- USB PHY
- USB
for am437x-gp-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Do not reset GPIO5 at boot-up because GPIO5_7 is used
on AM437x GP-EVM to control VTT regulators on DDR3.
Without this some GP-EVM boards will fail to boot because
of DDR3 corruption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
enable sd card slot on am437x-gp-evm
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add gpio keys node for am43x gp evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
Add pwm backlight support for gp evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
|
AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
|
