| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In order to use the same set of routines to register notifiers for
different request types, update the existing
dev_pm_qos_{add|remove}_notifier() routines with an additional
parameter: request-type.
For now, it only supports resume-latency request type but will be
extended to frequency limit (min/max) constraints later on.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For thermal management strategy you might be interested on limit the
input power for a power supply. We already have current limit but
basically what we probably want is to limit power. So, introduce the
input_power_limit property.
Although the common use case is limit the input power, in some
specific cases it is the voltage that is problematic (i.e some regulators
have different efficiencies at higher voltage resulting in more heat).
So introduce also the input_voltage_limit property.
This happens in one Chromebook and is used on the Pixel C's thermal
management strategy to effectively limit the input power to 5V 3A when
the screen is on. When the screen is on, the display, the CPU, and the GPU
all contribute more heat to the system than while the screen is off, and
we made a tradeoff to throttle the charger in order to give more of the
thermal budget to those other components.
So there's nothing fundamentally broken about the hardware that would
cause the Pixel C to malfunction if we were charging at 9V or 12V instead
of 5V when the screen is on, i.e. if userspace doesn't change this.
What would happen is that you wouldn't meet Google's skin temperature
targets on the system if the charger was allowed to run at 9V or 12V with
the screen on.
For folks hacking on Pixel Cs (which is now outside of Google's official
support window for Android) and customizing their own kernel and userspace
this would be acceptable, but we wanted to expose this feature in the
power supply properties because the feature does exist in the Emedded
Controller firmware of the Pixel C and all of Google's Chromebooks with
USB-C made since 2015 in case someone running an up to date kernel wanted
to limit the charging power for thermal or other reasons.
This patch exposes a new property, similar to input current limit, to
re-configure the maximum voltage from the external supply at runtime
based on system-level knowledge or user input.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Convert the PM documents to ReST, in order to allow them to
build with Sphinx.
The conversion is actually:
- add blank lines and indentation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
|
|
Introduce a documentation file summarizing the key design points and
APIs of the newly introduced Energy Model framework.
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: corbet@lwn.net
Cc: dietmar.eggemann@arm.com
Cc: morten.rasmussen@arm.com
Cc: patrick.bellasi@arm.com
Cc: qais.yousef@arm.com
Cc: rjw@rjwysocki.net
Link: https://lkml.kernel.org/r/20190110110546.8101-2-quentin.perret@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Whilst making an unrelated change to some Documentation, Linus sayeth:
| Afaik, even in Britain, "whilst" is unusual and considered more
| formal, and "while" is the common word.
|
| [...]
|
| Can we just admit that we work with computers, and we don't need to
| use þe eald Englisc spelling of words that most of the world never
| uses?
dictionary.com refers to the word as "Chiefly British", which is
probably an undesirable attribute for technical documentation.
Replace all occurrences under Documentation/ with "while".
Cc: David Howells <dhowells@redhat.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michael Halcrow <mhalcrow@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Pull documentation updates from Jonathan Corbet:
"This is a fairly typical cycle for documentation. There's some welcome
readability improvements for the formatted output, some LICENSES
updates including the addition of the ISC license, the removal of the
unloved and unmaintained 00-INDEX files, the deprecated APIs document
from Kees, more MM docs from Mike Rapoport, and the usual pile of typo
fixes and corrections"
* tag 'docs-4.20' of git://git.lwn.net/linux: (41 commits)
docs: Fix typos in histogram.rst
docs: Introduce deprecated APIs list
kernel-doc: fix declaration type determination
doc: fix a typo in adding-syscalls.rst
docs/admin-guide: memory-hotplug: remove table of contents
doc: printk-formats: Remove bogus kobject references for device nodes
Documentation: preempt-locking: Use better example
dm flakey: Document "error_writes" feature
docs/completion.txt: Fix a couple of punctuation nits
LICENSES: Add ISC license text
LICENSES: Add note to CDDL-1.0 license that it should not be used
docs/core-api: memory-hotplug: add some details about locking internals
docs/core-api: rename memory-hotplug-notifier to memory-hotplug
docs: improve readability for people with poorer eyesight
yama: clarify ptrace_scope=2 in Yama documentation
docs/vm: split memory hotplug notifier description to Documentation/core-api
docs: move memory hotplug description into admin-guide/mm
doc: Fix acronym "FEKEK" in ecryptfs
docs: fix some broken documentation references
iommu: Fix passthrough option documentation
...
|
|
This commit updates the default value of /sys/power/image_size in
the documentation.
Since ac5c24ec1e983313ef0015258fba6f630e54e7cn the `image_size' value is
set to about 2/5 of RAM, according to kernel/power/snapshot.c:
image_size = ((totalram_pages * 2) / 5) * PAGE_SIZE;
but this change was not reflected everywhere in the documentation.
Signed-off-by: Vladimir D. Seleznev <vseleznv@altlinux.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This is a respin with a wider audience (all that get_maintainer returned)
and I know this spams a *lot* of people. Not sure what would be the correct
way, so my apologies for ruining your inbox.
The 00-INDEX files are supposed to give a summary of all files present
in a directory, but these files are horribly out of date and their
usefulness is brought into question. Often a simple "ls" would reveal
the same information as the filenames are generally quite descriptive as
a short introduction to what the file covers (it should not surprise
anyone what Documentation/sched/sched-design-CFS.txt covers)
A few years back it was mentioned that these files were no longer really
needed, and they have since then grown further out of date, so perhaps
it is time to just throw them out.
A short status yields the following _outdated_ 00-INDEX files, first
counter is files listed in 00-INDEX but missing in the directory, last
is files present but not listed in 00-INDEX.
List of outdated 00-INDEX:
Documentation: (4/10)
Documentation/sysctl: (0/1)
Documentation/timers: (1/0)
Documentation/blockdev: (3/1)
Documentation/w1/slaves: (0/1)
Documentation/locking: (0/1)
Documentation/devicetree: (0/5)
Documentation/power: (1/1)
Documentation/powerpc: (0/5)
Documentation/arm: (1/0)
Documentation/x86: (0/9)
Documentation/x86/x86_64: (1/1)
Documentation/scsi: (4/4)
Documentation/filesystems: (2/9)
Documentation/filesystems/nfs: (0/2)
Documentation/cgroup-v1: (0/2)
Documentation/kbuild: (0/4)
Documentation/spi: (1/0)
Documentation/virtual/kvm: (1/0)
Documentation/scheduler: (0/2)
Documentation/fb: (0/1)
Documentation/block: (0/1)
Documentation/networking: (6/37)
Documentation/vm: (1/3)
Then there are 364 subdirectories in Documentation/ with several files that
are missing 00-INDEX alltogether (and another 120 with a single file and no
00-INDEX).
I don't really have an opinion to whether or not we /should/ have 00-INDEX,
but the above 00-INDEX should either be removed or be kept up to date. If
we should keep the files, I can try to keep them updated, but I rather not
if we just want to delete them anyway.
As a starting point, remove all index-files and references to 00-INDEX and
see where the discussion is going.
Signed-off-by: Henrik Austad <henrik@austad.us>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Just-do-it-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: [Almost everybody else]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
At present, "systemctl suspend" and "shutdown" can run in parrallel. A
system can suspend after devices_shutdown(), and resume. Then the shutdown
task goes on to power off. This causes many devices are not really shut
off. Hence replacing reboot_mutex with system_transition_mutex (renamed
from pm_mutex) to achieve the exclusion. The renaming of pm_mutex as
system_transition_mutex can be better to reflect the purpose of the mutex.
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
firmware_class.c was split into several files under
drivers/base/firmware_loader. The new main.c has the functions which
/request_firmware.rst references.
Acked-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the only way to specify a hibernate offset for a
swap file is on the kernel command line.
Add a new /sys/power/resume_offset that lets userspace
specify the offset and disk to use when initiating a hibernate
cycle.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This is a quiet release in terms of code volume but a fairly big one
in terms of framework changes - we've got one long awaited feature in
the form of runtime configuration of suspend and the start of coupled
regulator support too:
- Support for modifying the voltage and enable configuration devices
will have in suspend, contributed by Chunyan Zhang.
- Support for the Spreadtrum SC2731, contributed by Erick Chen.
- The start of changes to support coupled regulators from Maciej
Purski, the rest of the series should arrive for v4.17"
* tag 'regulator-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix build error
regulator: core: Refactor regulator_list_voltage()
regulator: core: Move of_find_regulator_by_node() to of_regulator.c
regulator: add PM suspend and resume hooks
regulator: empty the old suspend functions
regulator: leave one item to record whether regulator is enabled
regulator: make regulator voltage be an array to support more states
regulator: added support for suspend states
regulator: qcom_spmi: Use regmap helpers for enable/disable/is_enabled callback
regulator: sc2731: Fix defines for SC2731_WR_UNLOCK and SC2731_PWR_WR_PROT_VALUE
regulator: fix incorrect indentation of two assignment statements
regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC
regulator: Add Spreadtrum SC2731 regulator documentation
regulator: Update code examples in documentation
MAINTAINERS: regulator: Add Documentation/power/regulator/
regulator: tps65218: Add NULL test for devm_kzalloc call
regulator: tps65218: Remove unused enum tps65218_regulators
|
|
This involves using the REGULATOR_SUPPLY initializer macro and
reindenting some of the code.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for DPM_FLAG_LEAVE_SUSPENDED to the PCI bus type by
making it (a) set the power.may_skip_resume status bit for devices
that, from its perspective, may be left in suspend after system
wakeup from sleep and (b) return early from pci_pm_resume_noirq()
for devices whose remaining resume callbacks during the transition
under way are going to be skipped by the PM core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The check for "active" children in __pm_runtime_set_status(), when
trying to set the parent device status to "suspended", doesn't
really make sense, because in fact it is not invalid to set the
status of a device with runtime PM disabled to "suspended" in any
case. It is invalid to enable runtime PM for a device with its
status set to "suspended" while its child_count reference counter
is nonzero, but the check in __pm_runtime_set_status() doesn't
really cover that situation.
For this reason, drop the children check from __pm_runtime_set_status()
and add a check against child_count reference counters of "suspended"
devices to pm_runtime_enable().
Fixes: a8636c89648a (PM / Runtime: Don't allow to suspend a device with an active child)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"There are no real big ticket items here this time.
The most noticeable change is probably the relocation of the OPP
(Operating Performance Points) framework to its own directory under
drivers/ as it has grown big enough for that. Also Viresh is now going
to maintain it and send pull requests for it to me, so you will see
this change in the git history going forward (but still not right
now).
Another noticeable set of changes is the modifications of the PM core,
the PCI subsystem and the ACPI PM domain to allow of more integration
between system-wide suspend/resume and runtime PM. For now it's just a
way to avoid resuming devices from runtime suspend unnecessarily
during system suspend (if the driver sets a flag to indicate its
readiness for that) and in the works is an analogous mechanism to
allow devices to stay suspended after system resume.
In addition to that, we have some changes related to supporting
frequency-invariant CPU utilization metrics in the scheduler and in
the schedutil cpufreq governor on ARM and changes to add support for
device performance states to the generic power domains (genpd)
framework.
The rest is mostly fixes and cleanups of various sorts.
Specifics:
- Relocate the OPP (Operating Performance Points) framework to its
own directory under drivers/ and add support for power domain
performance states to it (Viresh Kumar).
- Modify the PM core, the PCI bus type and the ACPI PM domain to
support power management driver flags allowing device drivers to
specify their capabilities and preferences regarding the handling
of devices with enabled runtime PM during system suspend/resume and
clean up that code somewhat (Rafael Wysocki, Ulf Hansson).
- Add frequency-invariant accounting support to the task scheduler on
ARM and ARM64 (Dietmar Eggemann).
- Fix PM QoS device resume latency framework to prevent "no
restriction" requests from overriding requests with specific
requirements and drop the confusing PM_QOS_FLAG_REMOTE_WAKEUP
device PM QoS flag (Rafael Wysocki).
- Drop legacy class suspend/resume operations from the PM core and
drop legacy bus type suspend and resume callbacks from ARM/locomo
(Rafael Wysocki).
- Add min/max frequency support to devfreq and clean it up somewhat
(Chanwoo Choi).
- Rework wakeup support in the generic power domains (genpd)
framework and update some of its users accordingly (Geert
Uytterhoeven).
- Convert timers in the PM core to use timer_setup() (Kees Cook).
- Add support for exposing the SLP_S0 (Low Power S0 Idle) residency
counter based on the LPIT ACPI table on Intel platforms (Srinivas
Pandruvada).
- Add per-CPU PM QoS resume latency support to the ladder cpuidle
governor (Ramesh Thomas).
- Fix a deadlock between the wakeup notify handler and the notifier
removal in the ACPI core (Ville Syrjälä).
- Fix a cpufreq schedutil governor issue causing it to use stale
cached frequency values sometimes (Viresh Kumar).
- Fix an issue in the system suspend core support code causing wakeup
events detection to fail in some cases (Rajat Jain).
- Fix the generic power domains (genpd) framework to prevent the PM
core from using the direct-complete optimization with it as that is
guaranteed to fail (Ulf Hansson).
- Fix a minor issue in the cpuidle core and clean it up a bit (Gaurav
Jindal, Nicholas Piggin).
- Fix and clean up the intel_idle and ARM cpuidle drivers (Jason
Baron, Len Brown, Leo Yan).
- Fix a couple of minor issues in the OPP framework and clean it up
(Arvind Yadav, Fabio Estevam, Sudeep Holla, Tobias Jordan).
- Fix and clean up some cpufreq drivers and fix a minor issue in the
cpufreq statistics code (Arvind Yadav, Bhumika Goyal, Fabio
Estevam, Gautham Shenoy, Gustavo Silva, Marek Szyprowski, Masahiro
Yamada, Robert Jarzmik, Zumeng Chen).
- Fix minor issues in the system suspend and hibernation core, in
power management documentation and in the AVS (Adaptive Voltage
Scaling) framework (Helge Deller, Himanshu Jha, Joe Perches, Rafael
Wysocki).
- Fix some issues in the cpupower utility and document that Shuah
Khan is going to maintain it going forward (Prarit Bhargava, Shuah
Khan)"
* tag 'pm-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (88 commits)
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
intel_idle: Graceful probe failure when MWAIT is disabled
cpufreq: schedutil: Reset cached_raw_freq when not in sync with next_freq
freezer: Fix typo in freezable_schedule_timeout() comment
PM / s2idle: Clear the events_check_enabled flag
cpufreq: stats: Handle the case when trans_table goes beyond PAGE_SIZE
cpufreq: arm_big_little: make cpufreq_arm_bL_ops structures const
cpufreq: arm_big_little: make function arguments and structure pointer const
cpuidle: Avoid assignment in if () argument
cpuidle: Clean up cpuidle_enable_device() error handling a bit
ACPI / PM: Fix acpi_pm_notifier_lock vs flush_workqueue() deadlock
PM / Domains: Fix genpd to deal with drivers returning 1 from ->prepare()
cpuidle: ladder: Add per CPU PM QoS resume latency support
PM / QoS: Fix device resume latency framework
PM / domains: Rework governor code to be more consistent
PM / Domains: Remove gpd_dev_ops.active_wakeup() callback
soc: rockchip: power-domain: Use GENPD_FLAG_ACTIVE_WAKEUP
soc: mediatek: Use GENPD_FLAG_ACTIVE_WAKEUP
ARM: shmobile: pm-rmobile: Use GENPD_FLAG_ACTIVE_WAKEUP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp/hotplug updates from Thomas Gleixner:
"No functional changes, just removal of obsolete and outdated defines,
macros and documentation"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
cpu/hotplug: Get rid of CPU hotplug notifier leftovers
cpu/hotplug: Remove obsolete notifier macros
|
|
The CPU hotplug notifiers are history. Remove the last reminders.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Make the PCI bus type take DPM_FLAG_SMART_SUSPEND into account in its
system-wide PM callbacks and make sure that all code that should not
run in parallel with pci_pm_runtime_resume() is executed in the "late"
phases of system suspend, freeze and poweroff transitions.
[Note that the pm_runtime_suspended() check in pci_dev_keep_suspended()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add checks
for that in pci_pm_suspend_late/noirq(), pci_pm_freeze_late/noirq()
and pci_pm_poweroff_late/noirq().
Moreover, if pci_pm_resume_noirq() or pci_pm_restore_noirq() is
called during the subsequent system-wide resume transition and if
the device was left in runtime suspend previously, its runtime PM
status needs to be changed to "active" as it is going to be put
into the full-power state, so add checks for that too to these
functions.
In turn, if pci_pm_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
In addition to the above add a core helper for checking if
DPM_FLAG_SMART_SUSPEND is set and the device runtime PM status is
"suspended" at the same time, which is done quite often in the new
code (and will be done elsewhere going forward too).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The motivation for this change is to provide a way to work around
a problem with the direct-complete mechanism used for avoiding
system suspend/resume handling for devices in runtime suspend.
The problem is that some middle layer code (the PCI bus type and
the ACPI PM domain in particular) returns positive values from its
system suspend ->prepare callbacks regardless of whether the driver's
->prepare returns a positive value or 0, which effectively prevents
drivers from being able to control the direct-complete feature.
Some drivers need that control, however, and the PCI bus type has
grown its own flag to deal with this issue, but since it is not
limited to PCI, it is better to address it by adding driver flags at
the core level.
To that end, add a driver_flags field to struct dev_pm_info for flags
that can be set by device drivers at the probe time to inform the PM
core and/or bus types, PM domains and so on on the capabilities and/or
preferences of device drivers. Also add two static inline helpers
for setting that field and testing it against a given set of flags
and make the driver core clear it automatically on driver remove
and probe failures.
Define and document two PM driver flags related to the direct-
complete feature: NEVER_SKIP and SMART_PREPARE that can be used,
respectively, to indicate to the PM core that the direct-complete
mechanism should never be used for the device and to inform the
middle layer code (bus types, PM domains etc) that it can only
request the PM core to use the direct-complete mechanism for
the device (by returning a positive value from its ->prepare
callback) if it also has been requested by the driver.
While at it, make the core check pm_runtime_suspended() when
setting power.direct_complete so that it doesn't need to be
checked by ->prepare callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The PM QoS flag PM_QOS_FLAG_REMOTE_WAKEUP is not used consistently
and the vast majority of code simply assumes that remote wakeup
should be enabled for devices in runtime suspend if they can
generate wakeup signals, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Make admin-guide document refs valid.
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Make driver-api document refs valid.
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The Documentation/power/states.txt document is now redundant and
sonewhat outdated, so delete it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Modify the ACPI system sleep support setup code to select
suspend-to-idle as the default system sleep state if
(1) the ACPI_FADT_LOW_POWER_S0 flag is set in the FADT and
(2) the Low Power Idle S0 _DSM interface has been discovered and
(3) the default sleep state was not selected from the kernel command
line.
The main motivation for this change is that systems where the (1) and
(2) conditions are met typically ship with OSes that don't exercise
the S3 path in the platform firmware which remains untested and turns
out to be non-functional at least in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
|
|
Since commit a8636c89648a (PM / Runtime: Don't allow to suspend a
device with an active child) it is no longer permitted to set
RPM_SUSPENDED state for a device with active children unless
power.ignore_children is set.
Update the documentation to reflect this.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"New drivers:
- Linear ltc3651 charger driver
- Motorola CPCAP battery fuel-gauge driver
New chip/feature support:
- bq27xxx: prepare for chip data setup
- axp20x_battery: support max charge current setup
New core features:
- add Apple Brick ID type
- support "supplied-from" device property for generic ACPI/pdata support
- support strings for sysfs properties representing enums
- introduce battery-info (backend is DT only for now)
- provide reboot-mode header globally
.. and misc fixes"
* tag 'for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (39 commits)
power: supply: sbs-battery: Don't needlessly set CAPACITY_MODE
power: supply: sbs-battery: Prevent CAPACITY_MODE races
power: supply: bq24735: remove incorrect le16_to_cpu calls
power: supply: sbs-battery: remove incorrect le16_to_cpu calls
power: supply: cpcap-charger: Add missing power_supply_config
power: supply: twl4030-charger: move allocation of iio channel to the beginning
power: supply: twl4030-charger: allocate iio by devm_iio_channel_get() and fix error path
power: supply: core: constify psy_tcd_ops.
dt-bindings: power: supply: cpcap-battery: Add power-supplies property
dt-bindings: power: supply: move max8903-charger.txt to proper location
dt-bindings: power: supply: move maxim,max14656.txt to proper location
power: supply: twl4030_charger: Use sysfs_match_string() helper
power: reset: reboot-mode: Make include file global
power: supply: axp20x_battery: add DT support for battery max constant charge current
power: supply: axp20x_battery: add support for DT battery
power: supply: bq27xxx: Add power_supply_battery_info support
power: supply: bq27xxx: Add chip data memory read/write support
power: supply: bq27xxx: Add bulk transfer bus methods
dt-bindings: power: supply: bq27xxx: Add monitored-battery documentation
power: supply: core: Add power_supply_prop_precharge
...
|
|
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Battery chargers use POWER_SUPPLY_PROP_PRECHARGE_CURRENT
Clarify related item POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
power_supply_get_battery_info() reads battery data from devicetree.
struct power_supply_battery_info provides battery data to drivers.
Its fields correspond to elements in enum power_supply_property.
Drivers may surface battery data in sysfs via corresponding
POWER_SUPPLY_PROP_* fields.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
|
|
Pull documentation update from Jonathan Corbet:
"A reasonably busy cycle for documentation this time around. There is a
new guide for user-space API documents, rather sparsely populated at
the moment, but it's a start. Markus improved the infrastructure for
converting diagrams. Mauro has converted much of the USB documentation
over to RST. Plus the usual set of fixes, improvements, and tweaks.
There's a bit more than the usual amount of reaching out of
Documentation/ to fix comments elsewhere in the tree; I have acks for
those where I could get them"
* tag 'docs-4.12' of git://git.lwn.net/linux: (74 commits)
docs: Fix a couple typos
docs: Fix a spelling error in vfio-mediated-device.txt
docs: Fix a spelling error in ioctl-number.txt
MAINTAINERS: update file entry for HSI subsystem
Documentation: allow installing man pages to a user defined directory
Doc/PM: Sync with intel_powerclamp code behavior
zr364xx.rst: usb/devices is now at /sys/kernel/debug/
usb.rst: move documentation from proc_usb_info.txt to USB ReST book
convert philips.txt to ReST and add to media docs
docs-rst: usb: update old usbfs-related documentation
arm: Documentation: update a path name
docs: process/4.Coding.rst: Fix a couple of document refs
docs-rst: fix usb cross-references
usb: gadget.h: be consistent at kernel doc macros
usb: composite.h: fix two warnings when building docs
usb: get rid of some ReST doc build errors
usb.rst: get rid of some Sphinx errors
usb/URB.txt: convert to ReST and update it
usb/persist.txt: convert to ReST and add to driver-api book
usb/hotplug.txt: convert to ReST and add to driver-api book
...
|
|
Document the fact that the autosuspend delay and enable helpers may
change the power.usage_count and resume or suspend a device depending on
the values of power.autosuspend_delay and power.use_autosuspend.
Note that this means that a driver must disable autosuspend before
disabling runtime pm on probe errors and on driver unbind if the device
is to be suspended upon return (as a negative delay may otherwise keep
the device resumed).
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Update the autosuspend documentation which claimed that the autosuspend
delay is not taken into account when using the non-autosuspend helper
functions, something which is no longer true since commit d66e6db28df3
("PM / Runtime: Respect autosuspend when idle triggers suspend").
This specifically means that drivers must now disable autosuspend before
disabling runtime pm in probe error paths and remove callbacks if
pm_runtime_put_sync was being used to suspend the device before
returning. (If an idle callback can prevent suspend,
pm_runtime_put_sync_suspend must be used instead of pm_runtime_put_sync
as before.)
Also remove the claim that the autosuspend helpers behave "just like
the non-autosuspend counterparts", something which have never really
been true as some of the latter use idle notifications.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As some USB documentation files got moved, adjust their
cross-references to their new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates deom Rafael Wysocki:
"These fix two bugs introduced by recent power management updates (in
the cpuidle menu governor and intel_pstate) and a few other issues,
clean up things and remove unused code.
Specifics:
- Fix for a cpuidle menu governor problem that started to take an
unnecessary spinlock after one of the recent updates and that did
not play well with the RT patch (Rafael Wysocki).
- Fix for the new intel_pstate operation mode switching feature added
recently that did not reinitialize P-state limits properly when
switching operation modes (Rafael Wysocki).
- Removal of unused global notifiers from the PM QoS framework
(Viresh Kumar).
- Generic power domains framework update to make it handle
asynchronous invocations of PM callbacks in the "noirq" phases of
system suspend/hibernation correctly (Ulf Hansson).
- Two hibernation core cleanups (Rafael Wysocki).
- intel_idle cleanup related to the sysfs interface (Len Brown).
- Off-by-one bug fix in the OPP (Operating Performance Points)
framework (Andrzej Hajda).
- OPP framework's documentation fix (Viresh Kumar).
- cpufreq qoriq driver cleanup (Tang Yuantian).
- Fixes for typos in comments in the device runtime PM framework
(Christophe Jaillet)"
* tag 'pm-extra-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / OPP: Documentation: Fix opp-microvolt in examples
intel_idle: stop exposing platform acronyms in sysfs
cpufreq: intel_pstate: Fix limits issue with operation mode switching
PM / hibernate: Define pr_fmt() and use pr_*() instead of printk()
PM / hibernate: Untangle power_down()
cpuidle: menu: Avoid taking spinlock for accessing QoS values
PM / QoS: Remove global notifiers
PM / runtime: Fix some typos
cpufreq: qoriq: clean up unused code
PM / OPP: fix off-by-one bug in dev_pm_opp_get_max_volt_latency loop
PM / Domains: Power off masters immediately in the power off sequence
PM / Domains: Rename is_async to one_dev_on for genpd_power_off()
PM / Domains: Move genpd_power_off() above genpd_power_on()
|
|
* pm-core:
PM / runtime: Fix some typos
* pm-qos:
PM / QoS: Remove global notifiers
* pm-domains:
PM / Domains: Power off masters immediately in the power off sequence
PM / Domains: Rename is_async to one_dev_on for genpd_power_off()
PM / Domains: Move genpd_power_off() above genpd_power_on()
* pm-opp:
PM / OPP: Documentation: Fix opp-microvolt in examples
PM / OPP: fix off-by-one bug in dev_pm_opp_get_max_volt_latency loop
|
|
They were never used in the kernel, so get rid of them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull documentation updates from Jonathan Corbet:
"A slightly quieter cycle for documentation this time around.
Three more DocBook template files have been converted to RST; only 21
to go. There are various build improvements and the usual array of
documentation improvements and fixes"
* tag 'docs-4.11' of git://git.lwn.net/linux: (44 commits)
docs / driver-api: Fix structure references in device_link.rst
PM / docs: Fix structure references in device.rst
Add a target to check broken external links in the Documentation
Documentation: Fix linux-api list typo
Documentation: DocBook/Makefile comment typo
Improve sparse documentation
Documentation: make Makefile.sphinx no-ops quieter
Documentation: DMA-ISA-LPC.txt
Documentation: input: fix path to input code definitions
docs: Remove the copyright year from conf.py
docs: Fix a warning in the Korean HOWTO.rst translation
PM / sleep / docs: Convert PM notifiers document to reST
PM / core / docs: Convert sleep states API document to reST
PM / core: Update kerneldoc comments in pm.h
doc-rst: Fix recursive make invocation from macros
doc-rst: Delete output of failed dot-SVG conversion
doc-rst: Break shell command sequences on failure
Documentation/sphinx: make targets independent of Sphinx work for HAVE_SPHINX=0
doc-rst: fixed cleandoc target when used with O=dir
Documentation/sphinx: prevent generation of .pyc files in the source tree
...
|
|
* pm-sleep:
PM / Documentation: Spelling s/wrtie/write/
PM / sleep: Fix test_suspend after sleep state rework
PM / Hibernate: Use rb_entry() instead of container_of()
|
|
* pm-opp: (24 commits)
PM / OPP: Expose _of_get_opp_desc_node as dev_pm_opp API
PM / OPP: Make _find_opp_table_unlocked() static
PM / OPP: Update Documentation to remove RCU specific bits
PM / OPP: Simplify dev_pm_opp_get_max_volt_latency()
PM / OPP: Simplify _opp_set_availability()
PM / OPP: Move away from RCU locking
PM / OPP: Take kref from _find_opp_table()
PM / OPP: Update OPP users to put reference
PM / OPP: Add 'struct kref' to struct dev_pm_opp
PM / OPP: Use dev_pm_opp_get_opp_table() instead of _add_opp_table()
PM / OPP: Take reference of the OPP table while adding/removing OPPs
PM / OPP: Return opp_table from dev_pm_opp_set_*() routines
PM / OPP: Add 'struct kref' to OPP table
PM / OPP: Add per OPP table mutex
PM / OPP: Split out part of _add_opp_table() and _remove_opp_table()
PM / OPP: Don't expose srcu_head to register notifiers
PM / OPP: Rename dev_pm_opp_get_suspend_opp() and return OPP rate
PM / OPP: Don't allocate OPP table from _opp_allocate()
PM / OPP: Rename and split _dev_pm_opp_remove_table()
PM / OPP: Add light weight _opp_free() routine
...
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Move the document describing PM notifiers (used during system sleep
state transitions) to Documentation/driver-api/pm/, convert it to reST
and update it to use current terminology. Also replace the remaining
references to the old version of it in .txt documents with references
to the new one.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Move the document describing the system sleep state transitions API
for devices to Documentation/driver-api/pm/, convert it to reST and
update it to use current terminology. Also remove the remaining
reference to the old version of it from pm.h.
The new document still contains references to some documents in the
.txt format that will be converted later.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Update OPP documentation to remove the RCU specific bits.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
* pm-sleep:
Revert "PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag"
* pm-cpufreq:
cpufreq: intel_pstate: Fix sysfs limits enforcement for performance policy
|
|
Revert commit 08b98d329165 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0
flag) as it caused system suspend (in the default configuration) to fail
on Dell XPS13 (9360) with the Kaby Lake processor.
Fixes: 08b98d329165 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag)
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
