| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for the temperatur sensor and the fan controller on the
Microchip LAN966x SoC. Apparently, an Analog Bits PVT sensor is used
which can measure temperature and process voltages. But only a forumlae
for the temperature sensor is known. Additionally, the SoC support a fan
tacho input as well as a PWM signal to control the fan.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220401214032.3738095-5-michael@walle.cc
[groeck: Added missing reference in Documentation/hwmon/index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
controllers
Add support for devices XDPE152C4, XDPE12584.
Signed-off-by: Greg Schwendimann <Greg.Schwendimann@infineon.com>
Link: https://lore.kernel.org/r/5e6d50e9b28140158f339b0de343eea4@infineon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for Maxim MAX77714 PMIC
Removed Drivers:
- Remove support for ST-Ericsson AB8500 DebugFS
New Device Support:
- Add support for Silergy SY7636A to Simple MFD I2C
- Add support for MediaTek MT6366 PMIC to MT6358 IRQ
- Add support for Charger to Intel PMIC CRC
- Add support for Raptor Lake to Intel LPSS PCI
New Functionality:
- Add support for Reboot to Rockchip RK808
Fix-ups:
- Device Tree changes (includcing YAML conversion) for
silergy,sy7636a, maxim,max77843, google,cros-ec, maxim,max14577,
maxim,max77802, maxim,max77714, qcom,tcsr, qcom,spmi-pmic,
stericsson,ab8500, stericsson,db8500-prcmu,
samsung,exynos5433-lpass, mt6397, syscon, brcm,cru
- Visible to menuconfig; simple-mfd-i2c
- Clean-up or clarify code; max77686, intel_soc_pmic_crc
- Improve error handling; mc13xxx-core, stmfx, asic3
- Pass device information to child devices; iqs62x, intel-lpss-acpi
- Individually identify IRQ domains; intel_soc_pmic_core
- Remove superfluous code; dbx500-prcmu, exynos-lpass
- Staticify and constify; arizona-i2c
- Mark sometimes used data as __maybe_unused; atmel-flexcom
- Account for different ACPI tables on AOSP/Windows platforms; arizona-spi
- Use provided (platform) APIs; ab8500-core
- Trivial (whitespace, spelling); rohm-bd9576"
* tag 'mfd-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
dt-bindings: mfd: syscon: Add microchip,lan966x-cpu-syscon compatible
mfd: bd9576: fix typos in comments
mfd: Use platform_get_irq() to get the interrupt
mfd: db8500-prcmu: Remove unused inline function
mfd: arizona-spi: Add Android board ACPI table handling
mfd: arizona-spi: Split Windows ACPI init code into its own function
mfd: asic3: Add missing iounmap() on error asic3_mfd_probe
MAINTAINERS: Rectify entry for ROHM MULTIFUNCTION BD9571MWV-M PMIC DEVICE DRIVERS
mfd: intel-lpss: Provide an SSP type to the driver
dt-bindings: mfd: brcm,cru: Rename pinctrl node
dt-bindings: Add compatibles for undocumented trivial syscons
mfd: atmel-flexcom: Fix compilation warning
dt-bindings: mfd: Add compatible for the MediaTek MT6366 PMIC
dt-bindings: mfd: samsung,exynos5433-lpass: Convert to dtschema
mfd: exynos-lpass: Drop unneeded syscon.h include
mfd: intel-lpss: Add Intel Raptor Lake PCH-S PCI IDs
mfd: ab8500: Drop debugfs module
mfd: sta2x11: Use GFP_KERNEL instead of GFP_ATOMIC
mfd: ab8500: Rewrite bindings in YAML
mfd: qcom-spmi-pmic: Add pm8953 compatible
...
|
|
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
PLI1209BC is a Digital Supervisor from Vicor Corporation.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/4e016e66275bc46c90974aec18b150c874e64787.1645435888.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220124015658.687309-3-eugene.shalygin@gmail.com
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
[groeck: update index.rst, do not drop asus_wmi_ec_sensors.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add documentation for peci-cputemp driver that provides DTS thermal
readings for CPU packages and CPU cores, and peci-dimmtemp driver that
provides Temperature Sensor on DIMM readings.
Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-13-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a multi-function device to interface with the sy7636a
EPD PMIC chip from Silergy.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This driver implements monitoring and control of fans plugged into the
device. Besides typical speed monitoring and PWM duty cycle control,
voltage and current are reported for every fan.
The device also has 2 connectors for RGB LEDs, support for them isn't
implemented (mainly because there is no standardized sysfs interface).
Also, the device has a noise sensor, but the sensor seems to be completely
useless (and very imprecise), so support for it isn't implemented too.
The driver coexists with userspace tools that access the device through
hidraw interface with no known issues.
The driver has been tested on x86_64, built in and as a module.
Some changes/improvements were suggested by Jonas Malaco.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20211031033058.151014-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for mp5023 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a Hot-Swap Controller.
Signed-off-by: Howard Chiu <howard.chiu@quantatw.com>
Link: https://lore.kernel.org/r/HKAPR04MB400349AA406694FB976D78D096709@HKAPR04MB4003.apcprd04.prod.outlook.com
[groeck: Added MODULE_IMPORT_NS, entry in index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Provides a Linux kernel module "asus_wmi_sensors" that provides sensor
readouts via ASUS' WMI interface present in the UEFI of
X370/X470/B450/X399 Ryzen motherboards.
Supported motherboards:
* ROG CROSSHAIR VI HERO,
* PRIME X399-A,
* PRIME X470-PRO,
* ROG CROSSHAIR VI EXTREME,
* ROG CROSSHAIR VI HERO (WI-FI AC),
* ROG CROSSHAIR VII HERO,
* ROG CROSSHAIR VII HERO (WI-FI),
* ROG STRIX B450-E GAMING,
* ROG STRIX B450-F GAMING,
* ROG STRIX B450-I GAMING,
* ROG STRIX X399-E GAMING,
* ROG STRIX X470-F GAMING,
* ROG STRIX X470-I GAMING,
* ROG ZENITH EXTREME,
* ROG ZENITH EXTREME ALPHA.
Co-developed-by: Ed Brindley <kernel@maidavale.org>
Signed-off-by: Ed Brindley <kernel@maidavale.org>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
[groeck: Squashed:
"hwmon: Fix warnings in asus_wmi_sensors.rst documetation."]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Linux HWMON sensors driver for ASUS motherboards to read
sensors from the embedded controller.
Many ASUS motherboards do not publish all the available
sensors via the Super I/O chip but the missing ones are
available through the embedded controller (EC) registers.
This driver implements reading those sensor data via the
WMI method BREC, which is known to be present in all ASUS
motherboards based on the AMD 500 series chipsets (and
probably is available in other models too). The driver
needs to know exact register addresses for the sensors and
thus support for each motherboard has to be added explicitly.
The EC registers do not provide critical values for the
sensors and as such they are not published to the HWMON.
Supported motherboards:
* PRIME X570-PRO
* Pro WS X570-ACE
* ROG CROSSHAIR VIII HERO
* ROG CROSSHAIR VIII DARK HERO
* ROG CROSSHAIR VIII FORMULA
* ROG STRIX X570-E GAMING
* ROG STRIX B550-I GAMING
* ROG STRIX B550-E GAMING
Co-developed-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Tor Vic <torvic9@mailbox.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The INA238 is a I2C power monitor similar to other INA2xx devices,
providing shunt voltage, bus voltage, current, power and temperature
measurements.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20211102052754.817220-3-nathan@nathanrossi.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add hardware monitoring driver for Maxim MAX6620 Fan controller
Originally-from: L. Grunenberg <contact@lgrunenberg.de>
Originally-from: Cumulus Networks <support@cumulusnetworks.com>
Originally-from: Shuotian Cheng <shuche@microsoft.com>
Signed-off-by: Arun Saravanan Balachandran <Arun_Saravanan_Balac@dell.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
- Add documentation for SB-RMI module
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akshay Gupta <Akshay.Gupta@amd.com>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20210726133615.9709-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This adds support for the Delta DPS-920AB PSU.
Only missing feature is fan control which the PSU supports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210607103431.2039073-1-robert.marko@sartura.hr
[groeck: Add MODULE_IMPORT_NS(PMBUS);]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add documentation and index link for pim4328 PMBus driver.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds a hwmon driver for the SHT4x Temperature and
Humidity sensor.
Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
[groeck: dropped unnecessary empty line and continuation lines]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The entry for mp2888 is missing and it causes the following
'make htmldocs' build warning:
Documentation/hwmon/mp2888.rst: WARNING: document isn't included in any toctree
Add the mp2888 entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210521172218.37592-1-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 60268b0e8258 ("hwmon: (amd_energy) modify the visibility of
the counters") restricted visibility of AMD energy counters to work
around a side-channel attack using energy data to determine which
instructions are executed. The attack is described in 'PLATYPUS:
Software-based Power Side-Channel Attacks on x86'. It relies on quick
and accurate energy readings.
This change made the counters provided by the amd_energy driver
effectively unusable for non-provileged users. However, unprivileged
read access is the whole point of hardware monitoring attributes.
An attempt to remedy the situation by limiting and randomizing access
to chip registers was rejected by AMD. Since the driver is for all
practical purposes unusable, remove it.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add pmbus driver support for Maxim MAX15301 InTune Automatically
Compensated Digital PoL Controller with Driver and PMBus Telemetry
Even though the specification does not specifically mention it,
extensive empirical testing has revealed that auto-detection of
limit-registers will fail in a random fashion unless the delay
parameter is set to above about 80us. The default delay is set
to 100us to include some safety margin.
This patch is tested on a Flex BMR461 converter module.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210419101251.24840-1-erik.rosen@metormote.com
[groeck: Added rationale for delay to driver header]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds support for these devices:
- YH-5151E - the PDU
- YM-2151E - the PSU
The device datasheet says that the devices support PMBus 1.2, but in my
testing, a lot of the commands aren't supported and if they are, they
sometimes behave strangely or inconsistently. For example, writes to the
PAGE command requires using PEC, otherwise the write won't work and the
page won't switch, even though, the standard says that PEC is optional.
On the other hand, writes to SMBALERT don't require PEC. Because of
this, the driver is mostly reverse engineered with the help of a tool
called pmbus_peek written by David Brownell (and later adopted by my
colleague Jan Kundrát).
The device also has some sort of a timing issue when switching pages,
which is explained further in the code.
Because of this, the driver support is limited. It exposes only the
values that have been tested to work correctly.
Signed-off-by: Václav Kubernát <kubernat@cesnet.cz>
Link: https://lore.kernel.org/r/20210414080019.3530794-1-kubernat@cesnet.cz
[groeck: Fixed up "missing braces around initializer" from 0-day]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The BPA-RS600 is a compact 600W AC to DC removable power supply module.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210317040231.21490-3-chris.packham@alliedtelesis.co.nz
[groeck: Added bpa-rs600 to index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
These are "all-in-one" CPU liquid coolers that can be monitored and
controlled through a proprietary USB HID protocol.
While the models have differently sized radiators and come with varying
numbers of fans, they are all indistinguishable at the software level.
The driver exposes fan/pump speeds and coolant temperature through the
standard hwmon sysfs interface.
Fan and pump control, while supported by the devices, are not currently
exposed. The firmware accepts up to 61 trip points per channel
(fan/pump), but the same set of trip temperatures has to be maintained
for both; with pwmX_auto_point_Y_temp attributes, users would need to
maintain this invariant themselves.
Instead, fan and pump control, as well as LED control (which the device
also supports for 9 addressable RGB LEDs on the CPU water block) are
left for existing and already mature user-space tools, which can still
be used alongside the driver, thanks to hidraw. A link to one, which I
also maintain, is provided in the documentation.
The implementation is based on USB traffic analysis. It has been
runtime tested on x86_64, both as a built-in driver and as a module.
Signed-off-by: Jonas Malaco <jonas@protocubo.io>
Link: https://lore.kernel.org/r/20210319045544.416138-1-jonas@protocubo.io
[groeck: Removed unnecessary spinlock.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add hardware monitoring support for ST STPDDC60 Unversal Digital
Multicell Controller.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210218115249.28513-3-erik.rosen@metormote.com
[groeck: Fixed whitespace error in Makefile]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The IR36021 is a dual‐loop digital multi‐phase buck controller.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20210301035954.16713-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add basic monitoring support as well as port on/off control for Texas
Instruments TPS23861 PoE PSE IC.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210121134434.2782405-2-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This patch adds a hwmon driver for the AHT10 Temperature and
Humidity sensor. It has a maximum sample rate, as the datasheet
states that the chip may heat up if it is sampled more than once
every two seconds.
Has been tested a to work on a raspberrypi0w
Signed-off-by: Johannes Cornelis Draaijer (datdenkikniet) <jcdra1@gmail.com>
Link: https://lore.kernel.org/r/20210107194014.GA88780@desktop
[groeck: dropped AHT10_ADDR (unused) and use AHT10_MEAS_SIZE where
appropriate; dropped change log]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This deletes the ABx500 hwmon driver, the only supported
variant being the AB8500.
This driver has been replaced by generic frameworks. By
inspecting the abx500 sysfs files we see that it contains
things such as temp1_max, temp1_max_alarm, temp1_max_hyst,
temp1_max_hyst_alarm, temp1_min, temp1_min_alarm.
It becomes obvious that the abx500.c is a reimplementation
of thermal zones. This is not very strange as the generic
thermal zones were not invented when this driver was merged
so people were rolling their own.
The ab8500.c driver contains conversion tables for handling
a thermistor on ADC channels AUX1 and AUX2.
I managed to replace the functionality of the driver with:
- Activation of the ntc_thermistor.c driver,
CONFIG_SENSORS_NTC_THERMISTOR
- Activation of thermal zones, CONFIG_THERMAL
- In the device tree, connecting the NTC driver to the
processed IIO channels from the AB8500 GPADC ADC forming
two instances of NTC sensors.
- Connecting the two NTC sensors to a "chassis" thermal zone
in the device tree and setting that to hit the CPU frequency
at 50 degrees celsius and do a critical shutdown at 70
degrees celsius, deploying a policy using the sensors.
After talking to the original authors we concluded that the
driver was never properly parameterized in production so
what we now have in the device tree is already puts the
thermistors to better use than what the hwmon driver did.
The two remaining channels for two battery temperatures is
already handled in the charging algorithms but can be
optionally extended to thermal zones as well if we want
these to trigger critical shutdown for the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201221125521.768082-1-linus.walleij@linaro.org
[groeck: Removed documentation and fixed up Makefile, Kconfig]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Document the SB-TSI sensor interface driver.
Signed-off-by: Kun Yi <kunyi@google.com>
Link: https://lore.kernel.org/r/20201211215427.3281681-3-kunyi@google.com
[groeck: Added SPDX license identifier, same as source]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC2992 is a rail-to-rail system monitor that
measures current, voltage, and power of two supplies.
Two ADCs simultaneously measure each supply’s current.
A third ADC monitors the input voltages and four
auxiliary external voltages.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver supports Q54SJ108A2 series modules of Delta.
Standard attributes are in sysfs, and other attributes are in debugfs.
Signed-off-by: xiao.ma <xiao.mx.ma@deltaww.com>
Link: https://lore.kernel.org/r/20201202025900.1842-1-max701@126.com
[groeck: Replaced spaces with tabs, dropped excessive spaces,
fixed module prefix in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add the pmbus driver for the STMicroelectronics pm6764 voltage regulator.
the output voltage use the MFR_READ_VOUT 0xD4
vout value returned is linear11
Signed-off-by: Charles Hsu <hsu.yungteng@gmail.com>
[groeck: Fixed various compile errors; marked pm6764tr_of_match __maybe_unused]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add documentation for the max127 hardware monitoring driver.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201123185658.7632-3-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Corsair digital power supplies of the series RMi, HXi and AXi include
a small micro-controller with a lot of sensors attached. The sensors can
be accessed by an USB connector from the outside.
This micro-controller provides the data by a simple proprietary USB HID
protocol. The data consist of temperatures, current and voltage levels,
power usage, uptimes, fan speed and some more. It is also possible to
configure the PSU (fan mode, mono/multi-rail, over current protection).
This driver provides access to the sensors/statistics of the RMi and HXi
series power supplies. It does not support configuring these devices,
because there would be many ways to misconfigure or even damage the PSU.
This patch adds:
- hwmon driver corsair-psu
- hwmon documentation
- updates MAINTAINERS
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/20201027131710.GA253280@monster.powergraphx.local
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
.../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree
List blocks should have blank lines before and after them,
in order to be properly parsed.
Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/b02f98d886ab1f5af233f8999c7a15529fc52cdc.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for initialising shared (between children) Regmaps
- Add support for Kontron SL28CPLD
- Add support for ENE KB3930 Embedded Controller
- Add support for Intel FPGA PAC MAX 10 BMC
New Device Support:
- Add support for Power to Ricoh RN5T618
- Add support for UART to Intel Lakefield
- Add support for LP87524_Q1 to Texas Instruments LP87565
New Functionality:
- Device Tree; ene-kb3930, sl28cpld, syscon, lp87565, lp87524-q1
- Use new helper dev_err_probe(); madera-core, stmfx, wcd934x
- Use new GPIOD API; dm355evm_msp
- Add wake-up capability; sprd-sc27xx-spi
- Add ACPI support; kempld-core
Fix-ups:
- Trivial (spelling/whitespace); Kconfig, ab8500
- Fix for unused variables; khadas-mcu, kempld-core
- Remove unused header file(s); mt6360-core
- Use correct IRQ flags in docs; act8945a, gateworks-gsc, rohm,bd70528-pmic
- Add COMPILE_TEST support; asic3, tmio_core
- Add dependency on I2C; SL28CPLD
Bug Fixes:
- Fix memory leak(s); sm501
- Do not free regmap_config's 'name' until exit; syscon"
* tag 'mfd-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (34 commits)
mfd: kempld-core: Fix unused variable 'kempld_acpi_table' when !ACPI
mfd: sl28cpld: Depend on I2C
mfd: asic3: Build if COMPILE_TEST=y
dt-bindings: mfd: Correct interrupt flags in examples
mfd: Add ACPI support to Kontron PLD driver
mfd: intel-m10-bmc: Add Intel MAX 10 BMC chip support for Intel FPGA PAC
mfd: lp87565: Add LP87524-Q1 variant
dt-bindings: mfd: Add LP87524-Q1
dt-bindings: mfd: lp87565: Convert to yaml
mfd: mt6360: Remove unused include <linux/version.h>
mfd: sm501: Fix leaks in probe()
mfd: syscon: Don't free allocated name for regmap_config
dt-bindings: mfd: syscon: Document Exynos3 and Exynos5433 compatibles
dt-bindings: mfd: syscon: Merge Samsung Exynos Sysreg bindings
dt-bindings: mfd: ab8500: Remove weird Unicode characters
mfd: sprd: Add wakeup capability for PMIC IRQ
mfd: intel-lpss: Add device IDs for UART ports for Lakefield
mfd: dm355evm_msp: Convert LEDs to GPIO descriptor table
mfd: wcd934x: Simplify with dev_err_probe()
mfd: stmfx: Simplify with dev_err_probe()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"New driver and chip support:
- Moortec MR75203 PVT controller
- MPS Multi-phase mp2975 controller
- ADM1266
- Zen3 CPUs
- Intel MAX 10 BMC
Enhancements:
- Support for rated attributes in hwmon core
- MAX20730:
- Device monitoring via debugfs
- VOUT readin adjustment vie devicetree bindings
- LM75:
- Devicetree support
- Regulator support
- Improved accumulationm logic in amd_energy driver
- Added fan sensor to gsc-hwmon driver
- Support for simplified I2C probing
Various other minor fixes and improvements"
* tag 'hwmon-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (64 commits)
hwmon: (pmbus/max20730) adjust the vout reading given voltage divider
dt-bindings: hwmon: max20730: adding device tree doc for max20730
hwmon: Add hardware monitoring driver for Moortec MR75203 PVT controller
hwmon: Add DT bindings schema for PVT controller
dt-bindings: hwmon: Add the +vs supply to the lm75 bindings
dt-bindings: hwmon: Convert lm75 bindings to yaml
docs: hwmon: (ltc2945) update datasheet link
hwmon: (mlxreg-fan) Fix double "Mellanox"
hwmon: (pmbus/max20730) add device monitoring via debugfs
hwmon: (pmbus/max34440) Fix OC fault limits
hwmon: (bt1-pvt) Wait for the completion with timeout
hwmon: (bt1-pvt) Cache current update timeout
hwmon: (bt1-pvt) Test sensor power supply on probe
hwmon: (lm75) Add regulator support
hwmon: Add hwmon driver for Intel MAX 10 BMC
dt-bindings: Add MP2975 voltage regulator device
hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller
hwmon: (tmp513) fix spelling typo in comments
hwmon: (amd_energy) Update driver documentation
hwmon: (amd_energy) Improve the accumulation logic
...
|
|
This patch adds hwmon functionality for Intel MAX 10 BMC chip. This BMC
chip connects to a set of sensor chips to monitor current, voltage,
thermal and power of different components on board. The BMC firmware is
responsible for sensor data sampling and recording in shared registers.
Host driver reads the sensor data from these shared registers and
exposes them to users as hwmon interfaces.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1600669071-26235-3-git-send-email-yilun.xu@intel.com
[groeck: Adjusted subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add pmbus probing driver for the adm1266 Cascadable
Super Sequencer with Margin Control and Fault Recording.
Driver is using the pmbus_core, creating sysfs files
under hwmon for inputs: vh1->vh4 and vp1->vp13.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-2-alexandru.tachici@analog.com
[groeck: Use .probe_new function, adjust for changed pmbus_do_probe API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There were some new file additions for Kernel 5.7 and 5.8
that weren't added at the corresponding index file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/9fd4d04f0d122ff38b5342a0098d99cc2f546652.1599660067.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This is v7 of a driver for the Corsair Commander Pro.
It provides sysfs attributes for:
- Reading fan speed
- Reading temp sensors
- Reading voltage values
- Writing pwm and reading last written pwm
- Reading fan and temp connection status
It is an usb driver, so it needs to be ignored by usbhid.
The Corsair Commander Pro is a fan controller and provides
no means for user interaction.
The two device numbers are there, because there is a slightly
different version of the same device. (Only difference
seem to be in some presets.)
Squashed:
hwmon: (corsair-cpro) add fan_target
This adds fan_target entries to the corsair-cpro driver.
Reading the attribute from the device does not seem possible, so
it returns the last set value (same as pwm).
send_usb_cmd now has one more argument, which is needed for the
fan_target command.
hwmon: corsair-cpro: Change to HID driver
This changes corsair-cpro to a hid driver using hid reports.
Signed-off-by: Marius Zachmann <mail@mariuszachmann.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200626055936.4441-1-mail@mariuszachmann.de
Link: https://lore.kernel.org/r/20200709141413.30790-1-mail@mariuszachmann.de
[groeck: Squashed follow-up patches to avoid changes in HID code]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
Baikal-T1 SoC provides an embedded process, voltage and temperature
sensor to monitor an internal SoC environment (chip temperature, supply
voltage and process monitor) and on time detect critical situations,
which may cause the system instability and even damages. The IP-block
is based on the Analog Bits PVT sensor, but is equipped with a
dedicated control wrapper, which provides a MMIO registers-based access
to the sensor core functionality (APB3-bus based) and exposes an
additional functions like thresholds/data ready interrupts, its status
and masks, measurements timeout. All of these is used to create a hwmon
driver being added to the kernel by this commit.
The driver implements support for the hardware monitoring capabilities
of Baikal-T1 process, voltage and temperature sensors. PVT IP-core
consists of one temperature and four voltage sensors, each of which is
implemented as a dedicated hwmon channel config.
The driver can optionally provide the hwmon alarms for each sensor the
PVT controller supports. The alarms functionality is made compile-time
configurable due to the hardware interface implementation peculiarity,
which is connected with an ability to convert data from only one sensor
at a time. Additional limitation is that the controller performs the
thresholds checking synchronously with the data conversion procedure.
Due to these limitations in order to have the hwmon alarms
automatically detected the driver code must switch from one sensor to
another, read converted data and manually check the threshold status
bits. Depending on the measurements timeout settings this design may
cause additional burden on the system performance. By default if the
alarms kernel config is disabled the data conversion is performed by
the driver on demand when read operation is requested via corresponding
_input-file.
Co-developed-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Maxim Kaurkin <maxim.kaurkin@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Immutable branch between MFD and HWMON due for the v5.8 merge window
|
|
Document amd_energy driver with energy sensors supported by it.
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20200519155011.56184-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
MAX16601 is a VR13.HC Dual-Output Voltage Regulator Chipset,
implementing a (8+1) multiphase synchronous buck converter.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
