| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When DWC3 is set to host mode by programming register DWC3_GCTL, VBUS
(or its control signal) will turn on immediately on related Root Hub
ports. Then the VBUS will be de-asserted for a little while during xhci
reset (conducted by xhci driver) for a little while and back to normal.
This VBUS glitch might cause some USB devices emuration fail if kernel
boot with them connected. One SW workaround which can fix this is to
program all PORTSC[PP] to 0 to turn off VBUS immediately after setting
host mode in DWC3 driver(per signal measurement result, it will be too
late to do it in xhci-plat.c or xhci.c).
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-3-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The vbus-regulator property was never actually read from the device tree.
Introduce a new property vbus-supply to represent the regulator powering
the VBUS when acting as an A-Device. This supply will be enabled and
disabled as necessary. Note that this is different from vbus-regulator,
which represented the available current available to draw from VBUS in
B-Device mode. Because no one was using vbus-regulator, remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240123225111.1629405-2-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Of the four USB controllers present on the MediaTek MT8195 SoC, three
of them (0, 2 and 3) are behind MTU3: add wakeup controls for them.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240122111809.148546-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"usb-phy" has multiple type definitions. Unify the type with the looser
definition, phandle-array, as there are cases with multiple entries
(USB2 and USB3). However, the 'phandle-array' type alone is a bit
ambiguous. It can be either just an array of phandles or an array of
phandles plus args. "usb-phy" is the former and needs to constrain each
entry to a single phandle value.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240124190725.1554080-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Several bindings implement parts of Type-C USB orientation and mode
switching, and retiming. Keep definition of such properties in one
place, new usb-switch schema, to avoid duplicate defines.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240122094406.32198-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Marvell ac5 device tree bindings to generic EHCI.
This compatible enables the Marvell Orion platform code
to properly configure the DMA mask for the Marvell AC5 SOC.
Signed-off-by: Elad Nachman <enachman@marvell.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240114172154.2622275-2-enachman@marvell.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce a binding for the ITE IT5205 Alternate Mode Passive MUX,
used for connecting, disconnecting and switching orientation and
control the SBU signals for alternate modes on USB Type-C ports.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240122110446.140226-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers"
* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
clocksource/drivers/ep93xx: Fix error handling during probe
clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
clocksource/timer-riscv: Add riscv_clock_shutdown callback
dt-bindings: timer: Add StarFive JH8100 clint
dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- Loongson LS2X APB DMA controller
- sf-pdma: mpfs-pdma support
- Qualcomm X1E80100 GPI dma controller support
Updates:
- Xilinx XDMA updates to support interleaved DMA transfers
- TI PSIL threads for AM62P and J722S and cfg register regions
description
- axi-dmac Improving the cyclic DMA transfers
- Tegra Support dma-channel-mask property
- Remaining platform remove callback returning void conversions
Driver fixes for:
- Xilinx xdma driver operator precedence and initialization fix
- Excess kernel-doc warning fix in imx-sdma xilinx xdma drivers
- format-overflow warning fix for rz-dmac, sh usb dmac drivers
- 'output may be truncated' fix for shdma, fsl-qdma and dw-edma
drivers"
* tag 'dmaengine-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (58 commits)
dmaengine: dw-edma: increase size of 'name' in debugfs code
dmaengine: fsl-qdma: increase size of 'irq_name'
dmaengine: shdma: increase size of 'dev_id'
dmaengine: xilinx: xdma: Fix kernel-doc warnings
dmaengine: usb-dmac: Avoid format-overflow warning
dmaengine: sh: rz-dmac: Avoid format-overflow warning
dmaengine: imx-sdma: fix Excess kernel-doc warnings
dmaengine: xilinx: xdma: Fix initialization location of desc in xdma_channel_isr()
dmaengine: xilinx: xdma: Fix operator precedence in xdma_prep_interleaved_dma()
dmaengine: xilinx: xdma: statify xdma_prep_interleaved_dma
dmaengine: xilinx: xdma: Workaround truncation compilation error
dmaengine: pl330: issue_pending waits until WFP state
dmaengine: xilinx: xdma: Implement interleaved DMA transfers
dmaengine: xilinx: xdma: Prepare the introduction of interleaved DMA transfers
dmaengine: xilinx: xdma: Add transfer error reporting
dmaengine: xilinx: xdma: Add error checking in xdma_channel_isr()
dmaengine: xilinx: xdma: Rework xdma_terminate_all()
dmaengine: xilinx: xdma: Ease dma_pool alignment requirements
dmaengine: xilinx: xdma: Add necessary macro definitions
dmaengine: xilinx: xdma: Get rid of unused code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- Support for tuning for systems with fast misaligned accesses.
- Support for SBI-based suspend.
- Support for the new SBI debug console extension.
- The T-Head CMOs now use PA-based flushes.
- Support for enabling the V extension in kernel code.
- Optimized IP checksum routines.
- Various ftrace improvements.
- Support for archrandom, which depends on the Zkr extension.
- The build is no longer broken under NET=n, KUNIT=y for ports that
don't define their own ipv6 checksum.
* tag 'riscv-for-linus-6.8-mw4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (56 commits)
lib: checksum: Fix build with CONFIG_NET=n
riscv: lib: Check if output in asm goto supported
riscv: Fix build error on rv32 + XIP
riscv: optimize ELF relocation function in riscv
RISC-V: Implement archrandom when Zkr is available
riscv: Optimize hweight API with Zbb extension
riscv: add dependency among Image(.gz), loader(.bin), and vmlinuz.efi
samples: ftrace: Add RISC-V support for SAMPLE_FTRACE_DIRECT[_MULTI]
riscv: ftrace: Add DYNAMIC_FTRACE_WITH_DIRECT_CALLS support
riscv: ftrace: Make function graph use ftrace directly
riscv: select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
lib/Kconfig.debug: Update AS_HAS_NON_CONST_LEB128 comment and name
riscv: Restrict DWARF5 when building with LLVM to known working versions
riscv: Hoist linker relaxation disabling logic into Kconfig
kunit: Add tests for csum_ipv6_magic and ip_fast_csum
riscv: Add checksum library
riscv: Add checksum header
riscv: Add static key for misaligned accesses
asm-generic: Improve csum_fold
RISC-V: selftests: cbo: Ensure asm operands match constraints
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Raise minimum clang version to 18.0.0
- Enable initial Rust support for LoongArch
- Add built-in dtb support for LoongArch
- Use generic interface to support crashkernel=X,[high,low]
- Some bug fixes and other small changes
- Update the default config file.
* tag 'loongarch-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: (22 commits)
MAINTAINERS: Add BPF JIT for LOONGARCH entry
LoongArch: Update Loongson-3 default config file
LoongArch: BPF: Prevent out-of-bounds memory access
LoongArch: BPF: Support 64-bit pointers to kfuncs
LoongArch: Fix definition of ftrace_regs_set_instruction_pointer()
LoongArch: Use generic interface to support crashkernel=X,[high,low]
LoongArch: Fix and simplify fcsr initialization on execve()
LoongArch: Let cores_io_master cover the largest NR_CPUS
LoongArch: Change SHMLBA from SZ_64K to PAGE_SIZE
LoongArch: Add a missing call to efi_esrt_init()
LoongArch: Parsing CPU-related information from DTS
LoongArch: dts: DeviceTree for Loongson-2K2000
LoongArch: dts: DeviceTree for Loongson-2K1000
LoongArch: dts: DeviceTree for Loongson-2K0500
LoongArch: Allow device trees be built into the kernel
dt-bindings: interrupt-controller: loongson,liointc: Fix dtbs_check warning for interrupt-names
dt-bindings: interrupt-controller: loongson,liointc: Fix dtbs_check warning for reg-names
dt-bindings: loongarch: Add Loongson SoC boards compatibles
dt-bindings: loongarch: Add CPU bindings for LoongArch
LoongArch: Enable initial Rust support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- Lots of ASoC SOF fixes and related reworks
- ASoC TAS codec fixes including DT updates
- A few HD-audio quirks and regression fixes
- Minor fixes for aloop, oxygen and scarlett2 mixer"
* tag 'sound-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek: Enable headset mic on Lenovo M70 Gen5
ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on HP ZBook
ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx
ASoC: SOF: ipc4-loader: remove the CPC check warnings
ASoC: SOF: ipc4-pcm: remove log message for LLP
ALSA: hda: generic: Remove obsolete call to ledtrig_audio_get
ALSA: scarlett2: Fix yet more -Wformat-truncation warnings
ALSA: hda: Properly setup HDMI stream
ASoC: audio-graph-card2: fix index check on graph_parse_node_multi_nm()
ASoC: SOF: icp3-dtrace: Revert "Fix wrong kfree() usage"
ALSA: oxygen: Fix right channel of capture volume mixer
ALSA: aloop: Introduce a function to get if access is interleaved mode
ASoC: mediatek: sof-common: Add NULL check for normal_link string
ASoC: mediatek: mt8195: Remove afe-dai component and rework codec link
ASoC: mediatek: mt8192: Check existence of dai_name before dereferencing
ASoC: Intel: bxt_rt298: Fix kernel ops due to COMP_DUMMY change
ASoC: Intel: bxt_da7219_max98357a: Fix kernel ops due to COMP_DUMMY change
ASoC: codecs: rtq9128: Fix TDM enable and DAI format control flow
ASoC: codecs: rtq9128: Fix PM_RUNTIME usage
ASoC: tas2781: Add tas2563 into driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"New features:
- bq24190: Add support for BQ24296 charger
Cleanups:
- all reset drivers: Stop using module_platform_driver_probe()
- gpio-restart: use devm_register_sys_off_handler
- pwr-mlxbf: support graceful reboot
- cw2015: correct time_to_empty units
- qcom-battmgr: Fix driver initialization sequence
- bq27xxx: Start/Stop delayed work in suspend/resume
- minor cleanups and fixes"
* tag 'for-v6.8-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (33 commits)
power: supply: bq24190_charger: Fix "initializer element is not constant" error
power: supply: bq24190_charger: Add support for BQ24296
dt-bindings: power: supply: bq24190: Add BQ24296 compatible
dt-bindings: power: reset: xilinx: Rename node names in examples
power: supply: qcom_battmgr: Register the power supplies after PDR is up
dt-bindings: power: reset: qcom-pon: fix inconsistent example
power: supply: Fix null pointer dereference in smb2_probe
power: reset: at91: Drop '__init' from at91_wakeup_status()
power: supply: Use multiple MODULE_AUTHOR statements
power: supply: Fix indentation and some other warnings
power: reset: gpio-restart: Use devm_register_sys_off_handler()
power: supply: bq256xx: fix some problem in bq256xx_hw_init
power: supply: cw2015: correct time_to_empty units in sysfs
power: reset: at91-sama5d2_shdwc: Convert to platform remove callback returning void
power: reset: at91-reset: Convert to platform remove callback returning void
power: reset: tps65086-restart: Convert to platform remove callback returning void
power: reset: syscon-poweroff: Convert to platform remove callback returning void
power: reset: rmobile-reset: Convert to platform remove callback returning void
power: reset: restart-poweroff: Convert to platform remove callback returning void
power: reset: regulator-poweroff: Convert to platform remove callback returning void
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There are three new drivers this cycle. Also the cmos driver is
getting fixes for longstanding wakeup issues on AMD.
New drivers:
- Analog Devices MAX31335
- Nuvoton ma35d1
- Texas Instrument TPS6594 PMIC RTC
Drivers:
- cmos: use ACPI alarm instead of HPET on recent AMD platforms
- nuvoton: add NCT3015Y-R and NCT3018Y-R support
- rv8803: proper suspend/resume and wakeup-source support"
* tag 'rtc-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (26 commits)
rtc: nuvoton: Compatible with NCT3015Y-R and NCT3018Y-R
rtc: da9063: Use dev_err_probe()
rtc: da9063: Use device_get_match_data()
rtc: da9063: Make IRQ as optional
rtc: max31335: Fix comparison in max31335_volatile_reg()
rtc: max31335: use regmap_update_bits_check
rtc: max31335: remove unecessary locking
rtc: max31335: add driver support
dt-bindings: rtc: max31335: add max31335 bindings
rtc: rv8803: add wakeup-source support
rtc: ac100: remove misuses of kernel-doc
rtc: class: Remove usage of the deprecated ida_simple_xx() API
rtc: MAINTAINERS: drop Alessandro Zummo
rtc: ma35d1: remove hardcoded UIE support
dt-bindings: rtc: qcom-pm8xxx: fix inconsistent example
rtc: rv8803: Add power management support
rtc: ds3232: avoid unused-const-variable warning
rtc: lpc24xx: add missing dependency
rtc: tps6594: Add driver for TPS6594 RTC
rtc: Add driver for Nuvoton ma35d1 rtc controller
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for Adafruit Seesaw gamepad device
- Zforce touchscreen will handle standard device properties for axis
swap/inversion
- handling of advanced sensitivity settings in Microchip CAP11xx
capacitive sensor driver
- more drivers have been converted to use newer gpiod API
- support for dedicated wakeup IRQs in gpio-keys dirver
- support for slider gestures and OTP variants in iqs269a driver
- atkbd will report keyboard version as 0xab83 in cases when GET ID
command was skipped (to deal with problematic firmware on newer
laptops), restoring the previous behavior
- other assorted cleanups and changes
* tag 'input-for-v6.8-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (44 commits)
Input: atkbd - use ab83 as id when skipping the getid command
Input: driver for Adafruit Seesaw Gamepad
dt-bindings: input: bindings for Adafruit Seesaw Gamepad
Input: da9063_onkey - avoid explicitly setting input's parent
Input: da9063_onkey - avoid using OF-specific APIs
Input: iqs269a - add support for OTP variants
dt-bindings: input: iqs269a: Add bindings for OTP variants
Input: iqs269a - add support for slider gestures
dt-bindings: input: iqs269a: Add bindings for slider gestures
Input: gpio-keys - filter gpio_keys -EPROBE_DEFER error messages
Input: zforce_ts - accept standard touchscreen properties
dt-bindings: touchscreen: neonode,zforce: Use standard properties
dt-bindings: touchscreen: convert neonode,zforce to json-schema
dt-bindings: input: convert drv266x to json-schema
Input: da9063 - use dev_err_probe()
Input: da9063 - drop redundant prints in probe()
Input: da9063 - simplify obtaining OF match data
Input: as5011 - convert to GPIO descriptor
Input: omap-keypad - drop optional GPIO support
Input: tca6416-keypad - drop unused include
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support:
- Qualcomm SM8650 UFS, PCIe and USB/DP Combo PHY, eUSB2 PHY, SDX75
USB3, X1E80100 USB3 support
- Mediatek MT8195 support
- Rockchip RK3128 usb2 support
- TI SGMII mode for J784S4
Updates:
- Qualcomm v7 register offsets updates
- Mediatek tphy support for force phy mode switch"
* tag 'phy-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (34 commits)
phy: ti: j721e-wiz: Add SGMII support in WIZ driver for J784S4
phy: ti: gmii-sel: Enable SGMII mode for J784S4
phy: qcom-qmp-usb: Add Qualcomm X1E80100 USB3 PHY support
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add X1E80100 USB PHY binding
phy: qcom-qmp-combo: Add x1e80100 USB/DP combo phys
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: Document X1E80100 compatible
dt-bindings: phy: qcom: snps-eusb2: Document the X1E80100 compatible
phy: mediatek: tphy: add support force phy mode switch
dt-bindings: phy: mediatek: tphy: add a property for force-mode switch
phy: phy-can-transceiver: insert space after include
phy: qualcomm: phy-qcom-qmp-ufs: Rectify SM8550 UFS HS-G4 PHY Settings
dt-bindings: phy: qcom,sc8280xp-qmp-usb43dp-phy: fix path to header
phy: renesas: phy-rcar-gen2: use select for GENERIC_PHY
phy: qcom-qmp: qserdes-txrx: Add v7 register offsets
phy: qcom-qmp: qserdes-txrx: Add V6 N4 register offsets
phy: qcom-qmp: qserdes-com: Add v7 register offsets
phy: qcom-qmp: pcs-usb: Add v7 register offsets
phy: qcom-qmp: pcs: Add v7 register offsets
phy: qcom-qmp: qserdes-txrx: Add some more v6.20 register offsets
phy: qcom-qmp: qserdes-com: Add some more v6 register offsets
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"Apart from some regular driver fixes there's a relatively big revert
of the locking changes that were introduced to GPIOLIB in this merge
window.
This is because it turned out that some legacy GPIO interfaces - that
need to translate a number from the global GPIO numberspace to the
address of the relevant descriptor, thus running a GPIO device lookup
and taking the GPIO device list lock - are still used in old code from
atomic context resulting in "scheduling while atomic" errors.
I'll try to make the read-only part of the list access entirely
lockless using SRCU but this will take some time so let's go back to
the old global spinlock for now.
Summary:
- revert the changes aiming to use a read-write semaphore to protect
the list of GPIO devices due to calls to legacy API taking that
lock from atomic context in old code
- fix inverted logic in DEFINE_FREE() for GPIO device references
- check the return value of bgpio_init() in gpio-mlxbf3
- fix node address in the DT bindings example for gpio-xilinx
- fix signedness bug in gpio-rtd
- fix kernel-doc warnings in gpio-en7523"
* tag 'gpio-fixes-for-v6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: revert the attempt to protect the GPIO device list with an rwsem
gpio: EN7523: fix kernel-doc warnings
gpiolib: Fix scope-based gpio_device refcounting
gpio: mlxbf3: add an error code check in mlxbf3_gpio_probe
dt-bindings: gpio: xilinx: Fix node address in gpio
gpio: rtd: Fix signedness bug in probe
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"New Drivers:
- Add support for Monolithic Power Systems MP3309C WLED Step-up Converter
Fix-ups:
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree Binding updates
- Demote non-kerneldoc header comments
- Improve error handling; return proper error values, simplify, avoid
duplicates, etc
- Convert over to the new (kinda) GPIOD API
Bug Fixes:
- Fix uninitialised local variable"
* tag 'backlight-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: hx8357: Convert to agnostic GPIO API
backlight: ili922x: Add an error code check in ili922x_write()
backlight: ili922x: Drop kernel-doc for local macros
backlight: mp3309c: Fix uninitialized local variable
backlight: pwm_bl: Use dev_err_probe
backlight: mp3309c: Add support for MPS MP3309C
dt-bindings: backlight: mp3309c: Remove two required properties
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"Core changes:
- Fix race conditions in device probe path
- Retire IOMMU bus_ops
- Support for passing custom allocators to page table drivers
- Clean up Kconfig around IOMMU_SVA
- Support for sharing SVA domains with all devices bound to a mm
- Firmware data parsing cleanup
- Tracing improvements for iommu-dma code
- Some smaller fixes and cleanups
ARM-SMMU drivers:
- Device-tree binding updates:
- Add additional compatible strings for Qualcomm SoCs
- Document Adreno clocks for Qualcomm's SM8350 SoC
- SMMUv2:
- Implement support for the ->domain_alloc_paging() callback
- Ensure Secure context is restored following suspend of Qualcomm
SMMU implementation
- SMMUv3:
- Disable stalling mode for the "quiet" context descriptor
- Minor refactoring and driver cleanups
Intel VT-d driver:
- Cleanup and refactoring
AMD IOMMU driver:
- Improve IO TLB invalidation logic
- Small cleanups and improvements
Rockchip IOMMU driver:
- DT binding update to add Rockchip RK3588
Apple DART driver:
- Apple M1 USB4/Thunderbolt DART support
- Cleanups
Virtio IOMMU driver:
- Add support for iotlb_sync_map
- Enable deferred IO TLB flushes"
* tag 'iommu-updates-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (66 commits)
iommu: Don't reserve 0-length IOVA region
iommu/vt-d: Move inline helpers to header files
iommu/vt-d: Remove unused vcmd interfaces
iommu/vt-d: Remove unused parameter of intel_pasid_setup_pass_through()
iommu/vt-d: Refactor device_to_iommu() to retrieve iommu directly
iommu/sva: Fix memory leak in iommu_sva_bind_device()
dt-bindings: iommu: rockchip: Add Rockchip RK3588
iommu/dma: Trace bounce buffer usage when mapping buffers
iommu/arm-smmu: Convert to domain_alloc_paging()
iommu/arm-smmu: Pass arm_smmu_domain to internal functions
iommu/arm-smmu: Implement IOMMU_DOMAIN_BLOCKED
iommu/arm-smmu: Convert to a global static identity domain
iommu/arm-smmu: Reorganize arm_smmu_domain_add_master()
iommu/arm-smmu-v3: Remove ARM_SMMU_DOMAIN_NESTED
iommu/arm-smmu-v3: Master cannot be NULL in arm_smmu_write_strtab_ent()
iommu/arm-smmu-v3: Add a type for the STE
iommu/arm-smmu-v3: disable stall for quiet_cd
iommu/qcom: restore IOMMU state if needed
iommu/arm-smmu-qcom: Add QCM2290 MDSS compatible
iommu/arm-smmu-qcom: Add missing GMU entry to match table
...
|
|
Add a new compatible st,stm32mp25-i2c for the STM32MP25 series which
has only one interrupt line for both events and errors and differs in
term of handling of FastModePlus.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add compatible for ROHM Semiconductor BR24G04 EEPROMs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Roland Hieber <rhi@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt changes for 6.8-rc1.
Included in here are the following:
- Thunderbolt subsystem and driver updates for USB 4 hardware and
issues reported by real devices
- xhci driver updates
- dwc3 driver updates
- uvc_video gadget driver updates
- typec driver updates
- gadget string functions cleaned up
- other small changes
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'usb-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: typec: tipd: fix use of device-specific init function
usb: typec: tipd: Separate reset for TPS6598x
usb: mon: Fix atomicity violation in mon_bin_vma_fault
usb: gadget: uvc: Remove nested locking
usb: gadget: uvc: Fix use are free during STREAMOFF
usb: typec: class: fix typec_altmode_put_partner to put plugs
dt-bindings: usb: dwc3: Limit num-hc-interrupters definition
dt-bindings: usb: xhci: Add num-hc-interrupters definition
xhci: add support to allocate several interrupters
USB: core: Use device_driver directly in struct usb_driver and usb_device_driver
arm64: dts: mediatek: mt8195: Add 'rx-fifo-depth' for cherry
usb: xhci-mtk: fix a short packet issue of gen1 isoc-in transfer
dt-bindings: usb: mtk-xhci: add a property for Gen1 isoc-in transfer issue
arm64: dts: qcom: msm8996: Remove PNoC clock from MSS
arm64: dts: qcom: msm8996: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8998: Remove AGGRE2 clock from SLPI
arm64: dts: qcom: msm8939: Drop RPM bus clocks
arm64: dts: qcom: sdm630: Drop RPM bus clocks
arm64: dts: qcom: qcs404: Drop RPM bus clocks
arm64: dts: qcom: msm8996: Drop RPM bus clocks
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.8-rc1.
As usual, Jiri has a bunch of refactoring and cleanups for the tty
core and drivers in here, along with the usual set of rs485 updates
(someday this might work properly...)
Along with those, in here are changes for:
- sc16is7xx serial driver updates
- platform driver removal api updates
- amba-pl011 driver updates
- tty driver binding updates
- other small tty/serial driver updates and changes
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (197 commits)
serial: sc16is7xx: refactor EFR lock
serial: sc16is7xx: reorder code to remove prototype declarations
serial: sc16is7xx: refactor FIFO access functions to increase commonality
serial: sc16is7xx: drop unneeded MODULE_ALIAS
serial: sc16is7xx: replace hardcoded divisor value with BIT() macro
serial: sc16is7xx: add explicit return for some switch default cases
serial: sc16is7xx: add macro for max number of UART ports
serial: sc16is7xx: add driver name to struct uart_driver
serial: sc16is7xx: use i2c_get_match_data()
serial: sc16is7xx: use spi_get_device_match_data()
serial: sc16is7xx: use DECLARE_BITMAP for sc16is7xx_lines bitfield
serial: sc16is7xx: improve do/while loop in sc16is7xx_irq()
serial: sc16is7xx: remove obsolete loop in sc16is7xx_port_irq()
serial: sc16is7xx: set safe default SPI clock frequency
serial: sc16is7xx: add check for unsupported SPI modes during probe
serial: sc16is7xx: fix invalid sc16is7xx_lines bitfield in case of probe error
serial: 8250_exar: Set missing rs485_supported flag
serial: omap: do not override settings for RS485 support
serial: core, imx: do not set RS485 enabled if it is not supported
serial: core: make sure RS485 cannot be enabled when it is not supported
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem changes
for 6.8-rc1.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (341 commits)
android: removed duplicate linux/errno
uio: Fix use-after-free in uio_open
drivers: soc: xilinx: add check for platform
firmware: xilinx: Export function to use in other module
scripts/tags.sh: remove find_sources
scripts/tags.sh: use -n to test archinclude
scripts/tags.sh: add local annotation
scripts/tags.sh: use more portable -path instead of -wholename
scripts/tags.sh: Update comment (addition of gtags)
firmware: zynqmp: Convert to platform remove callback returning void
firmware: turris-mox-rwtm: Convert to platform remove callback returning void
firmware: stratix10-svc: Convert to platform remove callback returning void
firmware: stratix10-rsu: Convert to platform remove callback returning void
firmware: raspberrypi: Convert to platform remove callback returning void
firmware: qemu_fw_cfg: Convert to platform remove callback returning void
firmware: mtk-adsp-ipc: Convert to platform remove callback returning void
firmware: imx-dsp: Convert to platform remove callback returning void
firmware: coreboot_table: Convert to platform remove callback returning void
firmware: arm_scpi: Convert to platform remove callback returning void
firmware: arm_scmi: Convert to platform remove callback returning void
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Reserve ECAM so we don't assign it to PCI BARs; this works around
bugs where BIOS included ECAM in a PNP0A03 host bridge window,
didn't reserve it via a PNP0C02 motherboard device, and didn't
allocate space for SR-IOV VF BARs (Bjorn Helgaas)
- Add MMCONFIG/ECAM debug logging (Bjorn Helgaas)
- Rename 'MMCONFIG' to 'ECAM' to match spec usage (Bjorn Helgaas)
- Log device type (Root Port, Switch Port, etc) during enumeration
(Bjorn Helgaas)
- Log bridges before downstream devices so the dmesg order is more
logical (Bjorn Helgaas)
- Log resource names (BAR 0, VF BAR 0, bridge window, etc)
consistently instead of a mix of names and "reg 0x10" (Puranjay
Mohan, Bjorn Helgaas)
- Fix 64GT/s effective data rate calculation to use 1b/1b encoding
rather than the 8b/10b or 128b/130b used by lower rates (Ilpo
Järvinen)
- Use PCI_HEADER_TYPE_* instead of literals in x86, powerpc, SCSI
lpfc (Ilpo Järvinen)
- Clean up open-coded PCIBIOS return code mangling (Ilpo Järvinen)
Resource management:
- Restructure pci_dev_for_each_resource() to avoid computing the
address of an out-of-bounds array element (the bounds check was
performed later so the element was never actually *read*, but it's
nicer to avoid even computing an out-of-bounds address) (Andy
Shevchenko)
Driver binding:
- Convert pci-host-common.c platform .remove() callback to
.remove_new() returning 'void' since it's not useful to return
error codes here (Uwe Kleine-König)
- Convert exynos, keystone, kirin from .remove() to .remove_new(),
which returns void instead of int (Uwe Kleine-König)
- Drop unused struct pci_driver.node member (Mathias Krause)
Virtualization:
- Add ACS quirk for more Zhaoxin Root Ports (LeoLiuoc)
Error handling:
- Log AER errors as "Correctable" (not "Corrected") or
"Uncorrectable" to match spec terminology (Bjorn Helgaas)
- Decode Requester ID when no error info found instead of printing
the raw hex value (Bjorn Helgaas)
Endpoint framework:
- Use a unique test pattern for each BAR in the pci_endpoint_test to
make it easier to debug address translation issues (Niklas Cassel)
Broadcom STB PCIe controller driver:
- Add DT property "brcm,clkreq-mode" and driver support for different
CLKREQ# modes to make ASPM L1.x states possible (Jim Quinlan)
Freescale Layerscape PCIe controller driver:
- Add suspend/resume support for Layerscape LS1043a and LS1021a,
including software-managed PME_Turn_Off and transitions between L0,
L2/L3_Ready Link states (Frank Li)
MediaTek PCIe controller driver:
- Clear MSI interrupt status before handler to avoid missing MSIs
that occur after the handler (qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 translation window setup to handle MMIO space
that is not a power of two in size (Jianjun Wang)
Qualcomm PCIe controller driver:
- Increase qcom iommu-map maxItems to accommodate SDX55 (five
entries) and SDM845 (sixteen entries) (Krzysztof Kozlowski)
- Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof
Kozlowski)
- Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof
Kozlowski)
- Correct the qcom "reset-name" property, previously incorrectly
called "reset-names" (Krzysztof Kozlowski)
- Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil
Armstrong)
Renesas R-Car PCIe controller driver:
- Replace of_device.h with explicit of.h include to untangle header
usage (Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v
regulators on KingFisher (Wolfram Sang)
SiFive FU740 PCIe controller driver:
- Convert fu740 CONFIG_PCIE_FU740 dependency from SOC_SIFIVE to
ARCH_SIFIVE (Conor Dooley)
Synopsys DesignWare PCIe controller driver:
- Align iATU mapping for endpoint MSI-X (Niklas Cassel)
- Drop "host_" prefix from struct dw_pcie_host_ops members (Yoshihiro
Shimoda)
- Drop "ep_" prefix from struct dw_pcie_ep_ops members (Yoshihiro
Shimoda)
- Rename struct dw_pcie_ep_ops.func_conf_select() to
.get_dbi_offset() to be more descriptive (Yoshihiro Shimoda)
- Add Endpoint DBI accessors to encapsulate offset lookups (Yoshihiro
Shimoda)
TI J721E PCIe driver:
- Add j721e DT and driver support for 'num-lanes' for devices that
support x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt
Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is
specific to those TI SoC parts (Peter Robinson)
TI Keystone PCIe controller driver:
- Hold power management references to all PHYs while enabling them to
avoid a race when one provides clocks to others (Siddharth
Vadapalli)
Xilinx XDMA PCIe controller driver:
- Remove redundant dev_err(), since platform_get_irq() and
platform_get_irq_byname() already log errors (Yang Li)
- Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
(Krzysztof Wilczyński)
- Fix xilinx_pl_dma_pcie_init_irq_domain() error return when
irq_domain_add_linear() fails (Harshit Mogalapalli)
MicroSemi Switchtec management driver:
- Do dma_mrpc cleanup during switchtec_pci_remove() to match its devm
ioremapping in switchtec_pci_probe(). Previously the cleanup was
done in stdev_release(), which used stale pointers if stdev->cdev
happened to be open when the PCI device was removed (Daniel
Stodden)
Miscellaneous:
- Convert interrupt terminology from "legacy" to "INTx" to be more
specific and match spec terminology (Damien Le Moal)
- In dw-xdata-pcie, pci_endpoint_test, and vmd, replace usage of
deprecated ida_simple_*() API with ida_alloc() and ida_free()
(Christophe JAILLET)"
* tag 'pci-v6.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (97 commits)
PCI: Fix kernel-doc issues
PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode"
PCI: mediatek-gen3: Fix translation window size calculation
PCI: mediatek: Clear interrupt status before dispatching handler
PCI: keystone: Fix race condition when initializing PHYs
PCI: xilinx-xdma: Fix error code in xilinx_pl_dma_pcie_init_irq_domain()
PCI: xilinx-xdma: Fix uninitialized symbols in xilinx_pl_dma_pcie_setup_irq()
PCI: rcar-gen4: Fix -Wvoid-pointer-to-enum-cast error
PCI: iproc: Fix -Wvoid-pointer-to-enum-cast warning
PCI: dwc: Add dw_pcie_ep_{read,write}_dbi[2] helpers
PCI: dwc: Rename .func_conf_select to .get_dbi_offset in struct dw_pcie_ep_ops
PCI: dwc: Rename .ep_init to .init in struct dw_pcie_ep_ops
PCI: dwc: Drop host prefix from struct dw_pcie_host_ops members
misc: pci_endpoint_test: Use a unique test pattern for each BAR
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI/AER: Use explicit register sizes for struct members
PCI/AER: Decode Requester ID when no error info found
PCI/AER: Use 'Correctable' and 'Uncorrectable' spec terms for errors
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"For this kernel cycle I managed an immutable branch for the PEF2256
WAN framer that has some pin control portions. It already landed in
your tree through the net pull request but here it is mentioned again.
The most interesting is perhaps the Samsung Exynos subdrivers for the
Tensor SoC used in Google Pixel 6 and the ExynosAuto subdriver for
automotive. Along with the earlier merged Tesla FSD subdriver it shows
some of the versatile uses of the Samsung Exynos silicon. It is also
used in the latest version of Axis Communications ARTPEC chips so it
is a very widely deployed SoC family.
We also have the Intel Meteor Lake SoC which I think is for laptops.
It's a pretty interesting chip with Xe graphics and integrated PCH.
Core changes:
- A new PINCTRL_GROUP_DESC() infrastructure macro is added and used
in different drivers, generic group description struct group_desc
is now used all over the place.
New drivers:
- New driver for the Texas Instruments TPS6494 Power Management IC.
- New driver for the Lantic PEF2256 framer pin multiplexer. This IC
has some pins that can be reconfigured in different ways. The
actual driver comes on an immutable branch with the net WAN parts,
the IC is some latest-and-greatest serial line funnel for e.g.
wireless access points.
- New subdriver for the Samsung Exynos Auto V920 pin controller, used
for automotive applications.
- New subdriver for the Samsung "GS101" SoC pin controller, this is
the Google "Tensor" SoC used in the Google Pixel 6.
- New subdriver for the Intel Meteor Point SoC pin controller.
- New subdriver for the Qualcomm SM8650 top level (TLMM) and LPASS
pin controllers.
- New subdriver for the Qualcomm X1E80100 top level (TLMM) pin
controller.
- New subdriver for the Qualcomm SM4450 top level (TLMM) pin
controller.
- The "single" pin controller now supports the Texas Instruments
J7200 SoC.
Improvements:
- Intel has created a new (Intel-)generic pin controller driver that
is now used by all contemporary Intel platforms.
- Intel is now also making use of some cleanup helpers.
- Enble 910 Ohm bias in the Intel Tangier driver.
- The Samsung driver now suppors irq_set_affinity() in it's IRQ chip
giving support for non wake up external gpio interrupts"
* tag 'pinctrl-v6.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: samsung: constify iomem pointers
pinctrl: cy8c95x0: Cache muxed registers
dt-bindings: pinctrl: xilinx: Rename *gpio to *gpio-grp
pinctrl: qcom: lpass-lpi: remove duplicated include
dt-bindings: pinctrl: qcom: drop common properties and allow wakeup-parent
dt-bindings: pinctrl: qcom: drop common properties
dt-bindings: pinctrl: qcom,ipq5018-tlmm: use common TLMM bindings
dt-bindings: pinctrl: qcom,x1e80100-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sm8650-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sm8550-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sdx75-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,sa8775p-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom,qdu1000-tlmm: restrict number of interrupts
dt-bindings: pinctrl: qcom: create common LPASS LPI schema
pinctrl: qcom: sm4450: dd SM4450 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM4450 pinctrl
dt-bindings: pinctrl: qcom,pmic-mpp: clean up example
pinctrl: intel: Add Intel Meteor Point pin controller and GPIO support
pinctrl: renesas: rzg2l: Add input enable to the Ethernet pins
pinctrl: renesas: rzg2l: Add output enable support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- add CMDQ support for mediatek mt8188
- mhuv2: fix channel window status
- qcom: document X1E80100 IPC controller and misc cleanup
- add Versal bindings to xlnx
- Convert to platform remove callback returning void
* tag 'mailbox-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox: (23 commits)
mailbox: mtk-cmdq: Add CMDQ driver support for mt8188
mailbox: mtk-cmdq: Sort cmdq platform data by compatible name
mailbox: mtk-cmdq: Rename gce_plat variable with SoC name postfix
dt-bindings: mailbox: qcom-ipcc: document the X1E80100 Inter-Processor Communication Controller
mailbox: zynqmp-ipi: Convert to platform remove callback returning void
mailbox: tegra-hsp: Convert to platform remove callback returning void
mailbox: sun6i-msgbox: Convert to platform remove callback returning void
mailbox: stm32-ipcc: Convert to platform remove callback returning void
mailbox: qcom-ipcc: Convert to platform remove callback returning void
mailbox: qcom-apcs-ipc: Convert to platform remove callback returning void
mailbox: omap: Convert to platform remove callback returning void
mailbox: mtk-cmdq: Convert to platform remove callback returning void
mailbox: mailbox-test: Convert to platform remove callback returning void
mailbox: imx: Convert to platform remove callback returning void
mailbox: bcm-pdc: Convert to platform remove callback returning void
mailbox: bcm-flexrm: Convert to platform remove callback returning void
mailbox: zynqmp-ipi: fix an Excess struct member kernel-doc warning
dt-bindings: mailbox: add Versal IPI bindings
dt-bindings: mailbox: zynqmp: extend required list
mailbox: arm_mhuv2: Fix a bug for mhuv2_sender_interrupt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds
Pull LED updates from Lee Jones:
"New Drivers:
- Add support for Allwinner A100 RGB LED controller
- Add support for Maxim 5970 Dual Hot-swap controller
New Device Support:
- Add support for AW20108 to Awinic LED driver
New Functionality:
- Extend support for Net speeds to include; 2.5G, 5G and 10G
- Allow tx/rx and cts/dsr/dcd/rng TTY LEDS to be turned on and off
via sysfs if required
- Add support for hardware control in AW200xx
Fix-ups:
- Use safer methods for string handling
- Improve error handling; return proper error values, simplify,
avoid duplicates, etc
- Replace Mutex use with the Completion mechanism
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use generic platform device properties
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Continue work to remove superfluous platform .remove() call-backs
- Remove superfluous/defunct code
- Trivial; whitespace, unused variables, spelling, clean-ups, etc
- Avoid unnecessary duplicate locks
Bug Fixes:
- Repair Kconfig based dependency lists
- Ensure unused dynamically allocated data is freed after use
- Fix support for brightness control
- Add missing sufficient delays during reset to ensure correct
operation
- Avoid division-by-zero issues"
* tag 'leds-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/leds: (45 commits)
leds: trigger: netdev: Add core support for hw not supporting fallback to LED sw control
leds: trigger: panic: Don't register panic notifier if creating the trigger failed
leds: sun50i-a100: Convert to be agnostic to property provider
leds: max5970: Add missing headers
leds: max5970: Make use of dev_err_probe()
leds: max5970: Make use of device properties
leds: max5970: Remove unused variable
leds: rgb: Drop obsolete dependency on COMPILE_TEST
leds: sun50i-a100: Avoid division-by-zero warning
leds: trigger: Remove unused function led_trigger_rename_static()
leds: qcom-lpg: Introduce a wrapper for getting driver data from a pwm chip
leds: gpio: Add kernel log if devm_fwnode_gpiod_get() fails
dt-bindings: leds: qcom,spmi-flash-led: Fix example node name
dt-bindings: leds: aw200xx: Fix led pattern and add reg constraints
dt-bindings: leds: awinic,aw200xx: Add AW20108 device
leds: aw200xx: Add support for aw20108 device
leds: aw200xx: Improve autodim calculation method
leds: aw200xx: Enable disable_locking flag in regmap config
leds: aw200xx: Add delay after software reset
dt-bindings: leds: aw200xx: Remove property "awinic,display-rows"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Device Support:
- Add support for Qualcomm PM8937 PMIC to QCOM SPMI PMIC
Fix-ups:
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Device Tree binding adaptions/conversions/creation
- Improve error handling; return proper error values, simplify,
avoid duplicates, etc
- Continue work to remove superfluous platform .remove() call-backs
- Move some exported symbols into private namespaces
- Clean-up and staticify PM related operations
- Trivial; spelling, whitespace, clean-ups, etc
- Fix include lists; alphabetise, remove unused, explicitly add used
Bug Fixes:
- Use PLATFORM_DEVID_AUTO to ensure multiple duplicate devices can
co-exist
- Ensure debugfs register view is correctly presented
- Fix ordering and value issues in current use of
clk_register_fractional_divider()
- Repair Kconfig based dependency lists"
* tag 'mfd-next-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (50 commits)
mfd: ti_am335x_tscadc: Fix TI SoC dependencies
dt-bindings: mfd: sprd: Add support for UMS9620
mfd: ab8500-sysctrl: Drop ancient charger
mfd: intel-lpss: Fix the fractional clock divider flags
mfd: tps6594: Add null pointer check to tps6594_device_init()
dt-bindings: mfd: pm8008: Clean up example node names
dt-bindings: mfd: hisilicon,hi6421-spmi-pmic: Clean up example
dt-bindings: mfd: hisilicon,hi6421-spmi-pmic: Fix regulator binding
dt-bindings: mfd: hisilicon,hi6421-spmi-pmic: Fix up binding reference
mfd: da9062: Simplify obtaining I2C match data
mfd: syscon: Fix null pointer dereference in of_syscon_register()
mfd: intel-lpss: Don't fail probe on success of pci_alloc_irq_vectors()
mfd: twl6030-irq: Revert to use of_match_device()
mfd: cs42l43: Correct order of include files to be alphabetical
mfd: cs42l43: Correct SoundWire port list
mfd: Fix a few spelling mistakes in PMIC header file comments
mfd: intel-lpss: Provide Intel LPSS PM ops structure
mfd: intel-lpss: Move exported symbols to INTEL_LPSS namespace
mfd: intel-lpss: Adjust header inclusions
mfd: intel-lpss: Use device_get_match_data()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
- The i.MX DSP remoteproc driver adds support for providing a resource
table, in order to enable IPC with the core
- The TI K3 DSP driver is transitioned to remove_new, error messages
are changed to use symbolic error codes, and dev_err_probe() is used
where applicable
- Support for the Qualcomm SC7280 audio, compute and WiFi co-processors
are added to the Qualcomm TrustZone based remoteproc driver
* tag 'rproc-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
remoteproc: qcom_q6v5_pas: Add SC7280 ADSP, CDSP & WPSS
dt-bindings: remoteproc: qcom: sc7180-pas: Add SC7280 compatibles
dt-bindings: remoteproc: qcom: sc7180-pas: Fix SC7280 MPSS PD-names
remoteproc: k3-dsp: Convert to platform remove callback returning void
remoteproc: k3-dsp: Use symbolic error codes in error messages
remoteproc: k3-dsp: Suppress duplicate error message in .remove()
arm64: dts: imx8mp: Add reserve-memory nodes for DSP
remoteproc: imx_dsp_rproc: Add mandatory find_loaded_rsc_table op
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- Support for many new extensions in hwprobe, along with a handful of
cleanups
- Various cleanups to our page table handling code, so we alwayse use
{READ,WRITE}_ONCE
- Support for the which-cpus flavor of hwprobe
- Support for XIP kernels has been resurrected
* tag 'riscv-for-linus-6.8-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (52 commits)
riscv: hwprobe: export Zicond extension
riscv: hwprobe: export Zacas ISA extension
riscv: add ISA extension parsing for Zacas
dt-bindings: riscv: add Zacas ISA extension description
riscv: hwprobe: export Ztso ISA extension
riscv: add ISA extension parsing for Ztso
use linux/export.h rather than asm-generic/export.h
riscv: Remove SHADOW_OVERFLOW_STACK_SIZE macro
riscv; fix __user annotation in save_v_state()
riscv: fix __user annotation in traps_misaligned.c
riscv: Select ARCH_WANTS_NO_INSTR
riscv: Remove obsolete rv32_defconfig file
riscv: Allow disabling of BUILTIN_DTB for XIP
riscv: Fixed wrong register in XIP_FIXUP_FLASH_OFFSET macro
riscv: Make XIP bootable again
riscv: Fix set_direct_map_default_noflush() to reset _PAGE_EXEC
riscv: Fix module_alloc() that did not reset the linear mapping permissions
riscv: Fix wrong usage of lm_alias() when splitting a huge linear mapping
riscv: Check if the code to patch lies in the exit section
riscv: Use the same CPU operations for all CPUs
...
|
|
for interrupt-names
The Loongson-2K0500/2K1000 CPUs have 64 interrupt sources as inputs, and
a route-mapped node handles up to 32 interrupt sources, so two liointc
nodes are defined in dts{i}.
Of course, we have to make sure that the routing outputs ("intx") of the
two nodes do not conflict, i.e. "int0" can only be used as a routing
output for one of them. Therefore, "interrupt-names" should be defined
as "pattern".
In addition, since "interrupt-names" and "interrupts" are one-to-one
correspondence, we pass it to get the corresponding interrupt number in
the driver. Setting it to "required" does not break ABI, because it is
already logically represented as "required".
This fixes dtbs_check warning:
DTC_CHK arch/loongarch/boot/dts/loongson-2k0500-ref.dtb
arch/loongarch/boot/dts/loongson-2k0500-ref.dtb: interrupt-controller@1fe11440: interrupt-names:0: 'int0' was expected
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
arch/loongarch/boot/dts/loongson-2k0500-ref.dtb: interrupt-controller@1fe11440: Unevaluated properties are not allowed ('interrupt-names' was unexpected)
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
DTC_CHK arch/loongarch/boot/dts/loongson-2k1000-ref.dtb
arch/loongarch/boot/dts/loongson-2k1000-ref.dtb: interrupt-controller@1fe01440: interrupt-names:0: 'int0' was expected
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
arch/loongarch/boot/dts/loongson-2k1000-ref.dtb: interrupt-controller@1fe01440: Unevaluated properties are not allowed ('interrupt-names' was unexpected)
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
for reg-names
As we know, the Loongson-2K0500 is a single-core CPU, and the core1-
related register (isr1) does not exist. So "reg" and "reg-names" should
be set to "minItems 2"(main nad isr0).
This fixes dtbs_check warning:
DTC_CHK arch/loongarch/boot/dts/loongson-2k0500-ref.dtb
arch/loongarch/boot/dts/loongson-2k0500-ref.dtb: interrupt-controller@1fe11400: reg-names: ['main', 'isr0'] is too short
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
arch/loongarch/boot/dts/loongson-2k0500-ref.dtb: interrupt-controller@1fe11400: Unevaluated properties are not allowed ('reg-names' was unexpected)
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
arch/loongarch/boot/dts/loongson-2k0500-ref.dtb: interrupt-controller@1fe11400: reg: [[0, 534844416, 0, 64], [0, 534843456, 0, 8]] is too short
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
arch/loongarch/boot/dts/loongson-2k0500-ref.dtb: interrupt-controller@1fe11440: reg-names: ['main', 'isr0'] is too short
From schema: Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml
Acked-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add Loongson SoC boards binding with DT schema format using json-schema.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add the available CPUs in LoongArch binding with DT schema format using
json-schema.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Document the Analog Devices MAX31335 device tree bindings.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20231120120114.48657-1-antoniu.miclaus@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The RV8803 can be wired directly to a PMIC that can wake up an SoC without
the CPU getting interrupts.
Link: https://lore.kernel.org/r/20240108004357.602918-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
- Increase qcom iommu-map maxItems to accommodate SDX55 (five entries) and
SDM845 (sixteen entries) (Krzysztof Kozlowski)
- Describe qcom,pcie-sc8180x clocks and resets accurately (Krzysztof
Kozlowski)
- Describe qcom,pcie-sm8150 clocks and resets accurately (Krzysztof
Kozlowski)
- Correct the qcom "reset-name" property, previously incorrectly called
"reset-names" (Krzysztof Kozlowski)
- Document rockchip optional PCIe reference clock input (Heiko Stuebner)
- Document qcom,pcie-sm8650, based on qcom,pcie-sm8550 (Neil Armstrong)
* pci/dt-bindings:
dt-bindings: PCI: qcom: Document the SM8650 PCIe Controller
dt-bindings: PCI: dwc: rockchip: Document optional PCIe reference clock input
dt-bindings: PCI: qcom: Correct reset-names property
dt-bindings: PCI: qcom: Correct clocks for SM8150
dt-bindings: PCI: qcom: Correct clocks for SC8180x
dt-bindings: PCI: qcom: Adjust iommu-map for different SoC
|
|
- Replace of_device.h with explicit of.h include to untangle header usage
(Rob Herring)
- Add DT and driver support for optional miniPCIe 1.5v and 3.3v regulators
on KingFisher (Wolfram Sang)
* pci/controller/rcar:
PCI: rcar-host: Add support for optional regulators
dt-bindings: PCI: rcar-pci-host: Add optional regulators
PCI: rcar-gen4: Replace of_device.h with explicit of.h include
|
|
- Add j721e DT and driver support for 'num-lanes' for devices that support
x1, x2, or x4 Links (Matt Ranostay)
- Add j721e DT compatible strings and driver support for j784s4 (Matt Ranostay)
- Make TI J721E Kconfig depend on ARCH_K3 since the hardware is specific to
those TI SoC parts (Peter Robinson)
* pci/controller/cadence:
PCI: j721e: Make TI J721E depend on ARCH_K3
PCI: j721e: Add TI J784S4 PCIe configuration
PCI: j721e: Add PCIe 4x lane selection support
PCI: j721e: Add per platform maximum lane settings
dt-bindings: PCI: ti,j721e-pci-*: Add j784s4-pci-* compatible strings
dt-bindings: PCI: ti,j721e-pci-*: Add checks for num-lanes
|
|
Node address doesn't match reg property which is not correct.
Fixes: ba96b2e7974b ("dt-bindings: gpio: gpio-xilinx: Convert Xilinx axi gpio binding to YAML")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Communication Controller
Document the Inter-Processor Communication Controller on the X1E80100 Platform.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Add documentation for AMD-Xilinx Versal platform Inter Processor Interrupt
controller. Versal IPI controller contains buffer-less IPI which do not
have buffers for message passing. For such IPI channels message buffers
are not expected and only notification to/from remote agent is expected.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
"xlnx,ipi-id" is handled as required property but is
missing from binding doc required list of mailbox child node.
Add that to required list. This does not break backward
compatibility but bug in bindings document.
Fixes: 4a855a957936 ("dt-bindings: mailbox: zynqmp_ipi: convert to yaml")
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Rework the compatibles and group devices which have similar interface
(same from Linux driver point of view) as compatible. This allows
smaller of_device_id table in the Linux driver and smaller
allOf:if:then: constraints.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
qcom,ipq8074-apcs-apps-global
qcom,ipq8074-apcs-apps-global compatible is listed in two places: with
and without fallback. Drop the second case to match DTS.
Fixes: 34d8775a0edc ("dt-bindings: mailbox: qcom,apcs-kpss-global: use fallbacks for few variants")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Convert FPGA bridge, all TPMs (finally), and Rockchip HDMI bindings
to schemas
- Improvements in Samsung GPU schemas
- A few more cases of dropping unneeded quotes in schemas
- Merge QCom idle-states txt binding into common idle-states schema
- Add X1E80100, SM8650, SM8650, and SDX75 SoCs to QCom Power Domain
Controller
- Add NXP i.mx8dl to SCU PD
- Add synaptics r63353 panel controller
- Clarify the wording around the use of 'wakeup-source' property
- Add a DTS coding style doc
- Add smi vendor prefix
- Fix DT_SCHEMA_FILES incorrect matching of paths outside the kernel
tree
- Disable sysfb (e.g. EFI FB) when simple-framebuffer node is present
- Fix double free in of_parse_phandle_with_args_map()
- A couple of kerneldoc fixes
* tag 'devicetree-for-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (37 commits)
of: unittest: Fix of_count_phandle_with_args() expected value message
dt-bindings: fpga: altera: Convert bridge bindings to yaml
dt-bindings: fpga: Convert bridge binding to yaml
dt-bindings: vendor-prefixes: Add smi
dt-bindings: power: Clarify wording for wakeup-source property
of: Fix double free in of_parse_phandle_with_args_map
dt-bindings: ignore paths outside kernel for DT_SCHEMA_FILES
drivers: of: Fixed kernel doc warning
dt-bindings: tpm: Document Microsoft fTPM bindings
dt-bindings: tpm: Convert IBM vTPM bindings to DT schema
dt-bindings: tpm: Convert Google Cr50 bindings to DT schema
dt-bindings: tpm: Consolidate TCG TIS bindings
dt-bindings: display: rockchip,inno-hdmi: Document RK3128 compatible
dt-bindings: arm: Add remote etm dt-binding
dt-bindings: mmc: sdhci-pxa: Fix 'regs' typo
media: dt-bindings: samsung,s5p-mfc: Fix iommu properties schemas
dt-bindings: display: panel: Add synaptics r63353 panel controller
dt-bindings: arm: merge qcom,idle-state with idle-state
dt-bindings: drm: rockchip: convert inno_hdmi-rockchip.txt to yaml
dt-bindings: cache: qcom,llcc: correct QDU1000 reg entries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a bunch of cleanups and simplifications across the
board, as well as a number of small fixes.
Perhaps the most notable change here is the addition of an API that
allows PWMs to be used in atomic contexts, which is useful when time-
critical operations are involved, such as using a PWM to generate IR
signals.
Finally, I have decided to step down as PWM subsystem maintainer. Due
to other responsibilities I have lately not been able to find the time
that the subsystem deserves and Uwe, who has been helping out a lot
for the past few years and has many things planned for the future, has
kindly volunteered to take over. I have no doubt that he will be a
suitable replacement"
* tag 'pwm/for-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
MAINTAINERS: pwm: Thierry steps down, Uwe takes over
pwm: linux/pwm.h: fix Excess kernel-doc description warning
pwm: Add pwm_apply_state() compatibility stub
pwm: cros-ec: Drop documentation for dropped struct member
pwm: Drop two unused API functions
pwm: lpc18xx-sct: Don't modify the cached period of other PWM outputs
pwm: meson: Simplify using dev_err_probe()
pwm: stmpe: Silence duplicate error messages
pwm: Reduce number of pointer dereferences in pwm_device_request()
pwm: crc: Use consistent variable naming for driver data
pwm: omap-dmtimer: Drop locking
dt-bindings: pwm: ti,pwm-omap-dmtimer: Update binding for yaml
media: pwm-ir-tx: Trigger edges from hrtimer interrupt context
pwm: bcm2835: Allow PWM driver to be used in atomic context
pwm: Make it possible to apply PWM changes in atomic context
pwm: renesas: Remove unused include
pwm: Replace ENOTSUPP with EOPNOTSUPP
pwm: Rename pwm_apply_state() to pwm_apply_might_sleep()
pwm: Stop referencing pwm->chip
pwm: Update kernel doc for struct pwm_chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID updates from Jiri Kosina:
- assorted functional fixes for hid-steam ported from SteamOS betas
(Vicki Pfau)
- fix for custom sensor-hub sensors (hinge angle sensor and LISS
sensors) not working (Yauhen Kharuzhy)
- functional fix for handling Confidence in Wacom driver (Jason
Gerecke)
- support for Ilitek ili2901 touchscreen (Zhengqiao Xia)
- power management fix for Wacom userspace battery exporting
(Tatsunosuke Tobita)
- rework of wait-for-reset in order to reduce the need for
I2C_HID_QUIRK_NO_IRQ_AFTER_RESET qurk; the success rate is now 50%
better, but there are still further improvements to be made (Hans de
Goede)
- greatly improved coverage of Tablets in hid-selftests (Benjamin
Tissoires)
- support for Nintendo NSO controllers -- SNES, Genesis and N64 (Ryan
McClelland)
- support for controlling mcp2200 GPIOs (Johannes Roith)
- power management improvement for EHL OOB wakeup in intel-ish
(Kai-Heng Feng)
- other assorted device-specific fixes and code cleanups
* tag 'hid-for-linus-2024010801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (53 commits)
HID: amd_sfh: Add a new interface for exporting ALS data
HID: amd_sfh: Add a new interface for exporting HPD data
HID: amd_sfh: rename float_to_int() to amd_sfh_float_to_int()
HID: i2c-hid: elan: Add ili2901 timing
dt-bindings: HID: i2c-hid: elan: Introduce Ilitek ili2901
HID: bpf: make bus_type const in struct hid_bpf_ops
HID: make ishtp_cl_bus_type const
HID: make hid_bus_type const
HID: hid-steam: Add gamepad-only mode switched to by holding options
HID: hid-steam: Better handling of serial number length
HID: hid-steam: Update list of identifiers from SDL
HID: hid-steam: Make client_opened a counter
HID: hid-steam: Clean up locking
HID: hid-steam: Disable watchdog instead of using a heartbeat
HID: hid-steam: Avoid overwriting smoothing parameter
HID: magicmouse: fix kerneldoc for struct magicmouse_sc
HID: sensor-hub: Enable hid core report processing for all devices
HID: wacom: Add additional tests of confidence behavior
HID: wacom: Correct behavior when processing some confidence == false touches
HID: nintendo: add support for nso controllers
...
|
