| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
When trying to play a 8kHz file with codec in slave mode we get the following
error on a mx28evk:
$ aplay -Dhw:0,0 stereo_8k.wav
Playing WAVE 'stereo_8k.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
[ 21.218647] sgtl5000 0-000a: PLL not supported in slave mode
[ 21.224559] sgtl5000 0-000a: 128 ratio is not supported. SYS_MCLK needs to be 256, 384 or 512 * fs
[ 21.233687] sgtl5000 0-000a: ASoC: can't set sgtl5000 hw params: -22
aplay: set_params:1123: Unable to install hw params:
This error happens because we are using 'sys_fs' instead of 'frame_rate' in the
valid ratio check.
Use the real'frame_rate' so that the ratio is correctly calculated and the
playback can run.
sgtl5000 codec manual states that in 'Synchronous SYS_MCLK input' mode that the
following SYS_CLK frequencies are allowed: 256*fs, 384*fs, 512*fs.
, where fs is the sampling frequency, which can be in the range of:
8, 11.025, 16, 22.5, 32, 44.1, 48, 96 kHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
When running the codec as slave, the master should generate MCLK in the range of
256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK input mode.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DLink GO-USB-N150 with revision B1 uses this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a potential race when probing the TLB in TLBL/M/S exception
handlers for a matching entry. Between the time we hit a TLBL/S/M
exception and the time we get to execute the TLBP instruction, the
HTW may have replaced the TLB entry we are interested in hence the TLB
probe may fail. However, in the existing handlers, we never checked the
status of the TLBP (ie check the result in the C0/Index register). We
fix this by adding such a check when the core implements the HTW. If
we couldn't find a matching entry, we return back and try again.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8599/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Cc: stable@vger.kernel.org # 3.12+
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes: de4901933f6d ("arm: mm: Add support for PJ4B cpu and init routines")
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull "mvebu fixes for v3.18 (round 2)" frm Jason Cooper:
- mvebu
- coherency.c needed an of_node_put()
* tag 'mvebu-fixes-3.18-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add missing of_node_put() call in coherency.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull "Samsung defconfig update for v3.18" from Kukjin Kim:
- enable max77802 rtc and clock drivers for exynos_defconfig
: enable the kernel config options to have the drivers for
max77802 including rtc and 2-ch 32kHz clock outputs
* tag 'samsung-defconfig-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable max77802 rtc and clock drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull "Samsung fixes for v3.18" from Kukjin Kim:
- explicitly set dr_mode on exynos5250-snow
this is required when kernel is built with USB gadget support.
* tag 'samsung-fixes-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5250-snow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The crazy gic_arch_extn thing that Tegra uses contains multiple
references to the irq field in struct irq_data, and uses this
to directly poke hardware register.
But irq is the *virtual* irq number, something that has nothing
to do with the actual HW irq (stored in the hwirq field). And once
we put the stacked domain code in action, the whole thing explodes,
as these two values are *very* different:
root@bacon-fat:~# cat /proc/interrupts
CPU0 CPU1
16: 25801 2075 GIC 29 twd
17: 0 0 GIC 73 timer0
112: 0 0 GPIO 58 c8000600.sdhci cd
123: 0 0 GPIO 69 c8000200.sdhci cd
279: 1126 0 GIC 122 serial
281: 0 0 GIC 70 7000c000.i2c
282: 0 0 GIC 116 7000c400.i2c
283: 0 0 GIC 124 7000c500.i2c
284: 300 0 GIC 85 7000d000.i2c
[...]
Just replacing all instances of irq with hwirq fixes the issue.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the manual transition back to SND_SOC_BIAS_STANDBY in resume. This
is already be automatically handled by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. While we are at it also remove the unused codec field from
the cq93vc struct so the whole probe function can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Broadwell, the ADSP FW don't support loopback record volume tuning,
so here remove this control.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "changed" variable should be set to false at the start.
Fixes: a35daac77a03 ('ASoC: sigmadsp: Add support for fw v2')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
into drm-fixes
one fix for PX laptops.
* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: report disconnected for LVDS/eDP with PX if ddc fails
|
|
If ddc fails, presumably the i2c mux (and hopefully the signal
mux) are switched to the other GPU so don't fetch the edid from
the vbios so that the connector reports disconnected.
bug:
https://bugzilla.opensuse.org/show_bug.cgi?id=904417
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.
Fixes: 18ad51dd342a ("powerpc: Add VDSO version of getcpu")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The flag passed to ioda_eeh_phb_reset() should be EEH_RESET_DEACTIVATE,
which is translated to OPAL_DEASSERT_RESET or something else by the
EEH backend accordingly.
The patch replaces OPAL_DEASSERT_RESET with EEH_RESET_DEACTIVATE for
ioda_eeh_phb_reset().
Cc: stable@vger.kernel.org
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Obviously I had wrong format given to the PE state output from
/sys/bus/pci/devices/xxxx/eeh_pe_state with some typoes, which
was introduced by commit 2013add4ce73. The patch fixes it up.
Fixes: 2013add4ce73 ("powerpc/eeh: Show hex prefix for PE state sysfs")
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
On pseries system (LPAR) xmon failed to enter when running in LE mode,
system is hunging. Inititating xmon will lead to such an output on the
console:
SysRq : Entering xmon
cpu 0x15: Vector: 0 at [c0000003f39ffb10]
pc: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
lr: c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
sp: c0000003f39ffc70
msr: 8000000000009033
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
Bad kernel stack pointer fafb4b0 at eca7cc4
cpu 0x15: Vector: 300 (Data Access) at [c000000007f07d40]
pc: 000000000eca7cc4
lr: 000000000eca7c44
sp: fafb4b0
msr: 8000000000001000
dar: 10000000
dsisr: 42000000
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop
xmon: WARNING: bad recursive fault on cpu 0x15
The root cause is that xmon is calling RTAS to turn off the surveillance
when entering xmon, and RTAS is requiring big endian parameters.
This patch is byte swapping the RTAS arguments when running in LE mode.
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The current HMI event structure is an ABI and carries a version field to
accommodate future changes without affecting/rearranging current structure
members that are valid for previous versions.
The current version check "if (hmi_evt->version != OpalHMIEvt_V1)"
doesn't accomodate the fact that the version number may change in
future.
If firmware starts returning an HMI event with version > 1, this check
will fail and no HMI information will be printed on older kernels.
This patch fixes this issue.
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Reword changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
fadbe0cd
In commit fadbe0cd5292851608e2e01b91d9295fa287b9fe entitled "staging:
rtl8188eu:Remove rtw_zmalloc(), wrapper for kzalloc()", the author failed
to note that the original code in the wrapper tested whether the caller
could sleep, and set the flags argument to kzalloc() appropriately.
After the patch, GFP_KERNEL is used unconditionally. Unfortunately, several
of the routines may be entered from an interrupt routine and generate
a BUG splat for every such call. Routine rtw_sitesurvey_cmd() is used in the
example below:
BUG: sleeping function called from invalid context at mm/slub.c:1240
in_atomic(): 1, irqs_disabled(): 0, pid: 756, name: wpa_supplicant
INFO: lockdep is turned off.
CPU: 2 PID: 756 Comm: wpa_supplicant Tainted: G WC O 3.18.0-rc4+ #34
Hardware name: TOSHIBA TECRA A50-A/TECRA A50-A, BIOS Version 4.20 04/17/2014
ffffc90005557000 ffff880216fafaa8 ffffffff816b0bbf 0000000000000000
ffff8800c3b58000 ffff880216fafac8 ffffffff8107af77 0000000000000001
0000000000000010 ffff880216fafb18 ffffffff811b06ce 0000000000000000
Call Trace:
[<ffffffff816b0bbf>] dump_stack+0x4e/0x71
[<ffffffff8107af77>] __might_sleep+0xf7/0x120
[<ffffffff811b06ce>] kmem_cache_alloc_trace+0x4e/0x1f0
[<ffffffffa0888226>] ? rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
[<ffffffffa0888226>] rtw_sitesurvey_cmd+0x56/0x2a0 [r8188eu]
[<ffffffffa088f00d>] rtw_do_join+0x22d/0x370 [r8188eu]
[<ffffffffa088f6e8>] rtw_set_802_11_ssid+0x218/0x3d0 [r8188eu]
[<ffffffffa08c3ca5>] rtw_wx_set_essid+0x1e5/0x410 [r8188eu]
[<ffffffffa08c3ac0>] ? rtw_wx_get_rate+0x50/0x50 [r8188eu]
[<ffffffff816938f1>] ioctl_standard_iw_point+0x151/0x3f0
[<ffffffff81693d52>] ioctl_standard_call+0xb2/0xe0
[<ffffffff81597df7>] ? rtnl_lock+0x17/0x20
[<ffffffff816945a0>] ? iw_handler_get_private+0x70/0x70
[<ffffffff81693ca0>] ? call_commit_handler+0x40/0x40
[<ffffffff81693256>] wireless_process_ioctl+0x176/0x1c0
[<ffffffff81693e79>] wext_handle_ioctl+0x69/0xc0
[<ffffffff8159fe79>] dev_ioctl+0x309/0x5e0
[<ffffffff810be9c7>] ? call_rcu+0x17/0x20
[<ffffffff8156a472>] sock_ioctl+0x142/0x2e0
[<ffffffff811e0c70>] do_vfs_ioctl+0x300/0x520
[<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff81101514>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff810102bc>] ? do_audit_syscall_entry+0x6c/0x70
[<ffffffff811e0f11>] SyS_ioctl+0x81/0xa0
[<ffffffff816ba1d2>] system_call_fastpath+0x12/0x17
Additional routines that generate this BUG are rtw_joinbss_cmd(),
rtw_dynamic_chk_wk_cmd(), rtw_lps_ctrl_wk_cmd(), rtw_rpt_timer_cfg_cmd(),
rtw_ps_cmd(), report_survey_event(), report_join_res(), survey_timer_hdl(),
and rtw_check_bcn_info().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: navin patidar <navin.patidar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-11-26
Please pull this little batch of fixes intended for the 3.18 stream...
For the iwlwifi one, Emmanuel says:
"Not all the firmware know how to handle the HOT_SPOT_CMD.
Make sure that the firmware will know this command before
sending it. This avoids a firmware crash."
Along with that, Larry sends a pair of rtlwifi fixes to address some
discrepancies from moving drivers out of staging. Larry says:
"These two patches are needed to fix a regression introduced when
driver rtl8821ae was moved from staging to the regular wireless tree."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This can be a NOP because we forward dma_{alloc,free}_noncoherent to
dma_{alloc,free}_coherent.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas Graf says:
====================
bridge: Fix missing Netlink message validations
Adds various missing length checks in the bridging code for Netlink
messages and corresponding attributes provided by user space.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only search for IFLA_EXT_MASK if the message actually carries a
ifinfomsg header and validate minimal length requirements for
IFLA_EXT_MASK.
Fixes: 6cbdceeb ("bridge: Dump vlan information from a bridge port")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: c2d3babf ("bridge: implement multicast fast leave")
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ndo_bridge_setlink() is currently only called on the slave if
IFLA_AF_SPEC is set but this is a very fragile assumption and may
change in the future.
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: a77dcb8c8 ("be2net: set and query VEB/VEPA mode of the PF interface")
Fixes: 815cccbf1 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Payload is currently accessed blindly and may exceed valid message
boundaries.
Fixes: 407af3299 ("bridge: Add netlink interface to configure vlans on bridge ports")
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull kvm fixes from Paolo Bonzini:
"Last minute KVM/ARM fixes; even the generic change actually affects
nothing but ARM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: fix kvm_is_mmio_pfn() and rename to kvm_is_reserved_pfn()
arm/arm64: kvm: drop inappropriate use of kvm_is_mmio_pfn()
arm/arm64: KVM: vgic: Fix error code in kvm_vgic_create()
arm64: KVM: Handle traps of ICC_SRE_EL1 as RAZ/WI
arm64: KVM: fix unmapping with 48-bit VAs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
|
|
|
|
|
|
The commit 3b57de958e2a brought the support for a different amount of
the filter bins, but didn't update the platform driver that without
CONFIG_OF.
Fixes: 3b57de958e2a (net: stmmac: Support devicetree configs for mcast
and ucast filter entries)
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: dsa: bcm_sf2: misc bugfixes
This patch series contains two bug fixes:
- first patch fixes an issue on the error path of the driver where we could
have left some of our registers mapped
- second patch enforces the use of a software reset of the switch to guarantee
the HW is in a consistent state prior to software initialization
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our boot agent may have left the switch in an certain configuration
state, make sure we issue a software reset prior to configuring the
switch in order to ensure the HW is in a consistent state, in particular
transmit queues and internal buffers.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we fail to ioremap() one of our registers, we would be leaking
existing mappings, unwind those accordingly on errors.
Fixes: 246d7f773c13 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
